|
|
本帖最后由 数不清 于 2014-8-10 21:10 编辑
高性能低价格的UBNT EdgeRouter Lite,TB二手价￥300，内置系统基于Vyatta 6.3。
| Ubiquiti ERL | EnGenius ESR750H | ASUS RT-AC66U | CPU | Cavium CN5020 | Ralink RT3883F | Broadcom BCM4706 | Switch or Ethernet | Atheros AR8035 Gigabit PHY (x3) | Atheros AR8327 | Broadcom BCM53125 | RAM | 512 MB | 256 MB | 256 MB | Flash | 2 GB + 8 MB | 16 MB | 128 MB |
数据吞吐率：Test Description | Ubiquiti ERL | EnGenius ESR750H | ASUS RT-AC66U | | WAN - LAN | 822 | 890 | 836 | | LAN - WAN | 773 | 907 | 839 | | Total Simultaneous | 1307 | 868 | 820 | | Maximum Simultaneous Connections | 29354 | 29666 | 30069 | | Firmware Version | 1.0.2 | 1.3.4 | 3.0.0.4.164 |
安装步骤：
1.大于2G U盘一个，格式化俩分区(FAT/ext3)
# Device Boot Start End Blocks Id System
# /dev/sdd1 2048 292863 145408 c W95 FAT32 (LBA)
# /dev/sdd2 292864 3710975 1709056 83 Linux
2.下载openwrt-octeon-erlite-sysupgrade.tar解压;
3.将sysupgrade-erlite目录下kernel 改名vmlinux.64，复制到第一个分区根目录下，用md5sum生成md5码，md5码保存成vmlinux.64.md5文件也复制到根目录下；
4.将sysupgrade-erlite目录下root，用dd写入第二个分区“ dd if=/路径/root of=/dev/U盘 bs=4096”
5. sync
6，将U盘插入erlite,通电启动。
[ 0.000000] Linux version 3.10.49 (johnny@ThinkPad) (gcc version 4.6.4 (OpenWrt/Linaro GCC 4.6-2013.05 r41989) ) #3 SMP Fri Aug 8 21:49:58 CST 2014
[ 0.000000] CVMSEG size: 2 cache lines (256 bytes)
[ 0.000000] bootconsole [early0] enabled
[ 0.000000] CPU revision is: 000d0601 (Cavium Octeon+)
[ 0.000000] Checking for the multiply/shift bug... no.
[ 0.000000] Checking for the daddiu bug... no.
[ 0.000000] Determined physical RAM map:
[ 0.000000] memory: 0000000006800000 @ 0000000001600000 (usable)
[ 0.000000] memory: 0000000007c00000 @ 0000000008200000 (usable)
[ 0.000000] memory: 000000000fc00000 @ 0000000410000000 (usable)
[ 0.000000] memory: 00000000004a9bd0 @ 0000000001100000 (usable)
[ 0.000000] Wasting 243712 bytes for tracking 4352 unused pages
[ 0.000000] Initrd not found or empty - disabling initrd
[ 0.000000] Using internal Device Tree.
[ 0.000000] software IO TLB [mem 0x01d8b000-0x05d8b000] (64MB) mapped at [a800000001d8b000-a800000005d8afff]
[ 0.000000] Zone ranges:
[ 0.000000] DMA32 [mem 0x01100000-0xefffffff]
[ 0.000000] Normal [mem 0xf0000000-0x41fbfffff]
[ 0.000000] Movable zone start for each node
[ 0.000000] Early memory node ranges
[ 0.000000] node 0: [mem 0x01100000-0x015a8fff]
[ 0.000000] node 0: [mem 0x01600000-0x07dfffff]
[ 0.000000] node 0: [mem 0x08200000-0x0fdfffff]
[ 0.000000] node 0: [mem 0x410000000-0x41fbfffff]
[ 0.000000] On node 0 totalpages: 124073
[ 0.000000] DMA32 zone: 815 pages used for memmap
[ 0.000000] DMA32 zone: 0 pages reserved
[ 0.000000] DMA32 zone: 59561 pages, LIFO batch:15
[ 0.000000] Normal zone: 882 pages used for memmap
[ 0.000000] Normal zone: 64512 pages, LIFO batch:15
[ 0.000000] Primary instruction cache 32kB, virtually tagged, 4 way, 64 sets, linesize 128 bytes.
