K2信号接近官方的潘多拉版本为小米r1055

kesunji

小长假在家带娃，顺便测试了手上K2能用的潘多拉固件和华硕固件信号情况，因为华硕固件无法多拨，只测试了自动免费fan wall楼主推荐的RT-AC54U-GPIO-1-PSG1208-64M_3.4.3.9-099.trx之后就没多测试了。

结果很吃惊，测试的华硕版本完全没有打开PA，2.4G和5G信号都弱得很，直接放弃。最奇怪的是，网上众多人推荐的PandoraBox-ralink-mt7620-phicomm-k1-squashfs-sysupgrade-r2075-20160203这个号称K1专用版本，虽然在K2上表现2.4G信号很强，而且驱动正确读到EEPROM重要开启外置LNA，但似乎驱动打开了内置的PA，导致两个PA串联（所以信号强），但信号过强反而导致数据无法传输，2.4G Throughput很低，最可怕的是5G上面，用两个2x2AC网卡的手机或电脑挂上测试Throughput，速度上不去不说，还经常断线，链接速度直接变成6Mbps，就再也上不去网了。

有关这个固件我还专门用K1也测试了一下，发现结果一样，2.4G速度不高，5G高速断线，看来潘多拉的新版本闭源驱动还很不稳定，希望大家不要在用这个K1专用潘多拉固件了。


因为官网上潘多拉固件很多，我只测试了部分OYE的固件和烧进去能正常跑的小米固件（大小不超过7MB的固件，7.5MB的固件跑起来会有各种错误）

最后确认了使用3.0.3.2驱动的潘多拉固件从远近距离信号强度，远近距离传输速率，远距离连接成功率等几个方面都跟原厂固件差不多，这版驱动没有太多打印信息，但从实际效果来看，应该正常的打开了PA和LNA，用相同的这个固件，K2比K1在双频都强3-5db，跟K2官方固件几乎信号幅度完全相等，所以不用再担心烧PA了！进一步我明天到公司跟同事的原装固件Sidebyside做个对比，我相信跟我来回烧写固件得到的结果差不多。

另外，还有个帅哥自己修改DTS文件并编译了打开PA的K2固件，这个固件信号很强，我猜也是没关内置PA，所以2.4G网速很慢，据说把信号强度调到0就好了，但我希望最后闭源驱动也能找到关闭内置PA的办法，方便大家玩机！

最后也求助大家个事请，是否有人有使用3.0.3.2这版本驱动的带有SS的潘多拉固件？因为不想拆机换Flash，小米和OYE的固件中都集成了很多USB的东东，太占地方了，所以我找到的固件中都没有SS，如果大家手上有相同驱动，且带有多拨的其他精简版本固件，还请提供给我，我就不瞎折腾了，另外一个哥们搞的免费fan wall还挺有意思，就是脚本的稳定性和兼容性还有待提高，昨天费了我不少劲，还是没完全搞好。

附上官方固件下载地址，祝大家K2玩儿的开心！

http://downloads.openwrt.org.cn/ ... -r1055-20150615.bin

版本信息：
主机型号 Xiaomi mini Board 固件版本 PandoraBox R2 14.09 / LuCI Trunk (0.12+svn-r1055) 内核版本 3.14.44

驱动版本信息命令行输入 kmesg |grep Driver   回车即可查看)
[   15.330000] PandoraBox RT2860v2 AP Driver version-3.0.3.2(Jun 15 2015 15:02:58).
[   15.830000] PandoraBox MT76X2E AP Driver version-3.0.3.2(Jun 15 2015 14:33:14).

