找回密码
 立即注册

QQ登录

只需一步,快速开始

搜索
广告投放联系QQ68610888
查看: 11367|回复: 9

【求助】水星MW300R V6 TTL刷机的教程

[复制链接]
发表于 2015-5-7 19:24 | 显示全部楼层 |阅读模式
本帖最后由 gongrf2015 于 2015-5-7 19:38 编辑

最近在网上看到可以用PL2303芯片TTL刷路由,心想手上有个C52单片机开发板的板子,上面用的就是PL2303芯片下载
而且有USB转串口(MAX232芯片)的功能,逐拿手上的水星MW300R V6 路由做试验,因为是菜鸟,只做能否中断进入刷机模式。

路由与板子连接好后,开SecureCRT软件进行测试(映射键使用VK_C发送参数tpl,问一下VK_键代表什么意思??),按住C键后给路由上电,代码滚动,就是不能中断进刷机模式,SecureCRT软件反馈的信息如下,
求教高手,各位大大,用次方法是否行得通?为何不能中断进刷机模式?
ROMREBOOT
Enter in romStart!
Decompress the main image ......
Decompress the main image OK!


MT7620(MIPS32) BSP build at Jul  5 2013, 09:28:24.

The memory size set to 16MB, physical size is 16MB
enable ephy clock...done. rf reg 29 = 5
The CPU feqenuce set to 580 MHz

Readed system mac from flash: (此处地址也删去)
Conntrack init...
Conntrack init conntrack list ok
mem_initPool is been called: malloc 88*5120 (0x80ed3150 - 0x80f41150)
Conntrack entry (num: 5120) done.
conntrack hash table (size: 1280) done.
mem_initPool is been called: malloc 8*10240 (0x80ebf110 - 0x80ed3110)
Conntrack hash node (num: 10240) done.
conn_proto_gre_init() init done.
Conntrack proto handler done.
Conntrack fragment hash table (size: 32) done.
mem_initPool is been called: malloc 24*128 (0x80ebe4d0 - 0x80ebf0d0)
Conntrack fragment hash node (num: 128) done.
conntrack timer start.
mem_initPool is been called: malloc 44*5120 (0x80e87490 - 0x80ebe490)
Conntrack expect entry (num: 5120) done.
Conntrack expect tplhash table (size: 1280) done.
mem_initPool is been called: malloc 8*5120 (0x80e7d450 - 0x80e87450)
Conntrack expect tplhash node (num: 5120) done.
Conntrack expect addrhash table (size: 1280) done.
mem_initPool is been called: malloc 8*5120 (0x80e73410 - 0x80e7d410)
Conntrack expect addrhash node (num: 5120) done.
conntrack expect init done!
Conntrack helper (num: 100) done.
conntrack help init done!
Conntrack init done!
napt pt init ok!
napt init ok!
rule_init() 104 * 200!
Attaching interface lo0... done

Waitting for RX_DMA_BUSY status Start... done


Tx_Ring addr: 0xa0d1a880!!!

Rx_Ring addr: 0xa0d19860!!!
CDMA_CSG_CFG = 81000007
GDMA1_FWD_CFG = 20710000
Special Tag Disabled
Disable mt7620 PDMA!
Attached IPv4 interface to eth unit 0
usrNetBootConfig: Invalid Argument

Adding 6911 symbols for standalone.


  Creation date: Jul  5 2013, 09:28:24
l2filter_init(): L2Filter init OK!
mem_initPool is been called: malloc 12*10 (0x80ce53d0 - 0x80ce5448)
mem_initPool is been called: malloc 8*20 (0x80ce52f0 - 0x80ce5390)
initFtpAlg(): Done!
initTftpAlg(): Done!
mem_initPool is been called: malloc 32*40 (0x80ce4db0 - 0x80ce52b0)
mem_initPool is been called: malloc 20*20 (0x80ce4be0 - 0x80ce4d70)
alg_init(): ALG INIT OK
mem_initPool is been called: malloc 104*256 (0x80cde3a0 - 0x80ce4ba0)
mem_initPool is been called: malloc -> 16*256 (0x80cdd360 - 0x80cde360)
[ msg_connSrv ] 269:  Can't connect server 7 and retry

