找回密码
 立即注册

QQ登录

只需一步,快速开始

搜索
广告投放联系QQ68610888
查看: 2913|回复: 2

rtorrent速度上不去,大概是什么问题?

[复制链接]
发表于 2008-2-21 23:46 | 显示全部楼层 |阅读模式
ASUS WL-500GP路由刷DD-WRT V2.4 RC6.2。安装OPTWARE的Rtorrent做BT脱机下载,使用正常,就是BT速度上不去,只有20-30K,设置都是按本论坛的教程设的了,怎么搞都搞不好。以前用电脑+路由还知道做端口影射。现在直接在路由上BT了,端口影射不需要了吧?还有什么好搞的啊?????

这个是我的 rtorrent.rc文件设置:

# This is an example resource file for rTorrent. Copy to
# ~/.rtorrent.rc and enable/modify the options as needed. Remember to
# uncomment the options you wish to enable.

# Minumum amount of peers to connect per torrent, if available.
  min_peers = 40

# Minumum amount of peers to connect per torrent.
  max_peers = 250

# Same as above but for seeding completed torrents (-1 = same as downloading)
# min_peers_seed = 10
# max_peers_seed = 50

# Maximum number of simultanious uploads per torrent.
  max_uploads = 15

# Global download rate in KiB. "0" for unlimited.
  download_rate = 200

# Global upload rate in KiB. "0" for unlimited.
  upload_rate = 25

# Default directory to save downloaded files. Note it doesn't support space yet.
  directory = /mmc/share/BTdownload/Done/

# Watch a directory for new torrents, and stop those that have been deleted.
  schedule = watch_directory,5,5,load_start=/mmc/share/BTdownload/Torrent/*.torrent
# schedule = untied_directory,5,5,stop_untied=

# Close torrents when diskspace is low.
# schedule = low_diskspace,5,60,close_low_diskspace=100M

# Default session directory. Make sure you don't run multiple instance
# of rtorrent using the same session directory. Perhaps using a relative path?
  session = /mmc/share/BTdownload/session

# The ip address reported to the tracker.
# ip = 127.0.0.1
# ip = rakshasa.no

# The ip address the listening socket and outgoing connections is bound to.
# bind = 127.0.0.1
# bind = rakshasa.no

# Port range to use for listening.
  port_range = 6890-6999

# Start opening ports at a random position within the port range.
# port_random = no

# Check hash for finished torrents. Might be usefull until the bug is
# fixed that causes lack of diskspace not to be properly reported.
# check_hash = no

# Set whetever the client should try to connect to UDP trackers.
  use_udp_trackers = yes

# Alternative calls to bind and ip that should handle dynamic ip's.
# schedule = ip_tick,0,1800,ip=rakshasa
# schedule = bind_tick,0,1800,bind=rakshasa

#
# Do not modify the following parameters unless you know what you're doing.
#

# Hash read-ahead controls how many MB to request the kernel to read
# ahead. If the value is too low the disk may not be fully utilized,
# while if too high the kernel might not be able to keep the read
# pages in memory thus end up trashing.
# hash_read_ahead = 10

# Interval between attempts to check the hash, in milliseconds.
# hash_interval = 100

# Number of attempts to check the hash while using the mincore status,
# before forcing. Overworked systems might need lower values to get a
# decent hash checking rate.
# hash_max_tries = 10

# Max number of files to keep open simultaniously.
# max_open_files = 128

# Number of sockets to simultaneously keep open.
# max_open_sockets = <no default>


# Example of scheduling commands: Switch between two ip's every 5
# seconds.
# schedule = "ip_tick1,5,10,ip=torretta"
# schedule = "ip_tick2,10,10,ip=lampedusa"

# Remove a scheduled event.
# schedule_remove = "ip_tick1"

# Stop torrents when reaching upload ratio in percent,
# when also reaching total upload in bytes, or when
# reaching final upload ratio in percent.
# example: stop at ratio 2.0 with at least 200 MB uploaded, or else ratio 20.0
# schedule = ratio,60,60,"stop_on_ratio=200,200M,2000"
# schedule = ratio,30,60,stop_on_ratio=200


# Encryption options, set to none (default) or any combination of the following:
# allow_incoming, try_outgoing, require, require_RC4, enable_retry, prefer_plaintext
#
# The example value allows incoming encrypted connections, starts unencrypted
# outgoing connections but retries with encryption if they fail, preferring
# plaintext to RC4 encryption after the encrypted handshake
  encryption = allow_incoming,enable_retry,prefer_plaintext

# Enable DHT support for trackerless torrents or when all trackers are down.
# May be set to "disable" (completely disable DHT), "off" (do not start DHT),
# "auto" (start and stop DHT as needed), or "on" (start DHT immediately).
# The default is "off". For DHT to work, a session directory must be defined.
  dht = auto

# UDP port to use for DHT.
  dht_port = 7000

# Enable peer exchange (for torrents not marked private)
  peer_exchange = yes

  encoding_list = UTF-8

  scgi_port = :5000

  umask = 0777

[ 本帖最后由 mav666 于 2008-2-22 00:03 编辑 ]
我的恩山、我的无线 The best wifi forum is right here.
发表于 2008-2-22 00:14 | 显示全部楼层
还是要开端口映射,你在命令行用 iptables -t filter -L INPUT  -vn 查看一下,默认的 policy 应该是 DROP,所以非映射不可。
我的恩山、我的无线 The best wifi forum is right here.
回复

使用道具 举报

 楼主| 发表于 2008-2-22 01:38 | 显示全部楼层
开了端口影射,测试了半小时,没有好转!怎么办???
我的恩山、我的无线 The best wifi forum is right here.
回复

使用道具 举报

您需要登录后才可以回帖 登录 | 立即注册

本版积分规则

有疑问请添加管理员QQ86788181|手机版|小黑屋|Archiver|恩山无线论坛(常州市恩山计算机开发有限公司版权所有) ( 苏ICP备05084872号 )

GMT+8, 2024-3-29 04:34

Powered by Discuz! X3.5

© 2001-2024 Discuz! Team.

| 江苏省互联网有害信息举报中心 举报信箱:js12377 | @jischina.com.cn 举报电话:025-88802724 本站不良内容举报信箱:68610888@qq.com 举报电话:0519-86695797

快速回复 返回顶部 返回列表