|
|
本帖最后由 mury 于 2020-2-16 16:44 编辑
用dir-885l的dts编译了一个dir-890l的lede固件，在编译时已经把usb相关的驱动都编译进去了，usb2.0接口还是无法使用。请高手麻烦指点一下问题所在。以下是ttl信息：
Digital core power voltage set to 1.0V
SVN revision: 1123
Decompressing...done
Digital core power voltage set to 1.0V
R 1.13
07DC06011801080000000000001A103F01000000
S300001BB
00001220
00000004
00000029
0000002000000019
SVN revision: 1123
Decompressing...done
NOR flash size is 32MB, limit it to 2MB
Found a ST compatible (Marconix) serial flash with 512 64KB blocks; total size 2MB
CFE version 6.30.163.18 (r377098) based on BBP 1.0.37 for BCM947XX (32bit,SP,)
Build Date: Thu Nov 20 15:51:51 CST 2014 (michael_lee@Landrover)
Copyright (C) 2000-2008 Broadcom Corporation.
Init Arena
Init Devs.
Boot partition size = 262144(0x40000)
Found a AMD NAND flash:
Total size: 128MB
Block size: 128KB
Page Size: 2048B
OOB Size: 64B
Sector size: 512B
Spare size: 16B
ECC level: 1-bit
Device ID: 0x01 0xf1 0x80 0x1d 0x01
DDR Clock: 800 MHz
Info: DDR frequency set from clkfreq=1000,*800*
et0: Broadcom BCM47XX 10/100/1000 Mbps Ethernet Controller 6.30.163.18 (r377098)
CPU type 0x0: 1000MHz
Tot mem: 262144 KBytes
CFE mem: 0x00F00000 - 0x01096904 (1665284)
Data: 0x00F5D7B4 - 0x00F5E7B0 (4092)
BSS: 0x00F5E7C0 - 0x00F94904 (221508)
Heap: 0x00F94904 - 0x01094904 (1048576)
Stack: 0x01094904 - 0x01096904 (8192)
Text: 0x00F00000 - 0x00F507CC (329676)
Boot: 0x01097000 - 0x010D7000
Reloc: I:00000000 - D:00000000
Board Name: WRGAC36
SVN revision: 1123
We disable the arp for self.
emergency web server running ...
We disable the arp for self.
Device eth0: hwaddr 00-94-5C-13-A0-01, ipaddr 192.168.0.1, mask 255.255.255.0
gateway not set, nameserver not set
[ALPHA] PRESS Ctrl-C TO ENTER EMERGENCY MODE ...
Loader:raw Filesys:tftp Dev:eth0 File:: Options null)
Loading: Failed.
Could not load :: Timeout occured
Dest=00008000, source =02000000, filename=nflash1.trx
verify_seama: data=0x02000000, size=4194304
SEAMA ==========================================
magic : 5ea3a417
meta size : 36 bytes
meta data : dev=/dev/mtdblock/7
meta data : type=firmware
meta data :
meta data :
image size : 4194240 bytes
verify_seama: signature=[(null)], type=[firmware]
checksum : FBD8398850D922268AF612F8F5403EDD
digest : FBD8398850D922268AF612F8F5403EDD
Selected !!!
================================================
seama check OK!!
insize = 2097152, out size =8388608
uncompressed size = 1930979
lzma decompress success !
Closing network.
emergency web server closing ...
Starting program at 0x00008000
Uncompressing Linux... done, booting the kernel.
[ 0.000000] Booting Linux on physical CPU 0x0
[ 0.000000] Linux version 4.14.169 (q@q-virtual-machine) (gcc version 7.5.0 (OpenWrt GCC 7.5.0 r1940-464fb0c1)) #0 SMP Tue Feb 11 09:26:50 2020
[ 0.000000] CPU: ARMv7 Processor [413fc090] revision 0 (ARMv7), cr=10c5387d
[ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
[ 0.000000] OF: fdt: Machine model: D-Link DIR-890L
[ 0.000000] earlycon: ns16550 at MMIO 0x18000300 (options '115200n8')
[ 0.000000] bootconsole [ns16550] enabled
[ 0.000000] Memory policy: Data cache writealloc
[ 0.000000] Hit pending asynchronous external abort (FSR=0x00001c06) during first unmask, this is most likely caused by a firmware/bootloader bug.
[ 0.000000] random: get_random_bytes called from start_kernel+0x90/0x3f4 with crng_init=0
[ 0.000000] percpu: Embedded 14 pages/cpu s26444 r8192 d22708 u57344
[ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 130784
[ 0.000000] Kernel command line: console=ttyS0,115200 earlycon
[ 0.000000] PID hash table entries: 512 (order: -1, 2048 bytes)
[ 0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
[ 0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
[ 0.000000] Memory: 511772K/524288K available (4203K kernel code, 129K rwdata, 1036K rodata, 1024K init, 284K bss, 12516K reserved, 0K cma-reserved, 393216K highmem)
[ 0.000000] Virtual kernel memory layout:
[ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB)
[ 0.000000] fixmap : 0xffc00000 - 0xfff00000 (3072 kB)
[ 0.000000] vmalloc : 0xc8800000 - 0xff800000 ( 880 MB)
[ 0.000000] lowmem : 0xc0000000 - 0xc8000000 ( 128 MB)
[ 0.000000] pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB)
[ 0.000000] modules : 0xbf000000 - 0xbfe00000 ( 14 MB)
[ 0.000000] .text : 0xc0008000 - 0xc051ace8 (5196 kB)
[ 0.000000] .init : 0xc0700000 - 0xc0800000 (1024 kB)
[ 0.000000] .data : 0xc0800000 - 0xc0820440 ( 130 kB)
[ 0.000000] .bss : 0xc0820440 - 0xc08677c8 ( 285 kB)
[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=2, Nodes=1
[ 0.000000] Hierarchical RCU implementation.
[ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16
[ 0.000000] L2C: DT/platform modifies aux control register: 0x0a130000 -> 0x0a530000
[ 0.000000] L2C-310 enabling early BRESP for Cortex-A9
[ 0.000000] L2C-310 full line of zeros enabled for Cortex-A9
[ 0.000000] L2C-310 ID prefetch enabled, offset 1 lines
[ 0.000000] L2C-310 dynamic clock gating enabled, standby mode enabled
[ 0.000000] L2C-310 cache controller enabled, 16 ways, 256 kB
[ 0.000000] L2C-310: CACHE_ID 0x410000c8, AUX_CTRL 0x7e530001
[ 0.000011] sched_clock: 64 bits at 500MHz, resolution 2ns, wraps every 4398046511103ns
[ 0.008136] clocksource: arm_global_timer: mask: 0xffffffffffffffff max_cycles: 0xe6a171a037, max_idle_ns: 881590485102 ns
[ 0.019346] Switching to timer-based delay loop, resolution 2ns
[ 0.025578] Calibrating delay loop (skipped), value calculated using timer frequency.. 1000.00 BogoMIPS (lpj=5000000)
[ 0.036375] pid_max: default: 32768 minimum: 301
[ 0.041161] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.047876] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.055598] CPU: Testing write buffer coherency: ok
[ 0.060563] CPU0: Spectre v2: using BPIALL workaround
[ 0.065960] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000
[ 0.072004] Setting up static identity map for 0x100000 - 0x10003c
[ 0.078407] Hierarchical SRCU implementation.
[ 0.083214] smp: Bringing up secondary CPUs ...
[ 0.088503] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001
[ 0.088509] CPU1: Spectre v2: using BPIALL workaround
[ 0.099486] smp: Brought up 1 node, 2 CPUs
[ 0.103640] SMP: Total of 2 processors activated (2000.00 BogoMIPS).
[ 0.110110] CPU: WARNING: CPU(s) started in wrong/inconsistent modes (primary CPU mode 0x13)
[ 0.118693] CPU: This may indicate a broken bootloader or firmware.