[ msg_connSrv ] 269:  Can't connect server 11 and retry

ifMgr_getIfMac: Interface mr0 has NOT been attach to ip stack yet!
starting mirror0
starting mirror1
br0 setup done!
mr0 config done!
[ oal_intf_enableIntf ] 211:  to enable interface eth0 !
IP Detach eth0
eth0 attach to br0 done!
The initString info:
        phyNum=0!
        devNum=0!
        infType=4!
        irqNum=25!
        devType=0!
        privSize=0!
        csrAddr=0x7fffffff!
        devName=ra!


=== pAd = 80a3d9a0, size = 790920 ===

<-- RTMPAllocAdapterBlock, Status=0
AP Driver version-2.7.1.0
RtmpVxNetPoolInit(): malloc for clConfig[0] with size(162848)!
RtmpVxNetPoolInit(): malloc for clConfig[1] with size(1511456)!
rt28xx_ap_ioctl():Not supported ioctl cmd:0x8004651d!
INUM_TO_IVEC=344
RX DESC a08735a0  size = 1024
<-- RTMPAllocTxRxRingMemory, Status=0
RTMP_TimerListAdd: add timer obj 80ad0838!
RTMP_TimerListAdd: add timer obj 80a9bd6c!
RTMP_TimerListAdd: add timer obj 80a9bd4c!
RTMP_TimerListAdd: add timer obj 80a9bd2c!
RTMP_TimerListAdd: add timer obj 80a44600!
RTMP_TimerListAdd: add timer obj 80a4420c!
RTMP_TimerListAdd: add timer obj 80a445dc!
RTMP_TimerListAdd: add timer obj 80a448c0!
RTMP_TimerListAdd: add timer obj 80a4481c!
RTMP_TimerListAdd: add timer obj 80a44840!
RTMP_TimerListAdd: add timer obj 80a9e14c!
RTMP_TimerListAdd: add timer obj 80a9dd58!
RTMP_TimerListAdd: add timer obj 80a9e128!
RTMP_TimerListAdd: add timer obj 80a9e40c!
RTMP_TimerListAdd: add timer obj 80a9e170!
RTMP_TimerListAdd: add timer obj 80a9e194!
RTMP_TimerListAdd: add timer obj 80a9e1b8!
RTMP_TimerListAdd: add timer obj 80aa7214!
RTMP_TimerListAdd: add timer obj 80aa72e8!
RTMP_TimerListAdd: add timer obj 80aa7234!
RTMP_TimerListAdd: add timer obj 80a9e544!
--->RtmpNetTaskInit
<---RtmpNetTaskInit
RTMP_TimerListAdd: add timer obj 80a41b88!
RTMP_TimerListAdd: add timer obj 80a9e490!
Error opening profile "EAPifname=br0
PreAuthifname=br0
session_timeout_interval=0
MaxStaNum=31
IgmpSnEnable=1
EfuseBufferMode=1
"
Key1Str is Invalid key length(0) or Type(0)
Key2Str is Invalid key length(0) or Type(0)
Key3Str is Invalid key length(0) or Type(0)
Key4Str is Invalid key length(0) or Type(0)
1. Phy Mode = 9
2. Phy Mode = 9
E2PROM: D0 target power=0xff20
E2PROM: 40 MW Power Delta= 0
3. Phy Mode = 9
RTMP_TimerListAdd: add timer obj 80a41788!
AntCfgInit: primary/secondary ant 0/1
Initialize RF Central Registers for E2 !!!
Initialize RF Central Registers for E3 !!!
Initialize RF Channel Registers for E2 !!!
Initialize RF Channel Registers for E3 !!!
Initialize RF DCCal Registers for E2 !!!
Initialize RF DCCal Registers for E3 !!!
D1 = -2, D2 = 9, CalCode = 26 !!!
TX BW Filter Calibration !!!
RX BW Filter Calibration !!!
LOFT Calibration Done!
IQCalibration Start!
IQCalibration Done! CH = 0, (gain= 0, phase=3e)
IQCalibration Start!
IQCalibration Done! CH = 1, (gain= 0, phase=3c)
TX IQ Calibration Done!
Sigma_i=276, Sigma_q=273, R_iq=-130
G_imb=-1, Ph_rx=-3
Sigma_i=293, Sigma_q=297, R_iq=-60
G_imb=1, Ph_rx=-1
RTMPSetPhyMode: channel is out of range, use first channel=0
MCS Set = ff ff 00 00 01
SYNC - BBP R4 to 20MHz.l
Link Status Changed - Port1 Link UP. (02)
RTMP_TimerListAdd: add timer obj 80a9eaf8!
ADC clcok selection for E3 !!!
Shielding clock selection !!!
Main bssid = 1c:fa:68:f5:0a:5e
<==== rt28xx_init, Status=0
availableNum(0) devInitStr =0:4:0:1024:4:0:apcli
rt28xx_ap_ioctl():Not supported ioctl cmd:0x8004651d!
pAd->int_enable_reg=0x3fffc
Enrollee PinCode(ra0)           60148469
[ oal_wlan_openVap ] 1279:  Current addHver is 0x0

