找回密码
 立即注册

QQ登录

只需一步,快速开始

搜索
广告投放联系QQ68610888
查看: 6557|回复: 6

关于盛鑫源与222ba 1800机器无法刷入TT的调查结果 判定为机器正常

[复制链接]
发表于 2014-7-28 18:06 | 显示全部楼层 |阅读模式
本帖最后由 antons 于 2014-7-28 18:12 编辑

根据坛友盛鑫源与222ba的争论点,今日已收到机器,并第一时间进行了测试,机器测试正常,目前已成功刷入BWQ518 120版TT固件,可以稳定运行
结论为222ba所售机器无问题,机器故障为刷机导致的NVRAM损坏,清空NVRAM并重刷CFE后故障解决


收到测试机后,初始状态为DD固件,无硬件改动,硬件无损坏,
第一次刷入TT固件,测试失败,根据状态出错提示,为NVRAM损坏,一般为非正常刷机或者设置造成
逐重新刷入备份CFE并TTL清空NVRAM 重新TFTP刷机

注意,清空NVRAM后,机器可能数次(3~5次)重启后才能正常进入系统,进入系统后,建议界面上重新恢复一次设置,











TTL信息


BUFFALO CFE Version 1.04
Memory Test start(0xA0100000) end(0xA8000000) size(33292288)
Data line test start:0xa0100000 pattern 0x00000001 0x00000003 0x00000007 0x0000000F 0x00000005 0x00000015 0x00000055 0xAAAAAAAA
Address line test start:0xa0100000 len:0x7f00000 pattern 0xAAAAAAAA 0x55555555  
Fill test patnum:2
fill Pattern 5555AAAA  Writing...   Reading...
fill Pattern AAAA5555  Writing...   Reading...
Decompressing...done


CFE version 6.30.15.3 (r315282) based on BBP 1.0.37 for BCM947XX (32bit,SP,LE)
Build Date: Tue Apr 24 09:04:01 JST 2012 (root@fc15.localdomain)
Copyright (C) 2000-2008 Broadcom Corporation.

Init Arena
Initializing PCI. [normal]
PCI bus 0 slot 0/0: vendor 0x14e4 product 0x0800 (flash memory, rev 0x01)
PCI bus 0 slot 1/0: vendor 0x14e4 product 0x4715 (ethernet network, rev 0x01)
PCI bus 0 slot 4/0: vendor 0x14e4 product 0x471a (USB serial bus, interface 0x10, rev 0x01)
PCI bus 0 slot 4/1: vendor 0x14e4 product 0x471a (USB serial bus, interface 0x20, rev 0x01)
PCI bus 0 slot 5/0: vendor 0x14e4 product 0x0820 (PCI bridge, rev 0x01)
PCI bus 0 slot 6/0: vendor 0x14e4 product 0x0820 (PCI bridge, rev 0x01)
PCI bus 0 slot 7/0: vendor 0x14e4 product 0x052e (undefined subclass 0xff, interface 0xff, rev 0x01)
PCI bus 0 slot 8/0: vendor 0x14e4 product 0x080e (RAM memory, rev 0x01)
PCI bus 0 slot 9/0: vendor 0x14e4 product 0x0534 (undefined subclass 0xff, interface 0xff, rev 0x01)
Init Devs.
Boot partition size = 262144(0x40000)
Found an ST compatible serial flash with 32 64KB blocks; total size 2MB
Found a Samsung (1 bit-cell) NAND flash with 2048B pages or 128KB blocks; total size 128MB
bcm_robo_enable_switch: EEE is disabled
et0: Broadcom BCM47XX 10/100/1000 Mbps Ethernet Controller 6.30.15.3 (r315282)
CPU type 0x19749: 600MHz
Tot mem: 131072 KBytes

CFE mem:    0x87000000 - 0x87164A60 (1460832)
Data:       0x8704C9A0 - 0x87050BA0 (16896)
BSS:        0x87050BA0 - 0x87062A60 (73408)
Heap:       0x87062A60 - 0x87162A60 (1048576)
Stack:      0x87162A60 - 0x87164A60 (8192)
Text:       0x87000000 - 0x8704C994 (313748)

