2t qca9563 针脚图

dexi2009

电子放大镜拍的 一张一张拼的 凑活着看吧 闪存 16M 内存64M

ttl信息 uboot信息乱码 没复制

1. [    0.450000] console [ttyS0] enabled, bootconsole disabled
   
2. [    0.450000] console [ttyS0] enabled, bootconsole disabled
   
3. [    0.460000] m25p80 spi0.0: found gd25q128, expected m25p80
   
4. [    0.470000] m25p80 spi0.0: gd25q128 (16384 Kbytes)
   
5. [    0.470000] 7 cmdlinepart partitions found on MTD device spi0.0
   
6. [    0.480000] Creating 7 MTD partitions on "spi0.0":
   
7. [    0.490000] 0x000000000000-0x000000030000 : "u-boot"
   
8. [    0.490000] 0x000000030000-0x000000040000 : "config"
   
9. [    0.500000] 0x000000040000-0x000000090000 : "permanent"
   
10. [    0.500000] 0x000000090000-0x0000001b0000 : "kernel"
    
11. [    0.510000] 0x0000001b0000-0x000000ff0000 : "rootfs"
    
12. [    0.520000] mtd: partition "rootfs" set to be root filesystem
    
13. [    0.520000] mtd: partition "rootfs_data" created automatically, ofs=930000, len=200000
    
14. [    0.530000] 0x000000930000-0x000000b30000 : "rootfs_data"
    
15. [    0.540000] 0x000000ff0000-0x000001000000 : "art"
    
16. [    0.540000] 0x000000090000-0x000000ff0000 : "firmware"
    
17. [    0.550000] m25p80 spi0.1: found pm25lv512, expected m25p80
    
18. [    0.560000] m25p80 spi0.1: pm25lv512 (64 Kbytes)
    
19. [    0.700000] ag71xx_mdio: probed
    
20. [    0.700000] eth0: Atheros AG71xx at 0xb9000000, irq 4
    
21. [    1.280000] eth0: Atheros AR8327 switch driver attached.
    
22. [    4.210000] ag71xx ag71xx.0: eth0: connected to PHY at ag71xx-mdio.0:00 [uid=004dd036, driver=Atheros AR8216/AR8236/AR8316]
    
23. [    4.220000] init_module:price_compare!
    
24. [    4.230000] creat nlsock ok!
    
25. [    4.230000] TCP cubic registered
    
26. [    4.230000] NET: Registered protocol family 17
    
27. [    4.240000] Bridge firewalling registered
    
28. [    4.240000] 8021q: 802.1Q VLAN Support v1.8
    
29. [    4.250000] ### of_selftest(): No testcase data in device tree; not running tests
    
30. [    4.260000] VFS: Mounted root (squashfs filesystem) readonly on device 31:4.
    
31. [    4.270000] Freeing unused kernel memory: 180k freed
    
32. - preinit -
    
33. - fac_mode=N -
    
34. Press the [f] key and hit [enter] to enter failsafe mode
    
35. [    7.230000] eth0: link up (1000Mbps/Full duplex)
    
36. - regular preinit -
    
37. [    9.810000] JFFS2 notice: (468) jffs2_build_xattr_subsystem: complete building xattr subsystem, 1 of xdatum (0 unchecked, 0 orphan) and 23 of xref (0 dead, 0 orphan) found.
    
38. switching to jffs2
    
39. - init -
    
40. 
    
41. Please press Enter to activate this console. [   18.950000] netlink_kernel_create netlink socket ok. 30
    
42. [   19.050000] Button Hotplug driver version 0.4.1
    
43. [   19.170000] PPP generic driver version 2.4.2
    
44. [   19.190000] NET: Registered protocol family 24
    
45. [   19.220000] ip_tables: (C) 2000-2006 Netfilter Core Team
    
46. [   19.300000] nf_conntrack version 0.5.0 (962 buckets, 3848 max)
    
47. [   19.530000] xt_time: kernel timezone is +0800
    
48. [   19.740000] nf_conntrack_rtsp v0.6.21 loading
    
49. [   19.750000] nf_nat_rtsp v0.6.21 loading
    
50. [   24.110000] mem_manager: module license 'unspecified' taints kernel.
    
