R6300 V1刷Tomato成功

ligen119 · 发表于 2014-5-7 00:21

昨天无意在TB上淘到一块R6300 V1，到手即拆之，接上TTL线，PS：这货的TTL线有点特别，TX/RX不是连着的，中间隔了两个针；
先尝试将W1800R、D1800H 和AC66U的cfe修改（只改内存参数）后用编程器写入8pin的SPI flash，焊上，结果是W1800R和AC66U的cfe开不了机，D1800H能开机，但卡在flash信息显示，这只能说明我修改cfe的技术不到家，或者这么修改一下根本不起作用，掠过；
焊上包含原版cfe的flash（R6300 V1 cfe已经上传文件柜），开机，先刷DD，这个一次性成功，继续刷，先尝试W1800R的TT，结果变砖，不手动中断启动话则是无限循环启动，手动中断启动到cfe后，ping路由器TTL显示100时，miniweb打不开，TFTP上传不了固件，要命的是这个cfe运行help居然没有任何帮助信息出来；
万能的google派上用场了，在国外的一个坛子里面找到在cfe下执行以下命令：
flash -noheader : nflash1.trx
使用TFTP工具就可以上传固件了，（固件名必须为nflash1.trx）
完了之后运行：
go
再上传一次固件就可以刷好了；
再次回到DD界面后，直接刷入AC66U的固件（bwq版主编译），漫长等待后，启动成功，但是端口抽风，有线连接是不行的（我这个是WAN口坏了），无线连接上去，正常，修改VLAN信息，把最后一个LAN口放到WAN口中，测试PPPOE拨号，连接正常，4个LAN口一个作WAN口3个都是正常的；
目前的问题是无线只有一个，即在TT里面只能识别BCM4331的那个无线网卡，可选2.4G或5G，BCM4360的不能识别；
附贴图：

附DD和TT启动的信息，启动之前都是清除了nvram的：
DD:

