|
|
请问大家，opboot-p2w-r619ac-nor-v1.1.2-3d5736d.img 是否可以用编程器直接刷入？
我是竞斗云2.0版，升级潘多拉变砖了，但uboot敲键盘停不下来，请问有什么办法能修复？
U-Boot 2012.07 [Chaos Calmer 15.05.1,unknown] (Dec 27 2017 - 12:06:09)
smem ram ptable found: ver: 1 len: 3
DRAM: 512 MiB
machid : 0x8010006
NAND: ID = 1d00f101
Vendor = 1
Device = f1
ONFI device found
Is a spansion device needing reset logic
SF: Detected W25Q128 with page size 64 KiB, total 16 MiB
ipq_spi: page_size: 0x100, sector_size: 0x10000, size: 0x1000000
144 MiB
MMC: qca_mmc: 0
In: serial
Out: serial
Err: serial
machid: 8010006
flash_type: 0
Hit any key to stop autoboot: 0
Creating 1 MTD partitions on "nand0":
0x000000000000-0x000004000000 : "mtd=0"
UBI: attaching mtd2 to ubi0
UBI: physical eraseblock size: 131072 bytes (128 KiB)
UBI: logical eraseblock size: 126976 bytes
UBI: smallest flash I/O unit: 2048
UBI: VID header offset: 2048 (aligned 2048)
UBI: data offset: 4096
UBI: attached mtd2 to ubi0
UBI: MTD device name: "mtd=0"
UBI: MTD device size: 64 MiB
UBI: number of good PEBs: 512
UBI: number of bad PEBs: 0
UBI: max. allowed volumes: 128
UBI: wear-leveling threshold: 4096
UBI: number of internal volumes: 1
UBI: number of user volumes: 3
UBI: available PEBs: 15
UBI: total number of reserved PEBs: 497
UBI: number of PEBs reserved for bad PEB handling: 5
UBI: max/mean erase counter: 7/3
Read 0 bytes from volume kernel to 84000000
No size specified -> Using max size (2666496)
## Booting kernel from FIT Image at 84000000 ...
Using 'config@10' configuration
Trying 'kernel@1' kernel subimage
Description: ARM PandoraBox Linux-3.14.79
Type: Kernel Image
Compression: gzip compressed
Data Start: 0x840000ec
Data Size: 2560294 Bytes = 2.4 MiB
Architecture: ARM
OS: Linux
Load Address: 0x80208000
Entry Point: 0x80208000
Hash algo: crc32
Hash value: 6b656995
Hash algo: sha1
Hash value: d6dbb33109442c638d6a6cde1aadc0a8a9f6389e
Verifying Hash Integrity ... crc32+ sha1+ OK
## Flattened Device Tree from FIT Image at 84000000
Using 'config@10' configuration
Trying 'fdt@1' FDT blob subimage
Description: ARM PandoraBox p2w_r619ac device tree blob
Type: Flat Device Tree
Compression: uncompressed
Data Start: 0x8427134c
Data Size: 39748 Bytes = 38.8 KiB
Architecture: ARM
Hash algo: crc32
Hash value: fe038ffe
Hash algo: sha1
Hash value: 9192eb947b9f119b7d1f87c4df63d8457e6ef6e0
Verifying Hash Integrity ... crc32+ sha1+ OK
Booting using the fdt blob at 0x8427134c
Uncompressing Kernel Image ... OK
Loading Device Tree to 86ff3000, end 86fffb43 ... OK
ipq: fdt fixup unable to find compatible node
Using machid 0x8010006 from environment
Starting kernel ...
