|
|
尝试几次都失败 求助论坛 TTL 启动信息 QQ15220709
U-Boot 1.1.4 (Jan 10 2013 - 11:03:59)
AP100 (ar934x) U-boot
DRAM:
sri
Wasp 1.2
wasp_ddr_initial_config(276): Wasp (16bit) ddr1 init
wasp_ddr_initial_config(426): Wasp ddr init done
Tap value selected = 0x8 [0xaa55aa55 - 0x0]
Setting 0xb8116290 to 0x44882d0f
4 MB
Top of RAM usable for U-Boot at: 80400000
Reserving 230k for U-Boot at: 803c4000
Reserving 192k for malloc() at: 80394000
Reserving 44 Bytes for Board Info at: 80393fd4
Reserving 36 Bytes for Global Data at: 80393fb0
Reserving 128k for boot params() at: 80373fb0
Stack Pointer at: 80373f98
0
Validating MD5Sum of 'vmlinux'... Passed!
Validating MD5Sum of 'rootfs'. 0
ar7240> help
? - alias for 'help'
autoscr - run script from memory
base - print or set address offset
bdinfo - print Board Info structure
boot - boot default, i.e., run 'bootcmd'
bootd - boot default, i.e., run 'bootcmd'
bootelf - Boot from an ELF image in memory
bootm - boot application image from memory
bootp - boot image via network using BootP/TFTP protocol
bootvx - Boot vxWorks from an ELF image
cmp - memory compare
coninfo - print console devices and information
cp - memory copy
crc32 - checksum calculation
datachk - data validation using the MD5 hash
dhcp - invoke DHCP client to obtain IP/boot params
echo - echo args to console
erase - erase FLASH memory
ethreg - S26 PHY Reg rd/wr utility
exit - exit script
flashit - batch write data into flash via network using TFTP protocol
flinfo - print FLASH memory information
go - start application at address 'addr'
help - print online help
iminfo - print header information for application image
itest - return true/false on integer compare
loadb - load binary file over serial line (kermit mode)
loads - load S-Record file over serial line
loady - load binary file over serial line (ymodem mode)
loop - infinite loop on address range
md - memory display
mii - MII utility commands
mm - memory modify (auto-incrementing)
mtest - simple RAM test
mw - memory write (fill)
nfs - boot image via network using NFS protocol
nm - memory modify (constant address)
pci - list and access PCI Configuration Space
ping - send ICMP ECHO_REQUEST to network host
pll cpu-pll dither ddr-pll dither - Set to change CPU & DDR speed
pll erase
pll get
printenv- print environment variables
progmac - Set ethernet MAC addresses
protect - enable or disable FLASH write protection
rarpboot- boot image via network using RARP/TFTP protocol
reset - Perform RESET of the CPU
run - run commands in an environment variable
saveenv - save environment variables to persistent storage
setenv - set environment variables
sleep - delay execution for some time
srifpll cpu-pll ddr-pll - To change CPU & DDR speed through srif
srifpll erase
srifpll get
test - minimal test like /bin/sh
tftpboot- boot image via network using TFTP protocol
version - print monitor version
ar7240>
中断启动信息
Wasp 1.2
wasp_ddr_initial_config(249): (32bit) ddr2 init
wasp_ddr_initial_config(426): Wasp ddr init done
Tap value selected = 0xa [0x0 - 0x15]
Setting 0xb8116290 to 0x44882d0f
128 MB
Top of RAM usable for U-Boot at: 88000000
Reserving 230k for U-Boot at: 87fc4000
Reserving 192k for malloc() at: 87f94000
Reserving 44 Bytes for Board Info at: 87f93fd4
Reserving 36 Bytes for Global Data at: 87f93fb0
Reserving 128k for boot params() at: 87f73fb0
Stack Pointer at: 87f73f98
Now running in RAM - U-Boot at: 87fc4000
Flash Manuf Id 0xc2, DeviceId0 0x20, DeviceId1 0x18
flash size 16MB, sector count = 256
Flash: 16 MB
*** Warning *** : PCIe WLAN Module not found !!!
In: serial
Out: serial
Err: serial
Net: ag934x_enet_initialize...
Fetching MAC Address from 0x87feb738
wasp reset mask:c03300
WASP ----> S17 PHY *
: cfg1 0x80000000 cfg2 0x7114
eth0: 00:90:7f:b0:a4:eb
athrs17_reg_init: complete
eth0 up
eth0
eth_set_enetaddr(num=0, addr=00:90:7f:b0:a4:eb)
Setting new HW address on eth0
New Address is 00:90:7F:B0:A4:EB
eth_set_enetaddr(num=0, addr=00:90:7f:b0:a4:eb)
Setting new HW address on eth0
New Address is 00:90:7F:B0:A4:EB
Hit any key to stop autoboot: 0
Validating MD5Sum of 'vmlinux'... Passed!
Validating MD5Sum of 'rootfs'... Passed!