DRAM magic offset:001E0000 size:00010000
DRAM magic found
Device eth0:  hwaddr 12-6F-3F-81-43-2F, ipaddr 192.168.11.1, mask 255.255.255.0
        gateway not set, nameserver not set
check_trx: start nflash1.trx
check_trx: exit nflash1.trx
Loader:raw Filesys:raw Dev:nflash0.os File: Optionsnull)
Loading: .. 3191392 bytes read
Entry at 0x80001000
Closing network.
Starting program at 0x80001000
Linux version 2.6.22.19 (root@asus) (gcc version 4.2.4) #13 Wed Jun 25 06:39:11 CST 2014
CPU revision is: 00019749
Found an ST compatible serial flash with 32 64KB blocks; total size 2MB
Determined physical RAM map:
memory: 07fff000 @ 00000000 (usable)
Zone PFN ranges:
  Normal          0 ->    32767
  HighMem     32767 ->    32767
early_node_map[1] active PFN ranges
    0:        0 ->    32767
Built 1 zonelists.  Total pages: 32767
Kernel command line: root=/dev/mtdblock3 console=ttyS0,115200 init=/sbin/preinit
Primary instruction cache 32kB, physically tagged, 4-way, linesize 32 bytes.
Primary data cache 32kB, 4-way, linesize 32 bytes.
Synthesized TLB refill handler (20 instructions).
Synthesized TLB load handler fastpath (32 instructions).
Synthesized TLB store handler fastpath (32 instructions).
Synthesized TLB modify handler fastpath (31 instructions).
PID hash table entries: 512 (order: 9, 2048 bytes)
CPU: BCM5300 rev 1 pkg 0 at 600 MHz
Using 300.000 MHz high precision timer.
console [ttyS0] enabled
Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
Memory: 126108k/131068k available (2518k kernel code, 4808k reserved, 397k data, 200k init, 0k highmem)
Mount-cache hash table entries: 512
NET: Registered protocol family 16
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
PCI: Initializing host
PCI: Reset RC
PCI: Initializing host
PCI: Reset RC
PCI: Fixing up bus 0
PCI/PCIe coreunit 0 is set to bus 1.
PCI: Fixing up bridge
PCI: Fixing up bridge
PCI: Enabling device 0000:01:00.1 (0004 -> 0006)
PCI: Fixing up bus 1
PCI/PCIe coreunit 1 is set to bus 2.
PCI: Fixing up bridge
PCI: Fixing up bridge
PCI: Enabling device 0000:02:00.1 (0004 -> 0006)
PCI: Fixing up bus 2
NET: Registered protocol family 2
Time: MIPS clocksource has been installed.
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
TCP established hash table entries: 4096 (order: 3, 32768 bytes)
TCP bind hash table entries: 4096 (order: 2, 16384 bytes)
TCP: Hash tables configured (established 4096 bind 4096)
TCP reno registered
squashfs: version 3.2-r2 (2007/01/15) Phillip Lougher
io scheduler noop registered (default)
HDLC line discipline: version $Revision: 4.8 $, maxframe=4096
N_HDLC line discipline registered.
Serial: 8250/16550 driver $Revision: 1.90 $ 2 ports, IRQ sharing disabled
serial8250: ttyS0 at MMIO 0x0 (irq = 8) is a 16550A
serial8250: ttyS1 at MMIO 0x0 (irq = 8) is a 16550A
PPP generic driver version 2.4.2
MPPE/MPPC encryption/compression module registered
NET: Registered protocol family 24
PPPoL2TP kernel driver, V0.18.3
PPTP driver version 0.8.5
pflash: found no supported devices
Boot partition size = 262144(0x40000)
Creating 2 MTD partitions on "sflash":
0x00000000-0x00040000 : "pmon"
0x001f0000-0x00200000 : "nvram"
Found a Samsung NAND flash with 2048B pages or 128KB blocks; total size 128MB
lookup_nflash_rootfs_offset: offset = 0x0
nflash: squash filesystem with lzma found at block 8
Creating 2 MTD partitions on "nflash":
0x00000000-0x02000000 : "linux"
0x00118c44-0x02000000 : "rootfs"
NAND device: Manufacturer ID: 0xec, Chip ID: 0xf1 (Samsung NAND 128MiB 3,3V 8-bit)
Creating 3 MTD partitions on "brcmnand":
0x00000000-0x02000000 : "trx"
0x02000000-0x04000000 : "jffs2"
0x04000000-0x07f00000 : "brcmnand"
dev_nvram_init: _nvram_init
_nvram_init: allocat size= 65536
usbcore: registered new interface driver hiddev
usbcore: registered new interface driver usbhid
drivers/hid/usbhid/hid-core.c: v2.6:USB HID core driver
u32 classifier
    OLD policer on
Netfilter messages via NETLINK v0.30.
nf_conntrack version 0.5.0 (1024 buckets, 8192 max)
ip_tables: (C) 2000-2006 Netfilter Core Team
ipt_account 0.1.21 : Piotr Gasidlo <quaker@barbara.eu.org>, http://www.barbara.eu.org/~quaker/ipt_account/
net/ipv4/netfilter/tomato_ct.c [Jun 25 2014 06:11:43]
NET: Registered protocol family 1
NET: Registered protocol family 10
ip6_tables: (C) 2000-2006 Netfilter Core Team
NET: Registered protocol family 17
802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>
All bugs added by David S. Miller <davem@redhat.com>
VFS: Mounted root (squashfs filesystem) readonly.
Freeing unused kernel memory: 200k freed
Warning: unable to open an initial console.
Failed to execute /sbin/preinit.  Attempting defaults...
Restarting system.
Please stand by while rebooting the system...


