大神来看一下我这个路由器信息

anan***

首先路由器升级固件出现问题，然后ttl线连上了路由器，想刷breed，可是通电后选不了9或2（刚开始按没任何效果，试了好多次），想让大佬看一下通电后屏幕出现的信息:

1. 
   
2. U-Boot 1.1.3 (Feb  2 2015 - 15:31:41)
   
3. 
   
4. Board: Ralink APSoC DRAM:  128 MB
   
5. relocate_code Pointer at: 87fb8000
   
6. enable ephy clock...done. rf reg 29 = 5
   
7. SSC disabled.
   
8. reg = 0xc0030000
   
9. reg = 0xc0030000
   
10. spi_wait_nsec: 29
    
11. spi device id: c2 20 18 c2 20 (2018c220)
    
12. find flash: MX25L12805D
    
13. raspi_read: from:30000 len:1000
    
14. raspi_read: from:30000 len:1000
    
15. ============================================
    
16. Wiwide UBoot Version: 1.0.3
    
17. --------------------------------------------
    
18. ASIC 7620_MP (Port5<->None)
    
19. DRAM component: 1024 Mbits DDR, width 16
    
20. DRAM bus: 16 bit
    
21. Total memory: 128 MBytes
    
22. Flash component: 16 MBytes NOR Flash
    
23. Date:Feb  2 2015  Time:15:31:41
    
24. ============================================
    
25. icache: sets:512, ways:4, linesz:32 ,total:65536
    
26. dcache: sets:256, ways:4, linesz:32 ,total:32768
    
27. 
    
28. ##### The CPU freq = 580 MHZ ####
    
29. estimate memory size =128 Mbytes
    
30. raspi_read: from:50000 len:40
    
31. raspi_read: from:850000 len:40
    
32. 
    
33. =================================================
    
34. Check image validation:
    
35. Image1 Header Magic Number --> OK
    
36. Image2 Header Magic Number --> Failed
    
37. Image1 Header Checksum --> OK
    
38. Image1 Data Checksum --> raspi_read: from:50040 len:160143
    
39. OK
    
40. Image1 Stable Flag --> Not stable
    
41. Image1 Try Counter --> 58
    
42. 
    
43. Image1 is not stable and try counter > 3. Take it as a broken image.
    
44. Image1: Broken Image2: Broken
    
45. Upgrade Mode~~
    
46. 
    
47. =================================================
    
48. raspi_read: from:40028 len:6
    
49. 
    
50. 
    
51. Please choose the operation:
    
52.    1: Load system code to SDRAM via TFTP.
    
53.    2: Load system code then write to Flash via TFTP.
    
54.    3: Boot system code via Flash (default).
    
55.    4: Entr boot command line interface.
    
56.    7: Load Boot Loader code then write to Flash via Serial.
    
57.    9: Load Boot Loader code then write to Flash via TFTP.
    
58. 
    
59.    
    
60. 3: System Boot system code via Flash.
    
61. ## Booting image at bc050000 ...
    
62. raspi_read: from:30000 len:10000
    
63. Erasing SPI Flash...
    
64. raspi_erase: offs:30000 len:10000
    
65. .
    
66. Writing to SPI Flash...
    
67. raspi_write: to:30000 len:10000
    
68. .
    
69. done
    
70. raspi_read: from:50000 len:40
    
71.    Image Name:   MIPS OpenWrt Linux-4.14.151
    
72.    Image Type:   MIPS Linux Kernel Image (lzma compressed)
    
73.    Data Size:    1442115 Bytes =  1.4 MB
    
74.    Load Address: 80000000
    
75.    Entry Point:  80000000
    
76. raspi_read: from:50040 len:160143
    
77.    Verifying Checksum ... OK
    
78.    Uncompressing Kernel Image ... OK
    
79. No initrd
    
80. ## Transferring control to Linux (at address 80000000) ...
    
81. ## Giving linux memsize in MB, 128
    
82. 
    
83. Starting kernel ...
    
84. 
    