51. [   24.110000] Disabling lock debugging due to kernel taint
    
52. [   24.310000] ath_dfs: Version 2.0.0
    
53. [   24.310000] Copyright (c) 2005-2006 Atheros Communications, Inc. All Rights Reserved
    
54. [   25.310000] ath_hal: 0.9.17.1 (AR9380, DEBUG, REGOPS_FUNC, PRIVATE_DIAG, WRITE_EEPROM, 11D)
    
55. [   25.330000] ath_rate_atheros: Copyright (c) 2001-2005 Atheros Communications, Inc, All Rights Reserved
    
56. [   25.350000] ath_tx99: Version 2.0
    
57. [   25.350000] Copyright (c) 2010 Atheros Communications, Inc, All Rights Reserved
    
58. [   25.520000] ath_dev: Copyright (c) 2001-2007 Atheros Communications, Inc, All Rights Reserved
    
59. [   25.550000]  JET_PRINT: init_ath_wmac[240]: Checking devid: 3f
    
60. [   25.560000] __ath_attach: Set global_scn[0]
    
61. [   25.560000] *** All the minfree values should be <= ATH_TXBUF-32, otherwise default value will be used instead ***
    
62. [   25.570000] ACBKMinfree = 48
    
63. [   25.580000] ACBEMinfree = 32
    
64. [   25.580000] ACVIMinfree = 16
    
65. [   25.580000] ACVOMinfree = 0
    
66. [   25.590000] CABMinfree = 48
    
67. [   25.590000] UAPSDMinfree = 0
    
68. [   25.590000] ATH_TXBUF=1500
    
69. [   25.600000] Bootstrap clock 25MHz
    
70. [   25.610000] Enterprise mode: 0x03bda000
    
71. [   25.610000] Restoring Cal data from FS
    
72. [   25.610000] qdf_fs_read[59], Open File /tmp/wifi0.caldata SUCCESS!!file system magic:16914836super blocksize:4096inode 211file size:12064qdf_fs_read[79]: caldata data size mismatch, fsize=12064, cal_size=1088
    
73. [   25.630000] ART Version : -48.0.0
    
74. [   25.640000] SW Image Version : -48.0.0.0.0
    
75. [   25.640000] Board Revision :
    
76. [   25.640000] ar9300_attach: nf_2_nom -110 nf_2_max -60 nf_2_min -125
    
77. [   25.650000] Green-AP : Green-AP : Attached
    
78. [   25.650000]
    
79. [   25.660000] Starting random number generator thread
    
80. [   25.670000] ath_get_caps[6187] rx chainmask mismatch actual 3 sc_chainmak 0
    
81. [   25.680000] ath_get_caps[6162] tx chainmask mismatch actual 3 sc_chainmak 0
    
82. [   25.690000] ath_attach_dfs[12583] dfsdomain 1
    
83. [   25.700000] dfs_attach: event log enabled by default
    
84. [   25.710000] ath_attach: Set global_ic[1]..gloabl_ic ptr:82525a70
    
85. [   25.720000] phicomm_wifi_netlink: create netlink socket ok.
    
86. [   25.730000] ath_tx_paprd_init sc 82c98000 PAPRD disabled in HAL
    
87. [   25.730000] wifi0: Atheros 956X: mem_start: =0xb8100000, mem_end: =0xb8120000, irq=47
    
88. [   25.740000] ath_da_pci:  (Atheros/multi-bss)
    
89. [   26.240000] ath_ol_pci:  (Atheros/multi-bss)
    
90. [   26.240000] hif_pci_enable_bus: con_mode = 0x0, device_id = 0x56
    
91. [   26.250000] ath_ol_pci 0000:00:00.0: BAR 0: assigned [mem 0x12000000-0x121fffff 64bit]
    
92. [   26.260000] PCI: Enabling device 0000:00:00.0 (0000 -> 0002)
    
93. [   26.260000] hif_pci_enable_bus: hif_enable_pci done *********** QCA9888 *************hif_pci_enable_bus: hif_type = 0xe, target_type = 0xchif_pci_enable_bus: hif_pci_probe_tgt_wakeup donehif_target_sync: Loop checking FW signalhif_target_sync: Got FW signal, retries = 0hif_config_ce: ce_init donehif_config_ce: X, ret = 0hif_set_hia: Ehif_set_hia_extnd: E
    
94. [   26.300000] chip_id 0xc chip_revision 0x0
    
95. [   26.310000]
    
96. [   26.310000]  CLOCK PLL skipped
    
97. [   26.310000] hif_set_hia_extnd: setting the target pll frac ffffffff intval ffffffff
    
98. [   26.320000] hif_set_hia_extnd: no frac provided, skipping pre-configuring PLL
    