Decompressing...done
CFE for R6300 version: v1.0.5
Build Date: Wed Nov 21 15:03:38 CST 2012
Init Arena
Init Devs.
Boot partition size = 262144(0x40000)
Found an ST compatible serial flash with 32 64KB blocks; total size 2MB
Found a Samsung NAND flash with 2048B pages or 128KB blocks; total size 128MB
et0: Broadcom BCM47XX 10/100/1000 Mbps Ethernet Controller 5.100.138
CPU type 0x19749: 600MHz
Tot mem: 131072 KBytes
Committing NVRAM...done
Device eth0: hwaddr 9C-D3-6D-9A-7D-B8, ipaddr 192.168.1.1, mask 255.255.255.0
gateway not set, nameserver not set
Loader:raw Filesys:tftp Dev:eth0 File:192.168.1.2:vmlinuz Options:(null)
Loading: Failed.
Could not load 192.168.1.2:vmlinuz: Timeout occured
Checking crc...Loader:raw Filesys:raw Dev:nflash0.os File: Options:(null)
Loading: ....... 4113064 bytes read
Entry at 0x80001000
Closing network.
Starting program at 0x80001000
Linux version 3.10.25 (root@localhost.localdomain) (gcc version 4.1.2) #4 Mon Apr 14 13:07:53 IST 2014
CPU revision is: 00019749 (MIPS 74Kc)
Found an ST compatible serial flash with 32 64KB blocks; total size 2MB
found nvram at 1F0000
something wrong here. do not remap
Determined physical RAM map:
memory: 07fff000 @ 00000000 (usable)
Zone ranges:
Normal [mem 0x00000000-0x07ffefff]
Movable zone start for each node
Early memory node ranges
node 0: [mem 0x00000000-0x07ffefff]
Primary instruction cache 32kB, 4-way, VIPT, I-cache aliases, linesize 32 bytes.
Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes
Built 1 zonelists in Zone order, mobility grouping on. Total pages: 32511
Kernel command line: console=ttyS0,115200 root=1f05 rootfstype=squashfs noinitrd init=/bin/sh
PID hash table entries: 512 (order: -1, 2048 bytes)
Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
Writing ErrCtl register=80000a20
Readback ErrCtl register=80000a20
Cache parity protection enabled
Memory: 125228k/131068k available (3089k kernel code, 5840k reserved, 660k data, 276k init, 0k highmem)
NR_IRQS:128
CPU: BCM5300 rev 1 at 600 MHz
bcm947xx_clockevent_set_mode: 1
bcm947xx_clockevent_set_mode: 3
console [ttyS0] enabled
Calibrating delay loop... 299.82 BogoMIPS (lpj=1499136)
pid_max: default: 32768 minimum: 301
Mount-cache hash table entries: 512
NET: Registered protocol family 16
bio: create slab <bio-0> at 0
PCI: Initializing host
PCI: Reset RC
PCI: Initializing host
PCI: Reset RC
PCI: scanning bus 0
PCI host bridge to bus 0000:00
pci_bus 0000:00: root bus resource [io 0x0000-0xffff]
pci_bus 0000:00: root bus resource [mem 0x00000000-0xffffffff]
pci_bus 0000:00: root bus resource [bus 00-ff]
PCI: Fixing up bus 0
pci 0000:00:05.0: bridge configuration invalid ([bus 00-00]), reconfiguring
pci 0000:00:06.0: bridge configuration invalid ([bus 00-00]), reconfiguring
PCI/PCIe coreunit 0 is set to bus 1.
PCI: Fixing up bridge
PCI: Fixing up bridge
PCI: Enabling device 0000:01:00.1 (0004 -> 0006)
PCI: Fixing up bus 1
PCI/PCIe coreunit 1 is set to bus 2.
PCI: Fixing up bridge
PCI: Fixing up bridge
PCI: Enabling device 0000:02:00.1 (0004 -> 0006)
PCI: Fixing up bus 2
Switching to clocksource MIPS
NET: Registered protocol family 2
TCP established hash table entries: 1024 (order: 1, 8192 bytes)
TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
TCP: Hash tables configured (established 1024 bind 1024)
TCP: reno registered
UDP hash table entries: 256 (order: 0, 4096 bytes)
UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
NET: Registered protocol family 1
R6300 GPIO Init
squashfs: version 3.0 (2006/03/15) Phillip Lougher
msgmni has been set to 244
alg: No test for stdrng (krng)
io scheduler noop registered (default)
HDLC line discipline maxframe=4096
N_HDLC line discipline registered.
Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled
serial8250: ttyS0 at MMIO 0x0 (irq = 8) is a U6_16550A
serial8250: ttyS1 at MMIO 0x0 (irq = 8) is a U6_16550A
brd: module loaded
pflash: found no supported devices
found WNDR4500 / R6300
try to find cfe size up to 2097152
no filesys. assume nflash devices
bootloader size: 2097152
nvram size: 65536
Creating 2 MTD partitions on "bcmsflash":
0x000000000000-0x000000200000 : "cfe"
0x0000001f0000-0x000000200000 : "nvram"
Found a Samsung NAND flash with 2048B pages or 128KB blocks; total size 128MB