更新：今天用同事的原厂固件盒子放在边上用远近两种距离对比，发现确实两种固件信号强度非常相近（排除不规则的波动）。

tom663

顶下楼主！

kesunji

更新一下信息，那个K1专用版使用的应该是3.0.4.2这个驱动，我尝试了将信号强度改为1%，确实2.4G速度就能上去了，5G断流的问题我没试，5G这边信号强度调弱后，信号强度就真的减弱了，这个驱动本来原始5G信号就不行，弱了就更没用了。


   16.880000] PandoraBox MT76x2E AP Driver version-3.0.4.2.P1(Nov 22 2015 16:16:21).
[   16.890000] RtmpOSFileOpen(): Error 2 opening /etc/Wireless/MT76X2/MT7612.dat
[   16.890000] Open file "/etc/Wireless/MT76X2/MT7612.dat" failed!
[   16.900000] ###########################################
[   16.910000] ###########################################
[   16.910000] Read Parameters from default_profile_buffer
[   16.920000] ###########################################
[   16.920000] ###########################################
[   16.930000] cfg_mode=9
[   16.930000] cfg_mode=9
[   16.930000] wmode_band_equal(): Band Not Equal!
[   16.940000] APSDCapable[0]=0
[   16.950000] APSDCapable[1]=0
[   16.950000] APSDCapable[2]=0
[   16.950000] APSDCapable[3]=0
[   16.950000] APSDCapable[4]=0
[   16.960000] APSDCapable[5]=0
[   16.960000] APSDCapable[6]=0
[   16.960000] APSDCapable[7]=0
[   16.970000] APSDCapable[8]=0
[   16.970000] APSDCapable[9]=0
[   16.970000] APSDCapable[10]=0
[   16.980000] APSDCapable[11]=0
[   16.980000] APSDCapable[12]=0
[   16.980000] APSDCapable[13]=0
[   16.980000] APSDCapable[14]=0
[   16.990000] APSDCapable[15]=0
[   16.990000] default ApCliAPSDCapable[0]=0
[   17.000000] Key1Str is Invalid key length(0) or Type(0)
[   17.000000] Key2Str is Invalid key length(0) or Type(0)
[   17.010000] Key3Str is Invalid key length(0) or Type(0)
[   17.020000] Key4Str is Invalid key length(0) or Type(0)
[   17.040000] RtmpChipOpsEepromHook::e2p_type=0, inf_Type=5
[   17.050000] RtmpEepromGetDefault::e2p_dafault=2
[   17.050000] NVM is efuse and the information is too less to bring up the interface
[   17.060000] Force to use Flash mode
[   17.060000] NVM is FLASH mode (pAd->flash_offset = 0x48000)
[   17.070000] get_dev_name_prefix(): dev_idx = 1, dev_name_prefix=rai
[   17.090000] ===> rt2880_probe
[   17.100000]
[   17.100000]
[   17.100000] === pAd = c08bd000, size = 2336328 ===
[   17.100000]
[   17.110000] <-- RTMPAllocTxRxRingMemory, Status=0
[   17.120000] <-- RTMPAllocAdapterBlock, Status=0
[   17.120000] PandoraBox MT7620 AP Driver version-3.0.4.2.P1(Nov 22 2015 16:16:21).
[   17.130000] RtmpOSFileOpen(): Error 2 opening /etc/Wireless/RT2860/RT2860.dat
[   17.140000] Open file "/etc/Wireless/RT2860/RT2860.dat" failed!
[   17.140000] ###########################################
[   17.150000] ###########################################
[   17.160000] Read Parameters from default_profile_buffer
[   17.160000] ###########################################
[   17.170000] ###########################################
[   17.170000] cfg_mode=9
[   17.180000] cfg_mode=9
[   17.180000] wmode_band_equal(): Band Not Equal!
[   17.190000] APSDCapable[0]=0
[   17.190000] APSDCapable[1]=0
[   17.190000] APSDCapable[2]=0
[   17.190000] APSDCapable[3]=0
[   17.200000] APSDCapable[4]=0
[   17.200000] APSDCapable[5]=0
[   17.200000] APSDCapable[6]=0
[   17.210000] APSDCapable[7]=0
[   17.210000] APSDCapable[8]=0
[   17.210000] APSDCapable[9]=0
[   17.210000] APSDCapable[10]=0
[   17.220000] APSDCapable[11]=0
