找回密码
 立即注册

QQ登录

只需一步,快速开始

搜索
广告投放联系QQ68610888
查看: 3875|回复: 0

腾达Tenda R60 8M/16M flash 编程器原厂2.0.0.2固件

[复制链接]
发表于 2013-12-5 16:47 | 显示全部楼层 |阅读模式
因为网上没找到原厂固件,所以趁着换Flash的时候备份了原装8MFlash里面的固件,备份后为防止刷入16MFlash NVram找不到,将8M信息重新填入8-16M空间,经过验证可以正常启动。

附件共有7个,每每天只能传两个,慢慢传上来。下载后请去掉.pdf后用7Z解压。










16M启动信息如下:

ecompressing...done


CFE version 5.100.138.22 based on BBP 1.0.37 for BCM947XX (32bit,SP,LE)
Build Date: Sat Mar 31 16:54:11 CST 2012 (root@linux-6091)
Copyright (C) 2000-2008 Broadcom Corporation.

Init Arena
Init Devs.
Boot partition size = 131072(0x20000)
Found an ST compatible serial flash with 256 64KB blocks; total size 16MB
et0: Broadcom BCM47XX 10/100/1000 Mbps Ethernet Controller 5.100.138.22
CPU type 0x19749: 500MHz
Tot mem: 65536 KBytes

CFE mem:    0x80700000 - 0x80798520 (623904)
Data:       0x8072E340 - 0x80731590 (12880)
BSS:        0x80731590 - 0x80732520 (3984)
Heap:       0x80732520 - 0x80796520 (409600)
Stack:      0x80796520 - 0x80798520 (8192)
Text:       0x80700000 - 0x8072E340 (189248)