NAND device: Manufacturer ID: 0xec, Chip ID: 0xf1 (Samsung NAND 128MiB 3,3V 8-bit), 128MiB, page size: 2048, OOB size: 64
Bad block table found at page 65472, version 0x01
Bad block table found at page 65408, version 0x01
nand_read_bbt: bad block at 0x000005000000
Creating 2 MTD partitions on "brcmnand":
0x000000000000-0x000002000000 : "linux"
0x000002000000-0x000007f00000 : "ddwrt"
lookup_nflash_rootfs_offset: offset = 0x0
found trx at 0, len =11198464
scan filesys at 178000
nflash: squash filesystem with lzma found at offset 0
Creating 2 MTD partitions on "nflash":
0x000000000000-0x000002000000 : "nandimage"
0x000000178000-0x000002000000 : "rootfs"
mtd: partition "rootfs" set to be root filesystem
add netgear bosrddata for pflash if exists
add netgear bosrddata for sflash if exists
Creating 1 MTD partitions on "bcmsflash":
0x0000001e0000-0x0000001f0000 : "board_data"
tun: Universal TUN/TAP device driver, 1.6
tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
PPP generic driver version 2.4.2
PPP BSD Compression module registered
PPP Deflate Compression module registered
PPP MPPE Compression module registered
NET: Registered protocol family 24
Broadcom Watchdog Timer: 0.07 initialized.
GACT probability NOT on
Mirror/redirect action on
Failed to load ipt action
Simple TC action Loaded
netem: version 1.3
u32 classifier
Performance counters on
input device check on
Actions configured
Netfilter messages via NETLINK v0.30.
nf_conntrack version 0.5.0 (1956 buckets, 7824 max)
nf_conntrack_rtsp v0.6.21 loading
xt_time: kernel timezone is -0000
ip_set: protocol 6
gre: GRE over IPv4 demultiplexor driver
nf_nat_rtsp v0.6.21 loading
ip_tables: (C) 2000-2006 Netfilter Core Team
TCP: bic registered
TCP: cubic registered
TCP: westwood registered
TCP: highspeed registered
TCP: hybla registered
TCP: htcp registered
TCP: vegas registered
TCP: veno registered
TCP: scalable registered
TCP: lp registered
TCP: yeah registered
TCP: illinois registered
NET: Registered protocol family 17
Bridge firewalling registered
8021q: 802.1Q VLAN Support v1.8
startup nvram driver
found nvram
VFS: Mounted root (squashfs filesystem) readonly on device 31:5.
Freeing unused kernel memory: 276K (803ab000 - 803f0000)
start service
starting Architecture code for broadcom
starting hotplug
Jan 1 00:00:03 udevtrigger[752]: parse_config_file: can't open '/etc/udev/udev.conf' as config file: No such file or directory
done
boardnum 4536
boardtype 0xf52e
boardrev 0x1102
Booting device: Netgear R6300
get_wl_instance doesnt return the right value 0
eth1: No such device
loading et
et: module license 'Proprietary' taints kernel.
Disabling lock debugging due to kernel taint
et_module_init: passivemode set to 0x0
et_module_init: txworkq set to 0x0
et_module_init: et_txq_thresh set to 0x400
bcm_robo_enable_switch: EEE is disabled
et0: online cpus 1
eth0: Broadcom BCM47XX 10/100/1000 Mbps Ethernet Controller 6.37.14.62 (r437318)
loading switch-core
loading switch-robo
roboswitch: Probing device 'eth0'
roboswitch: trying a 53125! at eth0
roboswitch: found a 53125! at eth0
PCI: Enabling device 0000:01:01.0 (0000 -> 0002)
PCI: Enabling device 0000:02:01.0 (0000 -> 0002)
[USB] checking...
umount: can't umount /mnt: No such file or directory
rmmod: usblp: No such file or directory
rmmod: printer: No such file or directory
rmmod: usb-storage: No such file or directory
rmmod: sr_mod: No such file or directory
rmmod: cdrom: No such file or directory
rmmod: sd_mod: No such file or directory
rmmod: scsi_wait_scan: No such file or directory
rmmod: scsi_mod: No such file or directory
rmmod: usbmisc_imx: No such file or directory
rmmod: ci13xxx_imx: No such file or directory
rmmod: ci_hdrc: No such file or directory
rmmod: phy-mxs-usb: No such file or directory
rmmod: fsl-mph-dr-of: No such file or directory
rmmod: usb-libusual: No such file or directory
rmmod: dwc_otg: No such file or directory
rmmod: xhci-hcd: No such file or directory
rmmod: usb-ohci: No such file or directory
rmmod: ohci-hcd: No such file or directory
rmmod: uhci-hcd: No such file or directory
rmmod: usb-uhci: No such file or directory
rmmod: ehci-pci: No such file or directory
rmmod: ehci-platform: No such file or directory
rmmod: ehci-hcd: No such file or directory