[   17.220000] APSDCapable[12]=0
[   17.220000] APSDCapable[13]=0
[   17.230000] APSDCapable[14]=0
[   17.230000] APSDCapable[15]=0
[   17.230000] default ApCliAPSDCapable[0]=0
[   17.240000] Key1Str is Invalid key length(0) or Type(0)
[   17.250000] Key2Str is Invalid key length(0) or Type(0)
[   17.250000] Key3Str is Invalid key length(0) or Type(0)
[   17.260000] Key4Str is Invalid key length(0) or Type(0)
[   17.280000] RtmpChipOpsEepromHook::e2p_type=0, inf_Type=4
[   17.290000] RtmpEepromGetDefault::e2p_dafault=2
[   17.290000] NVM is FLASH mode (pAd->flash_offset = 0x40000)
[   17.300000] get_dev_name_prefix(): dev_idx = 0, dev_name_prefix=ra
[   17.370000] ra0: at CSR addr 0xb0180000, IRQ 4.
[   17.370000] <=== rt2880_probe
[   17.380000] ip_tables: (C) 2000-2006 Netfilter Core Team, NAT Type:Symmetric Cone
[   17.420000] xt_time: kernel timezone is -0000
[   17.430000] PPP generic driver version 2.4.2
[   17.440000] NET: Registered protocol family 24
[   24.090000] procd: - init complete -
[   26.080000] IPv6: ADDRCONF(NETDEV_UP): lo: link is not ready
[   26.120000] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[   26.160000] raeth: frame engine reset
[   26.160000] raeth: PDMA init
[   26.170000] No PHY connected on GE1
[   26.170000] No PHY connected on GE2
[   26.180000] raeth: HW VLAN TX offload enabled
[   26.190000] raeth: HW IP/TCP/UDP checksum RX/TX offload enabled
[   26.190000] raeth: NAPI POLL mode enabled
[   26.200000] raeth: NAPI GRO offload enabled
[   26.200000] raeth: HW Scatter/Gather TX offload enabled
[   26.210000] raeth: HW TCP segmentation offload (TSO) enabled
[   26.220000] device eth0.1 entered promiscuous mode
[   26.220000] device eth0 entered promiscuous mode
[   26.250000] br-lan: port 1(eth0.1) entered forwarding state
[   26.250000] br-lan: port 1(eth0.1) entered forwarding state
[   27.730000] MT76x2E:load patch [mt7662_patch_hdr.bin] from /lib/firmware/
[   27.960000] build time = [20141115060606a
[   27.960000] ]
[   27.960000] rom patch for E3 IC
[   27.960000] platform = [ALPS]
[   27.970000] hw/sw version = [8a 10 8a 10 ]
[   27.970000] patch version = [00000010]
[   27.990000] MT76x2E:load Firmware [mt7662_firmware.bin] from /lib/firmware/
[   28.020000] FW Version:0.0.00 Build:1
[   28.020000] Build Time:201511101431____
[   28.030000] fw for E3 IC
[   28.030000] EEPROM:Read from [Factory] offset 0x8000,length 0x200.
[   28.050000] RX[0] DESC a3373000 size = 4096
[   28.060000] RX[1] DESC a3374000 size = 4096
[   28.120000] cfg_mode=14
[   28.130000] cfg_mode=14
[   28.130000] wmode_band_equal(): Band Not Equal!
[   28.140000] APSDCapable[0]=0
[   28.140000] APSDCapable[1]=0
[   28.150000] APSDCapable[2]=0
[   28.150000] APSDCapable[3]=0
[   28.150000] APSDCapable[4]=0
[   28.160000] APSDCapable[5]=0
[   28.160000] APSDCapable[6]=0
[   28.160000] APSDCapable[7]=0
[   28.160000] APSDCapable[8]=0
[   28.170000] APSDCapable[9]=0
[   28.170000] APSDCapable[10]=0
[   28.170000] APSDCapable[11]=0
[   28.180000] APSDCapable[12]=0
[   28.180000] APSDCapable[13]=0
[   28.180000] APSDCapable[14]=0
[   28.190000] APSDCapable[15]=0
[   28.190000] default ApCliAPSDCapable[0]=0
[   28.240000] 1. Phy Mode = 49
[   28.250000] br-lan: port 1(eth0.1) entered forwarding state