Device eth0:  hwaddr C8-3A-35-38-72-D0, ipaddr 192.168.1.1, mask 255.255.255.0
        gateway not set, nameserver not set
Loader:raw Filesys:raw Dev:flash0.os File: Optionsnull)
Loading: ...... 3584820 bytes read
Entry at 0x80001000
Closing network.
Starting program at 0x80001000
Linux version 2.6.22 (root@linux-jacksom) (gcc version 4.2.3) #8 PREEMPT Wed Jul 11 09:48:03 CST 2012
CPU revision is: 00019749
Found an ST compatible serial flash with 256 64KB blocks; total size 16MB
wombo_reset set to gpio 22
Determined physical RAM map:
memory: 04000000 @ 00000000 (usable)
Built 1 zonelists.  Total pages: 16256
Kernel command line: root=/dev/mtdblock2 console=ttyS0,115200 init=/sbin/preinit
Primary instruction cache 32kB, physically tagged, 4-way, linesize 32 bytes.
Primary data cache 32kB, 4-way, linesize 32 bytes.
Synthesized TLB refill handler (20 instructions).
Synthesized TLB load handler fastpath (32 instructions).
Synthesized TLB store handler fastpath (32 instructions).
Synthesized TLB modify handler fastpath (31 instructions).
PID hash table entries: 256 (order: 8, 1024 bytes)
CPU: BCM5357 rev 2 at 500 MHz
Using 250.000 MHz high precision timer.
Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
Memory: 60976k/65536k available (2772k kernel code, 4504k reserved, 559k data, 168k init, 0k highmem)
Mount-cache hash table entries: 512
NET: Registered protocol family 16
SCSI subsystem initialized
PCI: no core
PCI: no core
PCI: Fixing up bus 0
NET: Registered protocol family 2
Time: MIPS clocksource has been installed.
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
TCP established hash table entries: 2048 (order: 2, 16384 bytes)
TCP bind hash table entries: 2048 (order: 1, 8192 bytes)
TCP: Hash tables configured (established 2048 bind 2048)
TCP reno registered
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
squashfs: version 3.2-r2 (2007/01/15) Phillip Lougher
fuse init (API version 7.8)
io scheduler noop registered (default)
HDLC line discipline: version $Revision: 1.1.1.1 $, maxframe=4096
N_HDLC line discipline registered.
Serial: 8250/16550 driver $Revision: 1.1.1.1 $ 4 ports, IRQ sharing disabled
serial8250: ttyS0 at MMIO 0x0 (irq = 8) is a 16550A
loop: module loaded
PPP generic driver version 2.4.2
PPP Deflate Compression module registered
PPP BSD Compression module registered
PPP MPPE Compression module registered
NET: Registered protocol family 24
pflash: found no supported devices
Boot partition size = 131072(0x20000)
sflash: squash filesystem with lzma found at block 21
Creating 4 MTD partitions on "sflash":
0x00000000-0x00020000 : "boot"
0x00020000-0x00ff0000 : "linux"
0x00154f20-0x00ff0000 : "rootfs"
0x00ff0000-0x01000000 : "nvram"
nflash: found no supported devices
nf_conntrack version 0.5.0 (512 buckets, 4096 max)
IPv4 over IPv4 tunneling driver
GRE over IPv4 tunneling driver
ip_tables: (C) 2000-2006 Netfilter Core Team
TCP cubic registered
NET: Registered protocol family 1
NET: Registered protocol family 17
802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>
All bugs added by David S. Miller <davem@redhat.com>
VFS: Mounted root (squashfs filesystem) readonly.
Freeing unused kernel memory: 168k freed
Warning: unable to open an initial console.
Failed to execute /init
Algorithmics/MIPS FPU Emulator v1.5
[sighandler]: No more events to be processed, quitting.
[cleanup]: Waiting for children.
[cleanup]: All children terminated.
load_emf:253-----load_emf-----
insmod: emf.ko: no module by that name found
insmod: igs.ko: no module by that name found
et: module license 'Proprietary' taints kernel.
et_module_init: passivemode set to 0x1
et_module_init: et_txq_thresh set to 0x0
eth0: Broadcom BCM47XX 10/100/1000 Mbps Ethernet Controller 5.100.138.2205
insmod: bcm57xx.ko: no module by that name found
wl_module_init: passivemode set to 0x1
eth1: Broadcom BCM4347 802.11 Wireless Controller 5.100.138.2205
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
Initializing USB Mass Storage driver...
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
usbcore: registered new interface driver usblp
drivers/usb/class/usblp.c: v0.13: USB Printer Device Class driver
wombo_reset set to gpio 22
ohci_hcd 0000:00:04.0: OHCI Host Controller
ohci_hcd 0000:00:04.0: new USB bus registered, assigned bus number 1
ohci_hcd 0000:00:04.0: irq 5, io mem 0x18009000
CJ++ PRODUCT commit to nvram : 0/0/206
USB hotplug_usb detected product:  0/0/206
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
printer device not found
wombo_reset set to gpio 22
ehci_hcd 0000:00:04.1: EHCI Host Controller
ehci_hcd 0000:00:04.1: new USB bus registered, assigned bus number 2
ehci_hcd 0000:00:04.1: EHCI Fastpath: New EHCI driver starting
ehci_hcd 0000:00:04.1: irq 5, io mem 0x18004000
ehci_hcd 0000:00:04.1: USB 0.0 started, EHCI 1.00, driver 10 Dec 2004
CJ++ PRODUCT commit to nvram : 0/0/206
USB hotpusb usb2: configuration #1 chosen from 1 choice
lug_usb detected product:  0/0/206
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
ehci_hcd 0000:00:04.1: Ehci port 2 had hsic capability
usb 2-2: new high speed USB device using ehci_hcd and address 2
ehci_hcd 0000:00:04.1: Ehci port 2 had hsic capability
CJ++ PRODUCT commit to nvram : a5c/bd17/1
USB hotplug_usb detected product:  a5c/bd17/1
usb 2-2: configuration #1 chosen from 1 choice
printer device not found
printer device not found
rc_signal: signalling RESTART
Symbol usb_register_driver is being used by a non-GPL module, which will not be allowed in the future
Please see the file Documentation/feature-removal-schedule.txt in the kernel source tree for more details.
Symbol usb_deregister is being used by a non-GPL module, which will not be allowed in the future
Please see the file Documentation/feature-removal-schedule.txt in the kernel source tree for more details.
EHCI Fastpath: usb_dev 83b17400
EHCI Fastpath: bus 83d82200
EHCI Fastpath: Hub 83b17800
ehci_hcd 0000:00:04.1: EHCI Fastpath: Got the bypass device command in EHCI 83b17400
EHCI Fastpath: usb_dev 83b17400
EHCI Fastpath: bus 83d82200
EHCI Fastpath: Hub 83b17800
ehci_hcd 0000:00:04.1: EHCI Fastpath: Got the bypass callback command in EHCI c0283608
EHCI Fastpath: usb_dev 83b17400
EHCI Fastpath: bus 83d82200
EHCI Fastpath: Hub 83b17800
ehci_hcd 0000:00:04.1: EHCI Fastpath: Got the bypass fastpath pool command in EHCI 835c3780
EHCI Fastpath: usb_dev 83b17400
EHCI Fastpath: bus 83d82200
EHCI Fastpath: Hub 83b17800
ehci_hcd 0000:00:04.1: EHCI Fastpath: Got the RH bypass command in EHCI for EP #0 0004
ehci_hcd 0000:00:04.1: EHCI Fastpath: release native dummy qtd and alloc new one
ehci_hcd 0000:00:04.1: EHCI Fastpath: EP 834077ec QH a3b60100 dummy a33f0000
EHCI Fastpath: usb_dev 83b17400
EHCI Fastpath: bus 83d82200
EHCI Fastpath: Hub 83b17800
ehci_hcd 0000:00:04.1: EHCI Fastpath: Got the RH bypass command in EHCI for EP #1 0012
ehci_hcd 0000:00:04.1: EHCI Fastpath: release native dummy qtd and alloc new one
ehci_hcd 0000:00:04.1: EHCI Fastpath: EP 834077a4 QH a3b60180 dummy a33f0060
EHCI Fastpath: EP in 18 EP in2 19 EP out 4
bcm_rpc_up: waiting to be connected
bcm_rpc_buf_recv_mgn_high: Reason: 0 Dongle Version: 0x5648a89
bcm_rpc_buf_recv_mgn_high: Connected!
eth2: Broadcom BCMa8e4 802.11 Wireless Controller 5.100.138.2205
usbcore: registered new interface driver dbus_usbdev
wl1 is up in 0 sec
sysinit: done
Hit enter to continue...init server success.1..
No need to start gpio thread.
main_loop: TIMER
main_loop: IDLE
start gpiod...
start_lan: br0
NET: Setting vlan1: dev_set_allmulti(master, 1)
br0 hw addr to c8:3a:35:38:72:d0
vlan1: Operation not supported
vlan1: dev_set_promiscuity(master, 1)
device eth0 entered promiscuous mode
device vlan1 entered promiscuous mode
eth1: Operation not supported
wlconf: PHYTYPE: 4
eth1: Invalid argument
eth1: Invalid argument
eth1: Operation not supported
eth1: Operation not supported
device eth1 entered promiscuous mode
wlconf: PHYTYPE: 4
eth2: Invalid argument
eth2: Invalid argument
eth2: Operation not supported
eth2: Operation not supported
device eth2 entered promiscuous mode
NET: Setting br1 hw addr to cbr0: port 3(eth2) entering learning state
8:3a:35:38:72:d1br0: port 2(eth1) entering learning state