BUFFALO CFE Version 1.04
Memory Test start(0xA0100000) end(0xA8000000) size(33292288)
Data line test start:0xa0100000 pattern 0x00000001 0x00000003 0x00000007 0x0000000F 0x00000005 0x00000015 0x00000055 0xAAAAAAAA
Address line test start:0xa0100000 len:0x7f00000 pattern 0xAAAAAAAA 0x55555555  
Fill test patnum:2
fill Pattern 5555AAAA  Writing...   Reading...
fill Pattern AAAA5555  Writing...   Reading...
Decompressing...done


CFE version 6.30.15.3 (r315282) based on BBP 1.0.37 for BCM947XX (32bit,SP,LE)
Build Date: Tue Apr 24 09:04:01 JST 2012 (root@fc15.localdomain)
Copyright (C) 2000-2008 Broadcom Corporation.

Init Arena
Initializing PCI. [normal]
PCI bus 0 slot 0/0: vendor 0x14e4 product 0x0800 (flash memory, rev 0x01)
PCI bus 0 slot 1/0: vendor 0x14e4 product 0x4715 (ethernet network, rev 0x01)
PCI bus 0 slot 4/0: vendor 0x14e4 product 0x471a (USB serial bus, interface 0x10, rev 0x01)
PCI bus 0 slot 4/1: vendor 0x14e4 product 0x471a (USB serial bus, interface 0x20, rev 0x01)
PCI bus 0 slot 5/0: vendor 0x14e4 product 0x0820 (PCI bridge, rev 0x01)
PCI bus 0 slot 6/0: vendor 0x14e4 product 0x0820 (PCI bridge, rev 0x01)
PCI bus 0 slot 7/0: vendor 0x14e4 product 0x052e (undefined subclass 0xff, interface 0xff, rev 0x01)
PCI bus 0 slot 8/0: vendor 0x14e4 product 0x080e (RAM memory, rev 0x01)
PCI bus 0 slot 9/0: vendor 0x14e4 product 0x0534 (undefined subclass 0xff, interface 0xff, rev 0x01)
Init Devs.
Boot partition size = 262144(0x40000)
Found an ST compatible serial flash with 32 64KB blocks; total size 2MB
Found a Samsung (1 bit-cell) NAND flash with 2048B pages or 128KB blocks; total size 128MB
bcm_robo_enable_switch: EEE is disabled
et0: Broadcom BCM47XX 10/100/1000 Mbps Ethernet Controller 6.30.15.3 (r315282)
CPU type 0x19749: 600MHz
Tot mem: 131072 KBytes

CFE mem:    0x87000000 - 0x87164A60 (1460832)
Data:       0x8704C9A0 - 0x87050BA0 (16896)
BSS:        0x87050BA0 - 0x87062A60 (73408)
Heap:       0x87062A60 - 0x87162A60 (1048576)
Stack:      0x87162A60 - 0x87164A60 (8192)
Text:       0x87000000 - 0x8704C994 (313748)