85. [    0.000000] Linux version 4.14.151 (buildbot@a6cb27977ad2) (gcc version 7.3.0 (OpenWrt GCC 7.3.0 r7897-9d401013fc)) #0 Tue Nov 5 14:12:18 2019
    
86. [    0.000000] Board has DDR2
    
87. [    0.000000] Analog PMU set to hw control
    
88. [    0.000000] Digital PMU set to hw control
    
89. [    0.000000] SoC Type: MediaTek MT7620A ver:2 eco:6
    
90. [    0.000000] bootconsole [early0] enabled
    
91. [    0.000000] CPU0 revision is: 00019650 (MIPS 24KEc)
    
92. [    0.000000] MIPS: machine is Lenovo Y1
    
93. [    0.000000] Determined physical RAM map:
    
94. [    0.000000]  memory: 08000000 [url=home.php?mod=space&uid=162986]@[/url] 00000000 (usable)
    
95. [    0.000000] Initrd not found or empty - disabling initrd
    
96. [    0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
    
97. [    0.000000] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
    
98. [    0.000000] Zone ranges:
    
99. [    0.000000]   Normal   [mem 0x0000000000000000-0x0000000007ffffff]
    
100. [    0.000000] Movable zone start for each node
     
101. [    0.000000] Early memory node ranges
     
102. [    0.000000]   node   0: [mem 0x0000000000000000-0x0000000007ffffff]
     
103. [    0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x0000000007ffffff]
     
104. [    0.000000] random: get_random_bytes called from 0x80428730 with crng_init=0
     
105. [    0.000000] Built 1 zonelists, mobility grouping on.  Total pages: 32512
     
106. [    0.000000] Kernel command line: console=ttyS0,115200 rootfstype=squashfs,jffs2
     
107. [    0.000000] PID hash table entries: 512 (order: -1, 2048 bytes)
     
108. [    0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
     
109. [    0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
     
110. [    0.000000] Writing ErrCtl register=0006d567
     
111. [    0.000000] Readback ErrCtl register=0006d567
     
112. [    0.000000] Memory: 125192K/131072K available (3601K kernel code, 183K rwdata, 464K rodata, 160K init, 214K bss, 5880K reserved, 0K cma-reserved)
     
113. [    0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
     
114. [    0.000000] NR_IRQS: 256
     
115. [    0.000000] CPU Clock: 580MHz
     
116. [    0.000000] clocksource: systick: mask: 0xffff max_cycles: 0xffff, max_idle_ns: 583261500 ns
     
117. [    0.000000] systick: enable autosleep mode
     
118. [    0.000000] systick: running - mult: 214748, shift: 32
     
119. [    0.000000] clocksource: MIPS: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 6590553264 ns
     
120. [    0.000012] sched_clock: 32 bits at 290MHz, resolution 3ns, wraps every 7405115902ns
     
121. [    0.007594] Calibrating delay loop... 385.84 BogoMIPS (lpj=1929216)
     
122. [    0.073541] pid_max: default: 32768 minimum: 301
     
123. [    0.078276] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
     
124. [    0.084653] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
     
125. [    0.097673] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
     
126. [    0.107218] futex hash table entries: 256 (order: -1, 3072 bytes)
     
127. [    0.113203] pinctrl core: initialized pinctrl subsystem
     
128. [    0.119594] NET: Registered protocol family 16
     
129. [    0.604158] PCI host bridge /pcie@10140000 ranges:
     
130. [    0.608772]  MEM 0x0000000020000000..0x000000002fffffff
     
131. [    0.613824]   IO 0x0000000010160000..0x000000001016ffff
     
132. [    0.636603] rt2880_gpio 10000600.gpio: registering 24 gpios
     
133. [    0.642057] rt2880_gpio 10000600.gpio: registering 24 irq handlers
     
134. [    0.648387] rt2880_gpio 10000660.gpio: registering 32 gpios
     
135. [    0.653808] rt2880_gpio 10000660.gpio: registering 32 irq handlers
     
136. [    0.660092] rt2880_gpio 10000688.gpio: registering 1 gpios
     
137. [    0.665420] rt2880_gpio 10000688.gpio: registering 1 irq handlers
     
138. [    0.672166] PCI host bridge to bus 0000:00
     
139. [    0.676138] pci_bus 0000:00: root bus resource [mem 0x20000000-0x2fffffff]
     
140. [    0.682755] pci_bus 0000:00: root bus resource [io  0xffffffff]
     
141. [    0.688517] pci_bus 0000:00: root bus resource [??? 0x00000000 flags 0x0]
     
142. [    0.695099] pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff]
     
143. [    0.703283] pci 0000:00:00.0: bridge configuration invalid ([bus 00-00]), reconfiguring
     
144. [    0.711744] pci 0000:00:00.0: BAR 0: no space for [mem size 0x80000000]
     
