|
楼主 |
发表于 2020-1-11 15:27
|
显示全部楼层
原机固件启动过程:
*********************************************
* U-Boot 1.1.4 (Jun 19 2014) *
*********************************************
AP121 (AR9331) U-Boot
DRAM: 64 MB DDR2 16-bit
FLASH: Winbond W25Q128 (16 MB)
CLOCKS: 400/400/200/25 MHz (CPU/RAM/AHB/SPI)
LED on during eth initialization...
Hit any key to stop autobooting: 0
Booting image at: 0x9F020000
Image name: OpenWrt r41503
Image type: MIPS Linux Kernel Image (lzma compressed)
Data size: 929120 Bytes = 907.3 kB
Load address: 0x80060000
Entry point: 0x80060000
Uncompressing kernel image... OK!
Starting kernel...
[ 0.000000] Linux version 3.3.8 (sichaoy@sichao-linux) (gcc version 4.6.3 20120201 (prerelease) (Linaro GCC 4.6-2012.02) ) #34 Tue Nov 3 22:21:32 EST 2015
[ 0.000000] bootconsole [early0] enabled
[ 0.000000] CPU revision is: 00019374 (MIPS 24Kc)
[ 0.000000] SoC: Atheros AR9330 rev 1
[ 0.000000] Clocks: CPU:400.000MHz, DDR:400.000MHz, AHB:200.000MHz, Ref:25.000MHz
[ 0.000000] Determined physical RAM map:
[ 0.000000] memory: 04000000 @ 00000000 (usable)
[ 0.000000] Initrd not found or empty - disabling initrd
[ 0.000000] Zone PFN ranges:
[ 0.000000] Normal 0x00000000 -> 0x00004000
[ 0.000000] Movable zone start PFN for each node
[ 0.000000] Early memory PFN ranges
[ 0.000000] 0: 0x00000000 -> 0x00004000
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 16256
[ 0.000000] Kernel command line: board=TL-WR741ND-v4 console=ttyATH0,115200 rootfstype=squashfs,jffs2 noinitrd
[ 0.000000] PID hash table entries: 256 (order: -2, 1024 bytes)
[ 0.000000] Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
[ 0.000000] Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
[ 0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
[ 0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes
[ 0.000000] Writing ErrCtl register=00000000
[ 0.000000] Readback ErrCtl register=00000000
[ 0.000000] Memory: 61588k/65536k available (2129k kernel code, 3948k reserved, 408k data, 208k init, 0k highmem)
[ 0.000000] SLUB: Genslabs=9, HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[ 0.000000] NR_IRQS:51
[ 0.000000] Calibrating delay loop... 265.42 BogoMIPS (lpj=1327104)
[ 0.080000] pid_max: default: 32768 minimum: 301
[ 0.080000] Mount-cache hash table entries: 512
[ 0.090000] NET: Registered protocol family 16
[ 0.090000] gpiochip_add: registered GPIOs 0 to 29 on device: ath79
[ 0.100000] MIPS: machine is TP-LINK TL-WR741ND v4
[ 0.520000] bio: create slab <bio-0> at 0
[ 0.530000] Switching to clocksource MIPS
[ 0.530000] NET: Registered protocol family 2
[ 0.540000] IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.540000] TCP established hash table entries: 2048 (order: 2, 16384 bytes)
[ 0.550000] TCP bind hash table entries: 2048 (order: 1, 8192 bytes)
[ 0.550000] TCP: Hash tables configured (established 2048 bind 2048)
[ 0.560000] TCP reno registered
[ 0.560000] UDP hash table entries: 256 (order: 0, 4096 bytes)
[ 0.570000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[ 0.570000] NET: Registered protocol family 1
[ 0.600000] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 0.600000] JFFS2 version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[ 0.610000] msgmni has been set to 120
[ 0.610000] io scheduler noop registered
