找回密码
 立即注册

QQ登录

只需一步,快速开始

搜索
广告投放联系QQ68610888
查看: 4357|回复: 15

[k2p] K2P改USB变砖后的诡异现象

[复制链接]
发表于 2018-4-24 18:18 | 显示全部楼层 |阅读模式
[ 本帖最后由 ht61929765 于 2018-4-24 19:42 编辑 ]\n\n[ 本帖最后由 ht61929765 于 2018-4-24 18:32 编辑 ]\n\n手里两台K2P A1  之前改了一台不过USB3开启3.0模式就不认盘了,2.0正常。。。搞了几回都不行,最近得空把另一台拿出来,打好孔后就开始焊线,先是2.0。。万用表量了下一切正常就插U盘了。。可是一直不识别,换了三次线 D+ D- 也对调了几下,都不识别,于是弄了一个作死的行为。。开着机用万用表测D+ D-的对地电压。。都是2.X伏 刚测完,电脑本地连接没了,一摸MT7621 巨烫无比。。立马拔电。心想这回完了。再加电试一下,比热得快热的还快。。。测了下  TP12 跟GND是短路状态了。。于是淘宝看MT7621AT36-40元。。死马当活马医,吹下来搞搞,不行就买一个U了,吹下来后 测了下,没短路。也可能是引脚搞错了  记不得了,没钢网,懒得摆锡球,看了下板上残锡多就把U清理了下,又吹上去了,加电后 闪了一下蓝灯,立马觉得有戏,进breed。。无碍,于是又搞起USB了。。。。忽略了进系统这一环节,后面发现,现在只能进breed或者原厂U-boot之类的bootloader了。。。加上TTL看输出。。一直卡在如下环节。。。USB部分还是挂了。。。。TTL输出如下
===================================================================
                MT7621   stage1 code 10:33:55 (ASIC)
                CPU=500000000 HZ BUS=166666666 HZ
==================================================================
Change MPLL source from XTAL to CR...
do MEMPLL setting..
MEMPLL Config : 0x11100000
3PLL mode + External loopback
=== XTAL-40Mhz === DDR-1200Mhz ===
PLL2 FB_DL: 0x10, 1/0 = 668/356 41000000
PLL4 FB_DL: 0x12, 1/0 = 746/278 49000000
PLL3 FB_DL: 0x19, 1/0 = 656/368 65000000
do DDR setting..[01F40000]
Apply DDR3 Setting...(use customer AC)
          0    8   16   24   32   40   48   56   64   72   80   88   96  104  112  120
      --------------------------------------------------------------------------------
0000:|    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0
0001:|    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0
0002:|    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0
0003:|    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0
0004:|    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0
0005:|    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0
0006:|    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0
0007:|    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0
0008:|    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0
0009:|    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0
000A:|    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0
000B:|    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0
000C:|    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0
000D:|    0    0    0    0    0    0    0    0    0    0    0    0    0    0    1    1
000E:|    0    0    0    0    0    0    0    0    1    1    1    1    1    1    1    1
000F:|    0    0    0    1    1    1    1    1    1    1    1    1    1    0    0    0
0010:|    1    1    1    1    1    1    1    1    0    0    0    0    0    0    0    0
0011:|    1    1    1    0    0    0    0    0    0    0    0    0    0    0    0    0
0012:|    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0
0013:|    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0
0014:|    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0
0015:|    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0
0016:|    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0
0017:|    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0
0018:|    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0
0019:|    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0
001A:|    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0
001B:|    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0
001C:|    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0
001D:|    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0
001E:|    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0
001F:|    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0
rank 0 coarse = 15
rank 0 fine = 64
B:|    0    0    0    0    0    0    0    0    1    1    1    0    0    0    0    0
opt_dle value:9
DRAMC_R0DELDLY[018]=00001E1D
==================================================================
                RX      DQS perbit delay software calibration
==================================================================
1.0-15 bit dq delay value
==================================================================
bit|     0  1  2  3  4  5  6  7  8  9
--------------------------------------
0 |    10 6 9 9 7 7 9 7 7 7
10 |    8 10 9 10 7 9
--------------------------------------

