|
楼主 |
发表于 2016-1-12 21:45
|
显示全部楼层
本帖最后由 youxiaojie 于 2016-1-12 21:46 编辑
U-Boot 1.1.4 (Mar 19 2013 - 15:19:42)
U-boot DB120
DRAM: 128 MB
id read 0x100000ff
flash size 8MB, sector count = 128
Flash: 8 MB
Using default environment
PCIe Reset OK!!!!!!
In: serial
Out: serial
Err: serial
Net: ag934x_enet_initialize...
No valid address in Flash. Using fixed address
wasp reset mask:c03300
WASP ----> S17 PHY *
: cfg1 0x7 cfg2 0x7114
eth0: ba:be:fa:ce:08:41
athrs17_reg_init: complete
eth0 up
eth0
Autobooting in 1 seconds
## Booting image at 9f020000 ...
Uncompressing Kernel Image ... OK
Starting kernel ...
AR9344
detect mem size
Uart Init
Booting WASP !!! - ...
[ 0.000000] Linux version 3.5.7-rc1-svn20118 (root@dd-wrt) (gcc version 4.7.2 20120910 (prerelease) (Linaro GCC 4.7-2012.09) ) #1669 Fri Oct 12 07:15:44 CEST 2012
[ 0.000000] flash_size passed from bootloader = 8
[ 0.000000] CPU revision is: 0001974c (MIPS 74Kc)
[ 0.000000] arch_mem_init
[ 0.000000] wasp_sys_frequency: cpu srif ddr srif cpu 560 ddr 450 ahb 225
[ 0.000000] sys id = 2122 Atheros AR9344 rev 1.2 (0x2122)
[ 0.000000] Determined physical RAM map:
[ 0.000000] memory: 08000000 @ 00000000 (usable)
[ 0.000000] Zone ranges:
[ 0.000000] Normal [mem 0x00000000-0x07ffffff]
[ 0.000000] Movable zone start for each node
[ 0.000000] Early memory node ranges
[ 0.000000] node 0: [mem 0x00000000-0x07ffffff]
[ 0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
[ 0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 32512
[ 0.000000] Kernel command line: console=ttyS0,115200 root=1f02 rootfstype=squashfs noinitrd init=/sbin/init
[ 0.000000] PID hash table entries: 512 (order: -1, 2048 bytes)
[ 0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
[ 0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
[ 0.000000] __ex_table already sorted, skipping sort
[ 0.000000] Writing ErrCtl register=00000000
[ 0.000000] Readback ErrCtl register=00000000
[ 0.000000] Memory: 126772k/131072k available (2253k kernel code, 4300k reserved, 435k data, 168k init, 0k highmem)
[ 0.000000] NR_IRQS:80
[ 0.060000] Calibrating delay loop... 278.93 BogoMIPS (lpj=1394688)
[ 0.060000] pid_max: default: 32768 minimum: 301
[ 0.070000] Mount-cache hash table entries: 512
[ 0.070000] NET: Registered protocol family 16
[ 0.270000] init ar934x wmac
[ 0.480000] registering PCI controller with io_map_base unset
[ 0.490000] bio: create slab <bio-0> at 0
[ 0.490000] PCI host bridge to bus 0000:00
[ 0.490000] pci_bus 0000:00: root bus resource [mem 0x10000000-0x17ffffff]
[ 0.490000] pci_bus 0000:00: root bus resource [io 0x0000]
[ 0.490000] pci 0000:00:00.0: fixup device configuration
[ 0.490000] bootstrap returns device 168C:33
[ 0.490000] pci 0000:00:00.0: BAR 0: assigned [mem 0x10000000-0x1001ffff 64bit]
[ 0.490000] pci 0000:00:00.0: BAR 6: assigned [mem 0x10020000-0x1002ffff pref]
[ 0.490000] PCI: mapping irq 72 to pin1@0000:00:00.0
[ 0.490000] Switching to clocksource MIPS
[ 0.490000] NET: Registered protocol family 2
[ 0.500000] IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.500000] TCP established hash table entries: 4096 (order: 3, 32768 bytes)
[ 0.500000] TCP bind hash table entries: 4096 (order: 2, 16384 bytes)
[ 0.500000] TCP: Hash tables configured (established 4096 bind 4096)