[ 0.000000] Primary data cache 16kB, 64-way, 2 sets, linesize 128 bytes.
[ 0.000000] PERCPU: Embedded 10 pages/cpu @a800000005e46000 s12160 r8192 d20608 u40960
[ 0.000000] pcpu-alloc: s12160 r8192 d20608 u40960 alloc=10*4096
[ 0.000000] pcpu-alloc: [0] 0 [0] 1
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 122376
[ 0.000000] Kernel command line: bootoctlinux $loadaddr coremask=0x3 root=/dev/sda2 rootdelay=15 rw rootsqimg=squashfs.img rootsqwdir=w mtdparts=phys_mapped_flash:512k(boot0),512k(boot1),64k@3072k(eeprom) console=ttyS0,115200
[ 0.000000] PID hash table entries: 2048 (order: 2, 16384 bytes)
[ 0.000000] Dentry cache hash table entries: 65536 (order: 7, 524288 bytes)
[ 0.000000] Inode-cache hash table entries: 32768 (order: 6, 262144 bytes)
[ 0.000000] Memory: 417168k/496292k available (3163k kernel code, 79124k reserved, 1050k data, 264k init, 0k highmem)
[ 0.000000] Hierarchical RCU implementation.
[ 0.000000] CONFIG_RCU_FANOUT set to non-default value of 32
[ 0.000000] RCU restricting CPUs from NR_CPUS=16 to nr_cpu_ids=2.
[ 0.000000] NR_IRQS:127
[ 7.760874] Calibrating delay loop (skipped) preset value.. 1000.00 BogoMIPS (lpj=2000000)
[ 7.768969] pid_max: default: 32768 minimum: 301
[ 7.773801] Mount-cache hash table entries: 256
[ 7.779170] Checking for the daddi bug... no.
[ 7.785162] SMP: Booting CPU01 (CoreId 1)...
[ 7.789416] CPU revision is: 000d0601 (Cavium Octeon+)
[ 7.789829] Brought up 2 CPUs
[ 7.802177] NET: Registered protocol family 16
[ 7.808832] Not in host mode, PCI Controller not initialized
[ 7.837077] bio: create slab <bio-0> at 0
[ 7.843245] SCSI subsystem initialized
[ 7.848520] usbcore: registered new interface driver usbfs
[ 7.854260] usbcore: registered new interface driver hub
[ 7.859906] usbcore: registered new device driver usb
[ 7.866962] Switching to clocksource OCTEON_CVMCOUNT
[ 7.876778] NET: Registered protocol family 2
[ 7.881806] TCP established hash table entries: 4096 (order: 4, 65536 bytes)
[ 7.888877] TCP bind hash table entries: 4096 (order: 5, 131072 bytes)
[ 7.895440] TCP: Hash tables configured (established 4096 bind 4096)
[ 7.901733] TCP: reno registered
[ 7.904893] UDP hash table entries: 256 (order: 2, 24576 bytes)
[ 7.910791] UDP-Lite hash table entries: 256 (order: 2, 24576 bytes)
[ 7.917521] NET: Registered protocol family 1
[ 7.921814] PCI: CLS 0 bytes, default 128
[ 7.934833] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 7.940625] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[ 7.950699] msgmni has been set to 814
[ 7.954987] io scheduler noop registered
[ 7.958790] io scheduler deadline registered (default)
[ 7.964365] octeon_gpio 1070000000800.gpio-controller: version: 1.0
[ 7.971326] Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled
[ 7.979751] octeon_rng octeon_rng: Octeon Random Number Generator
[ 7.989191] of-flash 1f400000.nor: Can't get bank width from device tree
[ 7.996579] libphy: mdio-octeon: probed
[ 8.002690] mdio-octeon 1180000001800.mdio: Version 1.0