br0: port 1(vlan1) entering learning state
br0: topology change detected, propagating
br0: port 3(eth2) entering forwarding state
br0: topology change detected, propagating
br0: port 2(eth1) entering forwarding state
br0: topology change detected, propagating
br0: port 1(vlan1) entering forwarding state
start_emf:236-----start_emf-----
killall: wps_monitor: no process killed
CJ++ printer disabled
main_loop: TIMER
main_loop: IDLE
Hit enter to continue...main.c check network 192.168.0.1 success
main.c check network 192.168.0.1 success


Yes:

      ****** WeLoveLinux ******

Welcome to ...
cgi/main.c check network ip start
acsd: selected channel spec: 0x1e97
multwan init ok.
open /proc/tdproc/lanip failed
killall: dhcps: no process killed
Init tQoS dev success.
adding /dev/tQoS...
adding /dev/ufilmac_filter_init.....
ter...
ipmacbind_init.....
groupip_init.....
client_filter_init.....
start url_filter_init...................
killall: ddns: no process killed
killall: ddns: no process killed
killall: ddns: no process killed
rm: cannot remove '/etc/ddns_*': No such file or directory
killall: dhcps_guest: no process killed
Hit enter to continue...open /dev/gsbmac failed.
open /dev/fence failed.
bad.map=00000
bad_bit=0
open /dev/fence failed.
ipop_bit:0000000
ipop_bit=0
open /dev/fence failed.
set port 0 to AUTO
httpd listen ip = 192.168.0.1 port = 80
webs: Listening for HTTP requests at address 192.168.0.1
init web server success: cgi/main.c
Hit enter to continue...eth1: received packet with  own address as source address
return 26 bytes ie
Restart logserver
killall: logserver: no process killed
logserver.c check network 192.168.0.1 success
Restart sntp
killall: sntp: no process killed
sntp.c check network 192.168.0.1 success
pcookie:admin
aspHomepage:132----connect_tpye=0----
aspHomepage:141----user_name=----
aspHomepage:150----user_password=----
aspHomepage:178----wireless_password=microsoft----
aspHomepage:195----wireless_way=0----
/test



BusyBox v1.7.2 (2012-02-08 07:39:16 CST) built-in shell (ash)
Enter 'help' for a list of built-in commands.

