恩山无线论坛

 找回密码
 立即注册

QQ登录

只需一步,快速开始

搜索
查看: 1407|回复: 4

编译16M固件启动不起来帮忙分析下

[复制链接]
发表于 2016-10-15 17:25 | 显示全部楼层 |阅读模式
[    0.360000] console [ttyS0] enabled
[    0.370000] bootconsole [early0] disabled
[    0.370000] bootconsole [early0] disabled
[    0.400000] m25p80 spi32766.0: found w25q128, expected s25fl064k
[    0.410000] m25p80 spi32766.0: w25q128 (16384 Kbytes)
[    0.420000] 4 ofpart partitions found on MTD device spi32766.0
[    0.440000] Creating 4 MTD partitions on "spi32766.0":
[    0.450000] 0x000000000000-0x000000030000 : "u-boot"
[    0.460000] 0x000000030000-0x000000040000 : "u-boot-env"
[    0.470000] 0x000000040000-0x000000050000 : "factory"
[    0.480000] 0x000000050000-0x000000fd0000 : "firmware"
[    0.640000] 2 uimage-fw partitions found on MTD device firmware
[    0.660000] 0x000000050000-0x0000001599cd : "kernel"
[    0.670000] 0x0000001599cd-0x000000fd0000 : "rootfs"
[    0.680000] mtd: device 5 (rootfs) set to be root filesystem
[    0.690000] 1 squashfs-split partitions found on MTD device rootfs
[    0.700000] 0x000000350000-0x000000fd0000 : "rootfs_data"
[    0.730000] ralink_soc_eth 10100000.ethernet eth0: ralink at 0xb0100000, irq 5
[    0.740000] rt2880_wdt 10000120.watchdog: Initialized
[    0.760000] TCP: cubic registered
[    0.760000] NET: Registered protocol family 17
[    0.770000] bridge: automatic filtering via arp/ip/ip6tables has been deprecated. Update your scripts to load br_netfilter if you need this.
[    0.800000] 8021q: 802.1Q VLAN Support v1.8
[    0.840000] VFS: Mounted root (squashfs filesystem) readonly on device 31:5.
[    0.850000] Freeing unused kernel memory: 180K (802f3000 - 80320000)
[    3.970000] init: Console is alive
[    3.980000] init: - watchdog -
[    7.000000] usbcore: registered new interface driver usbfs
[    7.010000] usbcore: registered new interface driver hub
[    7.020000] usbcore: registered new device driver usb
[    7.040000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[    7.050000] ehci-platform: EHCI generic platform driver
[    7.260000] phy phy-usbphy.0: remote usb device wakeup disabled
[    7.280000] phy phy-usbphy.0: UTMI 16bit 30MHz
[    7.280000] ehci-platform 101c0000.ehci: EHCI Host Controller
[    7.300000] ehci-platform 101c0000.ehci: new USB bus registered, assigned bus number 1
[    7.310000] ehci-platform 101c0000.ehci: irq 26, io mem 0x101c0000
[    7.350000] ehci-platform 101c0000.ehci: USB 2.0 started, EHCI 1.00
[    7.360000] hub 1-0:1.0: USB hub found
[    7.370000] hub 1-0:1.0: 1 port detected
[    7.380000] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[    7.400000] ohci-platform: OHCI generic platform driver
[    7.410000] ohci-platform 101c1000.ohci: Generic Platform OHCI controller
[    7.420000] ohci-platform 101c1000.ohci: new USB bus registered, assigned bus number 2
[    7.440000] ohci-platform 101c1000.ohci: irq 26, io mem 0x101c1000
[    7.510000] hub 2-0:1.0: USB hub found
[    7.520000] hub 2-0:1.0: 1 port detected
[    8.030000] init: - preinit -
[    9.340000] rt305x-esw 10110000.esw: link changed 0x00
[    9.660000] random: procd urandom read with 15 bits of entropy available
Press the [f] key and hit [enter] to enter failsafe mode
Press the [1], [2], [3] or [4] key and hit [enter] to select the debug level
[   13.560000] jffs2: notice: (299) jffs2_build_xattr_subsystem: complete building xattr subsystem, 0 of xdatum (0 unchecked, 0 orphan) and 0 of xref (0 dead, 0 orphan) found.
[   13.610000] mount_root: switching to jffs2 overlay
[   13.800000] procd: - early -
[   13.810000] procd: - watchdog -
[   14.940000] procd: - ubus -
启动信息,到这里就不动了
我的恩山、我的无线 The best wifi forum is right here.
 楼主| 发表于 2016-10-15 17:53 | 显示全部楼层
本帖最后由 fghlw 于 2016-10-15 18:27 编辑