rt28xx_ap_ioctl():Not supported ioctl cmd:0xc00c6516!
rt28xx_ap_ioctl():Not supported ioctl cmd:0x40046514!
ra0 attach to br0 done!
rt28xx_ap_ioctl():Not supported ioctl cmd:0xc00c6516!
rt28xx_ap_ioctl():Not supported ioctl cmd:0x40046514!
apcli0 attach to br0 done!
[ msg_connSrv ] 269:  Can't connect server 8 and retry

[ msg_connSrv ] 269:  Can't connect server 8 and retry

[ msg_connSrv ] 269:  Can't connect server 8 and retry

[ msg_connSrv ] 269:  Can't connect server 8 and retry

mem_initPool is been called: malloc 60*64 (0x80856b10 - 0x80857a10)
[ msg_connSrv ] 269:  Can't connect server 9 and retry

tc_core_init(): psched_tick_per_us=983040 psched_us_per_tick=1000000    clock_factor=1.000000 tick_in_used=0.983040
HTB ROOT QDISC:  size=1232
+ HTB CLASS:  size=98832
tc_htb_init:  addr=0x808321e0  endAddr=0x8084a3f0  rootqNum=2  classMaxNum=40
SFQ QDISC:  size=129880
tc_sfq_init:  addr=0x80812670  endAddr=0x808321c8  ruleNum=34
PFIFO QDISC:  size=1000
tc_fifo_init:  addr=0x80812270  endAddr=0x80812658  ruleNum=10
FW FILTER:  size=1728
tc_fw_init:  addr=0x80811ba0  endAddr=0x80812260  num=36
Cannot find the device which name is eth1!
no interface name: eth1 found!
ifMgr_setIfDown(): Get interface failed!
[ oal_intf_disableIntf ] 238:  Disable interface eth1 failed!
set mii port 0 value 0x00003100
no interface name: eth1 found!
ifMgr_ifIsUp(): Get interface failed!
[ oal_wan_startL3Interface ] 564:  Start interface ppp0 (layer2 ifName=eth1)
no interface name: eth1 found!
no interface name: eth1 found!
Vlan ID 0 is wrong
ifMgr_setIfMac: Interface eth1 NOT been attach to ip stack yet!
[ oal_intf_enableIntf ] 211:  to enable interface eth1 !
pppLoad():pDrvCtrl->name(ppp0).
pppAttach():pppObj->pDrvCtrl->name(ppp0).
pppAttach():pppObj initialization succeed.
add net default: gateway 169.254.113.2
username:[ msg_connSrv ] 269:  Can't connect server 13 and retry