[ 8.008588] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 8.015377] ehci-pci: EHCI PCI platform driver
[ 8.020077] ehci-platform: EHCI generic platform driver
[ 8.025648] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[ 8.032804] usbcore: registered new interface driver usb-storage
[ 8.038687] octeon_wdt: Initial granularity 5 Sec
[ 8.043927] cavium-ethernet 1.9
[ 8.049639] Interface 0 has 3 ports (RGMII)
[ 8.070507] OcteonUSB OcteonUSB.0: Octeon Host Controller
[ 8.075799] OcteonUSB OcteonUSB.0: new USB bus registered, assigned bus number 1
[ 8.083210] OcteonUSB OcteonUSB.0: irq 124, io mem 0x00000000
[ 8.089978] hub 1-0:1.0: USB hub found
[ 8.093646] hub 1-0:1.0: 1 port detected
[ 8.098391] TCP: cubic registered
[ 8.101591] NET: Registered protocol family 17
[ 8.106793] 1180000000800.serial: ttyS0 at MMIO 0x1180000000800 (irq = 34) is a OCTEON
[ 8.114615] console [ttyS0] enabled, bootconsole disabled
[ 8.126230] 1180000000c00.serial: ttyS1 at MMIO 0x1180000000c00 (irq = 35) is a OCTEON
[ 8.134977] Bootbus flash: Setting flash for 4MB flash at 0x1f800000
[ 8.141430] phys_mapped_flash: Found 1 x16 devices at 0x0 in 8-bit bank. Manufacturer ID 0x0000c2 Chip ID 0x0000a7
[ 8.151807] Amd/Fujitsu Extended Query Table at 0x0040
[ 8.156978] Amd/Fujitsu Extended Query version 1.1.
[ 8.162049] phys_mapped_flash: Swapping erase regions for top-boot CFI ta??ޭ
[ 8.169028] number of CFI chips: 1
[ 8.172656] 3 cmdlinepart partitions found on MTD device phys_mapped_flash
[ 8.179549] Creating 3 MTD partitions on "phys_mapped_flash":
[ 8.185320] 0x000000000000-0x000000080000 : "boot0"
[ 8.192217] 0x000000080000-0x000000100000 : "boot1"
[ 8.199122] 0x000000300000-0x000000310000 : "eeprom"
[ 8.207984] Waiting 15sec before mounting root device...
[ 8.439884] usb 1-1: new high-speed USB device number 2 using OcteonUSB
[ 8.625646] usb-storage 1-1:1.0: USB Mass Storage device detected
[ 8.632120] scsi0 : usb-storage 1-1:1.0
[ 9.052002] eth0: 1000 Mbps Full duplex, port 0, queue 0
[ 9.057644] eth1: 1000 Mbps Full duplex, port 1, queue 1
[ 9.636578] scsi 0:0:0:0: Direct-Access Generic Flash Disk 5.00 PQ: 0 ANSI: 2
[ 9.647165] sd 0:0:0:0: [sda] 6593280 512-byte logical blocks: (3.37 GB/3.14 GiB)
[ 9.655371] sd 0:0:0:0: [sda] Write Protect is off
[ 9.660238] sd 0:0:0:0: [sda] Mode Sense: 0b 00 00 08
[ 9.660609] sd 0:0:0:0: [sda] No Caching mode page found
[ 9.665976] sd 0:0:0:0: [sda] Assuming drive cache: write through
[ 9.674470] sd 0:0:0:0: [sda] No Caching mode page found
[ 9.679851] sd 0:0:0:0: [sda] Assuming drive cache: write through
[ 9.686975] sda: sda1 sda2
[ 9.693226] sd 0:0:0:0: [sda] No Caching mode page found
[ 9.698616] sd 0:0:0:0: [sda] Assuming drive cache: write through
[ 9.704756] sd 0:0:0:0: [sda] Attached SCSI removable disk
[ 23.217998] EXT4-fs (sda2): couldn't mount as ext3 due to feature incompatibilities
[ 23.227732] EXT4-fs (sda2): couldn't mount as ext2 due to feature incompatibilities
[ 23.415785] EXT4-fs (sda2): mounted filesystem without journal. Opts: (null)
[ 23.422944] VFS: Mounted root (ext4 filesystem) on device 8:2.