[ 0.000000] Booting Linux on physical CPU 0x0
[ 0.000000] Initializing cgroup subsys cpuset
[ 0.000000] Initializing cgroup subsys cpu
[ 0.000000] Initializing cgroup subsys cpuacct
[ 0.000000] Linux version 3.14.79 (lintel@lintel-dev-vm) (gcc version 5.5.0 (PandoraBox GCC 5.5.0 2020-03-06-git-e4fb2dd33) ) #0 SMP Fri Mar 6 22:02:15 2020
[ 0.000000] CPU: ARMv7 Processor [410fc075] revision 5 (ARMv7), cr=10c5387d
[ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
[ 0.000000] Machine model: P&W R619AC
[ 0.000000] Memory policy: Data cache writealloc
[ 0.000000] PERCPU: Embedded 7 pages/cpu @dfbc7000 s7744 r8192 d12736 u32768
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 129536
[ 0.000000] Kernel command line: ubi.mtd=rootfs root=mtd:ubi_rootfs rootfstype=squashfs rootwait clk_ignore_unused
[ 0.000000] Skip rootfs setup.
[ 0.000000] Skip rootfs type setup.
[ 0.000000] PID hash table entries: 2048 (order: 1, 8192 bytes)
[ 0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
[ 0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
[ 0.000000] allocated 1048576 bytes of page_cgroup
[ 0.000000] please try 'cgroup_disable=memory' option if you don't want memory cgroups
[ 0.000000] Memory: 510444K/522240K available (3644K kernel code, 191K rwdata, 1404K rodata, 175K init, 584K bss, 11796K reserved)
[ 0.000000] Virtual kernel memory layout:
[ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB)
[ 0.000000] fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB)
[ 0.000000] vmalloc : 0xe0800000 - 0xff000000 ( 488 MB)
[ 0.000000] lowmem : 0xc0000000 - 0xe0000000 ( 512 MB)
[ 0.000000] modules : 0xbe000000 - 0xc0000000 ( 32 MB)
[ 0.000000] .text : 0xc0208000 - 0xc06f6224 (5049 kB)
[ 0.000000] .init : 0xc06f7000 - 0xc0722e40 ( 176 kB)
[ 0.000000] .data : 0xc0724000 - 0xc0753f60 ( 192 kB)
[ 0.000000] .bss : 0xc0753f60 - 0xc07e622c ( 585 kB)
[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1
[ 0.000000] Hierarchical RCU implementation.
[ 0.000000] NR_IRQS:16 nr_irqs:16 16
[ 0.000000] Architected cp15 timer(s) running at 48.00MHz (virt).
[ 0.000008] sched_clock: 56 bits at 48MHz, resolution 20ns, wraps every 2863311552512ns
[ 0.000016] Switching to timer-based delay loop
[ 0.000271] Calibrating delay loop (skipped), value calculated using timer frequency.. 96.00 BogoMIPS (lpj=192000)
[ 0.000287] pid_max: default: 32768 minimum: 301
[ 0.000551] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.000565] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.011913] Initializing cgroup subsys memory
[ 0.011956] Initializing cgroup subsys devices
[ 0.011969] Initializing cgroup subsys freezer
[ 0.011980] Initializing cgroup subsys net_cls
[ 0.011989] Initializing cgroup subsys blkio
[ 0.011998] Initializing cgroup subsys perf_event
[ 0.012021] Initializing cgroup subsys net_prio
[ 0.012069] CPU: Testing write buffer coherency: ok
[ 0.012424] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000
[ 0.012494] Setting up static identity map for 0x80212450 - 0x80212484
[ 0.014400] CPU1: Booted secondary processor
[ 0.014445] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001
[ 0.015230] CPU2: Booted secondary processor
[ 0.015268] CPU2: thread -1, cpu 2, socket 0, mpidr 80000002
[ 0.016022] CPU3: Booted secondary processor
[ 0.016058] CPU3: thread -1, cpu 3, socket 0, mpidr 80000003
[ 0.016178] Brought up 4 CPUs
[ 0.016216] SMP: Total of 4 processors activated (384.00 BogoMIPS).
[ 0.016224] CPU: All CPU(s) started in SVC mode.