[ 0.620000] io scheduler deadline registered (default)
[ 0.620000] Serial: 8250/16550 driver, 1 ports, IRQ sharing disabled
[ 0.630000] ar933x-uart: ttyATH0 at MMIO 0x18020000 (irq = 11) is a AR933X UART
[ 0.640000] console [ttyATH0] enabled, bootconsole disabled
[ 0.640000] console [ttyATH0] enabled, bootconsole disabled
[ 0.650000] m25p80 spi0.0: found w25q128, expected m25p80
[ 0.650000] m25p80 spi0.0: w25q128 (16384 Kbytes)
[ 0.660000] 5 tp-link partitions found on MTD device spi0.0
[ 0.670000] Creating 5 MTD partitions on "spi0.0":
[ 0.670000] 0x000000000000-0x000000020000 : "u-boot"
[ 0.680000] 0x000000020000-0x000000102f60 : "kernel"
[ 0.680000] mtd: partition "kernel" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only
[ 0.690000] 0x000000102f60-0x000000ff0000 : "rootfs"
[ 0.700000] mtd: partition "rootfs" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only
[ 0.710000] mtd: partition "rootfs" set to be root filesystem
[ 0.720000] mtd: partition "rootfs_data" created automatically, ofs=620000, len=9D0000
[ 0.730000] 0x000000620000-0x000000ff0000 : "rootfs_data"
[ 0.730000] 0x000000ff0000-0x000001000000 : "art"
[ 0.740000] 0x000000020000-0x000000ff0000 : "firmware"
[ 0.760000] ag71xx_mdio: probed
[ 0.770000] eth0: Atheros AG71xx at 0xba000000, irq 5
[ 1.320000] eth0: Found an AR7240/AR9330 built-in switch
[ 2.350000] eth1: Atheros AG71xx at 0xb9000000, irq 4
[ 2.900000] ag71xx ag71xx.0: eth1: connected to PHY at ag71xx-mdio.1:04 [uid=004dd041, driver=Generic PHY]
[ 2.910000] TCP cubic registered
[ 2.910000] NET: Registered protocol family 17
[ 2.920000] 8021q: 802.1Q VLAN Support v1.8
[ 2.920000] VFS: Mounted root (squashfs filesystem) readonly on device 31:2.
[ 2.930000] Freeing unused kernel memory: 208k freed
mn- preinit -
Press the [f] key and hit [enter] to enter failsafe mode
[ 6.870000] eth0: link up (1000Mbps/Full duplex)
- regular preinit -
[ 9.630000] JFFS2 notice: (415) jffs2_build_xattr_subsystem: complete building xattr subsystem, 1 of xdatum (0 unchecked, 0 orphan) and 12 of xref (0 dead, 0 orphan) found.
switching to jffs2
- init -
[ 9.850000] eth0: link down
Please press Enter to activate this console. [ 12.030000] Loading modules backported from Linux version master-2014-05-22-0-gf2032ea
[ 12.040000] Backport generated by backports.git backports-20140320-37-g5c33da0
[ 12.220000] cfg80211: Calling CRDA to update world regulatory domain
[ 12.220000] cfg80211: World regulatory domain updated:
[ 12.230000] cfg80211: DFS Master region: unset
[ 12.230000] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp), (dfs_cac_time)
[ 12.240000] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A)
[ 12.250000] cfg80211: (2457000 KHz - 2482000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A)
[ 12.260000] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (N/A, 2000 mBm), (N/A)
[ 12.260000] cfg80211: (5170000 KHz - 5250000 KHz @ 80000 KHz), (N/A, 2000 mBm), (N/A)
[ 12.270000] cfg80211: (5735000 KHz - 5835000 KHz @ 80000 KHz), (N/A, 2000 mBm), (N/A)
[ 12.280000] cfg80211: (57240000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 0 mBm), (N/A)
[ 12.710000] usbcore: registered new interface driver usbfs
[ 12.720000] usbcore: registered new interface driver hub
[ 12.720000] usbcore: registered new device driver usb