[ 0.127061] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[ 0.137084] futex hash table entries: 512 (order: 3, 32768 bytes)
[ 0.143428] pinctrl core: initialized pinctrl subsystem
[ 0.149094] NET: Registered protocol family 16
[ 0.154232] DMA: preallocated 256 KiB pool for atomic coherent allocations
[ 0.171241] clocksource: Switched to clocksource arm_global_timer
[ 0.178544] NET: Registered protocol family 2
[ 0.183424] TCP established hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.190539] TCP bind hash table entries: 1024 (order: 1, 8192 bytes)
[ 0.197013] TCP: Hash tables configured (established 1024 bind 1024)
[ 0.203548] UDP hash table entries: 256 (order: 1, 8192 bytes)
[ 0.209502] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes)
[ 0.216020] NET: Registered protocol family 1
[ 0.221283] Crashlog allocated RAM at address 0x3f00000
[ 0.226807] workingset: timestamp_bits=14 max_order=17 bucket_order=3
[ 0.236983] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 0.242975] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[ 0.255598] bounce: pool size: 64 pages
[ 0.259513] io scheduler noop registered
[ 0.263487] io scheduler deadline registered (default)
[ 0.269725] Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled
[ 0.276814] console [ttyS0] disabled
[ 0.280489] 18000300.serial: ttyS0 at MMIO 0x18000300 (irq = 18, base_baud = 7812500) is a 16550
[ 0.289468] console [ttyS0] enabled
[ 0.289468] console [ttyS0] enabled
[ 0.296522] bootconsole [ns16550] disabled
[ 0.296522] bootconsole [ns16550] disabled
[ 0.306067] nand: device found, Manufacturer ID: 0x01, Chip ID: 0xf1
[ 0.312440] nand: AMD/Spansion S34ML01G2
[ 0.316408] nand: 128 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 64
[ 0.324014] iproc_nand 18028000.nand: detected 128MiB total, 128KiB blocks, 2KiB pages, 16B OOB, 8-bit, BCH-1
[ 0.333966] nand: WARNING: brcmnand.0: the ECC used on your system is too weak compared to the one required by the NAND chip
[ 0.345223] Scanning device for bad blocks
[ 0.368342] random: fast init done
[ 0.973499] 1 fixed-partitions partitions found on MTD device brcmnand.0
[ 0.980239] Creating 1 MTD partitions on "brcmnand.0":
[ 0.985393] 0x000000000000-0x000008000000 : "firmware"
[ 0.992394] 2 seama-fw partitions found on MTD device firmware
[ 0.998286] Creating 2 MTD partitions on "firmware":
[ 1.003264] 0x000000000040-0x000000400000 : "kernel"
[ 1.008892] 0x000000400000-0x000008000000 : "ubi"
[ 1.015123] bcm_iproc 18029200.spi: using bspi-mspi mode
[ 1.021430] m25p80 spi0.0: mx25l25635e (32768 Kbytes)
[ 1.334197] 2 bcm47xxpart partitions found on MTD device spi0.0
[ 1.340152] Creating 2 MTD partitions on "spi0.0":
[ 1.344965] 0x000000000000-0x0000001f0000 : "boot"
[ 1.350411] 0x0000001f0000-0x000002000000 : "nvram"
[ 1.356535] libphy: iProc MDIO bus: probed
[ 1.360663] iproc-mdio 18003000.mdio: Broadcom iProc MDIO bus at 0xc88b7000
[ 1.367954] libphy: mdio_mux: probed
[ 1.372247] libphy: Fixed MDIO Bus: probed
[ 1.376463] bgmac_bcma: Broadcom 47xx GBit MAC driver loaded
[ 1.382523] bcma-host-soc 18000000.axi: bus0: Found chip with id 53010, rev 0x00 and package 0x00
[ 1.391506] bcma-host-soc 18000000.axi: bus0: Core 0 found: ChipCommon (manuf 0x4BF, id 0x800, rev 0x2A, class 0x0)
[ 1.402116] bcma-host-soc 18000000.axi: bus0: Core 1 found: Chipcommon B (manuf 0x4BF, id 0x50B, rev 0x01, class 0x0)
[ 1.412885] bcma-host-soc 18000000.axi: bus0: Core 2 found: DMA (manuf 0x4BF, id 0x502, rev 0x01, class 0x0)
[ 1.422898] bcma-host-soc 18000000.axi: bus0: Core 3 found: GBit MAC (manuf 0x4BF, id 0x82D, rev 0x05, class 0x0)
[ 1.433335] bcma-host-soc 18000000.axi: bus0: Core 4 found: GBit MAC (manuf 0x4BF, id 0x82D, rev 0x05, class 0x0)
[ 1.443770] bcma-host-soc 18000000.axi: bus0: Core 5 found: GBit MAC (manuf 0x4BF, id 0x82D, rev 0x05, class 0x0)
[ 1.454232] bcma-host-soc 18000000.axi: bus0: Core 6 found: GBit MAC (manuf 0x4BF, id 0x82D, rev 0x05, class 0x0)
[ 1.464622] bcma-host-soc 18000000.axi: bus0: Core 7 found: PCIe Gen 2 (manuf 0x4BF, id 0x501, rev 0x01, class 0x0)
[ 1.475203] bcma-host-soc 18000000.axi: bus0: Core 8 found: PCIe Gen 2 (manuf 0x4BF, id 0x501, rev 0x01, class 0x0)
[ 1.485792] bcma-host-soc 18000000.axi: bus0: Core 9 found: PCIe Gen 2 (manuf 0x4BF, id 0x501, rev 0x01, class 0x0)
[ 1.496401] bcma-host-soc 18000000.axi: bus0: Core 10 found: ARM Cortex A9 core (ihost) (manuf 0x4BF, id 0x510, rev 0x01, class 0x0)
[ 1.508470] bcma-host-soc 18000000.axi: bus0: Core 11 found: USB 2.0 (manuf 0x4BF, id 0x504, rev 0x01, class 0x0)
[ 1.518887] bcma-host-soc 18000000.axi: bus0: Core 12 found: USB 3.0 (manuf 0x4BF, id 0x505, rev 0x01, class 0x0)
[ 1.529310] bcma-host-soc 18000000.axi: bus0: Core 13 found: SDIO3 (manuf 0x4BF, id 0x503, rev 0x01, class 0x0)
[ 1.539550] bcma-host-soc 18000000.axi: bus0: Core 14 found: I2S (manuf 0x4BF, id 0x834, rev 0x03, class 0x0)
[ 1.549618] bcma-host-soc 18000000.axi: bus0: Core 15 found: ARM Cortex A9 JTAG (manuf 0x4BF, id 0x506, rev 0x01, class 0x0)
[ 1.561006] bcma-host-soc 18000000.axi: bus0: Core 16 found: Denali DDR2/DDR3 memory controller (manuf 0x4BF, id 0x507, rev 0x01, class 0x0)
[ 1.573773] bcma-host-soc 18000000.axi: bus0: Core 17 found: ROM (manuf 0x4BF, id 0x508, rev 0x01, class 0x0)
[ 1.583862] bcma-host-soc 18000000.axi: bus0: Core 18 found: NAND flash controller (manuf 0x4BF, id 0x509, rev 0x01, class 0x0)
[ 1.595517] bcma-host-soc 18000000.axi: bus0: Core 19 found: SPI flash controller (manuf 0x4BF, id 0x50A, rev 0x01, class 0x0)
[ 1.606962] bcma-host-soc 18000000.axi: bus0: Flash type not supported
[ 1.633584] bgmac_bcma bcma0:3: Found PHY addr: 30 (NOREGS)
[ 1.639202] bgmac_bcma bcma0:3: Support for Roboswitch not implemented
[ 1.649591] b53_common: found switch: BCM53012, rev 5
[ 1.655332] bgmac_bcma bcma0:4: Found PHY addr: 0