==================================================================
2.dqs window
x=pass dqs delay value (min~max)center
y=0-7bit DQ of every group
input delayQS0 =29 DQS1 = 30
==================================================================
bit     DQS0     bit      DQS1
0  (1~57)29  8  (2~58)30
1  (1~55)28  9  (0~56)28
2  (1~57)29  10  (1~58)29
3  (1~58)29  11  (2~59)30
4  (1~57)29  12  (1~60)30
5  (1~58)29  13  (2~57)29
6  (1~56)28  14  (1~59)30
7  (1~58)29  15  (1~59)30
==================================================================
3.dq delay value last
==================================================================
bit|    0  1  2  3  4  5  6  7  8   9
--------------------------------------
0 |    10 7 9 9 7 7 10 7 7 9
10 |    9 10 9 11 7 9
==================================================================
==================================================================
     TX  perbyte calibration
==================================================================
DQS loop = 15, cmp_err_1 = ffff0000
dqs_perbyte_dly.last_dqsdly_pass[0]=15,  finish count=1
dqs_perbyte_dly.last_dqsdly_pass[1]=15,  finish count=2
DQ loop=15, cmp_err_1 = ffff0082
dqs_perbyte_dly.last_dqdly_pass[1]=15,  finish count=1
DQ loop=14, cmp_err_1 = ffff0080
DQ loop=13, cmp_err_1 = ffff0000
dqs_perbyte_dly.last_dqdly_pass[0]=13,  finish count=2
byte:0, (DQS,DQ)=(9,8)
byte:1, (DQS,DQ)=(8,8)
20,data:89
[EMI] DRAMC calibration passed

===================================================================
                MT7621   stage1 code done
                CPU=500000000 HZ BUS=166666666 HZ
===================================================================


U-Boot 1.1.3 ( - )

Board: Ralink APSoC DRAM:  256 MB
uboot gpio init : WPS / RESET pin
relocate_code Pointer at: 8ffa8000

Config XHCI 40M PLL
flash manufacture id: ef, device id 40 18
find flash: W25Q128BV
ra_spi_flash_size:0x1000000
*** Warning - bad CRC, using default environment

default load_addr 0x88000000
============================================
Ralink UBoot Version: 5.0.0.0
--------------------------------------------
ASIC MT7621A DualCore (MAC to MT7530 Mode)
DRAM_CONF_FROM: Auto-Detection
DRAM_TYPE: DDR3
DRAM bus: 16 bit
Xtal Mode=3 OCP Ratio=1/3
Flash component: SPI Flash
Date:  Time:
============================================
icache: sets:256, ways:4, linesz:32 ,total:32768
dcache: sets:256, ways:4, linesz:32 ,total:32768

##### The CPU freq = 880 MHZ ####
estimate memory size =256 Mbytes
#Reset_MT7530
set LAN/WAN LLLLW

Press press hardware button for more than 4 seconds to run web failsafe mode



Catution: hardware button wasn't pressed or not long enough!
Continuing normal boot...


Please choose the operation:
   1: Load system code to SDRAM via TFTP.
   2: Load system code then write to Flash via TFTP.
   3: Boot system code via Flash (default).
   4: Entr boot command line interface.
   6: Load all then write to Flash via TFTP.
   7: Load Boot Loader code then write to Flash via Serial.
   9: Load Boot Loader code then write to Flash via TFTP.
default: 3


3: System Boot system code via Flash.
## Booting image at bc0a0000 ...
   Image Name:   OpenWrt-Linux-3.10.14
   Image Type:   MIPS Linux Kernel Image (lzma compressed)
   Data Size:    3241002 Bytes =  3.1 MB
   Load Address: 81001000
   Entry Point:  81001000
   Verifying Checksum ... OK
   Uncompressing Kernel Image ... OK
No initrd
## Transferring control to Linux (at address 81001000) ...
## Giving linux memsize in MB, 256

Starting kernel ...


LINUX started...