[    0.360000] console [ttyS0] enabled
[    0.370000] bootconsole [early0] disabled
[    0.370000] bootconsole [early0] disabled
[    0.400000] m25p80 spi32766.0: found w25q128, expected s25fl064k
[    0.410000] m25p80 spi32766.0: w25q128 (16384 Kbytes)
[    0.420000] 4 ofpart partitions found on MTD device spi32766.0
[    0.440000] Creating 4 MTD partitions on "spi32766.0":
[    0.450000] 0x000000000000-0x000000030000 : "u-boot"
[    0.460000] 0x000000030000-0x000000040000 : "u-boot-env"
[    0.470000] 0x000000040000-0x000000050000 : "factory"
[    0.480000] 0x000000050000-0x000000fd0000 : "firmware"
[    0.640000] 2 uimage-fw partitions found on MTD device firmware
[    0.660000] 0x000000050000-0x0000001599cd : "kernel"
[    0.670000] 0x0000001599cd-0x000000fd0000 : "rootfs"
[    0.680000] mtd: device 5 (rootfs) set to be root filesystem
[    0.690000] 1 squashfs-split partitions found on MTD device rootfs
[    0.700000] 0x000000350000-0x000000fd0000 : "rootfs_data"
[    0.730000] ralink_soc_eth 10100000.ethernet eth0: ralink at 0xb0100000, irq 5
[    0.740000] rt2880_wdt 10000120.watchdog: Initialized
[    0.760000] TCP: cubic registered
[    0.760000] NET: Registered protocol family 17
[    0.770000] bridge: automatic filtering via arp/ip/ip6tables has been deprecated. Update your scripts to load br_netfilter if you need this.
[    0.800000] 8021q: 802.1Q VLAN Support v1.8
[    0.840000] VFS: Mounted root (squashfs filesystem) readonly on device 31:5.
[    0.850000] Freeing unused kernel memory: 180K (802f3000 - 80320000)
[    3.970000] init: Console is alive
[    3.980000] init: - watchdog -
[    7.000000] usbcore: registered new interface driver usbfs
[    7.010000] usbcore: registered new interface driver hub
[    7.020000] usbcore: registered new device driver usb
[    7.040000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[    7.050000] ehci-platform: EHCI generic platform driver
[    7.260000] phy phy-usbphy.0: remote usb device wakeup disabled
[    7.280000] phy phy-usbphy.0: UTMI 16bit 30MHz
[    7.290000] ehci-platform 101c0000.ehci: EHCI Host Controller
[    7.300000] ehci-platform 101c0000.ehci: new USB bus registered, assigned bus number 1
[    7.310000] ehci-platform 101c0000.ehci: irq 26, io mem 0x101c0000
[    7.350000] ehci-platform 101c0000.ehci: USB 2.0 started, EHCI 1.00
[    7.360000] hub 1-0:1.0: USB hub found
[    7.370000] hub 1-0:1.0: 1 port detected
[    7.380000] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[    7.400000] ohci-platform: OHCI generic platform driver
[    7.410000] ohci-platform 101c1000.ohci: Generic Platform OHCI controller
[    7.420000] ohci-platform 101c1000.ohci: new USB bus registered, assigned bus number 2
[    7.440000] ohci-platform 101c1000.ohci: irq 26, io mem 0x101c1000
[    7.510000] hub 2-0:1.0: USB hub found
[    7.520000] hub 2-0:1.0: 1 port detected
[    8.030000] init: - preinit -
[    9.340000] rt305x-esw 10110000.esw: link changed 0x00
[    9.670000] random: procd urandom read with 15 bits of entropy available
Press the [f] key and hit [enter] to enter failsafe mode
Press the [1], [2], [3] or [4] key and hit [enter] to select the debug level
[   13.060000] mount_root: jffs2 not ready yet, using temporary tmpfs overlay
[   13.120000] procd: - early -
[   13.130000] procd: - watchdog -
[   14.280000] procd: - ubus -
[   15.290000] procd: - init -
Please press Enter to activate this console.
[   16.590000] NET: Registered protocol family 10
[   16.610000] ip6_tables: (C) 2000-2006 Netfilter Core Team
[   16.650000] i2c /dev entries driver
[   16.670000] Loading modules backported from Linux version master-2015-06-22-0-g4732c92
[   16.690000] Backport generated by backports.git backports-20150626-0-gc1a4168
[   16.710000] ip_tables: (C) 2000-2006 Netfilter Core Team
[   16.740000] nf_conntrack version 0.5.0 (456 buckets, 1824 max)
[   16.820000] xt_time: kernel timezone is -0000
[   16.890000] cfg80211: Calling CRDA to update world regulatory domain
[   16.950000] cfg80211: World regulatory domain updated:
[   16.960000] cfg80211:  DFS Master region: unset
[   16.960000] cfg80211:   (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp), (dfs_cac_time)
[   16.980000] cfg80211:   (2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A)
[   17.000000] cfg80211:   (2457000 KHz - 2482000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A)
[   17.020000] cfg80211:   (2474000 KHz - 2494000 KHz @ 20000 KHz), (N/A, 2000 mBm), (N/A)
[   17.030000] cfg80211:   (5170000 KHz - 5250000 KHz @ 80000 KHz, 160000 KHz AUTO), (N/A, 2000 mBm), (N/A)
[   17.050000] cfg80211:   (5250000 KHz - 5330000 KHz @ 80000 KHz, 160000 KHz AUTO), (N/A, 2000 mBm), (0 s)
[   17.070000] cfg80211:   (5490000 KHz - 5730000 KHz @ 160000 KHz), (N/A, 2000 mBm), (0 s)
[   17.090000] cfg80211:   (5735000 KHz - 5835000 KHz @ 80000 KHz), (N/A, 2000 mBm), (N/A)
[   17.100000] cfg80211:   (57240000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 0 mBm), (N/A)
[   17.200000] PPP generic driver version 2.4.2
[   17.220000] NET: Registered protocol family 24
[   17.280000] ieee80211 phy0: rt2x00_set_rt: Info - RT chipset 5350, rev 0500 detected
[   17.300000] ieee80211 phy0: rt2x00_set_rf: Info - RF chipset 5350 detected
[   25.940000] jffs2_scan_eraseblock(): End of filesystem marker found at 0x0
[   26.000000] jffs2_build_filesystem(): unlocking the mtd device... done.
[   26.010000] jffs2_build_filesystem(): erasing all blocks after the end marker...
[   32.060000] device eth0.1 entered promiscuous mode
[   32.070000] device eth0 entered promiscuous mode
[   32.150000] br-lan: port 1(eth0.1) entered forwarding state
[   32.160000] br-lan: port 1(eth0.1) entered forwarding state
[   34.160000] br-lan: port 1(eth0.1) entered forwarding state