alg_open(): OK 0
alg_open(): OK 5
delVpnRule() ERROR.
alg_open(): OK 1
delVpnRule() ERROR.
alg_open(): OK 3
delVpnRule() ERROR.
alg_open(): OK 2
Enable mt7620 PDMA!
===>RtmpOSWrielessEventSend eventType=0x8c02
===>RtmpOSWrielessEventSend eventType=0x8c02
===>RtmpOSWrielessEventSend eventType=0x8c02
===>RtmpOSWrielessEventSend eventType=0x8c02
RTMP_TimerListAdd: add timer obj 80ae6518!
RTMP_TimerListAdd: add timer obj 80ae66c4!
RTMP_TimerListAdd: add timer obj 80af94c0!
MIC Different in pairwise msg 2 of 4-way handshake!
MIC Different in pairwise msg 2 of 4-way handshake!
MIC Different in pairwise msg 2 of 4-way handshake!
MIC Different in pairwise msg 2 of 4-way handshake!
rcv PS-POLL (AID=1 not match) from d4:6e:5c:e9:32:15
===>RtmpOSWrielessEventSend eventType=0x8c02
===>RtmpOSWrielessEventSend eventType=0x8c02
===>RtmpOSWrielessEventSend eventType=0x8c02
===>RtmpOSWrielessEventSend eventType=0x8c02

本帖子中包含更多资源

您需要 登录 才可以下载或查看,没有账号?立即注册

×
我的恩山、我的无线 The best wifi forum is right here.
发表于 2015-5-7 22:25 | 显示全部楼层
似乎少了一条线
我的恩山、我的无线 The best wifi forum is right here.
回复

使用道具 举报

 楼主| 发表于 2015-5-8 19:10 | 显示全部楼层
加上GND线也不行
不知道是不是原厂的不支持这种方式刷机,还是说用PL2303芯片不行
有没有高手指点一下,或是给个较详细点的教程链接
我的恩山、我的无线 The best wifi forum is right here.
回复

使用道具 举报

 楼主| 发表于 2015-5-9 16:45 | 显示全部楼层
发现用PL2303芯片不能进中断,改MAX232芯片,捣鼓一阵后,SecureCRT有反应了,就不知道像这种情况算不算进中断了
ROMREBOOT
Enter in romStart!
Decompress the main image ......
Decompress the main image OK!


MT7620(MIPS32) BSP build at Jul  5 2013, 09:28:24.

The memory size set to 16MB, physical size is 16MB
enable ephy clock...done. rf reg 29 = 5
The CPU feqenuce set to 580 MHz

Readed system mac from flash:
^CConntrack init...
Conntrack init conntrack list ok
mem_initPool is been called: malloc 88*5120 (0x80ed3150 - 0x80f41150)
Conntrack entry (num: 5120) done.
conntrack hash table (size: 1280) done.
mem_initPool is been called: malloc 8*10 done.
Conntrack fragment hash table (size: 32) done.
mem_initPool is been called: malloc 24*128 (0x80ebe4d0 - 0x80ebf0d0)
Conntrack fragment hash node (num: 128) done.
conntrack timer start.
mem_initPool is been called: malloc 44*5120 (0x80e87490 - 0x80ebe490)loc 8*5120 (0x80e7d450 - 0x80e87450)
Conntrack expect tplhash node (num: 5120) done.
Conntrack expect addrhash table (size: 1280) d^Cone.
mem_initPool is been called: malloc 8*5120 (0x80e73410 - 0x80e7d410)
Conntrack expect addrhash node (num: 5120) done.
conntrack expect init done!
Conntrack helper (num: 100) don^Ce.
conntrack help init done!
Conntrack init done!
napt pt init ok!
napt init ok!
rule_init() 104 * 200!
Attaching interface lo0... done
^C^C^C
Waitting for RX_DMA_BUSY status Start... done


Tx_Ring addr: 0xa0d1a880!!!

Rx_Ring addr: 0xa0d19860!!!
^CCDMA_CSG_CFG = 81000007
GDMA1_FWD_CFG = 20710000
Special Tag Disabled
Disable mt7620 PDMA!
Attached IPv4 interface to eth unit 0
usrNetBootConfig: Invalid Argument
^C
Adding 6911 symbols for standalone.