[ 0.500000] TCP: reno registered
[ 0.500000] UDP hash table entries: 256 (order: 0, 4096 bytes)
[ 0.500000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[ 0.500000] NET: Registered protocol family 1
[ 0.500000] gpio_proc: module loaded and /proc/gpio/ created
[ 0.500000] wl0gpio_proc: module loaded and /proc/wl0gpio/ created
[ 0.500000] squashfs: version 3.0 (2006/03/15) Phillip Lougher
[ 0.500000] msgmni has been set to 247
[ 0.500000] io scheduler noop registered
[ 0.500000] io scheduler deadline registered (default)
[ 0.500000] Serial: 8250/16550 driver, 1 ports, IRQ sharing disabled
[ 0.510000] serial8250.0: ttyS0 at MMIO 0x18020000 (irq = 11) is a 16550A
[ 0.840000] console [ttyS0] enabled
[ 0.850000] guessed flashsize = 8M
[ 0.850000] scanning for root partition
[ 0.850000] tplink uboot detected
[ 0.860000] guessed bootloader size = 20000
[ 0.860000]
[ 0.860000] found squashfs at 130000
[ 0.870000] Creating 8 MTD partitions on "ar7240-nor0":
[ 0.870000] 0x000000000000-0x000000020000 : "RedBoot"
[ 0.880000] 0x000000020000-0x0000007e0000 : "linux"
[ 0.890000] 0x000000130000-0x0000006c0000 : "rootfs"
[ 0.890000] mtd: partition "rootfs" set to be root filesystem
[ 0.900000] 0x0000006c0000-0x0000007e0000 : "ddwrt"
[ 0.910000] 0x0000007e0000-0x0000007f0000 : "nvram"
[ 0.910000] 0x0000007f0000-0x000000800000 : "board_config"
[ 0.920000] 0x000000000000-0x000000800000 : "fullflash"
[ 0.930000] 0x000000000000-0x000000020000 : "fullboot"
[ 0.930000] Fixed MDIO Bus: probed
[ 0.940000] tun: Universal TUN/TAP device driver, 1.6
[ 0.940000] tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
[ 0.950000] PPP generic driver version 2.4.2
[ 0.950000] PPP BSD Compression module registered
[ 0.960000] PPP Deflate Compression module registered
[ 0.960000] PPP MPPE Compression module registered
[ 0.970000] NET: Registered protocol family 24
[ 0.980000] u32 classifier
[ 0.990000] Performance counters on
[ 0.990000] input device check on
[ 1.000000] Actions configured
[ 1.000000] Netfilter messages via NETLINK v0.30.
[ 1.000000] nf_conntrack version 0.5.0 (1980 buckets, 7920 max)
[ 1.010000] nf_conntrack_rtsp v0.6.21 loading
[ 1.010000] nf_nat_rtsp v0.6.21 loading
[ 1.020000] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 1.020000] IPP2P v0.8.2 loading
[ 1.030000] TCP: westwood registered
[ 1.030000] TCP: hybla registered
[ 1.030000] TCP: vegas registered
[ 1.040000] NET: Registered protocol family 17
[ 1.040000] Bridge firewalling registered
[ 1.050000] 8021q: 802.1Q VLAN Support v1.8
[ 1.050000] searching for nvram
[ 1.060000] nvram size = 0
[ 1.080000] Atheros AR71xx hardware watchdog driver version 0.1.0
[ 1.090000] ar71xx-wdt: timeout=15 secs (max=107) ref freq=40000000
[ 1.100000] VFS: Mounted root (squashfs filesystem) readonly on device 31:2.
[ 1.110000] Freeing unused kernel memory: 168k freed
start service
starting Architecture code for wasp
starting hotplug
Jan 1 00:00:02 udevtrigger[245]: parse_config_file: can't open '/etc/udev/udev.conf' as config file: No such file or directory
done
load ATH Ethernet Driver
[ 4.060000] ag71xx_mdio: probed
[ 4.070000] eth0: Atheros AG71xx at 0xb9000000, irq 4
[ 4.740000] eth0: Atheros AR8327 switch driver attached.