THIS IS ASIC

SDK 5.0.S.0
[    0.000000] Linux version 3.10.14 (jenkins@SOHO-OPWRT) (gcc version 4.8.3 (OpenWrt/Linaro GCC 4.8-2014.04 unknown) ) #1 SMP Thu May 4 18:12:48 CST 2017
[    0.000000]
[    0.000000]  The CPU feqenuce set to 880 MHz
[    0.000000] GCMP present
[    0.000000] CPU0 revision is: 0001992f (MIPS 1004Kc)
[    0.000000] Software DMA cache coherency
[    0.000000] Determined physical RAM map:
[    0.000000]  memory: 08000000 @ 00000000 (usable)
[    0.000000] Initrd not found or empty - disabling initrd
[    0.000000] Zone ranges:
[    0.000000]   DMA      [mem 0x00000000-0x00ffffff]
[    0.000000]   Normal   [mem 0x01000000-0x07ffffff]
[    0.000000] Movable zone start for each node
[    0.000000] Early memory node ranges
[    0.000000]   node   0: [mem 0x00000000-0x07ffffff]
[    0.000000] Detected 3 available secondary CPU(s)
[    0.000000] Primary instruction cache 32kB, 4-way, VIPT, linesize 32 bytes.
[    0.000000] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
[    0.000000] MIPS secondary cache 256kB, 8-way, linesize 32 bytes.
[    0.000000] PERCPU: Embedded 7 pages/cpu @8198e000 s6464 r8192 d14016 u32768
[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 32512
[    0.000000] Kernel command line: console=ttyS1,57600n8 root=/dev/mtdblock6 rootfstype=squashfs,jffs2
[    0.000000] PID hash table entries: 512 (order: -1, 2048 bytes)
[    0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
[    0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
[    0.000000] Writing ErrCtl register=00020b9b
[    0.000000] Readback ErrCtl register=00020b9b
[    0.000000] Memory: 121064k/131072k available (5395k kernel code, 10008k reserved, 2338k data, 260k init, 0k highmem)
[    0.000000] Hierarchical RCU implementation.
[    0.000000] NR_IRQS:128
[    0.000000] console [ttyS1] enabled
[    0.120000] Calibrating delay loop... 577.53 BogoMIPS (lpj=1155072)
[    0.160000] pid_max: default: 32768 minimum: 301
[    0.164000] Mount-cache hash table entries: 512
[    0.168000] launch: starting cpu1
[    0.172000] launch: cpu1 gone!
[    0.172000] CPU1 revision is: 0001992f (MIPS 1004Kc)
[    0.172000] Primary instruction cache 32kB, 4-way, VIPT, linesize 32 bytes.
[    0.172000] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
[    0.172000] MIPS secondary cache 256kB, 8-way, linesize 32 bytes.
[    0.204000] Synchronize counters for CPU 1: done.
[    0.212000] launch: starting cpu2
[    0.216000] launch: cpu2 gone!
[    0.216000] CPU2 revision is: 0001992f (MIPS 1004Kc)
[    0.216000] Primary instruction cache 32kB, 4-way, VIPT, linesize 32 bytes.
[    0.216000] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
[    0.216000] MIPS secondary cache 256kB, 8-way, linesize 32 bytes.
[    0.248000] Synchronize counters for CPU 2: done.
[    0.256000] launch: starting cpu3
[    0.260000] launch: cpu3 gone!
[    0.260000] CPU3 revision is: 0001992f (MIPS 1004Kc)
[    0.260000] Primary instruction cache 32kB, 4-way, VIPT, linesize 32 bytes.
[    0.260000] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
[    0.260000] MIPS secondary cache 256kB, 8-way, linesize 32 bytes.
[    0.288000] Synchronize counters for CPU 3: done.
[    0.296000] Brought up 4 CPUs
[    0.300000] NET: Registered protocol family 16
[    0.600000] release PCIe RST: RALINK_RSTCTRL = 7000000
[    0.604000] PCIE PHY initialize
[    0.608000] ***** Xtal 40MHz *****
[    0.612000] start MT7621 PCIe register access
[    1.204000] RALINK_RSTCTRL = 7000000
[    1.208000] RALINK_CLKCFG1 = 77ffeff8
[    1.212000]
[    1.212000] *************** MT7621 PCIe RC mode *************
[    1.708000] PCIE1 no card, disable it(RST&CLK)
[    1.712000] PCIE2 no card, disable it(RST&CLK)
[    1.716000] pcie_link status = 0x1
[    1.720000] RALINK_RSTCTRL= 1000000
[    1.724000] *** Configure Device number setting of Virtual PCI-PCI bridge ***
[    1.728000] RALINK_PCI_PCICFG_ADDR = 21007f2 -> 21007f2
[    1.732000] PCIE0 enabled
[    1.736000] interrupt enable status: 100000
[    1.740000] Port 0 N_FTS = 1b105000
[    1.744000] config reg done
[    1.748000] init_rt2880pci done
[    1.752000]
[    1.752000]