rmmod: fsl-mph-dr-of: No such file or directory
rmmod: usbcore: No such file or directory
rmmod: usb-common: No such file or directory
rmmod: xfs: No such file or directory
rmmod: msdos: No such file or directory
rmmod: vfat: No such file or directory
rmmod: fat: No such file or directory
rmmod: nls_utf8: No such file or directory
rmmod: nls_iso8859-2: No such file or directory
rmmod: nls_iso8859-1: No such file or directory
rmmod: nls_cp437: No such file or directory
rmmod: nls_cp932: No such file or directory
rmmod: nls_cp936: No such file or directory
rmmod: nls_cp950: No such file or directory
rmmod: nls_base: No such file or directory
rmmod: ext3: No such file or directory
rmmod: jbd: No such file or directory
rmmod: ext2: No such file or directory
rmmod: mbcache: No such file or directory
rmmod: fuse: No such file or directory
/etc/preinit: line 66: can't create /proc/sys/net/ipv4/ip_conntrack_max: nonexistent directory
/etc/preinit: line 66: can't create /proc/sys/net/ipv4/ip_conntrack_max: nonexistent directory
set port 4 to AUTO
set port 0 to AUTO
set port 1 to AUTO
set port 2 to AUTO
set port 3 to AUTO
vconfig: ioctl error for add: File exists
vconfig: ioctl error for add: File exists
configure vlan ports to
configure vlan ports to 1 2 3 8*
configure vlan ports to 4 0 8*
configure vlan ports to
configure vlan ports to
configure vlan ports to
configure vlan ports to
configure vlan ports to
configure vlan ports to
configure vlan ports to
configure vlan ports to
configure vlan ports to
configure vlan ports to
configure vlan ports to
configure vlan ports to
configure vlan ports to
eth1: Operation not supported
wl0.1: No such device
wl0.2: No such device
wl0.3: No such device
eth1: Operation not permitted
nbw = 20
channel 6, val 20
0, 1000, 0, 6
spec 1006
eth1: Argument list too long
eth1: Operation not supported
eth1: Operation not supported
eth1: Operation not supported
eth1: Operation not supported
eth1: Operation not supported
eth1: Operation not supported
eth1: Operation not supported
eth1: Operation not supported
eth1: Operation not supported
eth1: Operation not supported
eth1: Operation not supported
eth1: Operation not supported
eth1: Operation not supported
eth1: Operation not supported
eth1: Operation not supported
eth1: Operation not supported
eth1: Operation not supported
eth1: Operation not supported
eth1: Operation not supported
eth1: Operation not supported
eth1: Operation not supported
eth1: Operation not supported
eth1: Operation not supported
eth1: Operation not supported
eth1: Operation not supported
eth1: Operation not supported
eth1: Operation not supported
eth1: Operation not supported
eth1: Operation not supported
eth1: Operation not supported
eth1: Operation not supported
wl: Unsupported
wl: Not down
eth2: Operation not supported
wl1.1: No such device
wl1.2: No such device
wl1.3: No such device
eth2: Operation not permitted
eth2: Operation not supported
eth2: Operation not supported
eth2: Operation not supported
eth2: Operation not supported
eth2: Operation not supported
eth2: Operation not supported
eth2: Operation not supported
eth2: Operation not supported
eth2: Operation not supported
eth2: Operation not supported
eth2: Operation not supported
eth2: Operation not supported
eth2: Operation not supported
eth2: Operation not supported
eth2: Operation not supported
eth2: Operation not supported
eth2: Operation not supported
eth2: Operation not supported
eth2: Operation not supported
eth2: Operation not supported
eth2: Operation not supported
eth2: Operation not supported
eth2: Operation not supported
eth2: Operation not supported
eth2: Operation not supported
eth2: Operation not supported
eth2: Operation not supported
eth2: Operation not supported
eth2: Operation not supported
eth2: Operation not supported
eth2: Operation not supported
wl: Unsupported
route: ioctl 0x890c failed: No such process
route: ioctl 0x890b failed: Network is unreachable
device br0 entered promiscuous mode
br0: Invalid argument
wl: Not down
eth2: Operation not supported
wl1.1: No such device
wl1.2: No such device
wl1.3: No such device
eth2: Operation not permitted
eth2: Invalid argument
eth2: Operation not supported
eth2: Operation not supported
eth2: Operation not supported
eth2: Operation not supported