## Booting image at 9f0a0000 ...
Image Name: MIPS OpenWrt Linux-2.6.31
Created: 2013-02-06 2:43:24 UTC
Image Type: MIPS Linux Kernel Image (lzma compressed)
Data Size: 809689 Bytes = 790.7 kB
Load Address: 80060000
Entry Point: 80060000
Verifying Checksum at 0x9f0a0040 ...OK
Uncompressing Kernel Image ... OK
No initrd
## Transferring control to Linux (at address 80060000) ...
## Giving linux memsize in bytes, 134217728
Starting kernel ...
Booting Atheros AR934x
Linux version 2.6.31 (ubuntu@Ubuntu) (gcc version 4.3.3 (GCC) ) #1 Wed Feb 6 10:43:19 CST 2013
flash_size passed from bootloader = 16
arg 1: console=ttyS0,115200
arg 2: root=31:04
arg 3: rootfstype=squashfs
arg 4: init=/etc/preinit
arg 5: mtdparts=ath-nor0:256k(u-boot),64k(u-boot-env),320k(custom),1536k(kernel),12096k(rootfs),2048k(failsafe),64k(ART)
arg 6: board=AP100
arg 7: mem=128M
CPU revision is: 0001974c (MIPS 74Kc)
ath_sys_frequency: cpu srif ddr srif cpu 560 ddr 450 ahb 225
Determined physical RAM map:
memory: 02000000 @ 00000000 (usable)
User-defined physical RAM map:
memory: 08000000 @ 00000000 (usable)
Initrd not found or empty - disabling initrd
Zone PFN ranges:
Normal 0x00000000 -> 0x00008000
Movable zone start PFN for each node
early_node_map[1] active PFN ranges
0: 0x00000000 -> 0x00008000
Built 1 zonelists in Zone order, mobility grouping on. Total pages: 32512
Kernel command line: console=ttyS0,115200 root=31:04 rootfstype=squashfs init=/etc/preinit mtdparts=ath-nor0:256k(u-boot),64k(u-boot-env),320k(custom),1536k(kernel),12096k(rootfs),2048k(failsafe),64k(ART) board=AP100 mem=128M
PID hash table entries: 512 (order: 9, 2048 bytes)
Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes
Writing ErrCtl register=00000000
Readback ErrCtl register=00000000
Memory: 126948k/131072k available (1769k kernel code, 3940k reserved, 441k data, 128k init, 0k highmem)
SLUB: Genslabs=13, HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
Hierarchical RCU implementation.
NR_IRQS:128
plat_time_init: plat time init done
Calibrating delay loop... 279.55 BogoMIPS (lpj=559104)
Mount-cache hash table entries: 512
NET: Registered protocol family 16
***** Warning *****: PCIe WLAN H/W not found !!!
bio: create slab <bio-0> at 0
NET: Registered protocol family 2
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
TCP established hash table entries: 4096 (order: 3, 32768 bytes)
TCP bind hash table entries: 4096 (order: 2, 16384 bytes)
TCP: Hash tables configured (established 4096 bind 4096)
TCP reno registered
NET: Registered protocol family 1
ATH GPIOC major 0
squashfs: version 4.0 (2009/01/31) Phillip Lougher
Registering mini_fo version $Id$
JFFS2 version 2.2 (ZLIB) (RTIME) (c) 2001-2006 Red Hat, Inc.
msgmni has been set to 248
io scheduler noop registered
io scheduler deadline registered (default)
Serial: 8250/16550 driver, 1 ports, IRQ sharing disabled
serial8250.0: ttyS0 at MMIO 0xb8020000 (irq = 19) is a 16550A
console [ttyS0] enabled
loop: module loaded
7 cmdlinepart partitions found on MTD device ath-nor0
Creating 7 MTD partitions on "ath-nor0":
0x000000000000-0x000000040000 : "u-boot"
0x000000040000-0x000000050000 : "u-boot-env"
0x000000050000-0x0000000a0000 : "custom"
0x0000000a0000-0x000000220000 : "kernel"
0x000000220000-0x000000df0000 : "rootfs"
mtd: partition "rootfs" set to be root filesystem
mtd: partition "rootfs_data" created automatically, ofs=6C0000, len=730000
0x0000006c0000-0x000000df0000 : "rootfs_data"
0x000000df0000-0x000000ff0000 : "failsafe"
0x000000ff0000-0x000001000000 : "ART"
nf_conntrack version 0.5.0 (2048 buckets, 8192 max)
CONFIG_NF_CT_ACCT is deprecated and will be removed soon. Please use
nf_conntrack.acct=1 kernel parameter, acct=1 nf_conntrack module option or
sysctl net.netfilter.nf_conntrack_acct=1 to enable it.
ip_tables: (C) 2000-2006 Netfilter Core Team
TCP cubic registered
NET: Registered protocol family 17
Bridge firewalling registered
802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>
All bugs added by David S. Miller <davem@redhat.com>
athwdt_init: Registering WDT success
ath_otp_init: Registering OTP success
ath_clksw_init: Registering Clock Switch Interface success
VFS: Mounted root (squashfs filesystem) readonly on device 31:4.