[ 6.450000] ag71xx ag71xx.0: eth0: connected to PHY at ag71xx-mdio.0:00 [uid=004dd034, driver=Atheros AR8216/AR8236/AR8316]
load ATH 802.11 a/b/g Driver
load ATH9K 802.11n Driver
[ 7.620000] Compat-drivers backport release: compat-drivers-2012-09-04-2-gddac993
[ 7.630000] Backport based on wireless-testing.git master-2012-09-07
[ 7.630000] compat.git: wireless-testing.git
[ 7.770000] cfg80211: Calling CRDA to update world regulatory domain
[ 8.050000] cfg80211: World regulatory domain updated:
[ 8.060000] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
[ 8.070000] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 8.070000] cfg80211: (2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[ 8.080000] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[ 8.090000] cfg80211: (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 8.100000] cfg80211: (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 8.360000] ieee80211 phy0: Atheros AR9340 Rev:0 mem=0xb8100000, irq=78
[ 8.380000] ieee80211 phy1: Atheros AR9300 Rev:4 mem=0xb0000000, irq=72
[ 8.390000] cfg80211: Calling CRDA for country: US
[ 8.510000] cfg80211: Regulatory domain changed to country: US
[ 8.510000] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
[ 8.520000] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2700 mBm)
[ 8.530000] cfg80211: (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 1700 mBm)
[ 8.540000] cfg80211: (5250000 KHz - 5330000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 8.540000] cfg80211: (5490000 KHz - 5600000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 8.550000] cfg80211: (5650000 KHz - 5710000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 8.560000] cfg80211: (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 3000 mBm)
[USB] checking...
[ 8.860000] usbcore: registered new interface driver usbfs
[ 8.870000] usbcore: registered new interface driver hub
[ 8.870000] usbcore: registered new device driver usb
[ 8.940000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 8.990000] ar71xx-ehci ar71xx-ehci.0: Atheros AR91xx built-in EHCI controller
[ 9.000000] ar71xx-ehci ar71xx-ehci.0: new USB bus registered, assigned bus number 1
[ 9.010000] ehci_reset Intialize USB CONTROLLER in host mode: 13
[ 9.010000] ehci_reset Port Status 1c000000
[ 9.050000] ar71xx-ehci ar71xx-ehci.0: irq 3, io mem 0x1b000000
[ 9.070000] ar71xx-ehci ar71xx-ehci.0: USB 2.0 started, EHCI 1.00
[ 9.070000] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
[ 9.080000] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 9.090000] usb usb1: Product: Atheros AR91xx built-in EHCI controller
[ 9.090000] usb usb1: Manufacturer: Linux 3.5.7-rc1-svn20118 ehci_hcd
[ 9.100000] usb usb1: SerialNumber: platform
[ 9.100000] switch USB LED Off
[ 9.11000ath9k deconfigure_single: phy0 ath0
ath9k deconfigure_single: phy1 ath1
/bin/sh: ead: not found
ath9k deconfigure_single: phy0 ath0
ath9k deconfigure_single: phy1 ath1
ath9k configure_single: phy0 ath0
call mac80211autochannel for interface: ath0
freq:2412 qual:86 noise:-84
freq:2417 qual:36 noise:-84
freq:2422 qual:73 noise:-89
freq:2427 qual:70 noise:-89
freq:2432 qual:34 noise:-89
freq:2437 qual:61 noise:-88