[ 23.429070] Freeing unused kernel memory: 264K (ffffffff8151e000 - ffffffff81560000)
[ 23.840729] uhci_hcd: USB Universal Host Controller Interface driver
[ 27.742353] EXT4-fs (sda2): re-mounted. Opts: (null)
[ 29.952959] NET: Registered protocol family 10
[ 29.969073] device-mapper: ioctl: 4.24.0-ioctl (2013-01-15) initialised: dm-devel@redhat.com
[ 29.986372] tun: Universal TUN/TAP device driver, 1.6
[ 29.991469] tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
[ 30.005420] sit: IPv6 over IPv4 tunneling driver
[ 30.026879] nf_conntrack version 0.5.0 (3261 buckets, 13044 max)
[ 30.039739] ip6_tables: (C) 2000-2006 Netfilter Core Team
[ 30.082894] u32 classifier
[ 30.085720] input device check on
[ 30.089486] Actions configured
[ 30.101030] Mirror/redirect action on
[ 30.125245] Loading modules backported from Linux version master-2014-05-22-0-gf2032ea
[ 30.133239] Backport generated by backports.git backports-20140320-37-g5c33da0
[ 30.149987] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 30.207372] usbcore: registered new interface driver ums-alauda
[ 30.214828] usbcore: registered new interface driver ums-cypress
[ 30.222461] usbcore: registered new interface driver ums-datafab
[ 30.229996] usbcore: registered new interface driver ums-freecom
[ 30.237663] usbcore: registered new interface driver ums-isd200
[ 30.245234] usbcore: registered new interface driver ums-jumpshot
[ 30.253015] usbcore: registered new interface driver ums-karma
[ 30.260615] usbcore: registered new interface driver ums-sddr09
[ 30.268248] usbcore: registered new interface driver ums-sddr55
[ 30.275913] usbcore: registered new interface driver ums-usbat
[ 30.319581] xt_time: kernel timezone is -0000
[ 30.350287] cfg80211: Calling CRDA to update world regulatory domain
[ 30.358918] cfg80211: World regulatory domain updated:
[ 30.364134] cfg80211: DFS Master region: unset
[ 30.368570] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp), (dfs_cac_time)
[ 30.378389] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A)
[ 30.386452] cfg80211: (2457000 KHz - 2482000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A)
[ 30.394506] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (N/A, 2000 mBm), (N/A)
[ 30.402555] cfg80211: (5170000 KHz - 5250000 KHz @ 160000 KHz), (N/A, 2000 mBm), (N/A)
[ 30.410674] cfg80211: (5250000 KHz - 5330000 KHz @ 160000 KHz), (N/A, 2000 mBm), (0 s)
[ 30.418786] cfg80211: (5490000 KHz - 5730000 KHz @ 160000 KHz), (N/A, 2000 mBm), (0 s)
[ 30.426896] cfg80211: (5735000 KHz - 5835000 KHz @ 80000 KHz), (N/A, 2000 mBm), (N/A)
[ 30.434921] cfg80211: (57240000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 0 mBm), (N/A)
[ 30.499563] PPP generic driver version 2.4.2
[ 30.506773] NET: Registered protocol family 24
[ 42.064747] device eth0 entered promiscuous mode
[ 42.070516] br-lan: port 1(eth0) entered forwarding state
[ 42.076035] br-lan: port 1(eth0) entered forwarding state
[ 44.079875] br-lan: port 1(eth0) entered forwarding state
|
本帖子中包含更多资源
您需要 登录 才可以下载或查看，没有账号？立即注册
×
|
简体中文
繁體中文
English
日本語
Deutsch
한국 사람
بالعربية
TÜRKÇE
português
คนไทย
IP卡
狗仔卡
发表于 2014-8-9 18:08
置顶卡
沉默卡
喧嚣卡
顶贴卡
显身卡
跑个OpenSSL Benchmark上个结果看看呢