DRAM magic offset:001E0000 size:00010000
DRAM magic found
Device eth0:  hwaddr 12-6F-3F-81-43-2F, ipaddr 192.168.11.1, mask 255.255.255.0
        gateway not set, nameserver not set
check_trx: start nflash1.trx
check_trx: exit nflash1.trx
Loader:raw Filesys:raw Dev:nflash0.os File: Optionsnull)
Loading: .. 3191392 bytes read
Entry at 0x80001000
Closing network.
Starting program at 0x80001000
Linux version 2.6.22.19 (root@asus) (gcc version 4.2.4) #13 Wed Jun 25 06:39:11 CST 2014
CPU revision is: 00019749
Found an ST compatible serial flash with 32 64KB blocks; total size 2MB
Determined physical RAM map:
memory: 07fff000 @ 00000000 (usable)
Zone PFN ranges:
  Normal          0 ->    32767
  HighMem     32767 ->    32767
early_node_map[1] active PFN ranges
    0:        0 ->    32767
Built 1 zonelists.  Total pages: 32767
Kernel command line: root=/dev/mtdblock3 console=ttyS0,115200 init=/sbin/preinit
Primary instruction cache 32kB, physically tagged, 4-way, linesize 32 bytes.
Primary data cache 32kB, 4-way, linesize 32 bytes.
Synthesized TLB refill handler (20 instructions).
Synthesized TLB load handler fastpath (32 instructions).
Synthesized TLB store handler fastpath (32 instructions).
Synthesized TLB modify handler fastpath (31 instructions).
PID hash table entries: 512 (order: 9, 2048 bytes)
CPU: BCM5300 rev 1 pkg 0 at 600 MHz
Using 300.000 MHz high precision timer.
console [ttyS0] enabled
Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
Memory: 126108k/131068k available (2518k kernel code, 4808k reserved, 397k data, 200k init, 0k highmem)
Mount-cache hash table entries: 512
NET: Registered protocol family 16
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
PCI: Initializing host
PCI: Reset RC
PCI: Initializing host
PCI: Reset RC
PCI: Fixing up bus 0
PCI/PCIe coreunit 0 is set to bus 1.
PCI: Fixing up bridge
PCI: Fixing up bridge
PCI: Enabling device 0000:01:00.1 (0004 -> 0006)
PCI: Fixing up bus 1
PCI/PCIe coreunit 1 is set to bus 2.
PCI: Fixing up bridge
PCI: Fixing up bridge
PCI: Enabling device 0000:02:00.1 (0004 -> 0006)
PCI: Fixing up bus 2
NET: Registered protocol family 2
Time: MIPS clocksource has been installed.
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
TCP established hash table entries: 4096 (order: 3, 32768 bytes)
TCP bind hash table entries: 4096 (order: 2, 16384 bytes)
TCP: Hash tables configured (established 4096 bind 4096)
TCP reno registered
squashfs: version 3.2-r2 (2007/01/15) Phillip Lougher
io scheduler noop registered (default)
HDLC line discipline: version $Revision: 4.8 $, maxframe=4096
N_HDLC line discipline registered.
Serial: 8250/16550 driver $Revision: 1.90 $ 2 ports, IRQ sharing disabled
serial8250: ttyS0 at MMIO 0x0 (irq = 8) is a 16550A
serial8250: ttyS1 at MMIO 0x0 (irq = 8) is a 16550A
PPP generic driver version 2.4.2
MPPE/MPPC encryption/compression module registered
NET: Registered protocol family 24
PPPoL2TP kernel driver, V0.18.3
PPTP driver version 0.8.5
pflash: found no supported devices
Boot partition size = 262144(0x40000)
Creating 2 MTD partitions on "sflash":
0x00000000-0x00040000 : "pmon"
0x001f0000-0x00200000 : "nvram"
Found a Samsung NAND flash with 2048B pages or 128KB blocks; total size 128MB
lookup_nflash_rootfs_offset: offset = 0x0
nflash: squash filesystem with lzma found at block 8
Creating 2 MTD partitions on "nflash":
0x00000000-0x02000000 : "linux"
0x00118c44-0x02000000 : "rootfs"
NAND device: Manufacturer ID: 0xec, Chip ID: 0xf1 (Samsung NAND 128MiB 3,3V 8-bit)
Creating 3 MTD partitions on "brcmnand":
0x00000000-0x02000000 : "trx"
0x02000000-0x04000000 : "jffs2"
0x04000000-0x07f00000 : "brcmnand"
dev_nvram_init: _nvram_init
_nvram_init: allocat size= 65536
usbcore: registered new interface driver hiddev
usbcore: registered new interface driver usbhid
drivers/hid/usbhid/hid-core.c: v2.6:USB HID core driver
u32 classifier
    OLD policer on
Netfilter messages via NETLINK v0.30.
nf_conntrack version 0.5.0 (1024 buckets, 8192 max)
ip_tables: (C) 2000-2006 Netfilter Core Team
ipt_account 0.1.21 : Piotr Gasidlo <quaker@barbara.eu.org>, http://www.barbara.eu.org/~quaker/ipt_account/
net/ipv4/netfilter/tomato_ct.c [Jun 25 2014 06:11:43]
NET: Registered protocol family 1
NET: Registered protocol family 10
ip6_tables: (C) 2000-2006 Netfilter Core Team
NET: Registered protocol family 17
802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>
All bugs added by David S. Miller <davem@redhat.com>
VFS: Mounted root (squashfs filesystem) readonly.
Freeing unused kernel memory: 200k freed
Warning: unable to open an initial console.
Failed to execute /sbin/preinit.  Attempting defaults...
emf: module license 'Proprietary' taints kernel.
et_module_init: passivemode set to 0x0
et_module_init: et_txq_thresh set to 0x0
bcm_robo_enable_switch: EEE is disabled
eth0: Broadcom BCM47XX 10/100/1000 Mbps Ethernet Controller 6.30.39.31 (r341183)
PCI: Enabling device 0000:01:01.0 (0000 -> 0002)
eth1: Broadcom BCM43a2 802.11 Wireless Controller 6.30.102.9 (r366174)
PCI: Enabling device 0000:02:01.0 (0000 -> 0002)
eth2: Broadcom BCM4331 802.11 Wireless Controller 6.30.102.9 (r366174)
/ # lo: File exists
Restarting system.
Please stand by while rebooting the system...