freq:2442 qual:41 noise:-89
freq:2447 qual:65 noise:-88
freq:2452 qual:71 noise:-88
freq:2457 qual:48 noise:-88
freq:2462 qual:98 noise:-88
mac80211autochannel interface: ath0 frequency: 2462
setup ath0 C0:61:18:FC:B8:9B
ath9k configure_single: phy1 ath1
call mac80211autochannel for interface: ath1
freq:5180 qual:96 noise:-89
freq:5200 qual:96 noise:-89
freq:5220 qual:94 noise:-88
freq:5240 qual:92 noise:-87
freq:5260 qual:90 noise:-86
freq:5280 qual:90 noise:-86
freq:5300 qual:88 noise:-85
freq:5320 qual:86 noise:-84
freq:5500 qual:86 noise:-84
freq:5520 qual:88 noise:-85
freq:5540 qual:88 noise:-85
freq:5560 qual:88 noise:-85
freq:5580 qual:88 noise:-85
freq:5660 qual:88 noise:-85
freq:5680 qual:90 noise:-86
freq:5700 qual:92 noise:-87
freq:5745 qual:96 noise:-89
freq:5755 qual:96 noise:-89
freq:5760 qual:98 noise:-90
freq:5765 qual:96 noise:-89
freq:5770 qual:98 noise:-90
freq:5775 qual:98 noise:-90
freq:5780 qual:98 noise:-90
freq:5785 qual:98 noise:-90
freq:5790 qual:98 noise:-90
freq:5795 qual:98 noise:-90
freq:5800 qual:98 noise:-90
freq:5805 qual:98 noise:-90
freq:5810 qual:98 noise:-90
freq:5815 qual:100 noise:-91
freq:5820 qual:98 noise:-90
freq:5825 qual:100 noise:-91
mac80211autochannel interface: ath1 frequency: 5815
setup ath1 C0:61:18:FC:B8:9C
svqos: No such file or directory
svqos: No such file or directory
svqos: No such file or directory
svqos: No such file or directory
telnetd: No such file or directory
cron: No such file or directory
ath9k radio 1: phy0 ath0
ath9k radio 1: phy1 ath1
The Milkfish Router Services
ERROR: Necessary service setting not found: milkfish_username - aborting.
The Milkfish Router Services
Restoring SIP ddsubscriber database from NVRAM...
Empty.
The Milkfish Router Services
Restoring SIP ddaliases database from NVRAM...
Empty.
: onfactory init wait until network establish
bootargs=console=ttyS0,115200 root=31:02 rootfstype=squashfs init=/sbin/init mtdparts=ath-nor0:256k(u-boot),64k(u-boot-env),6336k(rootfs),1408k(uImage),64k(mib0),64k(ART)
bootcmd=bootm 0x9f020000
bootdelay=1
baudrate=115200
ethaddr=0xba:0xbe:0xfa:0xce:0x08:0x41
ipaddr=192.168.1.111
serverip=192.168.1.100
dir=
lu=tftp 0x80060000 ${dir}u-boot.bin&&erase 0x9f000000 +$filesize;cp.b $fileaddr 0x9f000000 $filesize
lf=tftp 0x80060000 ${dir}db12x${bc}-jffs2&&erase 0x9f050000 +0x630000;cp.b $fileaddr 0x9f050000 $filesize
lk=tftp 0x80060000 ${dir}vmlinux${bc}.lzma.uImage&&erase 0x9f680000 +$filesize;cp.b $fileaddr 0x9f680000 $filesize
stdin=serial
stdout=serial
stderr=serial
ethact=eth0
Environment size: 686/65532 bytes
db12x> md
Usage:
md - memory display
在这些分区里面,
[ 0.870000] Creating 8 MTD partitions on "ar7240-nor0":
[ 0.870000] 0x000000000000-0x000000020000 : "RedBoot"
[ 0.880000] 0x000000020000-0x0000007e0000 : "linux"
[ 0.890000] 0x000000130000-0x0000006c0000 : "rootfs"
[ 0.890000] mtd: partition "rootfs" set to be root filesystem
[ 0.900000] 0x0000006c0000-0x0000007e0000 : "ddwrt"
[ 0.910000] 0x0000007e0000-0x0000007f0000 : "nvram"
[ 0.910000] 0x0000007f0000-0x000000800000 : "board_config"
[ 0.920000] 0x000000000000-0x000000800000 : "fullflash"
[ 0.930000] 0x000000000000-0x000000020000 : "fullboot"
分区里面那个是art数据?redboot又是什么? |
|