99. [   26.330000] hif_pci_bus_configure: hif_set_hia donehif_configure_irq: Ehif_pci_configure_legacy_irq: Ehif_pci_configure_legacy_irq: X, ret = 0hif_enable: X OKhif_napi_create: NAPI structures initializedhif_napi_create: NAPI id 6 created for pipe 5qca_napi_create: napi instance 32 created on pipe 4
    
100. [   26.360000] hif_napi_event: received evnt: CONF cmd; v = 1 (state=0x1)hif_napi_event: setting configuration to ON
     
101. [   26.370000] __ol_ath_attach() Allocated scn 82740380
     
102. [   26.380000] __ol_ath_attach: dev name wifi1
     
103. [   26.380000] ol_ath_attach interface_id 1
     
104. [   26.380000] ol_target_init() BMI inited.
     
105. [   26.390000] ol_target_init() BMI Get Target Info.
     
106. [   26.400000] Chip id: 0xc, chip version: 0x1000000
     
107. [   26.400000]
     
108. [   26.400000]  CE WAR Disabled
     
109. [   26.410000] NUM_DEV=1 FWMODE=0x2 FWSUBMODE=0x0 FWBR_BUF 0
     
110. [   26.410000] ol_target_init() configure Target .
     
111. [   26.420000]
     
112. [   26.420000]  Target Version is 1000000
     
113. [   26.420000]
     
114. [   26.420000]  Flash Download Address  c0000
     
115. [   26.430000] ol_transfer_bin_file: flash data file defined
     
116. [   26.430000] ol_transfer_bin_file[3797] Get Caldata for wifi1.
     
117. [   26.440000] qdf_fs_read[59], Open File /tmp/wifi1.caldata SUCCESS!!file system magic:16914836super blocksize:4096inode 212file size:12064qc98xx_verify_checksum: flash checksum passed: 0x7895
     
118. [   26.460000] ol_transfer_bin_file 3858: Download Flash data len 12064
     
119. [   26.460000] Board extended Data download address: 0x0
     
120. [   26.490000]
     
121. [   26.490000]  Board data initialized
     
122. [   26.500000] ol_ath_download_firmware: Download OTP, flash download ADDRESS 0xc0000
     
123. [   26.510000]
     
124. [   26.510000]  Selecting  OTP binary for CHIP Version 0
     
125. [   26.590000] ol_transfer_bin_file 3678: downloading file 0, Download data len 9116
     
126. [   26.630000]
     
127. [   26.630000]  First OTP send param 8000
     
128. [   26.880000] ol_ath_download_firmware :First OTP download and Execute is good address:0x5000 return param 4660
     
129. [   26.890000] ol_ath_download_firmware:##Board Id 20 , CHIP Id 0
     
130. [   26.890000] ol_ath_download_firmware: BOARDDATA DOWNLOAD TO address 0xc0000
     
131. [   26.900000] Warning : No board id matched. Selecting default boarddata file
     
132. [   26.910000]
     
133. [   26.910000]  wifi1: Selecting board data file name boarddata_0.bin
     
134. [   26.920000] ol_transfer_bin_file: Board Data File download to address=0xc0000 file name=QCA9888/hw.2/boarddata_0.bin
     
135. [   26.940000] ol_transfer_bin_file 3678: downloading file 3, Download data len 12064
     
136. [   26.950000] Board extended Data download address: 0x0
     
137. [   26.980000] ol_ath_download_firmware: Using 0x1234 for the remainder of init
     
138. [   26.980000]
     
139. [   26.980000]  Selecting  OTP binary for CHIP Version 0
     
140. [   27.000000] ol_transfer_bin_file 3678: downloading file 0, Download data len 9116
     
141. [   27.040000]
     
142. [   27.040000]  [Flash] : Ignore Module param
     
143. [   27.050000]
     
144. [   27.050000]  Second otp download Param 10000
     
145. [   27.310000] ol_ath_download_firmware : Second OTP download and Execute is good, param=0x0
     
146. [   27.310000]
     
147. [   27.310000]  Mission mode: Firmware CHIP Version 0
     
148. [   27.500000] ol_swap_seg_alloc: Successfully allocated memory for SWAP size=262144
     
149. [   27.520000] ol_swap_wlan_memory_expansion: length:261907 size_left:261927 dma_size_left:262144 fw_temp:c07c2004 fw_entry_size:261931
     
150. [   27.530000] ol_swap_wlan_memory_expansion: dma_virt_addr :a2600000 fw_temp: c07c2008 length: 261907
     