[    1.752000]  ********** mt7623_audio_init **********
[    1.752000]
[    1.780000] bio: create slab <bio-0> at 0
[    1.784000] SCSI subsystem initialized
[    1.788000] usbcore: registered new interface driver usbfs
[    1.792000] usbcore: registered new interface driver hub
[    1.796000] usbcore: registered new device driver usb
[    1.800000] Advanced Linux Sound Architecture Driver Initialized.
[    1.804000] PCI host bridge to bus 0000:00
[    1.808000] pci_bus 0000:00: root bus resource [mem 0x60000000-0x6fffffff]
[    1.812000] pci_bus 0000:00: root bus resource [io  0x1e160000-0x1e16ffff]
[    1.816000] pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff]
[    1.820000] pci 0000:00:00.0: bridge configuration invalid ([bus 00-00]), reconfiguring
[    1.824000] pci 0000:00:00.0: BAR 0: can't assign mem (size 0x80000000)
[    1.828000] pci 0000:00:00.0: BAR 8: assigned [mem 0x60000000-0x600fffff]
[    1.832000] pci 0000:00:00.0: BAR 1: assigned [mem 0x60100000-0x6010ffff]
[    1.836000] pci 0000:01:00.0: BAR 0: assigned [mem 0x60000000-0x600fffff 64bit]
[    1.840000] pci 0000:00:00.0: PCI bridge to [bus 01]
[    1.844000] pci 0000:00:00.0:   bridge window [mem 0x60000000-0x600fffff]
[    1.848000] PCI: Enabling device 0000:00:00.0 (0004 -> 0006)
[    1.852000] BAR0 at slot 0 = 0
[    1.856000] bus=0x0, slot = 0x0
[    1.860000] res[0]->start = 0
[    1.864000] res[0]->end = 0
[    1.868000] res[1]->start = 60100000
[    1.872000] res[1]->end = 6010ffff
[    1.876000] res[2]->start = 0
[    1.880000] res[2]->end = 0
[    1.884000] res[3]->start = 0
[    1.888000] res[3]->end = 0
[    1.892000] res[4]->start = 0
[    1.896000] res[4]->end = 0
[    1.900000] res[5]->start = 0
[    1.904000] res[5]->end = 0
[    1.908000] bus=0x1, slot = 0x0, irq=0x4
[    1.912000] res[0]->start = 60000000
[    1.916000] res[0]->end = 600fffff
[    1.920000] res[1]->start = 0
[    1.924000] res[1]->end = 0
[    1.928000] res[2]->start = 0
[    1.932000] res[2]->end = 0
[    1.936000] res[3]->start = 0
[    1.940000] res[3]->end = 0
[    1.944000] res[4]->start = 0
[    1.948000] res[4]->end = 0
[    1.952000] res[5]->start = 0
[    1.956000] res[5]->end = 0
[    1.960000] Switching to clocksource MIPS
[    1.964000] NET: Registered protocol family 2
[    1.972000] TCP established hash table entries: 1024 (order: 1, 8192 bytes)
[    1.988000] TCP bind hash table entries: 1024 (order: 1, 8192 bytes)
[    2.000000] TCP: Hash tables configured (established 1024 bind 1024)
[    2.012000] TCP: reno registered
[    2.020000] UDP hash table entries: 256 (order: 1, 8192 bytes)
[    2.032000] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes)
[    2.044000] NET: Registered protocol family 1
[    2.140000] 4 CPUs re-calibrate udelay(lpj = 1167360)
[    2.156000] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[    2.164000] jffs2: version 2.2. (NAND) (SUMMARY)  (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[    2.184000] msgmni has been set to 236
[    2.196000] io scheduler noop registered (default)
[    2.204000] reg_int_mask=0, INT_MASK= 0
[    2.212000] HSDMA_init
[    2.216000]
[    2.216000]  hsdma_phy_tx_ring0 = 0x00c00000, hsdma_tx_ring0 = 0xa0c00000
[    2.236000]
[    2.236000]  hsdma_phy_rx_ring0 = 0x00c04000, hsdma_rx_ring0 = 0xa0c04000
[    2.252000] TX_CTX_IDX0 = 0
[    2.256000] TX_DTX_IDX0 = 0
[    2.260000] RX_CRX_IDX0 = 3ff
[    2.268000] RX_DRX_IDX0 = 0
[    2.272000] set_fe_HSDMA_glo_cfg
[    2.280000] HSDMA_GLO_CFG = 465
[    2.292000] Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled
[    2.304000] serial8250: ttyS0 at MMIO 0x1e000d00 (irq = 27) is a 16550A
[    2.320000] serial8250: ttyS1 at MMIO 0x1e000c00 (irq = 26) is a 16550A
[    2.332000] button_netlink: create netlink socket ok.
[    2.340000] Ralink gpio driver initialized
[    2.352000] Enable Ralink GDMA Controller Module
[    2.360000] GDMA IP Version=3
[    2.364000] ******* i2s module init **********
[    2.376000] flash manufacture id: ef, device id 40 18
[    2.384000] W25Q128BV(ef 40180000) (16384 Kbytes)
[    2.396000] mtd .name = raspi, .size = 0x01000000 (16M) .erasesize = 0x00010000 (64K) .numeraseregions = 0