  Creation date: Jul  5 2013, 09:28:24
l2filter_init(): L2Filter init OK!
mem_initPool is been called: malloc 12*10 (0x80ce53d0 - 0x80ce5448)
mem_initPool is been called: malloc 8*20 (0x80ce52f0 - 0x80ce5390)
initFtpAlg(): Done!
initTftpAlg(): Done!
mem_initPool is been called: malloc 32*40 (0x80ce4db0 - 0x80ce52b0)
mem_initPool is been called: mala0)
mem_initPool is been called: malloc -> 16*256 (0x80cdd360 - 0x80cde360)
TattttShell restarted.
0x80fd73f0 (tExcTask): 4 messages from interrupt ltShell restarted.

-> tShell restarted.

-> [ msg_connSrv tShell restarted.

-> tShell restarted.

-> tShell restarted.

-> [ msg_connSrv ] 269:  Can't connect server 11 and retry

ifMgr_getIfMac: Interface mr0 has NOT been attach to ip stack yet!
starting mirror0
starting mirror1
br0 setup done!
mr0 config done!
[ oal_intf_enableIntf ] 211:  to enable interface eth0 !
IP Detach eth0
eth0 attach to br0 done!
The initString info:
        phyNum=0!
        devNum=0!
        infType=4!
        irqNum=25!
        devType=0!
        privSize=0!
        csrAddr=0x7fffffff!
        devName=ra!


=== pAd = 80a38920, size = 790920 ===

<-- RTMPAllocAdapterBlock, Status=0
AP Driver version-2.7.1.0
RtmpVxNetPoolInit(): malloc for clConfig[0] with size(162848)!
RtmpVxNetPoolInit(): malloc for clConfig[1] with size(1511456)!
rt28xx_ap_ioctl():Not supported ioctl cmd:0x8004651d!
INUM_TO_IVEC=344
RX DESC a086e4e0  size = 1024
<-- RTMPAllocTxRxRingMemory, Status=0
RTMP_TimerListAdd: add timer obj 80acb7b8!
RTMP_TimerListAdd: add timer obj 80a96cec!
RTMP_TimerListAdd: add timer obj 80a96ccc!
RTMP_TimerListAdd: add timer obj 80a96cac!
RTMP_TimerListAdd: add timer obj 80a3f580!
RTMP_TimerListAdd: add timer obj 80a3f18c!
RTMP_TimerListAdd: add timer obj 80a3f55c!
RTMP_TimerListAdd: add timer obj 80a3f840!
RTMP_TimerListAdd: add timer obj 80a3f79c!
RTMP_TimerListAdd: add timer obj 80a3f7c0!
RTMP_TimerListAdd: add timer obj 80a990cc!
RTMP_TimerListAdd: add timer obj 80a98cd8!
RTMP_TimerListAdd: add timer obj 80a990a8!
RTMP_TimerListAdd: add timer obj 80a9938c!
RTMP_TimerListAdd: add timer obj 80a990f0!
RTMP_TimerListAdd: add timer obj 80a99114!
RTMP_TimerListAdd: add timer obj 80a99138!
RTMP_TimerListAdd: add timer obj 80aa2194!
RTMP_TimerListAdd: add timer obj 80aa2268!
RTMP_TimerListAdd: add timer obj 80aa21b4!
RTMP_TimerListAdd: add timer obj 80a994c4!
--->RtmpNetTaskInit
<---RtmpNetTaskInit
RTMP_TimerListAdd: add timer obj 80a3cb08!
RTMP_TimerListAdd: add timer obj 80a99410!
Error opening profile "EAPifname=br0
PreAuthifname=br0
session_timeout_interval=0
MaxStaNum=31
IgmpSnEnable=1
EfuseBufferMode=1
"
Key1Str is Invalid key length(0) or Type(0)
Key2Str is Invalid key length(0) or Type(0)
Key3Str is Invalid key length(0) or Type(0)
Key4Str is Invalid key length(0) or Type(0)
1. Phy Mode = 9
2. Phy Mode = 9
E2PROM: D0 target power=0xff20
E2PROM: 40 MW Power Delta= 0
3. Phy Mode = 9
RTMP_TimerListAdd: add timer obj 80a3c708!
AntCfgInit: primary/secondary ant 0/1
Initialize RF Central Registers for E2 !!!
Initialize RF Central Registers for E3 !!!
Initialize RF Channel Registers for E2 !!!
Initialize RF Channel Registers for E3 !!!
Initialize RF DCCal Registers for E2 !!!
Initialize RF DCCal Registers for E3 !!!
D1 = -2, D2 = 9, CalCode = 26 !!!
TX BW Filter Calibration !!!
RX BW Filter Calibration !!!
LOFT Calibration Done!
IQCalibration Start!
IQCalibration Done! CH = 0, (gain= 1, phase=3e)
IQCalibration Start!
IQCalibration Done! CH = 1, (gain= 1, phase=3b)
TX IQ Calibration Done!
Sigma_i=286, Sigma_q=283, R_iq=-240
G_imb=-1, Ph_rx=-6
Sigma_i=286, Sigma_q=292, R_iq=-100
G_imb=2, Ph_rx=-2
RTMPSetPhyMode: channel is out of range, use first channel=0
MCS Set = ff ff 00 00 01
SYNC - BBP R4 to 20MHz.l
tSttttShell restarted.
0x80fd73f0 (tExcTask): 32 messages from interrupt level lost.