[ 0.026195] VFP support v0.3: implementor 41 architecture 2 part 30 variant 7 rev 5
[ 0.027345] pinctrl core: initialized pinctrl subsystem
[ 0.028134] regulator-dummy: no parameters
[ 0.029024] NET: Registered protocol family 16
[ 0.029302] DMA: preallocated 256 KiB pool for atomic coherent allocations
[ 0.030471] cpuidle: using governor ladder
[ 0.030485] cpuidle: using governor menu
[ 0.044832] hw-breakpoint: Debug register access (0xee003e17) caused undefined instruction on CPU 1
[ 0.044840] hw-breakpoint: Debug register access (0xee003e17) caused undefined instruction on CPU 2
[ 0.044849] hw-breakpoint: Debug register access (0xee003e17) caused undefined instruction on CPU 3
[ 0.044853] hw-breakpoint: CPU 2 failed to disable vector catch
[ 0.044885] hw-breakpoint: Debug register access (0xee003e17) caused undefined instruction on CPU 0
[ 0.044968]
[ 0.044968] Version Rollback Feature Disabled
[ 0.049057] sps:sps is ready.
[ 0.057124] bio: create slab <bio-0> at 0
[ 0.058764] SD0 VccQ: 1800 <--> 3000 mV
[ 0.060389] msm_bus_fabric_init_driver
[ 0.060557] msm_bus_device 580000.ad-hoc-bus: Util-fact is missing, default to 100
[ 0.060573] msm_bus_device 580000.ad-hoc-bus: Vrail-comp is missing, default to 100
[ 0.060593] msm_bus_device 580000.ad-hoc-bus: Failed to get bus clk for bus4096 ctx1
[ 0.060640] msm_bus_device 580000.ad-hoc-bus: Util-fact is missing, default to 100
[ 0.060656] msm_bus_device 580000.ad-hoc-bus: Vrail-comp is missing, default to 100
[ 0.060672] msm_bus_device 580000.ad-hoc-bus: Failed to get bus clk for bus1024 ctx1
[ 0.095073] 80000.qcom,pcie supply vreg-3.3 not found, using dummy regulator
[ 0.095179] 80000.qcom,pcie supply vreg-1.8 not found, using dummy regulator
[ 0.095235] 80000.qcom,pcie supply vreg-0.9 not found, using dummy regulator
[ 0.095303] 80000.qcom,pcie supply gdsc-vdd not found, using dummy regulator
[ 0.172591] msm_pcie_enable: msm_pcie_enable: PCIe: trigger the reset of endpoint of RC0.
[ 0.176577] msm_pcie_enable: msm_pcie_enable: PCIe RC0 PHY is ready!
[ 0.192596] msm_pcie_enable: msm_pcie_enable: PCIe: Release the reset of endpoint of RC0.
[ 0.324909] msm_pcie_enable: msm_pcie_enable: RC0:No. 1 TSSM_STATE:0x0
[ 0.356995] msm_pcie_enable: msm_pcie_enable: RC0:No. 2TSSM_STATE:0x0
[ 0.389082] msm_pcie_enable: msm_pcie_enable: RC0:No. 3TSSM_STATE:0x0
[ 0.421170] msm_pcie_enable: msm_pcie_enable: RC0:No. 4TSSM_STATE:0x0
[ 0.453257] msm_pcie_enable: msm_pcie_enable: RC0:No. 5TSSM_STATE:0x0
[ 0.485342] msm_pcie_enable: msm_pcie_enable: PCIe: trigger the reset of endpoint of RC0.
[ 0.485357] msm_pcie_enable: msm_pcie_enable: PCIe RC0 link initialization failed
[ 0.485386] msm_pcie_enumerate: msm_pcie_enumerate: PCIe: failed to enable RC0.
[ 0.485397] msm_pcie_probe: msm_pcie_probe: PCIe: RC0 is not enabled during bootup; it will be enumerated upon WAKE signal.