[    2.416000] Creating 6 MTD partitions on "raspi":
[    2.424000] 0x000000000000-0x000001000000 : "ALL"
[    2.436000] 0x000000000000-0x000000030000 : "Bootloader"
[    2.448000] 0x000000030000-0x000000040000 : "Config"
[    2.456000] 0x000000040000-0x000000050000 : "Factory"
[    2.468000] 0x000000050000-0x0000000a0000 : "permanent_config"
[    2.480000] 0x0000000a0000-0x000001000000 : "firmware"
[    2.492000] 0x0000003b746a-0x000001000000 : "rootfs"
[    2.504000] mtd: partition "rootfs" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only
[    2.528000] mtd: partition "rootfs_data" created automatically, ofs=0xe00000, len=0x200000
[    2.544000] 0x000000e00000-0x000001000000 : "rootfs_data"
[    2.556000] register mt_drv
[    2.572000]
[    2.572000]
[    2.572000] === pAd = c0181000, size = 3628936 ===
[    2.572000]
[    2.592000] <-- RTMPAllocAdapterBlock, Status=0
[    2.600000] get_wdev_by_idx: invalid idx(0)
[    2.608000] pAd->ciHif.CSRBaseAddress =0xc0080000, csr_addr=0xc0080000!
[    2.624000] get_wdev_by_idx: invalid idx(0)
[    2.632000] RTMPInitPCIeDevice():device_id=0x7615
[    2.640000] DriverOwn()::Try to Clear FW Own...
[    2.948000] DriverOwn()::Success to clear FW Own
[    2.956000] mt_pci_chip_cfg(): HWVer=0x8a10, FWVer=0x8a10, pAd->ChipID=0x7615
[    2.972000] mt_pci_chip_cfg(): HIF_SYS_REV=0x76150001
[    2.980000] RtmpChipOpsHook(493): Not support for HIF_MT yet! MACVersion=0x0
[    2.996000] mt7615_init()-->
[    3.000000] Use the default ePAeLNA bin image!
[    3.012000] Use the default /etc/wlan/MT7615E_EEPROM1.bin bin image!
[    3.024000] <--mt7615_init()
[    3.028000] ChipOpsMCUHook
[    3.040000] cut_through_token_list_init(): TokenList inited done!id_head/tail=0/4096
[    3.056000] cut_through_token_list_init(): 8763fb88,8763fb88
[    3.068000] cut_through_token_list_init(): TokenList inited done!id_head/tail=0/4096
[    3.084000] cut_through_token_list_init(): 8763fb98,8763fb98
[    3.096000] <-- RTMPAllocTxRxRingMemory, Status=0
[    3.104000] get_wdev_by_idx: invalid idx(0)
[    3.112000] get_wdev_by_idx: invalid idx(0)
[    3.120000] get_wdev_by_idx: invalid idx(0)
[    3.128000] get_wdev_by_idx: invalid idx(0)
[    3.136000] get_wdev_by_idx: invalid idx(0)
[    3.144000] get_wdev_by_idx: invalid idx(0)
[    3.156000] get_wdev_by_idx: invalid idx(0)
[    3.164000] rdm_major = 253
[    3.168000] GMAC1_MAC_ADRH -- : 0x0000747d
[    3.176000] GMAC1_MAC_ADRL -- : 0x24533c6a
[    3.184000] Ralink APSoC Ethernet Driver Initilization. v3.1  1024 rx/tx descriptors allocated, mtu = 1500!
[    3.204000] GMAC1_MAC_ADRH -- : 0x0000747d
[    3.212000] GMAC1_MAC_ADRL -- : 0x24533c6a
[    3.220000] PROC INIT OK!
[    3.228000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[    3.240000] ehci-pci: EHCI PCI platform driver
[    3.248000] *****run project phy.
[    3.264000] FM_OUT value: u4FmOut = 0(0x00000000)
[    3.280000] FM_OUT value: u4FmOut = 0(0x00000000)
[    3.296000] FM_OUT value: u4FmOut = 0(0x00000000)
[    3.316000] FM_OUT value: u4FmOut = 0(0x00000000)
[    3.336000] FM_OUT value: u4FmOut = 0(0x00000000)
[    3.356000] FM_OUT value: u4FmOut = 0(0x00000000)
[    3.372000] FM_OUT value: u4FmOut = 0(0x00000000)
[    3.392000] FM_OUT value: u4FmOut = 0(0x00000000)
[    3.408000] FM_OUT value: u4FmOut = 0(0x00000000)
[    3.428000] FM_OUT value: u4FmOut = 0(0x00000000)
[    3.460000] FM_OUT value: u4FmOut = 0(0x00000000)
[    3.480000] FM_OUT value: u4FmOut = 0(0x00000000)
[    3.500000] FM_OUT value: u4FmOut = 0(0x00000000)
[    3.520000] FM_OUT value: u4FmOut = 0(0x00000000)
[    3.536000] FM_OUT value: u4FmOut = 0(0x00000000)
[    3.556000] FM_OUT value: u4FmOut = 0(0x00000000)
[    3.572000] FM_OUT value: u4FmOut = 0(0x00000000)
[    3.592000] FM_OUT value: u4FmOut = 0(0x00000000)
[    3.612000] FM_OUT value: u4FmOut = 0(0x00000000)
[    3.632000] FM_OUT value: u4FmOut = 0(0x00000000)
[    3.768000] xhci-hcd xhci-hcd: xHCI Host Controller
[    3.776000] xhci-hcd xhci-hcd: new USB bus registered, assigned bus number 1INFO: rcu_sched detected stalls on CPUs/tasks: { 2} (detected by 0, t=5252 jiffies, g=4294967027, c=429496702