[ 1.660074] bgmac_bcma bcma0:4: Support for Roboswitch not implemented
[ 1.666620] bgmac_bcma bcma0:4: Invalid MAC addr: 00:00:00:00:00:00
[ 1.672915] bgmac_bcma bcma0:4: Using random MAC: 3a:fb:1f:a0:b5:0b
[ 1.680464] bgmac_bcma bcma0:5: Found PHY addr: 0
[ 1.685194] bgmac_bcma bcma0:5: Support for Roboswitch not implemented
[ 1.691893] bgmac_bcma bcma0:5: Invalid MAC addr: 00:00:00:00:00:00
[ 1.698182] bgmac_bcma bcma0:5: Using random MAC: 5a:34:d6:d7:7b:61
[ 1.705735] bgmac_bcma bcma0:6: Unsupported core_unit 3
[ 1.711053] bgmac_bcma: probe of bcma0:6 failed with error -524
[ 1.838516] pcie_iproc_bcma bcma0:7: link: UP
[ 1.842991] pcie_iproc_bcma bcma0:7: PCI host bridge to bus 0000:00
[ 1.849303] pci_bus 0000:00: root bus resource [mem 0x08000000-0x0fffffff]
[ 1.856192] pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff]
[ 1.864179] pci_bus 0000:00: 2-byte config write to 0000:00:00.0 offset 0x4 may corrupt adjacent RW1C bits
[ 1.873872] pci_bus 0000:00: 2-byte config write to 0000:00:00.0 offset 0x4 may corrupt adjacent RW1C bits
[ 1.883609] pci_bus 0000:00: 2-byte config write to 0000:00:00.0 offset 0x4c may corrupt adjacent RW1C bits
[ 1.893525] pci_bus 0000:00: 2-byte config write to 0000:00:00.0 offset 0x3e may corrupt adjacent RW1C bits
[ 1.903306] pci_bus 0000:00: 2-byte config write to 0000:00:00.0 offset 0x4 may corrupt adjacent RW1C bits
[ 1.912996] pci_bus 0000:00: 1-byte config write to 0000:00:00.0 offset 0xc may corrupt adjacent RW1C bits
[ 1.922677] PCI: bus0: Fast back to back transfers disabled
[ 1.928262] pci 0000:00:00.0: bridge configuration invalid ([bus 00-00]), reconfiguring
[ 1.936295] pci_bus 0000:00: 2-byte config write to 0000:00:00.0 offset 0x3e may corrupt adjacent RW1C bits
[ 1.946070] pci_bus 0000:00: 2-byte config write to 0000:00:00.0 offset 0xc8 may corrupt adjacent RW1C bits
[ 1.955844] pci_bus 0000:00: 2-byte config write to 0000:00:00.0 offset 0x3e may corrupt adjacent RW1C bits
[ 1.965624] pci_bus 0000:00: 2-byte config write to 0000:00:00.0 offset 0x3e may corrupt adjacent RW1C bits
[ 1.975818] PCI: bus1: Fast back to back transfers disabled
[ 1.981430] pci 0000:01:00.0: bridge configuration invalid ([bus 00-00]), reconfiguring
[ 1.989634] pci 0000:02:00.0: unknown header type 12, ignoring device
[ 1.996776] pci 0000:02:03.0: [Firmware Bug]: reg 0x10: invalid BAR (can't size)
[ 2.004229] pci 0000:02:03.0: [Firmware Bug]: reg 0x14: invalid BAR (can't size)
[ 2.011665] pci 0000:02:03.0: [Firmware Bug]: reg 0x18: invalid BAR (can't size)
[ 2.019095] pci 0000:02:03.0: [Firmware Bug]: reg 0x1c: invalid BAR (can't size)
[ 2.026522] pci 0000:02:03.0: [Firmware Bug]: reg 0x20: invalid BAR (can't size)
[ 2.033953] pci 0000:02:03.0: [Firmware Bug]: reg 0x24: invalid BAR (can't size)
[ 2.041553] pci 0000:02:04.0: [Firmware Bug]: reg 0x10: invalid BAR (can't size)
[ 2.048992] pci 0000:02:04.0: [Firmware Bug]: reg 0x14: invalid BAR (can't size)
[ 2.056420] pci 0000:02:04.0: [Firmware Bug]: reg 0x18: invalid BAR (can't size)
[ 2.063852] pci 0000:02:04.0: [Firmware Bug]: reg 0x1c: invalid BAR (can't size)
[ 2.071284] pci 0000:02:04.0: [Firmware Bug]: reg 0x20: invalid BAR (can't size)
[ 2.078716] pci 0000:02:04.0: [Firmware Bug]: reg 0x24: invalid BAR (can't size)
[ 2.086330] pci 0000:02:05.0: [Firmware Bug]: reg 0x10: invalid BAR (can't size)
[ 2.093781] pci 0000:02:05.0: [Firmware Bug]: reg 0x14: invalid BAR (can't size)
[ 2.101214] pci 0000:02:05.0: [Firmware Bug]: reg 0x18: invalid BAR (can't size)
[ 2.108644] pci 0000:02:05.0: [Firmware Bug]: reg 0x1c: invalid BAR (can't size)
[ 2.116075] pci 0000:02:05.0: [Firmware Bug]: reg 0x20: invalid BAR (can't size)
[ 2.123511] pci 0000:02:05.0: [Firmware Bug]: reg 0x24: invalid BAR (can't size)
[ 2.131116] pci 0000:02:06.0: [Firmware Bug]: reg 0x10: invalid BAR (can't size)
[ 2.138557] pci 0000:02:06.0: [Firmware Bug]: reg 0x14: invalid BAR (can't size)
[ 2.145985] pci 0000:02:06.0: [Firmware Bug]: reg 0x18: invalid BAR (can't size)
[ 2.153418] pci 0000:02:06.0: [Firmware Bug]: reg 0x1c: invalid BAR (can't size)
[ 2.160852] pci 0000:02:06.0: [Firmware Bug]: reg 0x20: invalid BAR (can't size)
[ 2.168275] pci 0000:02:06.0: [Firmware Bug]: reg 0x24: invalid BAR (can't size)
[ 2.175888] pci 0000:02:07.0: [Firmware Bug]: reg 0x10: invalid BAR (can't size)
[ 2.183335] pci 0000:02:07.0: [Firmware Bug]: reg 0x14: invalid BAR (can't size)
[ 2.190768] pci 0000:02:07.0: [Firmware Bug]: reg 0x18: invalid BAR (can't size)
[ 2.198190] pci 0000:02:07.0: [Firmware Bug]: reg 0x1c: invalid BAR (can't size)
[ 2.205623] pci 0000:02:07.0: [Firmware Bug]: reg 0x20: invalid BAR (can't size)
[ 2.213054] pci 0000:02:07.0: [Firmware Bug]: reg 0x24: invalid BAR (can't size)
[ 2.220656] pci 0000:02:08.0: [Firmware Bug]: reg 0x10: invalid BAR (can't size)
[ 2.228082] pci 0000:02:08.0: [Firmware Bug]: reg 0x14: invalid BAR (can't size)
[ 2.235523] pci 0000:02:08.0: [Firmware Bug]: reg 0x18: invalid BAR (can't size)
[ 2.242954] pci 0000:02:08.0: [Firmware Bug]: reg 0x1c: invalid BAR (can't size)
[ 2.250387] pci 0000:02:08.0: [Firmware Bug]: reg 0x20: invalid BAR (can't size)
[ 2.257813] pci 0000:02:08.0: [Firmware Bug]: reg 0x24: invalid BAR (can't size)
[ 2.265420] pci 0000:02:09.0: [Firmware Bug]: reg 0x10: invalid BAR (can't size)
[ 2.272860] pci 0000:02:09.0: [Firmware Bug]: reg 0x14: invalid BAR (can't size)
[ 2.280296] pci 0000:02:09.0: [Firmware Bug]: reg 0x18: invalid BAR (can't size)
[ 2.287720] pci 0000:02:09.0: [Firmware Bug]: reg 0x1c: invalid BAR (can't size)
[ 2.295152] pci 0000:02:09.0: [Firmware Bug]: reg 0x20: invalid BAR (can't size)
[ 2.302583] pci 0000:02:09.0: [Firmware Bug]: reg 0x24: invalid BAR (can't size)
[ 2.310197] pci 0000:02:0a.0: [Firmware Bug]: reg 0x10: invalid BAR (can't size)
[ 2.317628] pci 0000:02:0a.0: [Firmware Bug]: reg 0x14: invalid BAR (can't size)