[   28.250000] EEPROM:Read from [Factory] offset 0x8000,length 0x200.
[   28.260000] get_chl_grp:illegal channel (167)
[   28.260000] get_chl_grp:illegal channel (167)
[   28.270000] get_chl_grp:illegal channel (169)
[   28.270000] get_chl_grp:illegal channel (169)
[   28.280000] get_chl_grp:illegal channel (171)
[   28.280000] get_chl_grp:illegal channel (171)
[   28.290000] /home/user/src/pandorabox-14.09/build_dir/target-mipsel_24kec+dsp_uClibc-0.9.33.2/linux-ralink_mt7620/mt76x2e/rlt_wifi_ap//../rlt_wifi/chips/mt76x2.c:2847 assert (ad->TxPower[choffset].Channel == 42)failed
[   28.310000] Country Region from e2p = ffff
[   28.310000] mt76x2_read_temp_info_from_eeprom:: is_temp_tx_alc=0, temp_tx_alc_enable=0
[   28.320000] mt76x2_read_tx_alc_info_from_eeprom:: is_ePA_mode=1, ePA_type=1
[   28.320000] mt76x2_read_tx_alc_info_from_eeprom:: [5G band] high_temp_slope=15, low_temp_slope=9
[   28.330000] mt76x2_read_tx_alc_info_from_eeprom:: [2G band] high_temp_slope=0, low_temp_slope=0
[   28.340000] mt76x2_read_tx_alc_info_from_eeprom:: [5G band] tc_lower_bound=-7, tc_upper_bound=4
[   28.350000] mt76x2_read_tx_alc_info_from_eeprom:: [2G band] tc_lower_bound=0, tc_upper_bound=0
[   28.360000] mt76x2_get_external_lna_gain:NA type=0x1, BLNAGain=0xffffff8c, ALNAGain0=0xffffff8f, ALNAGain1=0xffffff8f, ALNAGain2=0xffffff8f
[   28.370000] 2. Phy Mode = 49
[   28.380000] 3. Phy Mode = 49
[   28.380000] andes_pci_fw_init
[   28.380000] 0x1300 = 00073200
[   28.410000] AntCfgInit: primary/secondary ant 0/1
[   28.420000] andes_load_cr:cr_type(2)
[   28.430000] ChipStructAssign(): MT76x2 hook !
[   28.430000] MCS Set = ff ff 00 00 01
[   28.440000] mt76x2_bbp_adjust():rf_bw=2, ext_ch=1, PrimCh=157, HT-CentCh=159, VHT-CentCh=155
[   28.530000] APStartUp(): AP Set CentralFreq at 155(Prim=157, HT-CentCh=159, VHT-CentCh=155, BBP_BW=2)
[   28.550000] mt76x2_calibration(channel = 155)
[   28.920000] Main bssid = 8c:ab:8e:8c:0e:e0
[   28.930000] mt76x2_reinit_agc_gainriginal agc_vga0 = 0x42, agc_vga1 = 0x42
[   28.930000] mt76x2_reinit_agc_gain:updated agc_vga0 = 0x42, agc_vga1 = 0x42
[   28.940000] mt76x2_reinit_hi_lna_gainriginal hi_lna0 = 0x36, hi_lna1 = 0x36
[   28.950000] mt76x2_reinit_hi_lna_gain:updated hi_lna0 = 0x36, hi_lna1 = 0x36
[   28.960000] original vga value(chain0) = 42
[   28.960000] eth0: port 4 link up (100Mbps/Full duplex)
[   28.970000] original vga value(chain1) = 42
[   28.970000] <==== rt28xx_init, Status=0
[   28.970000] get_dev_name_prefix(): dev_idx = 1, dev_name_prefix=rai
[   29.020000] eth0: port 4 link down
[   29.130000] get_dev_name_prefix(): dev_idx = 1, dev_name_prefix=rai
[   29.140000] get_dev_name_prefix(): dev_idx = 1, dev_name_prefix=rai
[   29.150000] get_dev_name_prefix(): dev_idx = 1, dev_name_prefix=wdsi
[   29.160000] get_dev_name_prefix(): dev_idx = 1, dev_name_prefix=wdsi
[   29.170000] get_dev_name_prefix(): dev_idx = 1, dev_name_prefix=wdsi
[   29.190000] get_dev_name_prefix(): dev_idx = 1, dev_name_prefix=wdsi
[   29.210000] get_dev_name_prefix(): dev_idx = 1, dev_name_prefix=apclii
[   29.220000] MT76x2E Fast Mode init.
[   29.220000] RTMPDrvOpen(1):Check if PDMA is idle!
[   29.220000] RTMPDrvOpen(2):Check if PDMA is idle!
[   29.430000] device rai0 entered promiscuous mode