145. [    0.718156] pci 0000:00:00.0: BAR 0: failed to assign [mem size 0x80000000]
     
146. [    0.724872] pci 0000:00:00.0: BAR 8: assigned [mem 0x20000000-0x200fffff]
     
147. [    0.731479] pci 0000:00:00.0: BAR 9: assigned [mem 0x20100000-0x201fffff pref]
     
148. [    0.738479] pci 0000:00:00.0: BAR 1: assigned [mem 0x20200000-0x2020ffff]
     
149. [    0.745097] pci 0000:01:00.0: BAR 0: assigned [mem 0x20000000-0x200fffff 64bit]
     
150. [    0.752190] pci 0000:01:00.0: BAR 6: assigned [mem 0x20100000-0x2010ffff pref]
     
151. [    0.759198] pci 0000:00:00.0: PCI bridge to [bus 01]
     
152. [    0.764009] pci 0000:00:00.0:   bridge window [mem 0x20000000-0x200fffff]
     
153. [    0.770612] pci 0000:00:00.0:   bridge window [mem 0x20100000-0x201fffff pref]
     
154. [    0.782553] clocksource: Switched to clocksource systick
     
155. [    0.788842] NET: Registered protocol family 2
     
156. [    0.794094] TCP established hash table entries: 1024 (order: 0, 4096 bytes)
     
157. [    0.800819] TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
     
158. [    0.807045] TCP: Hash tables configured (established 1024 bind 1024)
     
159. [    0.813310] UDP hash table entries: 256 (order: 0, 4096 bytes)
     
160. [    0.818933] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
     
161. [    0.825313] NET: Registered protocol family 1
     
162. [    0.832270] rt-timer 10000100.timer: maximum frequency is 1220Hz
     
163. [    0.838988] Crashlog allocated RAM at address 0x3f00000
     
164. [    0.845810] workingset: timestamp_bits=30 max_order=15 bucket_order=0
     
165. [    0.858073] squashfs: version 4.0 (2009/01/31) Phillip Lougher
     
166. [    0.863717] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
     
167. [    0.883594] io scheduler noop registered
     
168. [    0.887342] io scheduler deadline registered (default)
     
169. [    0.893368] Serial: 8250/16550 driver, 16 ports, IRQ sharing enabled
     
170. [    0.902461] console [ttyS0] disabled
     
171. [    0.905971] 10000c00.uartlite: ttyS0 at MMIO 0x10000c00 (irq = 20, base_baud = 2500000) is a Palmchip BK-3103
     
172. [    0.915581] console [ttyS0] enabled
     
173. [    0.915581] console [ttyS0] enabled
     
174. [    0.922636] bootconsole [early0] disabled
     
175. [    0.922636] bootconsole [early0] disabled
     
176. [    0.938839] spi spi0.0: force spi mode3
     
177. [    0.943621] m25p80 spi0.0: mx25l12805d (16384 Kbytes)
     
178. [    0.948831] 4 fixed-partitions partitions found on MTD device spi0.0
     
179. [    0.955369] Creating 4 MTD partitions on "spi0.0":
     
180. [    0.960282] 0x000000000000-0x000000030000 : "u-boot"
     
181. [    0.966281] 0x000000030000-0x000000040000 : "u-boot-env"
     
182. [    0.972533] 0x000000040000-0x000000050000 : "factory"
     
183. [    0.978629] 0x000000050000-0x000001000000 : "firmware"
     
184. [    1.104681] 2 uimage-fw partitions found on MTD device firmware
     
185. [    1.110757] 0x000000050000-0x0000001b0183 : "kernel"
     
186. [    1.116743] 0x0000001b0183-0x000001000000 : "rootfs"
     
187. [    1.122680] mtd: device 5 (rootfs) set to be root filesystem
     
188. [    1.130030] 1 squashfs-split partitions found on MTD device rootfs
     
189. [    1.136424] 0x000000400000-0x000001000000 : "rootfs_data"
     
190. [    1.143642] libphy: Fixed MDIO Bus: probed
     
191. [    1.151295] gsw: setting port4 to ephy mode
     
192. [    1.157460] mtk_soc_eth 10100000.ethernet: loaded mt7620 driver
     
193. [    1.164271] mtk_soc_eth 10100000.ethernet eth0: mediatek frame engine at 0xb0100000, irq 5
     
194. [    1.173257] rt2880_wdt 10000120.watchdog: Initialized
     
195. [    1.179787] NET: Registered protocol family 10
     
196. [    1.188511] Segment Routing with IPv6
     
197. [    1.192376] NET: Registered protocol family 17
     
198. [    1.197054] bridge: filtering via arp/ip/ip6tables is no longer available by default. Update your scripts to load br_netfilter if you need this.
     