[ 2.325065] pci 0000:02:0a.0: [Firmware Bug]: reg 0x18: invalid BAR (can't size)
[ 2.332503] pci 0000:02:0a.0: [Firmware Bug]: reg 0x1c: invalid BAR (can't size)
[ 2.339933] pci 0000:02:0a.0: [Firmware Bug]: reg 0x20: invalid BAR (can't size)
[ 2.347360] pci 0000:02:0a.0: [Firmware Bug]: reg 0x24: invalid BAR (can't size)
[ 2.354961] pci 0000:02:0b.0: [Firmware Bug]: reg 0x10: invalid BAR (can't size)
[ 2.362406] pci 0000:02:0b.0: [Firmware Bug]: reg 0x14: invalid BAR (can't size)
[ 2.369847] pci 0000:02:0b.0: [Firmware Bug]: reg 0x18: invalid BAR (can't size)
[ 2.377276] pci 0000:02:0b.0: [Firmware Bug]: reg 0x1c: invalid BAR (can't size)
[ 2.384707] pci 0000:02:0b.0: [Firmware Bug]: reg 0x20: invalid BAR (can't size)
[ 2.392140] pci 0000:02:0b.0: [Firmware Bug]: reg 0x24: invalid BAR (can't size)
[ 2.399750] pci 0000:02:0c.0: [Firmware Bug]: reg 0x10: invalid BAR (can't size)
[ 2.407176] pci 0000:02:0c.0: [Firmware Bug]: reg 0x14: invalid BAR (can't size)
[ 2.414612] pci 0000:02:0c.0: [Firmware Bug]: reg 0x18: invalid BAR (can't size)
[ 2.422048] pci 0000:02:0c.0: [Firmware Bug]: reg 0x1c: invalid BAR (can't size)
[ 2.429481] pci 0000:02:0c.0: [Firmware Bug]: reg 0x20: invalid BAR (can't size)
[ 2.436906] pci 0000:02:0c.0: [Firmware Bug]: reg 0x24: invalid BAR (can't size)
[ 2.444512] pci 0000:02:0d.0: [Firmware Bug]: reg 0x10: invalid BAR (can't size)
[ 2.451955] pci 0000:02:0d.0: [Firmware Bug]: reg 0x14: invalid BAR (can't size)
[ 2.459389] pci 0000:02:0d.0: [Firmware Bug]: reg 0x18: invalid BAR (can't size)
[ 2.466813] pci 0000:02:0d.0: [Firmware Bug]: reg 0x1c: invalid BAR (can't size)
[ 2.474245] pci 0000:02:0d.0: [Firmware Bug]: reg 0x20: invalid BAR (can't size)
[ 2.481678] pci 0000:02:0d.0: [Firmware Bug]: reg 0x24: invalid BAR (can't size)
[ 2.489297] pci 0000:02:0e.0: [Firmware Bug]: reg 0x10: invalid BAR (can't size)
[ 2.496722] pci 0000:02:0e.0: [Firmware Bug]: reg 0x14: invalid BAR (can't size)
[ 2.504164] pci 0000:02:0e.0: [Firmware Bug]: reg 0x18: invalid BAR (can't size)
[ 2.511595] pci 0000:02:0e.0: [Firmware Bug]: reg 0x1c: invalid BAR (can't size)
[ 2.519028] pci 0000:02:0e.0: [Firmware Bug]: reg 0x20: invalid BAR (can't size)
[ 2.526453] pci 0000:02:0e.0: [Firmware Bug]: reg 0x24: invalid BAR (can't size)
[ 2.534057] pci 0000:02:0f.0: [Firmware Bug]: reg 0x10: invalid BAR (can't size)
[ 2.541499] pci 0000:02:0f.0: [Firmware Bug]: reg 0x14: invalid BAR (can't size)
[ 2.548937] pci 0000:02:0f.0: [Firmware Bug]: reg 0x18: invalid BAR (can't size)
[ 2.556361] pci 0000:02:0f.0: [Firmware Bug]: reg 0x1c: invalid BAR (can't size)
[ 2.563793] pci 0000:02:0f.0: [Firmware Bug]: reg 0x20: invalid BAR (can't size)
[ 2.571225] pci 0000:02:0f.0: [Firmware Bug]: reg 0x24: invalid BAR (can't size)
[ 2.578838] pci 0000:02:10.0: [Firmware Bug]: reg 0x10: invalid BAR (can't size)
[ 2.586269] pci 0000:02:10.0: [Firmware Bug]: reg 0x14: invalid BAR (can't size)
[ 2.593705] pci 0000:02:10.0: [Firmware Bug]: reg 0x18: invalid BAR (can't size)
[ 2.601142] pci 0000:02:10.0: [Firmware Bug]: reg 0x1c: invalid BAR (can't size)
[ 2.608574] pci 0000:02:10.0: [Firmware Bug]: reg 0x20: invalid BAR (can't size)
[ 2.616000] pci 0000:02:10.0: [Firmware Bug]: reg 0x24: invalid BAR (can't size)
[ 2.623607] pci 0000:02:11.0: [Firmware Bug]: reg 0x10: invalid BAR (can't size)
[ 2.653465] pci 0000:02:11.0: [Firmware Bug]: reg 0x20: invalid BAR (can't size)
[ 2.660897] pci 0000:02:11.0: [Firmware Bug]: reg 0x24: invalid BAR (can't size)
[ 2.668497] pci 0000:02:12.0: [Firmware Bug]: reg 0x10: invalid BAR (can't size)
[ 2.675941] pci 0000:02:12.0: [Firmware Bug]: reg 0x14: invalid BAR (can't size)
[ 2.683374] pci 0000:02:12.0: [Firmware Bug]: reg 0x18: invalid BAR (can't size)
[ 2.690805] pci 0000:02:12.0: [Firmware Bug]: reg 0x1c: invalid BAR (can't size)
[ 2.698232] pci 0000:02:12.0: [Firmware Bug]: reg 0x20: invalid BAR (can't size)
[ 2.705663] pci 0000:02:12.0: [Firmware Bug]: reg 0x24: invalid BAR (can't size)
[ 2.713292] pci 0000:02:13.0: [Firmware Bug]: reg 0x10: invalid BAR (can't size)
[ 2.720738] pci 0000:02:13.0: [Firmware Bug]: reg 0x14: invalid BAR (can't size)
[ 2.728165] pci 0000:02:13.0: [Firmware Bug]: reg 0x18: invalid BAR (can't size)
[ 2.735598] pci 0000:02:13.0: [Firmware Bug]: reg 0x1c: invalid BAR (can't size)
[ 2.743029] pci 0000:02:13.0: [Firmware Bug]: reg 0x20: invalid BAR (can't size)
[ 2.750463] pci 0000:02:13.0: [Firmware Bug]: reg 0x24: invalid BAR (can't size)
[ 2.758065] pci 0000:02:14.0: [Firmware Bug]: reg 0x10: invalid BAR (can't size)
[ 2.765520] pci 0000:02:14.0: [Firmware Bug]: reg 0x14: invalid BAR (can't size)
[ 2.772955] pci 0000:02:14.0: [Firmware Bug]: reg 0x18: invalid BAR (can't size)
[ 2.780386] pci 0000:02:14.0: [Firmware Bug]: reg 0x1c: invalid BAR (can't size)
[ 2.787813] pci 0000:02:14.0: [Firmware Bug]: reg 0x20: invalid BAR (can't size)
[ 2.795243] pci 0000:02:14.0: [Firmware Bug]: reg 0x24: invalid BAR (can't size)
[ 2.802870] pci 0000:02:15.0: [Firmware Bug]: reg 0x10: invalid BAR (can't size)
[ 2.810310] pci 0000:02:15.0: [Firmware Bug]: reg 0x14: invalid BAR (can't size)
[ 2.817738] pci 0000:02:15.0: [Firmware Bug]: reg 0x18: invalid BAR (can't size)
[ 2.825170] pci 0000:02:15.0: [Firmware Bug]: reg 0x1c: invalid BAR (can't size)
[ 2.832602] pci 0000:02:15.0: [Firmware Bug]: reg 0x20: invalid BAR (can't size)
[ 2.840035] pci 0000:02:15.0: [Firmware Bug]: reg 0x24: invalid BAR (can't size)
[ 2.847639] pci 0000:02:16.0: [Firmware Bug]: reg 0x10: invalid BAR (can't size)
[ 2.855088] pci 0000:02:16.0: [Firmware Bug]: reg 0x14: invalid BAR (can't size)
[ 2.862519] pci 0000:02:16.0: [Firmware Bug]: reg 0x18: invalid BAR (can't size)
[ 2.869952] pci 0000:02:16.0: [Firmware Bug]: reg 0x1c: invalid BAR (can't size)
[ 2.877377] pci 0000:02:16.0: [Firmware Bug]: reg 0x20: invalid BAR (can't size)
[ 2.884809] pci 0000:02:16.0: [Firmware Bug]: reg 0x24: invalid BAR (can't size)