[ 0.485408] msm_pcie_probe: msm_pcie_probe: PCIe: Driver probe failed for RC0:-1
[ 0.485816] msm_pcie: probe of 80000.qcom,pcie failed with error -1
[ 0.486186] Switched to clocksource arch_sys_counter
[ 0.486383] PandoraBox SPLICE initialized. rcv df7a8000 (sz:768) kvec df570000 (sz:256) per 4 core
[ 0.489320] NET: Registered protocol family 2
[ 0.490458] TCP established hash table entries: 4096 (order: 2, 16384 bytes)
[ 0.490535] TCP bind hash table entries: 4096 (order: 3, 32768 bytes)
[ 0.490623] TCP: Hash tables configured (established 4096 bind 4096)
[ 0.490680] TCP: reno registered
[ 0.490696] UDP hash table entries: 256 (order: 1, 8192 bytes)
[ 0.490728] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes)
[ 0.491061] NET: Registered protocol family 1
[ 0.491716] hw perfevents: enabled with ARMv7 Cortex-A7 PMU driver, 5 counters available
[ 0.492054] Qualcomm IPQ40xx/IPQ806x GPIO Resource maped.
[ 0.494646] futex hash table entries: 1024 (order: 4, 65536 bytes)
[ 0.507978] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 0.507994] jffs2: version 2.2 (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[ 0.509096] msgmni has been set to 996
[ 0.510048] io scheduler noop registered (default)
[ 0.510062] io scheduler deadline registered
[ 0.510104] io scheduler cfq registered
[ 0.510503] io scheduler bfq registered
[ 0.510514] BFQ I/O-scheduler: v7r8
[ 0.511106] gpio-export gpio_export.7: 1 gpio(s) exported
[ 0.511915] tcsr 194b000.tcsr: setting usb hs phy mode select = e700e7
[ 0.511993] tcsr 1953000.ess_tcsr: setting ess interface select = 0
[ 0.512060] tcsr 1949000.tcsr: setting wifi_glb_cfg = 41000000
[ 0.512113] tcsr 1957000.tcsr: setting wifi_noc_memtype_m0_m2 = 2222222
[ 0.512863] Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled
[ 0.514167] msm_serial_hsl_probe: detected port #0 (ttyMSM0)
[ 0.514242] msm_serial_hsl_probe: Bus scaling is disabled
[ 0.514341] 78af000.serial: ttyMSM0 at MMIO 0x78af000 (irq = 139, base_baud = 115200) is a MSM
[ 0.514410] msm_hsl_console_setup: console setup on port #0
[ 1.306034] console [ttyMSM0] enabled
[ 1.310207] msm_serial_hsl_probe: detected port #1 (ttyMSM1)
[ 1.315346] msm_serial_hsl_probe: Bus scaling is disabled
[ 1.320775] 78b0000.serial: ttyMSM1 at MMIO 0x78b0000 (irq = 140, base_baud = 115200) is a MSM
[ 1.330053] msm_serial_hsl_init: driver initialized
[ 1.334753] msm_serial_hs module loaded
[ 1.338504] qca_serial_hs module loaded
[ 1.343864] mtdoops: mtd device (mtddev=name/number) must be supplied
[ 1.349490] sps: BAM device 0x07984000 is not registered yet.
[ 1.355046] sps:BAM 0x07984000 is registered.