正常的启动信息,安装LUCI就挂了
root@OpenWrt:/# df
Filesystem           1K-blocks      Used Available Use% Mounted on
rootfs                   12800     10772      2028  84% /
/dev/root                 2048      2048         0 100% /rom
tmpfs                    14596        64     14532   0% /tmp
/dev/mtdblock6           12800     10772      2028  84% /overlay
overlayfs:/overlay       12800     10772      2028  84% /
tmpfs                      512         0       512   0% /dev


用SCP把overlay 几乎填满了  也没什么问题
我的恩山、我的无线 The best wifi forum is right here.
发表于 2016-10-15 20:43 | 显示全部楼层
非得搞得犯规得分

点评

?? 什么意思?  详情 回复 发表于 2016-10-15 23:18
我的恩山、我的无线 The best wifi forum is right here.
 楼主| 发表于 2016-10-15 23:18 | 显示全部楼层

??
什么意思?
我的恩山、我的无线 The best wifi forum is right here.
 楼主| 发表于 2016-10-16 15:59 | 显示全部楼层
有没有在3053F上开启LUCI的?
我的恩山、我的无线 The best wifi forum is right here.
您需要登录后才可以回帖 登录 | 立即注册

本版积分规则

QQ|手机版|小黑屋|Archiver|恩山无线论坛(常州市恩山计算机开发有限公司版权所有) ( 苏ICP备05084872号 )

GMT+8, 2019-12-16 03:34

Powered by Discuz! X3.4

© 2001-2017 Comsenz Inc.

快速回复 返回顶部 返回列表