199. [    1.210291] 8021q: 802.1Q VLAN Support v1.8
     
200. [    1.230397] VFS: Mounted root (squashfs filesystem) readonly on device 31:5.
     
201. [    1.238540] Freeing unused kernel memory: 160K
     
202. [    1.243110] This architecture does not have kernel memory protection.
     
203. [    2.692562] random: fast init done
     
204. [    2.767523] init: Console is alive
     
205. [    2.771237] init: - watchdog -
     
206. [    4.362202] kmodloader: loading kernel modules from /etc/modules-boot.d/*
     
207. [    4.679049] kmodloader: done loading kernel modules from /etc/modules-boot.d/*
     
208. [    4.690558] init: - preinit -
     
209. [    6.401347] 8021q: adding VLAN 0 to HW filter on device eth0
     
210. Press the [f] key and hit [enter] to enter failsafe mode
     
211. Press the [1], [2], [3] or [4] key and hit [enter] to select the debug level
     
212. [    6.556291] random: procd: uninitialized urandom read (4 bytes read)
     
213. [    8.052420] jffs2: notice: (368) jffs2_build_xattr_subsystem: complete building xattr subsystem, 43 of xdatum (3 unchecked, 40 orphan) and 50 of xref (40 dead, 0 orphan) found.
     
214. [    8.071177] mount_root: switching to jffs2 overlay
     
215. [    8.110482] overlayfs: upper fs does not support tmpfile.
     
216. [    8.128732] urandom-seed: Seeding with /etc/urandom.seed
     
217. [    8.414323] procd: - early -
     
218. [    8.417386] procd: - watchdog -
     
219. [    8.752059] procd: - watchdog -
     
220. [    8.755658] procd: - ubus -
     
221. [    8.986073] random: ubusd: uninitialized urandom read (4 bytes read)
     
222. [    8.998291] random: ubusd: uninitialized urandom read (4 bytes read)
     
223. [    9.005423] random: ubusd: uninitialized urandom read (4 bytes read)
     
224. [    9.012972] procd: - init -
     
225. Please press Enter to activate this console.
     
226. [    9.641819] kmodloader: loading kernel modules from /etc/modules.d/*
     
227. [    9.654553] ip6_tables: (C) 2000-2006 Netfilter Core Team
     
228. [    9.672391] Loading modules backported from Linux version wt-2017-11-01-0-gfe248fc2c180
     
229. [    9.680644] Backport generated by backports.git v4.14-rc2-1-31-g86cf0e5d
     
230. [    9.691719] ip_tables: (C) 2000-2006 Netfilter Core Team
     
231. [    9.706369] nf_conntrack version 0.5.0 (2048 buckets, 8192 max)
     
232. [    9.777665] xt_time: kernel timezone is -0000
     
233. [    9.855088] mt76x2e 0000:01:00.0: card - bus=0x1, slot = 0x0 irq=4
     
234. [    9.861597] mt76x2e 0000:01:00.0: ASIC revision: 76120044
     
235. [   10.087650] mt76x2e 0000:01:00.0: ROM patch build: 20141115060606a
     
236. [   10.099702] mt76x2e 0000:01:00.0: Firmware Version: 0.0.00
     
237. [   10.105369] mt76x2e 0000:01:00.0: Build: 1
     
238. [   10.109550] mt76x2e 0000:01:00.0: Build Time: 201507311614____
     
239. [   10.124371] mt76x2e 0000:01:00.0: Firmware running!
     