BUFFALO CFE Version 1.04
Memory Test start(0xA0100000) end(0xA8000000) size(33292288)
Data line test start:0xa0100000 pattern 0x00000001 0x00000003 0x00000007 0x0000000F 0x00000005 0x00000015 0x00000055 0xAAAAAAAA
Address line test start:0xa0100000 len:0x7f00000 pattern 0xAAAAAAAA 0x55555555  
Fill test patnum:2
fill Pattern 5555AAAA  Writing...   Reading...
fill Pattern AAAA5555  Writing...   Reading...
Decompressing...done


CFE version 6.30.15.3 (r315282) based on BBP 1.0.37 for BCM947XX (32bit,SP,LE)
Build Date: Tue Apr 24 09:04:01 JST 2012 (root@fc15.localdomain)
Copyright (C) 2000-2008 Broadcom Corporation.

Init Arena
Initializing PCI. [normal]
PCI bus 0 slot 0/0: vendor 0x14e4 product 0x0800 (flash memory, rev 0x01)
PCI bus 0 slot 1/0: vendor 0x14e4 product 0x4715 (ethernet network, rev 0x01)
PCI bus 0 slot 4/0: vendor 0x14e4 product 0x471a (USB serial bus, interface 0x10, rev 0x01)
PCI bus 0 slot 4/1: vendor 0x14e4 product 0x471a (USB serial bus, interface 0x20, rev 0x01)
PCI bus 0 slot 5/0: vendor 0x14e4 product 0x0820 (PCI bridge, rev 0x01)
PCI bus 0 slot 6/0: vendor 0x14e4 product 0x0820 (PCI bridge, rev 0x01)
PCI bus 0 slot 7/0: vendor 0x14e4 product 0x052e (undefined subclass 0xff, interface 0xff, rev 0x01)
PCI bus 0 slot 8/0: vendor 0x14e4 product 0x080e (RAM memory, rev 0x01)
PCI bus 0 slot 9/0: vendor 0x14e4 product 0x0534 (undefined subclass 0xff, interface 0xff, rev 0x01)
Init Devs.
Boot partition size = 262144(0x40000)
Found an ST compatible serial flash with 32 64KB blocks; total size 2MB
Found a Samsung (1 bit-cell) NAND flash with 2048B pages or 128KB blocks; total size 128MB
bcm_robo_enable_switch: EEE is disabled
et0: Broadcom BCM47XX 10/100/1000 Mbps Ethernet Controller 6.30.15.3 (r315282)
CPU type 0x19749: 600MHz
Tot mem: 131072 KBytes

