刷自己编译的固件无法启动，大家给看看

wlgui007

第一次编译固件，没想到这么不顺利
路由器： OYE-0001 哦耶

什么都没选，只选了LUCI

TTL信息如下：


U-Boot 1.1.3 (Jul 19 2014 - 11:00:34)

SoC:MediaTek MT7620
DRAM:  Memory Testing..131072K OK. is 128 MB
relocate_code Pointer at: 87fa8000
enable ephy clock...done. rf reg 29 = 5
SSC disabled.
spi_wait_nsec: 29
spi device id: ef 40 18 0 0 (40180000)
find flash: W25Q128BV
raspi_read: from:30000 len:1000
*** Warning - bad CRC, using default environment

__________________________________________________________________
|    ______        ___    ____   ___  _ _                        |
|   / ___\ \      / / \  |___ \ / _ \/ / |  ___ ___  _ __ ___    |
|  | |  _ \ \ /\ / / _ \   __) | | | | | | / __/ _ \| '_ ` _ \   |
|  | |_| | \ V  V / ___ \ / __/| |_| | | || (_| (_) | | | | | |  |
|   \____|  \_/\_/_/   \_\_____|\___/|_|_(_)___\___/|_| |_| |_|  |
|                                                                |
|                Hangzhou OYE Technology Co. LTD                 |
|                   Global Wireless Alliance                     |
|                       Board: OYE-0001                          |
|                    http://www.oyewifi.com                      |
|                        QQ:800007540                            |
|                     Copyright @2012-2014                       |
|________________________________________________________________|

===============System Info==================
ASIC 7620_MP (Port5<->None)
DRAM component: 1024 Mbits DDR, width 16
DRAM bus: 16 bit
Flash component: SPI Flash
CPU Speed: 580 MHZ
RAM Size:128 Mbytes

Build Date:Jul 19 2014  Time:11:00:34
============================================

GPIO Init:
        UARTF_SHARE_MODE:GPIO
        I2C_GPIO_MODE:GPIO

GPIO_MODE_REG status:0x1a311d
ReadyLED Bit:0x1

Please choose the operation:
   1: Load system code to SDRAM via TFTP.
   2: Load system code then write to Flash via TFTP.
   3: Boot system code via Flash (default).
   4: Entr boot command line interface.
   7: Load Boot Loader code then write to Flash via Serial.
   9: Load Boot Loader code then write to Flash via TFTP.
0
   
3: System Boot system code via Flash.

Press Reset button enter upgrade mode!
## Booting image at bc050000 ...
raspi_read: from:50000 len:40
   Image Name:   MIPS OpenWrt Linux-4.4.7
   Image Type:   MIPS Linux Kernel Image (lzma compressed)
   Data Size:    1278004 Bytes =  1.2 MB
   Load Address: 80000000
   Entry Point:  80000000
raspi_read: from:50040 len:138034
   Verifying Checksum ... OK
   Uncompressing Kernel Image ... OK
No initrd
## Transferring control to Linux (at address 80000000) ...
## Giving linux memsize in MB, 128

Starting kernel ...