[ 2.892422] pci 0000:02:17.0: [Firmware Bug]: reg 0x10: invalid BAR (can't size)
[ 2.899872] pci 0000:02:17.0: [Firmware Bug]: reg 0x14: invalid BAR (can't size)
[ 2.907302] pci 0000:02:17.0: [Firmware Bug]: reg 0x18: invalid BAR (can't size)
[ 2.914735] pci 0000:02:17.0: [Firmware Bug]: reg 0x1c: invalid BAR (can't size)
[ 2.922166] pci 0000:02:17.0: [Firmware Bug]: reg 0x20: invalid BAR (can't size)
[ 2.929600] pci 0000:02:17.0: [Firmware Bug]: reg 0x24: invalid BAR (can't size)
[ 2.937212] pci 0000:02:18.0: [Firmware Bug]: reg 0x10: invalid BAR (can't size)
[ 2.944662] pci 0000:02:18.0: [Firmware Bug]: reg 0x14: invalid BAR (can't size)
[ 2.952094] pci 0000:02:18.0: [Firmware Bug]: reg 0x18: invalid BAR (can't size)
[ 2.959524] pci 0000:02:18.0: [Firmware Bug]: reg 0x1c: invalid BAR (can't size)
[ 2.966950] pci 0000:02:18.0: [Firmware Bug]: reg 0x20: invalid BAR (can't size)
[ 2.974382] pci 0000:02:18.0: [Firmware Bug]: reg 0x24: invalid BAR (can't size)
[ 2.981989] pci 0000:02:19.0: [Firmware Bug]: reg 0x10: invalid BAR (can't size)
[ 2.989429] pci 0000:02:19.0: [Firmware Bug]: reg 0x14: invalid BAR (can't size)
[ 2.996858] pci 0000:02:19.0: [Firmware Bug]: reg 0x18: invalid BAR (can't size)
[ 3.004290] pci 0000:02:19.0: [Firmware Bug]: reg 0x1c: invalid BAR (can't size)
[ 3.011722] pci 0000:02:19.0: [Firmware Bug]: reg 0x20: invalid BAR (can't size)
[ 3.019155] pci 0000:02:19.0: [Firmware Bug]: reg 0x24: invalid BAR (can't size)
[ 3.026764] pci 0000:02:1a.0: [Firmware Bug]: reg 0x10: invalid BAR (can't size)
[ 3.034214] pci 0000:02:1a.0: [Firmware Bug]: reg 0x14: invalid BAR (can't size)
[ 3.041648] pci 0000:02:1a.0: [Firmware Bug]: reg 0x18: invalid BAR (can't size)
[ 3.049080] pci 0000:02:1a.0: [Firmware Bug]: reg 0x1c: invalid BAR (can't size)
[ 3.056505] pci 0000:02:1a.0: [Firmware Bug]: reg 0x20: invalid BAR (can't size)
[ 3.063937] pci 0000:02:1a.0: [Firmware Bug]: reg 0x24: invalid BAR (can't size)
[ 3.071544] pci 0000:02:1b.0: [Firmware Bug]: reg 0x10: invalid BAR (can't size)
[ 3.078985] pci 0000:02:1b.0: [Firmware Bug]: reg 0x14: invalid BAR (can't size)
[ 3.086412] pci 0000:02:1b.0: [Firmware Bug]: reg 0x18: invalid BAR (can't size)
[ 3.093847] pci 0000:02:1b.0: [Firmware Bug]: reg 0x1c: invalid BAR (can't size)
[ 3.101278] pci 0000:02:1b.0: [Firmware Bug]: reg 0x20: invalid BAR (can't size)
[ 3.108710] pci 0000:02:1b.0: [Firmware Bug]: reg 0x24: invalid BAR (can't size)
[ 3.116318] pci 0000:02:1c.0: [Firmware Bug]: reg 0x10: invalid BAR (can't size)
[ 3.123764] pci 0000:02:1c.0: [Firmware Bug]: reg 0x14: invalid BAR (can't size)
[ 3.131195] pci 0000:02:1c.0: [Firmware Bug]: reg 0x18: invalid BAR (can't size)
[ 3.138626] pci 0000:02:1c.0: [Firmware Bug]: reg 0x1c: invalid BAR (can't size)
[ 3.146051] pci 0000:02:1c.0: [Firmware Bug]: reg 0x20: invalid BAR (can't size)
[ 3.153483] pci 0000:02:1c.0: [Firmware Bug]: reg 0x24: invalid BAR (can't size)
[ 3.161101] pci 0000:02:1d.0: [Firmware Bug]: reg 0x10: invalid BAR (can't size)
[ 3.168529] pci 0000:02:1d.0: [Firmware Bug]: reg 0x14: invalid BAR (can't size)
[ 3.175965] pci 0000:02:1d.0: [Firmware Bug]: reg 0x18: invalid BAR (can't size)
[ 3.183400] pci 0000:02:1d.0: [Firmware Bug]: reg 0x1c: invalid BAR (can't size)
[ 3.190833] pci 0000:02:1d.0: [Firmware Bug]: reg 0x20: invalid BAR (can't size)
[ 3.198258] pci 0000:02:1d.0: [Firmware Bug]: reg 0x24: invalid BAR (can't size)
[ 3.205878] pci 0000:02:1e.0: [Firmware Bug]: reg 0x10: invalid BAR (can't size)
[ 3.213327] pci 0000:02:1e.0: [Firmware Bug]: reg 0x14: invalid BAR (can't size)
[ 3.220760] pci 0000:02:1e.0: [Firmware Bug]: reg 0x18: invalid BAR (can't size)
[ 3.228183] pci 0000:02:1e.0: [Firmware Bug]: reg 0x1c: invalid BAR (can't size)
[ 3.235616] pci 0000:02:1e.0: [Firmware Bug]: reg 0x20: invalid BAR (can't size)
[ 3.243047] pci 0000:02:1e.0: [Firmware Bug]: reg 0x24: invalid BAR (can't size)
[ 3.250669] pci 0000:02:1f.0: [Firmware Bug]: reg 0x10: invalid BAR (can't size)
[ 3.258102] pci 0000:02:1f.0: [Firmware Bug]: reg 0x14: invalid BAR (can't size)
[ 3.265536] pci 0000:02:1f.0: [Firmware Bug]: reg 0x18: invalid BAR (can't size)
[ 3.272972] pci 0000:02:1f.0: [Firmware Bug]: reg 0x1c: invalid BAR (can't size)
[ 3.280405] pci 0000:02:1f.0: [Firmware Bug]: reg 0x20: invalid BAR (can't size)
[ 3.287832] pci 0000:02:1f.0: [Firmware Bug]: reg 0x24: invalid BAR (can't size)
[ 3.295645] PCI: bus2: Fast back to back transfers disabled
[ 3.301254] pci 0000:02:01.0: bridge configuration invalid ([bus 00-00]), reconfiguring
[ 3.309297] pci 0000:02:02.0: bridge configuration invalid ([bus 00-00]), reconfiguring
[ 3.317906] PCI: bus3: Fast back to back transfers disabled
[ 3.324115] PCI: bus4: Fast back to back transfers disabled
[ 3.329946] pci 0000:00:00.0: BAR 8: assigned [mem 0x08000000-0x08ffffff]
[ 3.336758] pci 0000:00:00.0: BAR 9: assigned [mem 0x09000000-0x092fffff 64bit pref]
[ 3.344540] pci 0000:01:00.0: BAR 8: assigned [mem 0x08000000-0x08dfffff]
[ 3.351354] pci 0000:01:00.0: BAR 9: assigned [mem 0x09000000-0x092fffff 64bit pref]
[ 3.359124] pci 0000:01:00.0: BAR 0: assigned [mem 0x08e00000-0x08e03fff]
[ 3.365936] pci 0000:01:00.0: BAR 7: no space for [io size 0x1000]
[ 3.372224] pci 0000:01:00.0: BAR 7: failed to assign [io size 0x1000]
[ 3.378867] pci 0000:01:00.0: BAR 7: no space for [io size 0x1000]
[ 3.385149] pci 0000:01:00.0: BAR 7: failed to assign [io size 0x1000]
[ 3.391797] pci 0000:02:01.0: BAR 8: assigned [mem 0x08000000-0x087fffff]
[ 3.398614] pci 0000:02:02.0: BAR 8: assigned [mem 0x08800000-0x08dfffff]
[ 3.405423] pci 0000:02:01.0: BAR 9: assigned [mem 0x09000000-0x091fffff 64bit pref]
[ 3.413192] pci 0000:02:01.0: BAR 7: no space for [io size 0x1000]
[ 3.419489] pci 0000:02:01.0: BAR 7: failed to assign [io size 0x1000]
[ 3.426122] pci 0000:02:01.0: BAR 7: no space for [io size 0x1000]