CFE mem:    0x87000000 - 0x87164A60 (1460832)
Data:       0x8704C9A0 - 0x87050BA0 (16896)
BSS:        0x87050BA0 - 0x87062A60 (73408)
Heap:       0x87062A60 - 0x87162A60 (1048576)
Stack:      0x87162A60 - 0x87164A60 (8192)
Text:       0x87000000 - 0x8704C994 (313748)

DRAM magic offset:001E0000 size:00010000
DRAM magic found
Device eth0:  hwaddr 12-6F-3F-81-43-2F, ipaddr 192.168.11.1, mask 255.255.255.0
        gateway not set, nameserver not set
check_trx: start nflash1.trx
check_trx: exit nflash1.trx
Loader:raw Filesys:raw Dev:nflash0.os File: Optionsnull)
Loading: .. 3191392 bytes read
Entry at 0x80001000
Closing network.
Starting program at 0x80001000
Linux version 2.6.22.19 (root@asus) (gcc version 4.2.4) #13 Wed Jun 25 06:39:11 CST 2014
CPU revision is: 00019749
Found an ST compatible serial flash with 32 64KB blocks; total size 2MB
Determined physical RAM map:
memory: 07fff000 @ 00000000 (usable)
Zone PFN ranges:
  Normal          0 ->    32767
  HighMem     32767 ->    32767
early_node_map[1] active PFN ranges
    0:        0 ->    32767
Built 1 zonelists.  Total pages: 32767
Kernel command line: root=/dev/mtdblock3 console=ttyS0,115200 init=/sbin/preinit
Primary instruction cache 32kB, physically tagged, 4-way, linesize 32 bytes.
Primary data cache 32kB, 4-way, linesize 32 bytes.
Synthesized TLB refill handler (20 instructions).
Synthesized TLB load handler fastpath (32 instructions).
Synthesized TLB store handler fastpath (32 instructions).
Synthesized TLB modify handler fastpath (31 instructions).
PID hash table entries: 512 (order: 9, 2048 bytes)
CPU: BCM5300 rev 1 pkg 0 at 600 MHz
Using 300.000 MHz high precision timer.
console [ttyS0] enabled
Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
Memory: 126108k/131068k available (2518k kernel code, 4808k reserved, 397k data, 200k init, 0k highmem)
Mount-cache hash table entries: 512
NET: Registered protocol family 16
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
PCI: Initializing host
PCI: Reset RC
PCI: Initializing host
PCI: Reset RC
PCI: Fixing up bus 0
PCI/PCIe coreunit 0 is set to bus 1.
PCI: Fixing up bridge
PCI: Fixing up bridge
PCI: Enabling device 0000:01:00.1 (0004 -> 0006)
PCI: Fixing up bus 1
PCI/PCIe coreunit 1 is set to bus 2.
PCI: Fixing up bridge
PCI: Fixing up bridge
PCI: Enabling device 0000:02:00.1 (0004 -> 0006)
PCI: Fixing up bus 2
NET: Registered protocol family 2
Time: MIPS clocksource has been installed.
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
TCP established hash table entries: 4096 (order: 3, 32768 bytes)
TCP bind hash table entries: 4096 (order: 2, 16384 bytes)
TCP: Hash tables configured (established 4096 bind 4096)
TCP reno registered
squashfs: version 3.2-r2 (2007/01/15) Phillip Lougher
io scheduler noop registered (default)
HDLC line discipline: version $Revision: 4.8 $, maxframe=4096
N_HDLC line discipline registered.
Serial: 8250/16550 driver $Revision: 1.90 $ 2 ports, IRQ sharing disabled
serial8250: ttyS0 at MMIO 0x0 (irq = 8) is a 16550A
serial8250: ttyS1 at MMIO 0x0 (irq = 8) is a 16550A
PPP generic driver version 2.4.2
MPPE/MPPC encryption/compression module registered
NET: Registered protocol family 24
PPPoL2TP kernel driver, V0.18.3
PPTP driver version 0.8.5
pflash: found no supported devices
Boot partition size = 262144(0x40000)
Creating 2 MTD partitions on "sflash":
0x00000000-0x00040000 : "pmon"
0x001f0000-0x00200000 : "nvram"
Found a Samsung NAND flash with 2048B pages or 128KB blocks; total size 128MB
lookup_nflash_rootfs_offset: offset = 0x0
nflash: squash filesystem with lzma found at block 8
Creating 2 MTD partitions on "nflash":
0x00000000-0x02000000 : "linux"
0x00118c44-0x02000000 : "rootfs"
NAND device: Manufacturer ID: 0xec, Chip ID: 0xf1 (Samsung NAND 128MiB 3,3V 8-bit)
Creating 3 MTD partitions on "brcmnand":
0x00000000-0x02000000 : "trx"
0x02000000-0x04000000 : "jffs2"
0x04000000-0x07f00000 : "brcmnand"
dev_nvram_init: _nvram_init
_nvram_init: allocat size= 65536
usbcore: registered new interface driver hiddev
usbcore: registered new interface driver usbhid
drivers/hid/usbhid/hid-core.c: v2.6:USB HID core driver
u32 classifier
    OLD policer on
Netfilter messages via NETLINK v0.30.
nf_conntrack version 0.5.0 (1024 buckets, 8192 max)
ip_tables: (C) 2000-2006 Netfilter Core Team
ipt_account 0.1.21 : Piotr Gasidlo <quaker@barbara.eu.org>, http://www.barbara.eu.org/~quaker/ipt_account/
net/ipv4/netfilter/tomato_ct.c [Jun 25 2014 06:11:43]
NET: Registered protocol family 1
NET: Registered protocol family 10
ip6_tables: (C) 2000-2006 Netfilter Core Team
NET: Registered protocol family 17
802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>
All bugs added by David S. Miller <davem@redhat.com>
VFS: Mounted root (squashfs filesystem) readonly.
Freeing unused kernel memory: 200k freed
Warning: unable to open an initial console.
Failed to execute /sbin/preinit.  Attempting defaults...
emf: module license 'Proprietary' taints kernel.
et_module_init: passivemode set to 0x0
et_module_init: et_txq_thresh set to 0x0
bcm_robo_enable_switch: EEE is disabled
eth0: Broadcom BCM47XX 10/100/1000 Mbps Ethernet Controller 6.30.39.31 (r341183)
PCI: Enabling device 0000:01:01.0 (0000 -> 0002)
eth1: Broadcom BCM43a2 802.11 Wireless Controller 6.30.102.9 (r366174)
PCI: Enabling device 0000:02:01.0 (0000 -> 0002)
eth2: Broadcom BCM4331 802.11 Wireless Controller 6.30.102.9 (r366174)
/ # lo: File exists