我的恩山、我的无线 The best wifi forum is right here.
发表于 2018-4-24 18:25 | 显示全部楼层
哈,看样子跟我去年2p首发时玩加u口一个毛病,应该也是u挂了!这个7621非常脆弱!!

点评

唉 死而不僵。。耽误事 搞了半天的线  详情 回复 发表于 2018-4-24 18:33
我的恩山、我的无线 The best wifi forum is right here.
回复

使用道具 举报

 楼主| 发表于 2018-4-24 18:33 | 显示全部楼层
qq222g 发表于 2018-4-24 18:25
哈,看样子跟我去年2p首发时玩加u口一个毛病,应该也是u挂了!这个7621非常脆弱!!

唉  死而不僵。。耽误事 搞了半天的线
我的恩山、我的无线 The best wifi forum is right here.
回复

使用道具 举报

发表于 2018-4-24 18:54 来自手机 | 显示全部楼层
改好usb一天后就挂了,连ttl也没输出,某宝淘了个7621换上复活,usb加了tvs管,现已正常使用半年有余
我的恩山、我的无线 The best wifi forum is right here.
回复

使用道具 举报

发表于 2018-4-24 19:54 | 显示全部楼层
哦?这么可怕?
我的恩山、我的无线 The best wifi forum is right here.
回复

使用道具 举报

发表于 2018-4-24 19:55 | 显示全部楼层
因为没需求,所以没加U口动力,第一批两台已使用10个月,稳如狗。
我的恩山、我的无线 The best wifi forum is right here.
回复

使用道具 举报

发表于 2018-4-24 21:09 来自手机 | 显示全部楼层
不想破坏外壳焊了个TF卡座,买路由送的32G卡刚好放进去。这样有你处搞坏了还可以申请售后。
我的恩山、我的无线 The best wifi forum is right here.
回复

使用道具 举报

发表于 2018-4-24 21:27 | 显示全部楼层
ht61929765 发表于 2018-4-24 18:33
唉  死而不僵。。耽误事 搞了半天的线

我搞了2天2夜找不到原因!最后只能贱卖!

点评

多少钱卖的  详情 回复 发表于 2018-4-25 08:55
我的恩山、我的无线 The best wifi forum is right here.
回复

使用道具 举报

发表于 2018-4-24 21:49 | 显示全部楼层
想知道A2有这个问题么
我的恩山、我的无线 The best wifi forum is right here.
回复

使用道具 举报

发表于 2018-4-24 22:06 | 显示全部楼层
测电压当然得开机啊,关机测啥电压?
万用表电压档测D+\D-也不能导致芯片出故障啊,要不手机、电脑主板之类的还怎么修,不让开机测电压,啥都修不了。

点评

是这个道理 可能是我手捏了表笔针。。导致的  详情 回复 发表于 2018-4-25 08:55
我的恩山、我的无线 The best wifi forum is right here.
回复

使用道具 举报

 楼主| 发表于 2018-4-25 08:55 | 显示全部楼层
DEATH 发表于 2018-4-24 22:06
测电压当然得开机啊,关机测啥电压?
万用表电压档测D+\D-也不能导致芯片出故障啊,要不手机、电脑主板之 ...

是这个道理 可能是我手捏了表笔针。。导致的
我的恩山、我的无线 The best wifi forum is right here.
回复

使用道具 举报

 楼主| 发表于 2018-4-25 08:55 | 显示全部楼层
qq222g 发表于 2018-4-24 21:27
我搞了2天2夜找不到原因!最后只能贱卖!