[ 3.432411] pci 0000:02:01.0: BAR 7: failed to assign [io size 0x1000]
[ 3.439055] pci 0000:03:00.0: BAR 2: assigned [mem 0x08000000-0x083fffff 64bit]
[ 3.446400] pci 0000:03:00.0: BAR 0: assigned [mem 0x08400000-0x08407fff 64bit]
[ 3.453751] pci 0000:02:01.0: PCI bridge to [bus 03]
[ 3.458736] pci 0000:02:01.0: bridge window [mem 0x08000000-0x087fffff]
[ 3.465541] pci 0000:02:01.0: bridge window [mem 0x09000000-0x091fffff 64bit pref]
[ 3.473319] pci 0000:04:00.0: BAR 2: assigned [mem 0x08800000-0x08bfffff 64bit]
[ 3.480678] pci 0000:04:00.0: BAR 0: assigned [mem 0x08c00000-0x08c07fff 64bit]
[ 3.488021] pci 0000:02:02.0: PCI bridge to [bus 04]
[ 3.493013] pci 0000:02:02.0: bridge window [mem 0x08800000-0x08dfffff]
[ 3.499842] pci 0000:01:00.0: PCI bridge to [bus 02-04]
[ 3.505086] pci 0000:01:00.0: bridge window [mem 0x08000000-0x08dfffff]
[ 3.511899] pci 0000:01:00.0: bridge window [mem 0x09000000-0x092fffff 64bit pref]
[ 3.519672] pci 0000:00:00.0: PCI bridge to [bus 01-04]
[ 3.524911] pci 0000:00:00.0: bridge window [mem 0x08000000-0x08ffffff]
[ 3.531723] pci 0000:00:00.0: bridge window [mem 0x09000000-0x092fffff 64bit pref]
[ 3.658576] pcie_iproc_bcma bcma0:8: link: UP
[ 3.663061] pcie_iproc_bcma bcma0:8: PCI host bridge to bus 0001:00
[ 3.669365] pci_bus 0001:00: root bus resource [mem 0x40000000-0x47ffffff]
[ 3.676255] pci_bus 0001:00: No busn resource found for root bus, will use [bus 00-ff]
[ 3.684435] PCI: bus0: Fast back to back transfers disabled
[ 3.690042] pci 0001:00:00.0: bridge configuration invalid ([bus 00-00]), reconfiguring
[ 3.698474] PCI: bus1: Fast back to back transfers disabled
[ 3.704131] pci 0001:00:00.0: BAR 8: assigned [mem 0x40000000-0x405fffff]
[ 3.710957] pci 0001:01:00.0: BAR 2: assigned [mem 0x40000000-0x403fffff 64bit]
[ 3.718299] pci 0001:01:00.0: BAR 0: assigned [mem 0x40400000-0x40407fff 64bit]
[ 3.725640] pci 0001:00:00.0: PCI bridge to [bus 01]
[ 3.730628] pci 0001:00:00.0: bridge window [mem 0x40000000-0x405fffff]
[ 3.858572] pcie_iproc_bcma bcma0:9: PHY or data link is INACTIVE!
[ 3.864774] pcie_iproc_bcma bcma0:9: no PCIe EP device detected
[ 3.870722] pcie_iproc_bcma bcma0:9: PCIe controller setup failed
[ 3.877773] bcm47xx-wdt bcm47xx-wdt.0: BCM47xx Watchdog Timer enabled (30 seconds, Software Timer)
[ 3.886819] bcma-host-soc 18000000.axi: bus0: Bus registered
[ 3.893335] NET: Registered protocol family 10
[ 3.899059] Segment Routing with IPv6
[ 3.902814] NET: Registered protocol family 17
[ 3.907305] 8021q: 802.1Q VLAN Support v1.8
[ 3.911561] Registering SWP/SWPB emulation handler
[ 3.918548] UBI: auto-attach mtd2
[ 3.921957] ubi0: attaching mtd2
[ 4.096215] random: crng init done
[ 4.589244] ubi0: scanning is finished
[ 4.602332] ubi0: attached mtd2 (name "ubi", size 124 MiB)
[ 4.607845] ubi0: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes
[ 4.614755] ubi0: min./max. I/O unit sizes: 2048/2048, sub-page size 2048
[ 4.621567] ubi0: VID header offset: 2048 (aligned 2048), data offset: 4096
[ 4.628541] ubi0: good PEBs: 992, bad PEBs: 0, corrupted PEBs: 0
[ 4.634571] ubi0: user volume: 2, internal volumes: 1, max. volumes count: 128
[ 4.641812] ubi0: max/mean erase counter: 3/1, WL threshold: 4096, image sequence number: 873633144
[ 4.650882] ubi0: available PEBs: 0, total reserved PEBs: 992, PEBs reserved for bad PEB handling: 20
[ 4.660161] ubi0: background thread "ubi_bgt0d" started, PID 437
[ 4.667085] block ubiblock0_0: created from ubi0:0(rootfs)
[ 4.672636] ubiblock: device ubiblock0_0 (rootfs) set to be root filesystem
[ 4.684075] VFS: Mounted root (squashfs filesystem) readonly on device 254:0.
[ 4.692208] Freeing unused kernel memory: 1024K
[ 4.997965] init: Console is alive
[ 5.001525] init: - watchdog -
[ 5.961577] kmodloader: loading kernel modules from /etc/modules-boot.d/*
[ 6.044238] usbcore: registered new interface driver usbfs
[ 6.049836] usbcore: registered new interface driver hub
[ 6.055241] usbcore: registered new device driver usb
[ 6.064435] ANTFS Module: Version
[ 6.070222] exFAT: Version 1.2.9
[ 6.087164] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 6.097325] SCSI subsystem initialized
[ 6.103536] ehci-platform: EHCI generic platform driver
[ 6.109953] ehci-pci: EHCI PCI platform driver
[ 6.115871] ehci-platform 18021000.ehci: EHCI Host Controller
[ 6.121718] ehci-platform 18021000.ehci: new USB bus registered, assigned bus number 1
[ 6.128080] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[ 6.129875] ehci-platform 18021000.ehci: irq 37, io mem 0x18021000
[ 6.136923] ohci-platform: OHCI generic platform driver
[ 6.147549] ohci-platform 18022000.ohci: Generic Platform OHCI controller
[ 6.154384] ohci-platform 18022000.ohci: new USB bus registered, assigned bus number 2
[ 6.162486] ohci-platform 18022000.ohci: irq 37, io mem 0x18022000
[ 6.178636] ehci-platform 18021000.ehci: USB 2.0 started, EHCI 1.00
[ 6.185537] hub 1-0:1.0: USB hub found
[ 6.189543] hub 1-0:1.0: 2 ports detected
[ 6.239987] hub 2-0:1.0: USB hub found
[ 6.243799] hub 2-0:1.0: 2 ports detected
[ 6.249396] uhci_hcd: USB Universal Host Controller Interface driver
[ 6.358580] xhci-hcd 18023000.xhci: xHCI Host Controller
[ 6.363936] xhci-hcd 18023000.xhci: new USB bus registered, assigned bus number 3
[ 6.371707] xhci-hcd 18023000.xhci: hcc params 0x02501164 hci version 0x100 quirks 0x0000001000010010
[ 6.381014] xhci-hcd 18023000.xhci: irq 38, io mem 0x18023000
[ 6.387399] hub 3-0:1.0: USB hub found
[ 6.391283] hub 3-0:1.0: config failed, hub doesn't have any ports! (err -19)
[ 6.398643] xhci-hcd 18023000.xhci: xHCI Host Controller
[ 6.403987] xhci-hcd 18023000.xhci: new USB bus registered, assigned bus number 4
[ 6.411511] xhci-hcd 18023000.xhci: Host supports USB 3.0 SuperSpeed
[ 6.428646] usb usb4: We don't know the algorithms for LPM for this host, disabling LPM.