本帖子中包含更多资源

您需要 登录 才可以下载或查看,没有账号?立即注册

×
我的恩山、我的无线 The best wifi forum is right here.
发表于 2014-7-28 18:16 | 显示全部楼层
绳命在于折腾!
我的恩山、我的无线 The best wifi forum is right here.
回复

使用道具 举报

发表于 2014-7-28 18:17 来自手机 | 显示全部楼层
这贴是公正的
我的恩山、我的无线 The best wifi forum is right here.
回复

使用道具 举报

发表于 2014-7-28 18:48 | 显示全部楼层
玩家还需要加强自身的知识储备啊
我的恩山、我的无线 The best wifi forum is right here.
回复

使用道具 举报

 楼主| 发表于 2014-7-28 18:53 | 显示全部楼层
测试一小时无问题,


本帖子中包含更多资源

您需要 登录 才可以下载或查看,没有账号?立即注册

×
我的恩山、我的无线 The best wifi forum is right here.
回复

使用道具 举报

发表于 2014-7-28 19:36 | 显示全部楼层
看来BCM机器不是很好折腾,
玩家需要多多学习点折腾常识啊
我的恩山、我的无线 The best wifi forum is right here.
回复

使用道具 举报

发表于 2014-7-28 19:41 来自手机 | 显示全部楼层
A版主竟然不使用拼音输入法
我的恩山、我的无线 The best wifi forum is right here.
回复

使用道具 举报

您需要登录后才可以回帖 登录 | 立即注册

本版积分规则

有疑问请添加管理员QQ86788181|手机版|小黑屋|Archiver|恩山无线论坛(常州市恩山计算机开发有限公司版权所有) ( 苏ICP备05084872号 )

GMT+8, 2024-3-28 22:20

Powered by Discuz! X3.5

© 2001-2024 Discuz! Team.

| 江苏省互联网有害信息举报中心 举报信箱:js12377 | @jischina.com.cn 举报电话:025-88802724 本站不良内容举报信箱:68610888@qq.com 举报电话:0519-86695797

快速回复 返回顶部 返回列表