多少钱卖的
我的恩山、我的无线 The best wifi forum is right here.
回复

使用道具 举报

发表于 2018-4-25 09:19 | 显示全部楼层
ht61929765 发表于 2018-4-25 08:55
多少钱卖的

好像是70
我的恩山、我的无线 The best wifi forum is right here.
回复

使用道具 举报

发表于 2018-12-31 01:56 | 显示全部楼层

===================================================================
                MT7621   stage1 code 10:33:55 (ASIC)
                CPU=500000000 HZ BUS=166666666 HZ
==================================================================
Change MPLL source from XTAL to CR...
do MEMPLL setting..
MEMPLL Config : 0x11100000
3PLL mode + External loopback
=== XTAL-40Mhz === DDR-1200Mhz ===
PLL3 FB_DL: 0xe, 1/0 = 645/379 39000000
PLL4 FB_DL: 0x14, 1/0 = 549/475 51000000
PLL2 FB_DL: 0x16, 1/0 = 567/457 59000000
do DDR setting..[01F40000]
Apply DDR3 Setting...(use customer AC)
          0    8   16   24   32   40   48   56   64   72   80   88   96  104  112  120
      --------------------------------------------------------------------------------
0000:|    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0
0001:|    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0
0002:|    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0
0003:|    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0
0004:|    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0
0005:|    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0
0006:|    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0
0007:|    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0
0008:|    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0
0009:|    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0
000A:|    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0
000B:|    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0
000C:|    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0
000D:|    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0
000E:|    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0
000F:|    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0
0010:|    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0
0011:|    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0
0012:|    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0
0013:|    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0
0014:|    0    0    0    0    0    0    0    0    0    0    1    0    0    0    0    0
0015:|    0    0    0    0    0    0    0    0    1    0    0    0    0    0    0    0
0016:|    0    0    0    0    0    0    0    0    0    0    0    0    0    1    0    0
0017:|    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0
0018:|    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0
0019:|    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0
001A:|    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0    1
001B:|    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0
001C:|    0    0    0    1    0    0    0    0    0    0    1    0    0    0    0    0
001D:|    0    0    0    0    0    0    0    0    0    0    1    1    1    0    1    1
001E:|    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0
001F:|    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0
rank 0 coarse = 29
rank 0 fine = 96
B:|    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0
cannot find opt_dle value
[EMI] DRAMC calibration failed
=====================DBG=====================
[000] = 44694683        [004] = f07486a1        [008] = 03046948        [00c] = 0a000000
[010] = 00008888        [014] = 00008888        [018] = 0e0e0e0e        [01c] = 00000000
[020] = 00000000        [024] = 00000000        [028] = f1200f01        [02c] = 55010000
[030] = 33000fff        [034] = 55020000        [038] = 33000fff        [03c] = 55000000
[040] = aa0007ff        [044] = 9f0f0481        [048] = 0000d10d        [04c] = 00000000
[050] = 00000000        [054] = 00000000        [058] = 00000000        [05c] = 00000000
[060] = 00000000        [064] = 00000000        [068] = 00000000        [06c] = 00000000
[070] = 00000000        [074] = 00000000        [078] = 00000000        [07c] = c287227d
[080] = 00000000        [084] = 00000000        [088] = 00000400        [08c] = 00000000
[090] = 00000000        [094] = 60606060        [098] = 00000000        [09c] = 00000000
[0a0] = 00000000        [0a4] = 00000000        [0a8] = 00000000        [0ac] = 00000000
[0b0] = 00000000        [0b4] = 00000000        [0b8] = aa00aa00        [0bc] = aa00aa00
[0c0] = 00000000        [0c4] = 00000000        [0c8] = 00000000        [0cc] = 00000000
[0d0] = 07070000        [0d4] = 00000000        [0d8] = 00300900        [0dc] = 83000000
[0e0] = 17000000        [0e4] = 000022b3        [0e8] = 00000000        [0ec] = 00000000
[0f0] = 00000000        [0f4] = 01000000        [0f8] = edcb000f        [0fc] = 07100000
[100] = 00000000        [104] = 00000000        [108] = 00000000        [10c] = 00000000
[110] = 00051100        [114] = 00000000        [118] = 00000000        [11c] = 00000000
[120] = 00000000        [124] = 80000011        [128] = 00000000        [12c] = 00000000
[130] = 30000000        [134] = 00000000        [138] = 00000000        [13c] = 00000000
[140] = 00000000        [144] = 00000000        [148] = 00000000        [14c] = 00000000
[150] = 00000000        [154] = 00000000        [158] = 00000000        [15c] = 00000000
[160] = 00000000        [164] = 00000000        [168] = 00000080        [16c] = 00000000
[170] = 00000000        [174] = 00000000        [178] = 00000000        [17c] = 00000000
[180] = 00000000        [184] = 00000000        [188] = 00000000        [18c] = 00000000
[190] = 00000000        [194] = 00000000        [198] = 00000000        [19c] = 00000000
[1a0] = 00000000        [1a4] = 00000000        [1a8] = 00000000        [1ac] = 00000000
[1b0] = 00000000        [1b4] = 00000000        [1b8] = 00000000        [1bc] = 00000000
[1c0] = 00000000        [1c4] = 00000000        [1c8] = 00000000        [1cc] = 00000000
[1d0] = 00000000        [1d4] = 00000000        [1d8] = 00c80008        [1dc] = 15602842
[1e0] = 8c000000        [1e4] = 00001000        [1e8] = 00000240        [1ec] = 00000000
[1f0] = 00000000        [1f4] = 00020100        [1f8] = 00000000        [1fc] = 00000000
[200] = 88888888        [204] = 88888888        [208] = 88888888        [20c] = 88888888
[210] = 00000000        [214] = 00000000        [218] = 00000000        [21c] = 00000000
[220] = 00000000        [224] = 00000000        [228] = 00000000        [22c] = 00000000
[230] = 00000000        [234] = 00000000        [238] = 00000000        [23c] = 00000000
[240] = 00000000        [244] = 00000000        [248] = 00000000        [24c] = 00000000
[250] = 00000000        [254] = 00000000        [258] = 00000000        [25c] = 00000000
[260] = 00000000        [264] = 00000000        [268] = 00000000        [26c] = 00000000
[270] = 00000000        [274] = 00000000        [278] = 00000000        [27c] = 00000000
[280] = 0000209b        [284] = 00000000        [288] = 00000355        [28c] = 00001bff
[290] = 00000000        [294] = 00000011        [298] = 00001c00        [29c] = 00000000
[2a0] = 00000010        [2a4] = 00001c00        [2a8] = 0000faa4        [2ac] = 0000054c
[2b0] = 18db35bb        [2b4] = 02406d97        [2b8] = 0005f444        [2bc] = 00000000
[2c0] = 00000000        [2c4] = 00000000        [2c8] = 00000000        [2cc] = 00000000
[2d0] = 00000000        [2d4] = 00000000        [2d8] = 00000000        [2dc] = 00000000
[2e0] = 00000000        [2e4] = 00000000        [2e8] = 00000000        [2ec] = 00000000
[2f0] = 00000000        [2f4] = 00000000        [2f8] = 00000000        [2fc] = 00000000
[300] = 00000000        [304] = 00000000        [308] = 00000000        [30c] = 00000000
[310] = 00000000        [314] = 00000000        [318] = 00000000        [31c] = 00000000
[320] = 00000000        [324] = 00000000        [328] = 00000000        [32c] = 00000000
[330] = 00000000        [334] = 00000000        [338] = 00000000        [33c] = 00000000
[340] = 00000000        [344] = 00000000        [348] = 00000000        [34c] = 00000000
[350] = 00000000        [354] = 00000000        [358] = 00000000        [35c] = 00000000
[360] = 00000000        [364] = 00000000        [368] = 00000000        [36c] = 00000000
[370] = 00000000        [374] = 00000000        [378] = 00000000        [37c] = 00000000
[380] = 00000000        [384] = 00000000        [388] = 00000000        [38c] = 00003000
[390] = 00000018        [394] = 00000000        [398] = 00000000        [39c] = 00000000
[3a0] = 0e0e0e0e        [3a4] = 00000000        [3a8] = 00000000        [3ac] = 00000000
[3b0] = 00000000        [3b4] = 00000000        [3b8] = 00000300        [3bc] = 00000000
[3c0] = 00000000        [3c4] = 00000000        [3c8] = 00000000        [3cc] = 00000000
[3d0] = 00000000        [3d4] = 00000000        [3d8] = 00000000        [3dc] = 00000000
[3e0] = 00000000        [3e4] = 00000000        [3e8] = 00000000        [3ec] = 00000000
[3f0] = 00000000        [3f4] = 00000000        [3f8] = 00000000        [3fc] = 00000000
[600] = 0e141985        [604] = 00040103        [608] = 000000e0        [60c] = 00090440
[610] = 00000000        [614] = 03200400        [618] = c20008fa        [61c] = 59000000
[620] = 00000000        [624] = c20008fa        [628] = 39000000        [62c] = 00000000
[630] = c20008fa        [634] = 51000000        [638] = 00000000        [63c] = 00000000
[640] = 00000230        [644] = 00000000        [648] = c2005ab2        [64c] = 00000000
[650] = 00000000        [654] = 00000000        [658] = 00000000        [65c] = 00000000
=============================================