#
#
#
# ps
  PID  Uid        VSZ Stat Command

    1 admin      2164 S   /sbin/preinit
    2 admin           SW< [kthreadd]
    3 admin           SW< [ksoftirqd/0]
    4 admin           SW< [events/0]
    5 admin           SW< [khelper]
   22 admin           SW< [kblockd/0]
   44 admin           SW  [pdflush]
   45 admin           SW  [pdflush]
   46 admin           SW< [kswapd0]
   47 admin           SW< [aio/0]
  328 admin           SW< [mtdblockd]
  987 admin           SW< [khubd]
1054 admin      2160 S   cfmd
1055 admin      2160 S   cfmd
1056 admin      2160 S   cfmd
1058 admin      1624 S   gpiod
1114 admin      1404 S   eapd
1120 admin      1908 S   nas
1126 admin      1472 S   acsd
1140 admin      3084 S   httpd
1143 admin      2480 S   netctrl
1146 admin      2136 S   multiWAN
1147 admin      2136 S   multiWAN
1148 admin      2136 S   multiWAN
1157 admin      2480 S   netctrl
1158 admin      2480 S   netctrl
1314 admin      2236 S   dhcps
1332 admin      2236 S   dhcps_guest -C /etc/dhcps_guest.conf -l /etc/dhcps_gu
1333 admin      3084 S   httpd
1336 admin      3084 S   httpd
1340 admin      2068 S   /bin/logserver
1344 admin      2064 S   /bin/sntp
1345 admin      1388 S   /bin/sh
1348 admin      1388 R   ps
#
#
#
# ifconfig
br0       Link encap:Ethernet  HWaddr C8:3A:35:38:720  
          inet addr:192.168.0.1  Bcast:192.168.0.255  Mask:255.255.255.0
          UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1
          RX packets:1374 errors:0 dropped:0 overruns:0 frame:0
          TX packets:1597 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:0
          RX bytes:128206 (125.2 KiB)  TX bytes:1278383 (1.2 MiB)

br1       Link encap:Ethernet  HWaddr C8:3A:35:38:721  
          inet addr:192.168.2.1  Bcast:192.168.2.255  Mask:255.255.255.0
          UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1
          RX packets:0 errors:0 dropped:0 overruns:0 frame:0
          TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:0
          RX bytes:0 (0.0 B)  TX bytes:0 (0.0 B)

eth0      Link encap:Ethernet  HWaddr C8:3A:35:38:720  
          UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1
          RX packets:0 errors:0 dropped:0 overruns:0 frame:0
          TX packets:313 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:1000
          RX bytes:0 (0.0 B)  TX bytes:43946 (42.9 KiB)
          Interrupt:4 Base address:0x2000

eth1      Link encap:Ethernet  HWaddr C8:3A:35:38:720  
          UP BROADCAST RUNNING ALLMULTI MULTICAST  MTU:1500  Metric:1
          RX packets:1364 errors:0 dropped:0 overruns:0 frame:58863
          TX packets:1906 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:1000
          RX bytes:146443 (143.0 KiB)  TX bytes:1338555 (1.2 MiB)
          Interrupt:3 Base address:0x1000

eth2      Link encap:Ethernet  HWaddr C8:3A:35:38:724  
          UP BROADCAST RUNNING ALLMULTI MULTICAST  MTU:1500  Metric:1
          RX packets:0 errors:0 dropped:0 overruns:0 frame:13
          TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:1000
          RX bytes:0 (0.0 B)  TX bytes:0 (0.0 B)

lo        Link encapocal Loopback  
          inet addr:127.0.0.1  Mask:255.0.0.0
          UP LOOPBACK RUNNING MULTICAST  MTU:16436  Metric:1
          RX packets:8 errors:0 dropped:0 overruns:0 frame:0
          TX packets:8 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:0
          RX bytes:1317 (1.2 KiB)  TX bytes:1317 (1.2 KiB)

vlan1     Link encap:Ethernet  HWaddr C8:3A:35:38:720  
          UP BROADCAST RUNNING ALLMULTI MULTICAST  MTU:1500  Metric:1
          RX packets:0 errors:0 dropped:0 overruns:0 frame:0
          TX packets:313 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:0
          RX bytes:0 (0.0 B)  TX bytes:43946 (42.9 KiB)

# reboot
Terminated
Sending SIGTERM to all processes
cfmd -> Term_Sig_entry [15]...
cfmd -> Term_Sig_entry [15]...
netctl -> Term_Sig_entry [15]...
multiWAN -> Term_Sig_entry [15]...
multiWAN -> Term_Sig_entry [15]...
netctl -> Term_Sig_entry [15]...
Terminated
# Sending SIGKILL to all processesRestarting system.
Please stand by while rebooting the system...

本帖子中包含更多资源

您需要 登录 才可以下载或查看,没有账号?立即注册

×
我的恩山、我的无线 The best wifi forum is right here.
您需要登录后才可以回帖 登录 | 立即注册

本版积分规则

有疑问请添加管理员QQ86788181|手机版|小黑屋|Archiver|恩山无线论坛(常州市恩山计算机开发有限公司版权所有) ( 苏ICP备05084872号 )

GMT+8, 2024-3-29 03:00

Powered by Discuz! X3.5

© 2001-2024 Discuz! Team.

| 江苏省互联网有害信息举报中心 举报信箱:js12377 | @jischina.com.cn 举报电话:025-88802724 本站不良内容举报信箱:68610888@qq.com 举报电话:0519-86695797

快速回复 返回顶部 返回列表