[   29.440000] br-lan: port 2(rai0) entered forwarding state
[   29.440000] br-lan: port 2(rai0) entered forwarding state
[   29.570000] RX[0] DESC a24f4000 size = 4096
[   29.610000] cfg_mode=9
[   29.620000] cfg_mode=9
[   29.620000] wmode_band_equal(): Band Equal!
[   29.630000] APSDCapable[0]=0
[   29.630000] APSDCapable[1]=0
[   29.630000] APSDCapable[2]=0
[   29.640000] APSDCapable[3]=0
[   29.640000] APSDCapable[4]=0
[   29.640000] APSDCapable[5]=0
[   29.650000] APSDCapable[6]=0
[   29.650000] APSDCapable[7]=0
[   29.650000] APSDCapable[8]=0
[   29.650000] APSDCapable[9]=0
[   29.660000] APSDCapable[10]=0
[   29.660000] APSDCapable[11]=0
[   29.660000] APSDCapable[12]=0
[   29.670000] APSDCapable[13]=0
[   29.670000] APSDCapable[14]=0
[   29.670000] APSDCapable[15]=0
[   29.680000] default ApCliAPSDCapable[0]=0
[   29.730000] 1. Phy Mode = 14
[   29.730000] EEPROM:Read from [Factory] offset 0x0,length 0x200.
[   29.740000] Country Region from e2p = ffff
[   29.740000] E2PROM: D0 target power=0xff20
[   29.750000] E2PROM: 40 MW Power Delta= 0
[   29.750000] 2. Phy Mode = 14
[   29.750000] 3. Phy Mode = 14
[   29.760000] AntCfgInit: primary/secondary ant 0/1
[   29.760000] D1 = -1, D2 = -1, CalCode = 0 !!!
[   29.770000] RT6352_Temperature_Init : BBPR49 = 0xfffffffe
[   29.780000] RT6352_Temperature_Init : TemperatureRef25C = 0xfffffff4
[   29.780000] Current Temperature from BBP_R49=0xfffffff1
[   29.790000]  TX BW Filter Calibration !!!
[   29.930000]  RX BW Filter Calibration !!!
[   30.190000] LOFT Calibration Done!
[   30.190000] IQCalibration Start!
[   30.210000] IQCalibration Done! CH = 0, (gain= e, phase= 2)
[   30.210000] IQCalibration Start!
[   30.230000] IQCalibration Done! CH = 1, (gain= d, phase=3e)
[   30.230000] TX IQ Calibration Done!
[   30.270000] Change as Normal Mode(0x48361d)
[   30.280000] After Change, now GPIO_MODE value is 0x48361d
[   30.280000] RT6352_Init_ExtPA_ExtLNA: Enable Ext-LNA.
[   30.290000] RT6352_Init_ExtPA_ExtLNA: Init Ext-LNA BBP.
[   30.300000] ChipStructAssign(): RALINK6352 hook !
[   30.300000] MCS Set = ff ff 00 00 01
[   30.340000] APStartUp(): AP Set CentralFreq at 3(Prim=1, HT-CentCh=3, VHT-CentCh=0, BBP_BW=1)
[   30.350000] Main bssid = 8c:ab:8e:8c:0e:d8
[   30.350000] <==== rt28xx_init, Status=0
[   30.360000] get_dev_name_prefix(): dev_idx = 0, dev_name_prefix=ra
[   30.780000] get_dev_name_prefix(): dev_idx = 0, dev_name_prefix=ra
[   30.800000] get_dev_name_prefix(): dev_idx = 0, dev_name_prefix=ra
[   30.800000] get_dev_name_prefix(): dev_idx = 0, dev_name_prefix=wds
[   30.840000] get_dev_name_prefix(): dev_idx = 0, dev_name_prefix=wds
[   30.840000] get_dev_name_prefix(): dev_idx = 0, dev_name_prefix=wds
[   30.880000] get_dev_name_prefix(): dev_idx = 0, dev_name_prefix=wds
[   30.880000] get_dev_name_prefix(): dev_idx = 0, dev_name_prefix=apcli
[   30.920000] MT76x2E Fast Mode init.
[   30.920000] RTMPDrvOpen(1):Check if PDMA is idle!
[   30.930000] RTMPDrvOpen(2):Check if PDMA is idle!
[   31.110000] device ra0 entered promiscuous mode
[   31.120000] br-lan: port 3(ra0) entered forwarding state
[   31.120000] br-lan: port 3(ra0) entered forwarding state
[   31.440000] br-lan: port 2(rai0) entered forwarding state
[   31.680000] eth0: port 4 link up (100Mbps/Full duplex)