eth2: Operation not supported
eth2: Operation not supported
eth2: Operation not supported
eth2: Operation not supported
eth2: Operation not supported
eth2: Operation not supported
eth2: Operation not supported
eth2: Operation not supported
eth2: Operation not supported
eth2: Operation not supported
eth2: Operation not supported
eth2: Operation not supported
eth2: Operation not supported
eth2: Operation not supported
eth2: Operation not supported
eth2: Operation not supported
eth2: Operation not supported
eth2: Operation not supported
eth2: Operation not supported
eth2: Operation not supported
eth2: Operation not supported
eth2: Operation not supported
eth2: Operation not supported
eth2: Operation not supported
eth2: Operation not supported
eth2: Operation not supported
eth2: Operation not supported
wl: Unsupported
device eth2 entered promiscuous mode
br0: Invalid argument
device vlan1 entered promiscuous mode
device eth0 entered promiscuous mode
eth1: Operation not supported
wl0.1: No such device
wl0.2: No such device
wl0.3: No such device
eth1: Operation not permitted
eth1: Invalid argument
nbw = 20
channel 6, val 20
0, 1000, 0, 6
spec 1006
eth1: Argument list too long
eth1: Operation not supported
eth1: Operation not supported
eth1: Operation not supported
eth1: Operation not supported
eth1: Operation not supported
eth1: Operation not supported
eth1: Operation not supported
eth1: Operation not supported
eth1: Operation not supported
eth1: Operation not supported
eth1: Operation not supported
eth1: Operation not supported
eth1: Operation not supported
eth1: Operation not supported
eth1: Operation not supported
eth1: Operation not supported
eth1: Operation not supported
eth1: Operation not supported
eth1: Operation not supported
eth1: Operation not supported
eth1: Operation not supported
eth1: Operation not supported
eth1: Operation not supported
eth1: Operation not supported
eth1: Operation not supported
eth1: Operation not supported
eth1: Operation not supported
eth1: Operation not supported
eth1: Operation not supported
eth1: Operation not supported
eth1: Operation not supported
wl: Unsupported
device eth1 entered promiscuous mode
br0: port 3(eth1) entered forwarding state
br0: port 3(eth1) entered forwarding state
br0: port 2(vlan1) entered forwarding state
br0: port 2(vlan1) entered forwarding state
br0: port 1(eth2) entered forwarding state
br0: port 1(eth2) entered forwarding state
device br0 left promiscuous mode
device br0 entered promiscuous mode
ifconfig: ioctl 0x8914 failed: Cannot assign requested address
device br0 left promiscuous mode
route: ioctl 0x890c failed: No such process
route: ioctl 0x890b failed: Network is unreachable
function start_hwmon not found
cp: can't stat '/tmp/mycron.d/*': No such file or directory
cp: can't stat '/jffs/mycron.d/*': No such file or directory
cp: can't stat '/mmc/mycron.d/*': No such file or directory
route: ioctl 0x890c failed: No such process
route: ioctl 0x890b failed: Network is unreachable
rmmod: n_hdlc: No such file or directory
device vlan2 entered promiscuous mode
device vlan2 left promiscuous mode
udhcpc (v1.21.1) started
Sending discover...
SIOCGIFFLAGS: No such device
br0: port 3(eth1) entered forwarding state
br0: port 2(vlan1) entered forwarding state
br0: port 1(eth2) entered forwarding state
/bin/sh: /opt/etc/init.d/rcS: not found
/bin/sh: /jffs/etc/init.d/rcS: not found
/bin/sh: /mmc/etc/init.d/rcS: not found
sh: missing ]
rmmod: ipt_webstr: No such file or directory
rmmod: ipt_layer7: No such file or directory
rmmod: xt_layer7: No such file or directory
rmmod: ipt_ipp2p: No such file or directory
rmmod: xt_ipp2p: No such file or directory
killall: proxywatchdog.sh: no process killed
killall: schedulerb.sh: no process killed
rmmod: xt_physdev: No such file or directory
rmmod: xt_IMQ: No such file or directory
rmmod: ipt_IMQ: No such file or directory
rmmod: imq: No such file or directory
killall: wdswatchdog.sh: no process killed
rmmod: sch_codel: No such file or directory
rmmod: sch_fq_codel: No such file or directory
Sending discover...
Sending discover...
Sending discover...
Sending discover...
Sending discover...
DD-WRT v24-sp2 giga (c) 2013 NewMedia-NET GmbH
Release: 04/14/14 (SVN revision: build r23075)