[ 1.359184] msm_nand_bam_init: msm_nand_bam_init: BAM device registered: bam_handle 0xdec00000
[ 1.368107] sps:BAM 0x07984000 (va:0xe0960000) enabled: ver:0x19, number of pipes:7
[ 1.375823] msm_nand_version_check: nand_major:1, nand_minor:4, qpic_major:1, qpic_minor:4
[ 1.384193] msm_nand_flash_onfi_probe: Found an ONFI compliant device S34ML01G1
[ 1.392177] msm_nand_scan: NAND Id: 0x1d00f101 Buswidth: 8Bits Density: 128 MByte
[ 1.399638] msm_nand_scan: pagesize: 2048 Erasesize: 131072 oobsize: 64 (in Bytes)
[ 1.407186] msm_nand_scan: BCH ECC: 4 Bit
[ 1.411185] msm_nand_scan: CFG0: 0x2a0408c0, CFG1: 0x0804745c
[ 1.411185] RAWCFG0: 0x280420c0, RAWCFG1: 0x0005045d
[ 1.411185] ECCBUFCFG: 0x00000203, ECCBCHCFG: 0x42040700
[ 1.411185] BAD BLOCK BYTE: 0x000001d1
[ 1.434126] 1 ofpart partitions found on MTD device 7980000.qcom,nand
[ 1.440269] Creating 1 MTD partitions on "7980000.qcom,nand":
[ 1.445993] 0x000000000000-0x000008000000 : "ubi"
[ 1.617987] msm_nand_probe: NANDc phys addr 0x7980000, BAM phys addr 0x7984000, BAM IRQ 133
[ 1.625342] msm_nand_probe: Allocated DMA buffer at virt_addr 0xe08e1000, phys_addr 0x9f6ce000
[ 1.634725] sps: BAM device 0x07884000 is not registered yet.
[ 1.639664] sps:BAM 0x07884000 is registered.
[ 1.645026] m25p80 spi0.0: w25q128 (16384 Kbytes)
[ 1.648894] m25p80 spi0.0: SPI max clock set to 24MHz
[ 1.654211] 9 ofpart partitions found on MTD device spi0.0
[ 1.659377] Creating 9 MTD partitions on "spi0.0":
[ 1.664163] 0x000000000000-0x000000040000 : "SBL1"
[ 1.670680] 0x000000040000-0x000000060000 : "MIBIB"
[ 1.676028] 0x000000060000-0x0000000c0000 : "QSEE"
[ 1.681138] 0x0000000c0000-0x0000000d0000 : "CDT"
[ 1.686168] 0x0000000d0000-0x0000000e0000 : "DDRPARAMS"
[ 1.691765] 0x0000000e0000-0x0000000f0000 : "APPSBLENV"
[ 1.697335] 0x0000000f0000-0x000000170000 : "APPSBL"
[ 1.702730] 0x000000170000-0x000000180000 : "ART"
[ 1.707816] 0x000000000000-0x000000170000 : "Bootloader"
[ 1.730510] libphy: ipq40xx_mdio: probed
[ 1.737469] ipq40xx-mdio 90000.mdio: ipq40xx-mdio driver was registered
[ 1.744298] requesting memory region failed
[ 1.761814] TCP: cubic registered
[ 1.779494] NET: Registered protocol family 10
[ 1.795412] NET: Registered protocol family 17
[ 1.800561] Bridge firewalling registered
[ 1.803953] 8021q: 802.1Q VLAN Support v1.8
[ 1.808407] PandoraBox Mass Storage accelerater v1.2
[ 1.813543] ThumbEE CPU extension supported.
[ 1.817364] Registering SWP/SWPB emulation handler
[ 1.823922] SD0 VccQ: disabling
[ 1.826041] regulator-dummy: disabling
[ 1.830685] UBI error: ubi_init: cannot open mtd rootfs, error -2
[ 1.836417] UBI: auto-attach mtd0
[ 1.839171] UBI: attaching mtd0 to ubi0
[ 2.320398] UBI: EOF marker found, PEBs from 409 will be erased
[ 2.424913] UBI: scanning is finished
[ 2.427602] UBI error: ubi_read_volume_table: the layout volume was not found
[ 2.435256] UBI error: ubi_attach_mtd_dev: failed to attach mtd0, error -22
[ 2.441640] UBI error: ubi_auto_attach: cannot attach mtd0
[ 2.450556] clk: Not disabling unused clocks
[ 2.454106] 6Waiting for root device ...
|
|
简体中文
繁體中文
English
日本語
Deutsch
한국 사람
بالعربية
TÜRKÇE
português
คนไทย
IP卡
狗仔卡
发表于 2020-3-27 18:39
显身卡