[ 13.410000] ieee80211 phy0: Atheros AR9330 Rev:1 mem=0xb8100000, irq=2
[ 13.410000] cfg80211: Calling CRDA for country: US
[ 13.420000] cfg80211: Regulatory domain changed to country: US
[ 13.420000] cfg80211: DFS Master region: FCC
[ 13.430000] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp), (dfs_cac_time)
[ 13.440000] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A, 3000 mBm), (N/A)
[ 13.450000] cfg80211: (5170000 KHz - 5250000 KHz @ 80000 KHz), (N/A, 1700 mBm), (N/A)
[ 13.450000] cfg80211: (5250000 KHz - 5330000 KHz @ 80000 KHz), (N/A, 2300 mBm), (0 s)
[ 13.460000] cfg80211: (5735000 KHz - 5835000 KHz @ 80000 KHz), (N/A, 3000 mBm), (N/A)
[ 13.470000] cfg80211: (57240000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 4000 mBm), (N/A)
[ 13.550000] PPP generic driver version 2.4.2
[ 13.580000] tun: Universal TUN/TAP device driver, 1.6
[ 13.590000] tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
[ 13.800000] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 14.050000] NET: Registered protocol family 24
[ 14.070000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 14.100000] nf_conntrack version 0.5.0 (965 buckets, 3860 max)
[ 14.520000] xt_time: kernel timezone is -0000
[ 14.750000] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[ 20.860000] device eth0.1 entered promiscuous mode
[ 20.860000] device eth0 entered promiscuous mode
[ 20.880000] device eth0.2 entered promiscuous mode
[ 21.460000] eth0: link up (1000Mbps/Full duplex)
[ 21.460000] br-lan: port 1(eth0.1) entered forwarding state
[ 21.470000] br-lan: port 1(eth0.1) entered forwarding state
[ 21.480000] br-wifi: port 1(eth0.2) entered forwarding state
[ 21.480000] br-wifi: port 1(eth0.2) entered forwarding state
[ 23.470000] br-lan: port 1(eth0.1) entered forwarding state
[ 23.480000] br-wifi: port 1(eth0.2) entered forwarding state
[ 29.750000] device wlan0 entered promiscuous mode
[ 29.770000] br-wifi: port 2(wlan0) entered forwarding state
[ 29.770000] br-wifi: port 2(wlan0) entered forwarding state
[ 29.790000] device wlan0-1 entered promiscuous mode
[ 30.180000] br-lan: port 2(wlan0-1) entered forwarding state
[ 30.180000] br-lan: port 2(wlan0-1) entered forwarding state
[ 30.210000] device wlan0-2 entered promiscuous mode
[ 30.230000] br-wifi: port 3(wlan0-2) entered forwarding state
[ 30.230000] br-wifi: port 3(wlan0-2) entered forwarding state
[ 31.770000] br-wifi: port 2(wlan0) entered forwarding state
[ 32.180000] br-lan: port 2(wlan0-1) entered forwarding state
[ 32.230000] br-wifi: port 3(wlan0-2) entered forwarding state
BusyBox v1.19.4 (2014-10-17 23:46:30 EDT) built-in shell (ash)
Enter 'help' for a list of built-in commands.
_______ ________ __
| |.-----.-----.-----.| | | |.----.| |_
| - || _ | -__| || | | || _|| _|
|_______|| __|_____|__|__||________||__| |____|
|__| W I R E L E S S F R E E D O M
-----------------------------------------------------
ATTITUDE ADJUSTMENT (Attitude Adjustment, r41503)
-----------------------------------------------------
* 1/4 oz Vodka Pour all ingredients into mixing
* 1/4 oz Gin tin with ice, strain into glass.
* 1/4 oz Amaretto
* 1/4 oz Triple sec
* 1/4 oz Peach schnapps
* 1/4 oz Sour mix
* 1 splash Cranberry juice
-----------------------------------------------------
wifisongadmin@ws151:/#
wifisongadmin@ws151:/# |
|