复制代码

TT：

Decompressing...done
CFE for R6300 version: v1.0.5
Build Date: Wed Nov 21 15:03:38 CST 2012
Init Arena
Init Devs.
Boot partition size = 262144(0x40000)
Found an ST compatible serial flash with 32 64KB blocks; total size 2MB
Found a Samsung NAND flash with 2048B pages or 128KB blocks; total size 128MB
et0: Broadcom BCM47XX 10/100/1000 Mbps Ethernet Controller 5.100.138
CPU type 0x19749: 600MHz
Tot mem: 131072 KBytes
Committing NVRAM...done
Waiting for reset button release...don?ecompressing...done
CFE for R6300 version: v1.0.5
Build Date: Wed Nov 21 15:03:38 CST 2012
Init Arena
Init Devs.
Boot partition size = 262144(0x40000)
Found an ST compatible serial flash with 32 64KB blocks; total size 2MB
Found a Samsung NAND flash with 2048B pages or 128KB blocks; total size 128MB
et0: Broadcom BCM47XX 10/100/1000 Mbps Ethernet Controller 5.100.138
CPU type 0x19749: 600MHz
Tot mem: 131072 KBytes
Device eth0: hwaddr 9C-D3-6D-9A-7D-B8, ipaddr 192.168.1.1, mask 255.255.255.0
gateway not set, nameserver not set
Checking crc...Loader:raw Filesys:raw Dev:nflash0.os File: Options:(null)
Loading: ...... 3396264 bytes read
Entry at 0x80001000
Closing network.
Starting program at 0x80001000
Linux version 2.6.22.19 (root@asus) (gcc version 4.2.4) #2 Sat Nov 30 08:29:54 CET 2013
CPU revision is: 00019749
Found an ST compatible serial flash with 32 64KB blocks; total size 2MB
Determined physical RAM map:
memory: 07fff000 @ 00000000 (usable)
Zone PFN ranges:
Normal 0 -> 32767
HighMem 32767 -> 32767
early_node_map[1] active PFN ranges
0: 0 -> 32767
Built 1 zonelists. Total pages: 32767
Kernel command line: root=/dev/mtdblock3 console=ttyS0,115200 init=/sbin/preinit
Primary instruction cache 32kB, physically tagged, 4-way, linesize 32 bytes.
Primary data cache 32kB, 4-way, linesize 32 bytes.
Synthesized TLB refill handler (20 instructions).
Synthesized TLB load handler fastpath (32 instructions).
Synthesized TLB store handler fastpath (32 instructions).
Synthesized TLB modify handler fastpath (31 instructions).
PID hash table entries: 512 (order: 9, 2048 bytes)
CPU: BCM5300 rev 1 pkg 0 at 600 MHz
Using 300.000 MHz high precision timer.
console [ttyS0] enabled
Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
Memory: 125908k/131068k available (2704k kernel code, 5008k reserved, 404k data, 208k init, 0k highmem)
Mount-cache hash table entries: 512
NET: Registered protocol family 16
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
PCI: Initializing host
PCI: Reset RC
PCI: Initializing host
PCI: Reset RC
PCI: Fixing up bus 0
PCI/PCIe coreunit 0 is set to bus 1.
PCI: Fixing up bridge
PCI: Fixing up bridge
PCI: Enabling device 0000:01:00.1 (0004 -> 0006)
PCI: Fixing up bus 1
PCI/PCIe coreunit 1 is set to bus 2.
PCI: Fixing up bridge
PCI: Fixing up bridge
PCI: Enabling device 0000:02:00.1 (0004 -> 0006)
PCI: Fixing up bus 2
NET: Registered protocol family 2
Time: MIPS clocksource has been installed.
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
TCP established hash table entries: 4096 (order: 3, 32768 bytes)
TCP bind hash table entries: 4096 (order: 2, 16384 bytes)
TCP: Hash tables configured (established 4096 bind 4096)
TCP reno registered
squashfs: version 3.2-r2 (2007/01/15) Phillip Lougher
io scheduler noop registered (default)
HDLC line discipline: version $Revision: 4.8 $, maxframe=4096
N_HDLC line discipline registered.
Serial: 8250/16550 driver $Revision: 1.90 $ 2 ports, IRQ sharing disabled
serial8250: ttyS0 at MMIO 0x0 (irq = 8) is a 16550A
serial8250: ttyS1 at MMIO 0x0 (irq = 8) is a 16550A
PPP generic driver version 2.4.2
MPPE/MPPC encryption/compression module registered
NET: Registered protocol family 24
PPPoL2TP kernel driver, V0.18.3
PPTP driver version 0.8.5
pflash: found no supported devices
Boot partition size = 262144(0x40000)
Creating 2 MTD partitions on "sflash":
0x00000000-0x00040000 : "pmon"
0x001f0000-0x00200000 : "nvram"
Found a Samsung NAND flash with 2048B pages or 128KB blocks; total size 128MB
lookup_nflash_rootfs_offset: offset = 0x0
nflash: squash filesystem with lzma found at block 9
Creating 2 MTD partitions on "nflash":
0x00000000-0x02000000 : "linux"
0x001339c8-0x02000000 : "rootfs"
NAND device: Manufacturer ID: 0xec, Chip ID: 0xf1 (Samsung NAND 128MiB 3,3V 8-bit)
Creating 3 MTD partitions on "brcmnand":
0x00000000-0x02000000 : "trx"
0x02000000-0x04000000 : "jffs2"
0x04000000-0x07f00000 : "brcmnand"
dev_nvram_init: _nvram_init
_nvram_init: allocat size= 65536
usbcore: registered new interface driver hiddev
usbcore: registered new interface driver usbhid
drivers/hid/usbhid/hid-core.c: v2.6:USB HID core driver
u32 classifier
OLD policer on
Netfilter messages via NETLINK v0.30.
nf_conntrack version 0.5.0 (1024 buckets, 8192 max)
ip_tables: (C) 2000-2006 Netfilter Core Team
ipt_account 0.1.21 : Piotr Gasidlo <quaker@barbara.eu.org>, http://www.barbara.eu.org/~quaker/ipt_account/
net/ipv4/netfilter/tomato_ct.c [Nov 30 2013 08:10:30]
NET: Registered protocol family 1
NET: Registered protocol family 10
ip6_tables: (C) 2000-2006 Netfilter Core Team
NET: Registered protocol family 17
802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>
All bugs added by David S. Miller <davem@redhat.com>
VFS: Mounted root (squashfs filesystem) readonly.
Freeing unused kernel memory: 208k freed
Warning: unable to open an initial console.
Failed to execute /sbin/preinit. Attempting defaults...
Restarting system.
Please stand by while rebooting the system...