[   33.120000] br-lan: port 3(ra0) entered forwarding state
[  114.530000] Rcv Wcid(1) AddBAReq
[  114.530000] Start Seq = 000000e7
[  153.450000] eth0: port 4 link down
[  318.170000] PeerDelBATxAdaptTimeOut()
[  321.370000] Rcv Wcid(1) AddBAReq
[  321.370000] Start Seq = 00000057
[  397.220000] MT76x2E Fast Mode exit.
[  397.240000] br-lan: port 3(ra0) entered disabled state
[  397.580000] device ra0 left promiscuous mode
[  397.580000] br-lan: port 3(ra0) entered disabled state
[  398.010000] RX[0] DESC a24f4000 size = 4096
[  398.030000] cfg_mode=9
[  398.030000] cfg_mode=9
[  398.040000] wmode_band_equal(): Band Equal!
[  398.050000] APSDCapable[0]=0
[  398.050000] APSDCapable[1]=0
[  398.050000] APSDCapable[2]=0
[  398.060000] APSDCapable[3]=0
[  398.060000] APSDCapable[4]=0
[  398.060000] APSDCapable[5]=0
[  398.060000] APSDCapable[6]=0
[  398.070000] APSDCapable[7]=0
[  398.070000] APSDCapable[8]=0
[  398.070000] APSDCapable[9]=0
[  398.080000] APSDCapable[10]=0
[  398.080000] APSDCapable[11]=0
[  398.080000] APSDCapable[12]=0
[  398.090000] APSDCapable[13]=0
[  398.090000] APSDCapable[14]=0
[  398.090000] APSDCapable[15]=0
[  398.090000] default ApCliAPSDCapable[0]=0
[  398.150000] 1. Phy Mode = 14
[  398.150000] EEPROM:Read from [Factory] offset 0x0,length 0x200.
[  398.160000] Country Region from e2p = ffff
[  398.160000] E2PROM: D0 target power=0xff20
[  398.170000] E2PROM: 40 MW Power Delta= 0
[  398.170000] 2. Phy Mode = 14
[  398.170000] 3. Phy Mode = 14
[  398.180000] AntCfgInit: primary/secondary ant 0/1
[  398.180000] Change as GPIO Mode(0x58361d)
[  398.190000] D1 = 0, D2 = 0, CalCode = 0 !!!
[  398.190000] RT6352_Temperature_Init : BBPR49 = 0x0
[  398.200000] RT6352_Temperature_Init : TemperatureRef25C = 0xfffffff6
[  398.210000] Current Temperature from BBP_R49=0xfffffff7
[  398.220000]  TX BW Filter Calibration !!!
[  398.350000]  RX BW Filter Calibration !!!
[  398.610000] LOFT Calibration Done!
[  398.620000] IQCalibration Start!
[  398.630000] IQCalibration Done! CH = 0, (gain= e, phase= 1)
[  398.640000] IQCalibration Start!
[  398.650000] IQCalibration Done! CH = 1, (gain= 0, phase= 2)
[  398.660000] TX IQ Calibration Done!
[  398.690000] Change as Normal Mode(0x48361d)
[  398.700000] After Change, now GPIO_MODE value is 0x48361d
[  398.700000] RT6352_Init_ExtPA_ExtLNA: Enable Ext-LNA.
[  398.710000] RT6352_Init_ExtPA_ExtLNA: Init Ext-LNA BBP.
[  398.710000] ChipStructAssign(): RALINK6352 hook !
[  398.720000] MCS Set = ff ff 00 00 01
[  398.760000] APStartUp(): AP Set CentralFreq at 3(Prim=1, HT-CentCh=3, VHT-CentCh=0, BBP_BW=1)
[  398.770000] Main bssid = 8c:ab:8e:8c:0e:d8
[  398.770000] <==== rt28xx_init, Status=0
[  398.780000] MT76x2E Fast Mode init.
[  398.780000] RTMPDrvOpen(1):Check if PDMA is idle!
[  398.790000] RTMPDrvOpen(2):Check if PDMA is idle!
[  398.840000] device ra0 entered promiscuous mode
[  398.840000] br-lan: port 3(ra0) entered forwarding state
[  398.850000] br-lan: port 3(ra0) entered forwarding state
[  400.850000] br-lan: port 3(ra0) entered forwarding state
[  401.540000] Rcv Wcid(1) AddBAReq
[  401.550000] Start Seq = 0000006e
[  434.400000] da match,0x8cab8e8c0ed8
[  435.090000] update_associated_mac_entry(): Peer's PhyCap=>Mode:VHT, BW:80M