===================================================================
                MT7621   stage1 code done
                CPU=500000000 HZ BUS=166666666 HZ
===================================================================

U-Boot 1.1.3 (Jan  6 2017 - 17:03:19)

Board: Ralink APSoC DRAM:   1 MB
relocate_code Pointer at: 8007c000



换过CPU ,换过内存,始终就是跑到这里卡住不走了....



点评

大神的这机器还在么?  详情 回复 发表于 2020-1-10 14:21
我的恩山、我的无线 The best wifi forum is right here.
回复

使用道具 举报

发表于 2020-1-10 14:21 来自手机 | 显示全部楼层
zyguowei 发表于 2018-12-31 01:56
===================================================================
                MT7621   stag ...

大神的这机器还在么?

点评

早就没在了...  详情 回复 发表于 2020-1-10 23:44
我的恩山、我的无线 The best wifi forum is right here.
回复

使用道具 举报

您需要登录后才可以回帖 登录 | 立即注册

本版积分规则

有疑问请添加管理员QQ86788181|手机版|小黑屋|Archiver|恩山无线论坛(常州市恩山计算机开发有限公司版权所有) ( 苏ICP备05084872号 )

GMT+8, 2024-3-29 10:40

Powered by Discuz! X3.5

© 2001-2024 Discuz! Team.

| 江苏省互联网有害信息举报中心 举报信箱:js12377 | @jischina.com.cn 举报电话:025-88802724 本站不良内容举报信箱:68610888@qq.com 举报电话:0519-86695797

快速回复 返回顶部 返回列表