Decompressing...done
CFE for R6300 version: v1.0.5
Build Date: Wed Nov 21 15:03:38 CST 2012
Init Arena
Init Devs.
Boot partition size = 262144(0x40000)
Found an ST compatible serial flash with 32 64KB blocks; total size 2MB
Found a Samsung NAND flash with 2048B pages or 128KB blocks; total size 128MB
et0: Broadcom BCM47XX 10/100/1000 Mbps Ethernet Controller 5.100.138
CPU type 0x19749: 600MHz
Tot mem: 131072 KBytes
Device eth0: hwaddr 9C-D3-6D-9A-7D-B8, ipaddr 192.168.1.1, mask 255.255.255.0
gateway not set, nameserver not set
Checking crc...Loader:raw Filesys:raw Dev:nflash0.os File: Options:(null)
Loading: ...... 3396264 bytes read
Entry at 0x80001000
Closing network.
Starting program at 0x80001000
Linux version 2.6.22.19 (root@asus) (gcc version 4.2.4) #2 Sat Nov 30 08:29:54 CET 2013
CPU revision is: 00019749
Found an ST compatible serial flash with 32 64KB blocks; total size 2MB
Determined physical RAM map:
memory: 07fff000 @ 00000000 (usable)
Zone PFN ranges:
Normal 0 -> 32767
HighMem 32767 -> 32767
early_node_map[1] active PFN ranges
0: 0 -> 32767
Built 1 zonelists. Total pages: 32767
Kernel command line: root=/dev/mtdblock3 console=ttyS0,115200 init=/sbin/preinit
Primary instruction cache 32kB, physically tagged, 4-way, linesize 32 bytes.
Primary data cache 32kB, 4-way, linesize 32 bytes.
Synthesized TLB refill handler (20 instructions).
Synthesized TLB load handler fastpath (32 instructions).
Synthesized TLB store handler fastpath (32 instructions).
Synthesized TLB modify handler fastpath (31 instructions).
PID hash table entries: 512 (order: 9, 2048 bytes)
CPU: BCM5300 rev 1 pkg 0 at 600 MHz
Using 300.000 MHz high precision timer.
console [ttyS0] enabled
Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
Memory: 125908k/131068k available (2704k kernel code, 5008k reserved, 404k data, 208k init, 0k highmem)
Mount-cache hash table entries: 512
NET: Registered protocol family 16
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
PCI: Initializing host
PCI: Reset RC
PCI: Initializing host
PCI: Reset RC
PCI: Fixing up bus 0
PCI/PCIe coreunit 0 is set to bus 1.
PCI: Fixing up bridge
PCI: Fixing up bridge
PCI: Enabling device 0000:01:00.1 (0004 -> 0006)
PCI: Fixing up bus 1
PCI/PCIe coreunit 1 is set to bus 2.
PCI: Fixing up bridge
PCI: Fixing up bridge
PCI: Enabling device 0000:02:00.1 (0004 -> 0006)
PCI: Fixing up bus 2
NET: Registered protocol family 2
Time: MIPS clocksource has been installed.
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
TCP established hash table entries: 4096 (order: 3, 32768 bytes)
TCP bind hash table entries: 4096 (order: 2, 16384 bytes)
TCP: Hash tables configured (established 4096 bind 4096)
TCP reno registered
squashfs: version 3.2-r2 (2007/01/15) Phillip Lougher
io scheduler noop registered (default)
HDLC line discipline: version $Revision: 4.8 $, maxframe=4096
N_HDLC line discipline registered.
Serial: 8250/16550 driver $Revision: 1.90 $ 2 ports, IRQ sharing disabled
?ial8250: ttyS0 at MMIO 0x0 (irq = 8) is a 16550A
serial8250: ttyS1 at MMIO 0x0 (irq = 8) is a 16550A
PPP generic driver version 2.4.2
MPPE/MPPC encryption/compression module registered
NET: Registered protocol family 24
PPPoL2TP kernel driver, V0.18.3
PPTP driver version 0.8.5
pflash: found no supported devices
Boot partition size = 262144(0x40000)
Creating 2 MTD partitions on "sflash":
0x00000000-0x00040000 : "pmon"
0x001f0000-0x00200000 : "nvram"
Found a Samsung NAND flash with 2048B pages or 128KB blocks; total size 128MB
lookup_nflash_rootfs_offset: offset = 0x0
nflash: squash filesystem with lzma found at block 9
Creating 2 MTD partitions on "nflash":
0x00000000-0x02000000 : "linux"
0x001339c8-0x02000000 : "rootfs"
NAND device: Manufacturer ID: 0xec, Chip ID: 0xf1 (Samsung NAND 128MiB 3,3V 8-bit)
Creating 3 MTD partitions on "brcmnand":
0x00000000-0x02000000 : "trx"
0x02000000-0x04000000 : "jffs2"
0x04000000-0x07f00000 : "brcmnand"
dev_nvram_init: _nvram_init
_nvram_init: allocat size= 65536
usbcore: registered new interface driver hiddev
usbcore: registered new interface driver usbhid
drivers/hid/usbhid/hid-core.c: v2.6:USB HID core driver
u32 classifier
OLD policer on
Netfilter messages via NETLINK v0.30.
nf_conntrack version 0.5.0 (1024 buckets, 8192 max)
ip_tables: (C) 2000-2006 Netfilter Core Team
ipt_account 0.1.21 : Piotr Gasidlo <quaker@barbara.eu.org>, http://www.barbara.eu.org/~quaker/ipt_account/
net/ipv4/netfilter/tomato_ct.c [Nov 30 2013 08:10:30]
NET: Registered protocol family 1
NET: Registered protocol family 10
ip6_tables: (C) 2000-2006 Netfilter Core Team
NET: Registered protocol family 17
802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>
All bugs added by David S. Miller <davem@redhat.com>
VFS: Mounted root (squashfs filesystem) readonly.
Freeing unused kernel memory: 208k freed
Warning: unable to open an initial console.
Failed to execute /sbin/preinit. Attempting defaults...
emf: module license 'Proprietary' taints kernel.
et_module_init: passivemode set to 0x0
et_module_init: et_txq_thresh set to 0x0
bcm_robo_enable_switch: EEE is disabled
eth0: Broadcom BCM47XX 10/100/1000 Mbps Ethernet Controller 6.30.39.31 (r341183)
PCI: Enabling device 0000:01:01.0 (0000 -> 0002)
eth1: Broadcom BCM4331 802.11 Wireless Controller 6.30.102.9 (r366174)
PCI: Enabling device 0000:02:01.0 (0000 -> 0002)
wl driver 6.30.102.9 (r366174) failed with code 21
/ # vlan0: No such device
eth2: No such device
eth3: No such device
lo: File exists
/ #