-> tShell restarted.

-> tShell restarted.

-> tShell restarted.

-> tShell restarted.

-> tShell restarted.

-> tShell restarted.

-> tShell restarted.

-> tShell restarted.

-> tShell restarted.

-> tShell restarted.

-> tShell restarted.

-> tShell restarted.

-> tShell restarted.

-> tShell restarted.

-> tShell restarted.

-> tShell restarted.

-> tShell restarted.

-> tShell restarted.

-> RTMP_TimerListAdd: add timer obj 80a99a78!
ADC clcok selection for E3 !!!
Shielding clock selection !!!
Main bssid = 1c:fa:68:f5:0a:5e
<==== rt28xx_init, Status=0
availableNum(0) devInitStr =0:4:0:1024:4:0:apcli
rt28xx_ap_ioctl():Not supported ioctl cmd:0x8004651d!
pAd->int_enable_reg=0x3fffc
Enrollee PinCode(ra0)           60148469
[ oal_wlan_openVap ] 1279:  Current addHver is 0x0

rt28xx_ap_ioctl():Not supported ioctl cmd:0xc00c6516!
rt28xx_ap_ioctl():Not supported ioctl cmd:0x40046514!
ra0 attach to br0 done!
rt28xx_ap_ioctl():Not supported ioctl cmd:0xc00c6516!
rt28xx_ap_ioctl():Not supported ioctl cmd:0x40046514!
apcli0 attach to br0 done!
[ msg_connSrv ] 269:  Can't connect server 8 and retry

[ msg_connSrv ] 269:  Can't connect server 8 and retry

[ msg_connSrv ] 269:  Can't connect server 8 and retry

[ msg_connSrv ] 269:  Can't connect server 8 and retry

mem_initPool is been called: malloc 60*64 (0x80851a30 - 0x80852930)
[ msg_connSrv ] 269:  Can't connect server 9 and retry