Freeing unused kernel memory: 128k freed
Please be patient, while OpenWrt loads ...
- preinit -
Press f<ENTER> to enter failsafe mode
- regular preinit -
switching to jffs2
mini_fo: using base directory: /
mini_fo: using storage directory: /jffs
- init -
Please press Enter to activate this console. ATHR_GMAC: Length per segment 1536
ATHR_GMAC: fifo cfg 3 01f00140
ATHR_GMAC: RX TASKLET - Pkts per Intr:100
ATHR_GMAC: Mac address for unit 0:bfff0000
ATHR_GMAC: 00:90:7f:b0:a4:eb
ATHR_GMAC: Max segments per packet : 1
ATHR_GMAC: Max tx descriptor count : 128
ATHR_GMAC: Max rx descriptor count : 128
ATHR_GMAC: Mac capability flags : 2381
athr_gmac_ring_alloc Allocated 2048 at 0x8783d800
athr_gmac_ring_alloc Allocated 2048 at 0x8783e000
WASP ----> S17 PHY *
Setting Drop CRC Errors, Pause Frames and Length Error frames
athrs17_reg_init:done
Setting PHY...
Phy setup Complete
[az] 802.3az init done..
PPP generic driver version 2.4.2
NET: Registered protocol family 24
PPPoL2TP kernel driver, V1.0
p p t p driver version 0.8.4
ipt_TRIGGER: module license 'unspecified' taints kernel.
Disabling lock debugging due to kernel taint
IMQ driver loaded successfully.
Hooking IMQ before NAT on PREROUTING.
Hooking IMQ after NAT on POSTROUTING.
xt_time: kernel timezone is -0000
nf_conntrack_rtsp v0.6.21 loading
nf_nat_rtsp v0.6.21 loading
ip_set version 4 loaded
athr_gmac_ring_free Freeing at 0x8783d800
athr_gmac_ring_free Freeing at 0x8783e000
arp_tables: (C) 2002 David S. Miller
athr_gmac_ring_alloc Allocated 2048 at 0x87ac6000
athr_gmac_ring_alloc Allocated 2048 at 0x87ac5800
WASP ----> S17 PHY *
Setting Drop CRC Errors, Pause Frames and Length Error frames
athrs17_reg_init:done
Setting PHY...
Phy setup Complete
[az] 802.3az init done..
Ebtables v2.0 registered
device eth0 entered promiscuous mode
Enet:0 port0 up
ATH_MAC_TIMER: enet unit:0 is up...
RGMii 100Mbps full duplex
ATH_MAC_TIMER: done cfg2 0x7115 ifctl 0x10000 miictrl
br-lan: port 1(eth0) entering forwarding state
ath_hal: 0.9.17.1 (AR5416, AR9380, DEBUG, REGOPS_FUNC, WRITE_EEPROM, 11D)
ath_rate_atheros: Copyright (c) 2001-2005 Atheros Communications, Inc, All Rights Reserved
ath_dfs: Version 2.0.0
Copyright (c) 2005-2006 Atheros Communications, Inc. All Rights Reserved
ath_dev: Copyright (c) 2001-2007 Atheros Communications, Inc, All Rights Reserved
ath_ahb: 9.2.0_U10.5.13 (Atheros/multi-bss)
__ath_attach: Set global_scn[0]
ACBKMinfree = 48
ACBEMinfree = 32
ACVIMinfree = 16
ACVOMinfree = 0
CABMinfree = 48
UAPSDMinfree = 0
Bootstrap clock 25MHz
Wasp Enterprise mode: 0x00000000
ar9300RadioAttach: Need analog access recipe!!
Restoring Cal data from Flash
Unknown OP flag!
Unknown OP flag!
Unknown OP flag!
Unknown OP flag!
Unknown OP flag!
Unknown OP flag!
Unknown OP flag!
Unknown OP flag!
Unknown OP flag!
dfs_attach: use DFS enhancements
DFS min filter rssiThresh = 18
DFS max pulse dur = 151 ticks
ath_get_caps[5156] rx chainmask mismatch actual 3 sc_chainmak 0
ath_get_caps[5131] tx chainmask mismatch actual 3 sc_chainmak 0
wifi0: Atheros 9340: mem=0xb8100000, irq=2
Unknown OP flag!
Unknown OP flag!
Unknown OP flag!
Unknown OP flag!
Unknown OP flag!
Unknown OP flag!
Unknown OP flag!
Unknown OP flag!
Unknown OP flag!
===UDHCPC-Event deconfig
|
|
简体中文
繁體中文
English
日本語
Deutsch
한국 사람
بالعربية
TÜRKÇE
português
คนไทย
IP卡
狗仔卡
发表于 2020-2-12 14:32
置顶卡
沉默卡
喧嚣卡
顶贴卡
显身卡