复制代码

期待版主下个更新已经包含R6300 V1的TT固件

housecall · 发表于 2014-5-7 06:53

我只能默默的说：。。。。。。你太牛了

bigsun · 发表于 2014-5-8 11:09

牛这也能刷上

ligen119 · 发表于 2014-5-9 10:38

试用两天，发现这货的无线很蛋疼，隔一堵墙就不行了，比W1800R差的不是一点；
想想还是刷回DD吧！

J.King · 发表于 2014-5-9 22:37

AC66U的cfe是什么版本？求一个。

bwq518 · 发表于 2014-5-14 17:02

可以考虑支持，你的CFE呢？方便发给我吗？ bwq518@gmail.com

zjzrc · 发表于 2014-5-14 17:11

楼主土豪啊，600+

ligen119 · 发表于 2014-5-14 22:21

bwq518 发表于 2014-5-14 17:02
可以考虑支持，你的CFE呢？方便发给我吗？

https://www.right.com.cn/forum/thread-141547-1-1.html
这个帖子里面包含有！

bwq518 · 发表于 2014-5-15 00:47

ligen119 发表于 2014-5-14 22:21
https://www.right.com.cn/forum/thread-141547-1-1.html
这个帖子里面包含有！

能否把你手工修改好的vlan1 vlan2的参数贴上来？

nvram find vlan

bb06412000 · 发表于 2014-6-25 10:21

能否请楼主给我看看我的路由器，用nvram erase命令不能够清除nvram

Decompressing...done

CFE for R6300 version: v1.0.2
Build Date: Wed Apr 25 16:29:10 CST 2012
Init Arena
Init Devs.
Boot partition size = 262144(0x40000)
Found an ST compatible serial flash with 32 64KB blocks; total size 2MB
Found a Samsung NAND flash with 2048B pages or 128KB blocks; total size 128MB
et0: Broadcom BCM47XX 10/100/1000 Mbps Ethernet Controller 5.100.138
CPU type 0x19749: 600MHz
Tot mem: 131072 KBytes

Device eth0:  hwaddr 84-1B-5E-D2-97-AE, ipaddr 192.168.1.1, mask 255.255.255.0
      gateway not set, nameserver not set
Checking crc...Boot program checksum is invalid
Device eth0 has been deactivated.
Device eth0:  hwaddr 84-1B-5E-D2-97-AE, ipaddr 192.168.1.1, mask 255.255.255.0
      gateway not set, nameserver not set
Start TFTP server
Reading ::

用nvram erase时显示

Decompressing...done

CFE for R6300 version: v1.0.2
Build Date: Wed Apr 25 16:29:10 CST 2012
Init Arena
Init Devs.
Boot partition size = 262144(0x40000)
Found an ST compatible serial flash with 32 64KB blocks; total size 2MB
Found a Samsung NAND flash with 2048B pages or 128KB blocks; total size 128MB
et0: Broadcom BCM47XX 10/100/1000 Mbps Ethernet Controller 5.100.138
CPU type 0x19749: 600MHz
Tot mem: 131072 KBytes

Device eth0:  hwaddr 84-1B-5E-D2-97-AE, ipaddr 192.168.1.1, mask 255.255.255.0
      gateway not set, nameserver not set
Startup canceled
CFE> ^C
CFE> nvram erase
*** command status = 0

shardineblog · 发表于 2016-9-1 09:59

恭喜。。。。

账号		自动登录	找回密码
密码			立即注册

R6300 V1刷Tomato成功

本帖子中包含更多资源

相关帖子