tc_core_init(): psched_tick_per_us=983040 psched_us_per_tick=1000000    clock_factor=1.000000 tick_in_used=0.983040
HTB ROOT QDISC:  size=1232
+ HTB CLASS:  size=98832
tc_htb_init:  addr=0x8082d100  endAddr=0x80845310  rootqNum=2  classMaxNum=40
SFQ QDISC:  size=129880
tc_sfq_init:  addr=0x8080d590  endAddr=0x8082d0e8  ruleNum=34
PFIFO QDISC:  size=1000
tc_fifo_init:  addr=0x8080d190  endAddr=0x8080d578  ruleNum=10
FW FILTER:  size=1728
tc_fw_init:  addr=0x8080cac0  endAddr=0x8080d180  num=36
Cannot find the device which name is eth1!
no interface name: eth1 found!
ifMgr_setIfDown(): Get interface failed!
[ oal_intf_disableIntf ] 238:  Disable interface eth1 failed!
set mii port 0 value 0x00003100
no interface name: eth1 found!
ifMgr_ifIsUp(): Get interface failed!
[ oal_wan_startL3Interface ] 564:  Start interface ppp0 (layer2 ifName=eth1)
no interface name: eth1 found!
no interface name: eth1 found!
Vlan ID 0 is wrong
ifMgr_setIfMac: Interface eth1 NOT been attach to ip stack yet!
[ oal_intf_enableIntf ] 211:  to enable interface eth1 !
pppLoad():pDrvCtrl->name(ppp0).
pppAttach():pppObj->pDrvCtrl->name(ppp0).
pppAttach():pppObj initialization succeed.
add net default: gateway 169.254.113.2
username:[ msg_connSrv ] 269:  Can't connect server 13 and retry

alg_open(): OK 0
alg_open(): OK 5
delVpnRule() ERROR.
alg_open(): OK 1
delVpnRule() ERROR.
alg_open(): OK 3
delVpnRule() ERROR.
alg_open(): OK 2
Enable mt7620 PDMA!
????????????C
syntax error
->
->
->
->
我的恩山、我的无线 The best wifi forum is right here.
回复

使用道具 举报

发表于 2017-6-8 13:59 | 显示全部楼层
你的波特率设的多少??
我的恩山、我的无线 The best wifi forum is right here.
回复

使用道具 举报

发表于 2018-12-16 18:32 | 显示全部楼层
你波特率是多少?TX RX GND的定义?
我的恩山、我的无线 The best wifi forum is right here.
回复

使用道具 举报

发表于 2018-12-17 15:22 | 显示全部楼层
不如直接上编程器
我的恩山、我的无线 The best wifi forum is right here.
回复

使用道具 举报

发表于 2018-12-18 08:56 | 显示全部楼层
===>RtmpOSWrielessEventSend eventType=0x8c02
===>RtmpOSWrielessEventSend eventType=0x8c02
eth1 config done!
===>RtmpOSWrielessEventSend eventType=0x8c02
===>RtmpOSWrielessEventSend eventType=0x8c02
===>RtmpOSWrielessEventSend eventType=0x8c02
eth1 config done!
eth1 config done!
“===>RtmpOSWrielessEventSend eventType=0x8c02
===>RtmpOSWrielessEventSend eventType=0x8c02
===>RtmpOSWrielessEventSend eventType=0x8c02
eth1 config done!
eth1 config done!

我连上TTL,路由器通上电就是这个,没有其他的是怎么事?求指教……
我的恩山、我的无线 The best wifi forum is right here.
回复

使用道具 举报

发表于 2018-12-19 08:45 | 显示全部楼层
朋友解决了吗?我也是同样的问题……
我的恩山、我的无线 The best wifi forum is right here.
回复

使用道具 举报

发表于 2019-3-3 23:39 | 显示全部楼层
我拿去试试看
我的恩山、我的无线 The best wifi forum is right here.
回复

使用道具 举报

您需要登录后才可以回帖 登录 | 立即注册

本版积分规则

有疑问请添加管理员QQ86788181|手机版|小黑屋|Archiver|恩山无线论坛(常州市恩山计算机开发有限公司版权所有) ( 苏ICP备05084872号 )

GMT+8, 2024-3-28 16:48

Powered by Discuz! X3.5

© 2001-2024 Discuz! Team.

| 江苏省互联网有害信息举报中心 举报信箱:js12377 | @jischina.com.cn 举报电话:025-88802724 本站不良内容举报信箱:68610888@qq.com 举报电话:0519-86695797

快速回复 返回顶部 返回列表