240. [   10.214846] PPP generic driver version 2.4.2
     
241. [   10.222120] NET: Registered protocol family 24
     
242. [   10.256710] rt2800_wmac 10180000.wmac: loaded eeprom from mtd device "factory"
     
243. [   10.264104] ieee80211 phy1: rt2x00_set_rt: Info - RT chipset 6352, rev 0500 detected
     
244. [   10.272094] ieee80211 phy1: rt2x00_set_rf: Info - RF chipset 7620 detected
     
245. [   10.294702] kmodloader: done loading kernel modules from /etc/modules.d/*
     
246. [   12.056563] urandom_read: 5 callbacks suppressed
     
247. [   12.056575] random: jshn: uninitialized urandom read (4 bytes read)
     
248. [   22.385962] 8021q: adding VLAN 0 to HW filter on device eth0
     
249. [   22.409227] br-lan: port 1(eth0.1) entered blocking state
     
250. [   22.415010] br-lan: port 1(eth0.1) entered disabled state
     
251. [   22.420891] device eth0.1 entered promiscuous mode
     
252. [   22.425842] device eth0 entered promiscuous mode
     
253. [   22.446676] br-lan: port 1(eth0.1) entered blocking state
     
254. [   22.452205] br-lan: port 1(eth0.1) entered forwarding state
     
255. [   22.458181] IPv6: ADDRCONF(NETDEV_UP): br-lan: link is not ready
     
256. [   23.434795] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready
     
257. reboot
     
258. Failed to executPlease press Enter to activate this console.
     
259. [   58.205735] random: crng init done

复制代码

请大佬指点

anan***

无法中断启动，按ctrl c也没反应

afe***

7620A+16M+128M的配置，没法中断就只能编程器了

anan***

afeng11 发表于 2020-2-25 10:37
7620A+16M+128M的配置，没法中断就只能编程器了

那ttl没法用了呀

anan***

afeng11 发表于 2020-2-25 10:37
7620A+16M+128M的配置，没法中断就只能编程器了

路由器上自带的就有ttl排针，那他焊上去的目的要干嘛呀，请大佬指点

afe***

anandyuan 发表于 2020-2-25 13:34
路由器上自带的就有ttl排针，那他焊上去的目的要干嘛呀，请大佬指点

用来调试的，问题不知道中断命令，或者厂家uboot屏蔽了中断命令

anan***

afeng11 发表于 2020-2-25 13:39
用来调试的，问题不知道中断命令，或者厂家uboot屏蔽了中断命令

大佬我按f和回车进入一个界面，您看一下https://s2.ax1x.com/2020/02/25/3YassS.png

afe***

anandyuan 发表于 2020-2-25 15:30
大佬我按f和回车进入一个界面，您看一下https://s2.ax1x.com/2020/02/25/3YassS.png

这个是内嵌的ssh环境，这里用命令也可以写闪存的

anan***

afeng11 发表于 2020-2-25 15:32
这个是内嵌的ssh环境，这里用命令也可以写闪存的

请大佬指点一下用什么命令

afe***

多百度一下，mtd write

fyi***

哪个路由器？？

anan***

fyi2000 发表于 2020-2-27 18:00
哪个路由器？？

迈外迪路由器，论坛有教程，我就是按着教程来的

fyi***

你用的哪个TTL线？
有没有编程器？
PuTTY登陆Openwrt，运行

1. mtd unlock u-boot
   
2. mtd unlock u-boot-env
   
3. mtd unlock firmware
   
4. nvram show

复制代码

把结果贴上来

fyi***

Windows系统如何修改按住键盘按键时字符重复的响应时间及速度 - 小声推
Windows运行 "control keyboard"
"重复延迟" 最短，"重复速度" 最快

接好TTL线
运行PuTTY，开启串口视窗，先按下 "9" 不放，路由器上电，能否中断？
如果TTL线芯片是CH34X，波特率设置117000，8n1
刷好Breed，先备份固件再刷机

迈外迪 w1211 路由器刷tomato不死鸟成功！附教程 - Tomato Phoenix不死鸟 - 无线论坛
Breed和固件选联想Y1(=Newifi mini)
https://breed.hackpascal.net/
hanwckf版老毛子 (下载百度盘)
精工细作的 Padavan 固件（K2P、Newifi3、Newifi-Mini、小娱C1/C5支持SATA啦）
hiboy版老毛子 (扩展插件最多)

anan***

fyi2000 发表于 2020-2-27 19:38
Windows系统如何修改按住键盘按键时字符重复的响应时间及速度 - 小声推
Windows运行 "control keyboard"
...

首先多谢大佬的帮忙，可能我这个不行，按9只在他启动7秒后才会显示9，我录屏看了，提示让选择立马就出现3这个默认选项，一直按着也不行，那我只好放弃用ttl了，昨晚在淘宝上下单了编程器，准备用编程器刷，想问下大佬所谓的编程器固件跟用ttl刷的固件可以是同一个文件吗是不是有区别呀，那breed呢，感谢大佬，看到请回复一下