[    0.000000] Linux version 4.4.7 (work-wlgui@workwlgui-virtual-machine) (gcc version 5.3.0 (OpenWrt GCC 5.3.0 r49395) ) #2 Tue Sep 19 01:33:28 UTC 2017
[    0.000000] Board has DDR2
[    0.000000] Analog PMU set to hw control
[    0.000000] Digital PMU set to hw control
[    0.000000] SoC Type: MediaTek MT7620A ver:2 eco:6
[    0.000000] bootconsole [early0] enabled
[    0.000000] CPU0 revision is: 00019650 (MIPS 24KEc)
[    0.000000] MIPS: machine is Ralink MT7620a + MT7610e evaluation board
[    0.000000] Determined physical RAM map:
[    0.000000]  memory: 08000000 @ 00000000 (usable)
[    0.000000] Initrd not found or empty - disabling initrd
[    0.000000] Zone ranges:
[    0.000000]   Normal   [mem 0x0000000000000000-0x0000000007ffffff]
[    0.000000] Movable zone start for each node
[    0.000000] Early memory node ranges
[    0.000000]   node   0: [mem 0x0000000000000000-0x0000000007ffffff]
[    0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x0000000007ffffff]
[    0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
[    0.000000] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 32512
[    0.000000] Kernel command line: console=ttyS0,57600 rootfstype=squashfs,jffs2
[    0.000000] PID hash table entries: 512 (order: -1, 2048 bytes)
[    0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
[    0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
[    0.000000] Writing ErrCtl register=00074016
[    0.000000] Readback ErrCtl register=00074016
[    0.000000] Memory: 125748K/131072K available (2879K kernel code, 133K rwdata, 696K rodata, 188K init, 195K bss, 5324K reserved, 0K cma-reserved)
[    0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[    0.000000] NR_IRQS:256
[    0.000000] CPU Clock: 580MHz
[    0.000000] clocksource: systick: mask: 0xffff max_cycles: 0xffff, max_idle_ns: 583261500 ns
[    0.000000] systick: enable autosleep mode
[    0.000000] systick: running - mult: 214748, shift: 32
[    0.000000] clocksource: MIPS: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 6590553264 ns
[    0.000011] sched_clock: 32 bits at 290MHz, resolution 3ns, wraps every 7405115902ns
[    0.007567] Calibrating delay loop... 385.84 BogoMIPS (lpj=1929216)
[    0.070070] pid_max: default: 32768 minimum: 301
[    0.074699] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
[    0.081075] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
[    0.094035] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[    0.103704] pinctrl core: initialized pinctrl subsystem
[    0.109445] NET: Registered protocol family 16
[    0.599520] mt7620-pci 10140000.pcie: PCIE0 no card, disable it(RST&CLK)
[    0.606000] mt7620-pci: probe of 10140000.pcie failed with error -1
[    0.620523] rt2880_gpio 10000600.gpio: registering 24 gpios
[    0.625916] rt2880_gpio 10000600.gpio: registering 24 irq handlers
[    0.633615] clocksource: Switched to clocksource systick
[    0.640214] NET: Registered protocol family 2
[    0.645386] TCP established hash table entries: 1024 (order: 0, 4096 bytes)
[    0.652112] TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
[    0.658328] TCP: Hash tables configured (established 1024 bind 1024)
[    0.664551] UDP hash table entries: 256 (order: 0, 4096 bytes)
[    0.670177] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[    0.676586] NET: Registered protocol family 1
[    0.681306] rt-timer 10000100.timer: maximum frequency is 1220Hz
[    0.688179] futex hash table entries: 256 (order: -1, 3072 bytes)
[    0.712700] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[    0.718383] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[    0.730633] io scheduler noop registered
[    0.734456] io scheduler deadline registered (default)
[    0.739625] ralink-usb-phy usbphy: invalid resource
[    0.745023] Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled
[    0.752412] console [ttyS0] disabled
f`f~fx怘f`f~fx怘`xfx怘`xfx怘~f
后边都是乱码。。。




PING路由器信息：
wlgui@wlgui-Computer:~$ ping 192.168.1.1
PING 192.168.1.1 (192.168.1.1) 56(84) bytes of data.
From 192.168.1.111 icmp_seq=1 Destination Host Unreachable
From 192.168.1.111 icmp_seq=2 Destination Host Unreachable
From 192.168.1.111 icmp_seq=3 Destination Host Unreachable
From 192.168.1.111 icmp_seq=4 Destination Host Unreachable
From 192.168.1.111 icmp_seq=5 Destination Host Unreachable
From 192.168.1.111 icmp_seq=6 Destination Host Unreachable
64 bytes from 192.168.1.1: icmp_seq=7 ttl=64 time=1000 ms
64 bytes from 192.168.1.1: icmp_seq=8 ttl=64 time=0.549 ms
64 bytes from 192.168.1.1: icmp_seq=9 ttl=64 time=0.353 ms
64 bytes from 192.168.1.1: icmp_seq=10 ttl=64 time=0.372 ms
之后就不动了，重启还是只能ping通一会儿

小学生414

配置文件里面有oye的配置。你可以试一下，别先用evb，我这里实测可以。

fghlw

我之前编译也是   只要一选LUCI就挂

wlgui007

王福迎 发表于 2017-9-23 23:00
配置文件里面有oye的配置。你可以试一下，别先用evb，我这里实测可以。

今天刚有时间测试了下,果然是您说的.谢谢