ming1054

楼主很用心

我是二毛

现在有人说固件和功放无关，所以k2的用k1的固件就行；
另有人说固件和功放有关，要有打开的内容，所以k2用k1固件信号没有原版好。。。

真是犹豫啊，，，，

kesunji

我是二毛 发表于 2016-4-4 16:07
现在有人说固件和功放无关，所以k2的用k1的固件就行；
另有人说固件和功放有关，要有打开的内容，所以k2用 ...

问题是MTK的驱动能否正确读取EEP里面的信息，目前看起来大部分非原厂的驱动都读不对。

我是二毛

kesunji 发表于 2016-4-4 16:44
问题是MTK的驱动能否正确读取EEP里面的信息，目前看起来大部分非原厂的驱动都读不对。

那就希望尽快能看到专属于k2的驱动出现了。。

yxf123

我的K2之前就刷的那个版本，刷着试试你这个版本怎么样

riddle

联想y1 1055不错。用过，灯，接口都正常，楼主可试下

stwu

pa是硬功放，就是信号放大器。

billking

我也觉得1055这个版本对支持有单独功放的7620比较好！

kesunji

stwu 发表于 2016-4-4 20:17
pa是硬功放，就是信号放大器。

PA要配置好，有些还要选通，还要跟驱动配合好。今天还发现个奇怪的现象，K1用这个1055固件如果功率开大，还不如功率50%的时候传输速率高。

corundum

顶下楼主！

helpit

看不懂，刘贴

liucl

K2刷了老毛子的华硕，唯一的感受就是5G频繁断线啊，简直没法用