[ 6.437226] hub 4-0:1.0: USB hub found
[ 6.441054] hub 4-0:1.0: 1 port detected
[ 6.449214] usbcore: registered new interface driver usb-storage
[ 6.456341] usbcore: registered new interface driver uas
[ 6.461877] kmodloader: done loading kernel modules from /etc/modules-boot.d/*
[ 6.475633] init: - preinit -
[ 51.828956] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 51.834889] IPv6: ADDRCONF(NETDEV_UP): eth0.1: link is not ready
Press the [f] key and hit [enter] to enter failsafe mode
Press the [1], [2], [3] or [4] key and hit [enter] to select the debug level
[ 52.915511] bgmac_bcma bcma0:3 eth0: Link is Up - 1Gbps/Full - flow control off
[ 52.922862] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[ 52.929457] IPv6: ADDRCONF(NETDEV_CHANGE): eth0.1: link becomes ready
[ 55.015592] mount_root: loading kmods from internal overlay
[ 55.039487] kmodloader: loading kernel modules from //etc/modules-boot.d/*
[ 55.047659] kmodloader: done loading kernel modules from //etc/modules-boot.d/*
[ 55.715900] UBIFS (ubi0:1): default file-system created
[ 55.722012] UBIFS (ubi0:1): background thread "ubifs_bgt0_1" started, PID 631
[ 55.794651] UBIFS (ubi0:1): UBIFS: mounted UBI device 0, volume 1, name "rootfs_data"
[ 55.802534] UBIFS (ubi0:1): LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes
[ 55.812486] UBIFS (ubi0:1): FS size: 100438016 bytes (95 MiB, 791 LEBs), journal size 5079040 bytes (4 MiB, 40 LEBs)
[ 55.823037] UBIFS (ubi0:1): reserved for root: 4743935 bytes (4632 KiB)
[ 55.829673] UBIFS (ubi0:1): media format: w4/r0 (latest is w5/r0), UUID 6E97D7D7-5FED-429C-9C30-755FC717F74C, small LPT model
[ 55.841898] block: attempting to load /tmp/ubifs_cfg/upper/etc/config/fstab
[ 55.849015] block: unable to load configuration (fstab: Entry not found)
[ 55.855779] block: attempting to load /tmp/ubifs_cfg/etc/config/fstab
[ 55.862339] block: unable to load configuration (fstab: Entry not found)
[ 55.869113] block: attempting to load /etc/config/fstab
[ 55.877885] block: unable to load configuration (fstab: Entry not found)
[ 55.884677] block: no usable configuration
[ 55.931719] UBIFS (ubi0:1): un-mount UBI device 0
[ 55.936453] UBIFS (ubi0:1): background thread "ubifs_bgt0_1" stops
[ 55.980877] UBIFS (ubi0:1): background thread "ubifs_bgt0_1" started, PID 634
[ 56.053385] UBIFS (ubi0:1): UBIFS: mounted UBI device 0, volume 1, name "rootfs_data"
[ 56.061279] UBIFS (ubi0:1): LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes
[ 56.071233] UBIFS (ubi0:1): FS size: 100438016 bytes (95 MiB, 791 LEBs), journal size 5079040 bytes (4 MiB, 40 LEBs)
[ 56.081784] UBIFS (ubi0:1): reserved for root: 4743935 bytes (4632 KiB)
[ 56.088427] UBIFS (ubi0:1): media format: w4/r0 (latest is w5/r0), UUID 6E97D7D7-5FED-429C-9C30-755FC717F74C, small LPT model
[ 56.630558] block: attempting to load /tmp/ubifs_cfg/upper/etc/config/fstab
[ 56.637626] block: unable to load configuration (fstab: Entry not found)
[ 56.644412] block: attempting to load /tmp/ubifs_cfg/etc/config/fstab
[ 56.650964] block: unable to load configuration (fstab: Entry not found)
[ 56.657723] block: attempting to load /etc/config/fstab
[ 56.663024] block: unable to load configuration (fstab: Entry not found)
[ 56.669784] block: no usable configuration
[ 56.699975] mount_root: overlay filesystem has not been fully initialized yet
[ 56.707419] mount_root: switching to ubifs overlay
[ 56.733536] urandom-seed: Seed file not found (/etc/urandom.seed)
[ 56.832571] procd: - early -
[ 56.835630] procd: - watchdog -
[ 57.438669] procd: - watchdog -
[ 57.442018] procd: - ubus -
[ 57.540750] procd: - init -
Please press Enter to activate this console.
[ 57.872120] kmodloader: loading kernel modules from /etc/modules.d/*
[ 57.891968] urngd: v1.0.2 started.
[ 57.950657] RPC: Registered named UNIX socket transport module.
[ 57.956601] RPC: Registered udp transport module.
[ 57.961341] RPC: Registered tcp transport module.
[ 57.966059] RPC: Registered tcp NFSv4.1 backchannel transport module.
[ 57.981717] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver
[ 57.992186] gre: GRE over IPv4 demultiplexor driver
[ 57.998436] ip_gre: GRE over IPv4 tunneling driver
[ 58.019659] ip6_tables: (C) 2000-2006 Netfilter Core Team
[ 58.036020] nf_conntrack version 0.5.0 (8192 buckets, 32768 max)
[ 58.070726] Netfilter messages via NETLINK v0.30.
[ 58.078269] ip_set: protocol 6
[ 58.108156] cryptodev: driver 1.10 loaded.
[ 58.122455] hidraw: raw HID events driver (C) Jiri Kosina
[ 58.138056] u32 classifier
[ 58.140792] input device check on
[ 58.144480] Actions configured
[ 58.150205] Mirror/redirect action on
[ 58.162874] fuse init (API version 7.26)
[ 58.174430] Loading modules backported from Linux version v4.19.98-0-gd183c8e2647a
[ 58.182137] Backport generated by backports.git v4.19.98-1-0-g8204eb99
[ 58.192910] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 58.240068] ctnetlink v0.93: registering with nfnetlink.
[ 58.306822] usbcore: registered new interface driver ums-alauda
[ 58.315163] usbcore: registered new interface driver ums-cypress
[ 58.327872] usbcore: registered new interface driver ums-datafab
[ 58.335766] usbcore: registered new interface driver ums-freecom
[ 58.343727] usbcore: registered new interface driver ums-isd200
[ 58.352347] usbcore: registered new interface driver ums-jumpshot
[ 58.360553] usbcore: registered new interface driver ums-karma
[ 58.369042] usbcore: registered new interface driver ums-sddr09
[ 58.377233] usbcore: registered new interface driver ums-sddr55
[ 58.385605] usbcore: registered new interface driver ums-usbat
[ 58.396830] usbcore: registered new interface driver usbhid
[ 58.402437] usbhid: USB HID core driver
[ 58.409250] usbcore: registered new interface driver usblp
[ 58.452988] xt_time: kernel timezone is -0000
[ 58.492679] PPP generic driver version 2.4.2
[ 58.498362] PPP MPPE Compression module registered
[ 58.504702] NET: Registered protocol family 24
[ 58.516803] usbcore: registered new interface driver brcmfmac
[ 58.522845] pci_generic_config_write32: 624 callbacks suppressed
[ 58.522862] pci_bus 0000:03: 1-byte config write to 0000:03:00.0 offset 0x3c may corrupt adjacent RW1C bits
[ 58.538731] pci 0000:00:00.0: enabling device (0140 -> 0142)
[ 58.544433] pci_bus 0000:00: 2-byte config write to 0000:00:00.0 offset 0x4 may corrupt adjacent RW1C bits
[ 58.554190] pci_bus 0000:00: 2-byte config write to 0000:00:00.0 offset 0x4 may corrupt adjacent RW1C bits
[ 58.563938] pci 0000:01:00.0: enabling device (0140 -> 0142)
[ 58.569667] pci_bus 0000:01: 2-byte config write to 0000:01:00.0 offset 0x4 may corrupt adjacent RW1C bits
[ 58.579412] pci_bus 0000:01: 2-byte config write to 0000:01:00.0 offset 0x4 may corrupt adjacent RW1C bits
[ 58.589161] pci 0000:02:01.0: enabling device (0140 -> 0142)
[ 58.594873] pci_bus 0000:02: 2-byte config write to 0000:02:01.0 offset 0x4 may corrupt adjacent RW1C bits
[ 58.604624] pci_bus 0000:02: 2-byte config write to 0000:02:01.0 offset 0x4 may corrupt adjacent RW1C bits
[ 58.614389] brcmfmac 0000:03:00.0: enabling device (0140 -> 0142)
[ 58.620562] pci_bus 0000:03: 2-byte config write to 0000:03:00.0 offset 0x4 may corrupt adjacent RW1C bits
[ 58.630323] pci_bus 0000:03: 2-byte config write to 0000:03:00.0 offset 0x4 may corrupt adjacent RW1C bits
[ 58.795610] brcmfmac: brcmf_fw_alloc_request: using brcm/brcmfmac43602-pcie for chip BCM43602/1
[ 58.995125] brcmfmac 0000:03:00.0: Direct firmware load for brcm/brcmfmac43602-pcie.dlink,dir-890l.txt failed with error -2
[ 59.006484] brcmfmac 0000:03:00.0: Direct firmware load for brcm/brcmfmac43602-pcie.txt failed with error -2
[ 59.210743] brcmfmac: brcmf_fw_alloc_request: using brcm/brcmfmac43602-pcie for chip BCM43602/1
[ 59.219622] brcmfmac 0000:03:00.0: Direct firmware load for brcm/brcmfmac43602-pcie.clm_blob failed with error -2
[ 59.229929] brcmfmac: brcmf_c_process_clm_blob: no clm_blob available (err=-2), device may have limited channels available
[ 59.243645] brcmfmac: brcmf_c_preinit_dcmds: Firmware: BCM43602/1 wl0: Sep 18 2015 03:30:01 version 7.35.177.56 (r587209) FWID 01-6cb8e269
[ 59.280512] pci_bus 0000:04: 1-byte config write to 0000:04:00.0 offset 0x3c may corrupt adjacent RW1C bits
[ 59.290371] pci 0000:02:02.0: enabling device (0140 -> 0142)
[ 59.296082] brcmfmac 0000:04:00.0: enabling device (0140 -> 0142)
[ 59.455812] brcmfmac: brcmf_fw_alloc_request: using brcm/brcmfmac43602-pcie for chip BCM43602/1
[ 59.466396] brcmfmac 0000:04:00.0: Direct firmware load for brcm/brcmfmac43602-pcie.dlink,dir-890l.txt failed with error -2
[ 59.477652] brcmfmac 0000:04:00.0: Direct firmware load for brcm/brcmfmac43602-pcie.txt failed with error -2
[ 59.713262] brcmfmac: brcmf_fw_alloc_request: using brcm/brcmfmac43602-pcie for chip BCM43602/1
[ 59.722090] brcmfmac 0000:04:00.0: Direct firmware load for brcm/brcmfmac43602-pcie.clm_blob failed with error -2
[ 59.732399] brcmfmac: brcmf_c_process_clm_blob: no clm_blob available (err=-2), device may have limited channels available
[ 59.745429] brcmfmac: brcmf_c_preinit_dcmds: Firmware: BCM43602/1 wl0: Sep 18 2015 03:30:01 version 7.35.177.56 (r587209) FWID 01-6cb8e269
[ 59.780284] pci 0001:00:00.0: enabling device (0140 -> 0142)
[ 59.786103] brcmfmac 0001:01:00.0: enabling device (0140 -> 0142)
[ 59.945580] brcmfmac: brcmf_fw_alloc_request: using brcm/brcmfmac43602-pcie for chip BCM43602/1
[ 59.956046] brcmfmac 0001:01:00.0: Direct firmware load for brcm/brcmfmac43602-pcie.dlink,dir-890l.txt failed with error -2
[ 59.967297] brcmfmac 0001:01:00.0: Direct firmware load for brcm/brcmfmac43602-pcie.txt failed with error -2
[ 60.159644] brcmfmac: brcmf_fw_alloc_request: using brcm/brcmfmac43602-pcie for chip BCM43602/1
[ 60.168492] brcmfmac 0001:01:00.0: Direct firmware load for brcm/brcmfmac43602-pcie.clm_blob failed with error -2
[ 60.178806] brcmfmac: brcmf_c_process_clm_blob: no clm_blob available (err=-2), device may have limited channels available
[ 60.190825] brcmfmac: brcmf_c_preinit_dcmds: Firmware: BCM43602/1 wl0: Sep 18 2015 03:30:01 version 7.35.177.56 (r587209) FWID 01-6cb8e269
[ 60.229496] kmodloader: done loading kernel modules from /etc/modules.d/*
[ 125.151903] xt_FULLCONENAT: RFC3489 Full Cone NAT module
[ 125.151903] xt_FULLCONENAT: Copyright (C) 2018 Chion Tang <tech@chionlab.moe>
[ 127.036639] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 127.043410] bgmac_bcma bcma0:3 eth0: Link is Up - 1Gbps/Full - flow control off
[ 127.055677] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[ 127.072544] br-lan: port 1(eth0.1) entered blocking state
[ 127.078027] br-lan: port 1(eth0.1) entered disabled state
[ 127.083687] device eth0.1 entered promiscuous mode
[ 127.088530] device eth0 entered promiscuous mode
[ 127.101864] br-lan: port 1(eth0.1) entered blocking state
[ 127.107331] br-lan: port 1(eth0.1) entered forwarding state
[ 127.113055] IPv6: ADDRCONF(NETDEV_UP): br-lan: link is not ready
[ 128.065765] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready
[ 128.602895] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 128.641861] IPv6: ADDRCONF(NETDEV_UP): wlan2: link is not ready
[ 128.654780] br-lan: port 2(wlan0) entered blocking state
[ 128.660182] br-lan: port 2(wlan0) entered disabled state
[ 128.665778] device wlan0 entered promiscuous mode
[ 128.670649] br-lan: port 2(wlan0) entered blocking state
[ 128.676022] br-lan: port 2(wlan0) entered forwarding state
[ 128.710554] IPv6: ADDRCONF(NETDEV_UP): wlan1: link is not ready
[ 128.716701] br-lan: port 3(wlan2) entered blocking state
[ 128.722036] br-lan: port 3(wlan2) entered disabled state
[ 128.727623] device wlan2 entered promiscuous mode
[ 128.732467] br-lan: port 3(wlan2) entered blocking state
[ 128.737833] br-lan: port 3(wlan2) entered forwarding state
[ 128.752024] br-lan: port 4(wlan1) entered blocking state
[ 128.757407] br-lan: port 4(wlan1) entered disabled state
[ 128.763017] device wlan1 entered promiscuous mode
[ 128.767938] br-lan: port 4(wlan1) entered blocking state
[ 128.773270] br-lan: port 4(wlan1) entered forwarding state
[ 128.917340] IPv6: ADDRCONF(NETDEV_CHANGE): wlan1: link becomes ready
[ 129.071215] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
[ 129.083198] br-lan: port 3(wlan2) entered disabled state
[ 129.175602] IPv6: ADDRCONF(NETDEV_CHANGE): wlan2: link becomes ready
[ 129.182153] br-lan: port 3(wlan2) entered blocking state
[ 129.187546] br-lan: port 3(wlan2) entered forwarding state
|
|
简体中文
繁體中文
English
日本語
Deutsch
한국 사람
بالعربية
TÜRKÇE
português
คนไทย
IP卡
狗仔卡
发表于 2020-2-14 13:46
置顶卡
沉默卡
喧嚣卡
顶贴卡
显身卡