151. [   27.550000] Swap: bytes_left to copy: fw:16; dma_page:237
     
152. [   27.550000] ol_swap_wlan_memory_expansion: length:0 size_left:12 dma_size_left:237 fw_temp:c0801f1f fw_entry_size:261931
     
153. [   27.560000] Swap: wrong length read:0
     
154. [   27.570000] ol_swap_wlan_memory_expansion: Swap total_bytes copied: 261907 Target address 41b0c8
     
155. [   27.580000] scn=82740380  target_write_addr=41b0c8 seg_info=826c5210
     
156. [   27.580000] ol_transfer_swap_struct:Code swap structure successfully downloaded for bin type =2
     
157. [   27.590000] bin_filename=QCA9888/hw.2/athwlan.bin swap_filename=/lib/firmware/QCA9888/hw.2/athwlan.codeswap.bin
     
158. [   27.600000] ol_transfer_bin_file: Downloading firmware file: QCA9888/hw.2/athwlan.bin
     
159. [   28.020000] ol_transfer_bin_file 3678: downloading file 1, Download data len 388448
     
160. [   29.510000] ol_target_init() Download FW done.
     
161. [   29.510000] ol_ath_attach() WMI attached. wmi_handle 83884000
     
162. [   29.520000] wmi_unified_register_event_handler: Event id 62 is unavailable
     
163. [   29.520000] +htc_create ..  HIF :82ec4000-htc_create: (0x83953000)
     
164. [   29.530000] htc_wmi_init() HT Create . 83953000
     
165. [   29.530000] htc_wmi_init 7787 host_enable 0 nss_nwifi_offload 0
     
166. [   29.540000] ol_ath_set_default_tgt_config : AC Minfree buffer allocation through module param (umac.ko)
     
167. [   29.550000]  OL_ACBKMinfree : 0
     
168. [   29.550000]  OL_ACBEMinfree : 0
     
169. [   29.560000]  OL_ACVIMinfree : 0
     
170. [   29.560000]  OL_ACVOMinfree : 0
     
171. [   29.560000] hif_enable_fastpath, Enabling fastpath mode
     
172. [   29.570000] +HWT
     
173. [   29.570000] hif_completion_thread_startup: pipe_num:0 pipe_info:0x82ec706chif_completion_thread_startup: pipe_num:3 pipe_info:0x82ec712chif_completion_thread_startup: pipe_num:4 pipe_info:0x82ec716c
     
174. [   29.590000] -HWT
     
175. [   29.590000] Startup Mode-0 set
     
176. [   29.600000]
     
177. [   29.600000] <=== cfg max peer id 288 ====>
     
178. [   29.610000] htt_peer_map_timer_init Enter pdev 81dc5000 hrtimer 81dc59e0
     
179. [   29.610000]
     
180. [   29.610000]  htt_alloc_peer_map_mem : Alloc Success : host q vaddr 82dee400 paddr 2dee400
     
181. [   29.620000]
     
182. [   29.620000]  htt_alloc_peer_map_mem : Flush Interval Configured to 256 pkts
     
183. [   29.630000] ol_txrx_pdev_attach: 2500 tx desc's allocated ; range starts from 81840000
     
184. [   29.650000] Firmware_Build_Number:50
     
185. [   29.650000] FW wireless modes: 0x1f9001
     
186. [   29.650000] num_rf_chain:0x00000002  ht_cap_info:0x0000085b  vht_cap_info:0x339979b2  vht_supp_mcs:0x0000fffa
     
187. [   29.660000] wmi_service_coex_gpio 0, wmi_service_4_wire_coex_support 0, coex_version 0
     
188. [   29.670000]
     
189. [   29.670000] Sending Ext resource cfg: HOST PLATFORM as 1
     
190. [   29.670000] fw_feature_bitmap as 50 to TGT
     
191. [   29.680000] ol_ath_service_ready_event: tt_support: 1
     
192. [   29.690000] ol_ath_service_ready_event: periodic_chan_stats: 1
     
193. [   29.700000] ol_ath_service_ready_event: sw_cal_support_check_flag: 1
     
194. [   29.700000] Peer Caching Enabled ; num_peers = 38, num_active_peers = 25 num_tids = 50, num_vdevs = 5
     
195. [   29.710000] EXT NSS Supported
     
196. [   29.710000] idx 1 req 2  num_units 1 num_unit_info 12 unit size 256 actual units 26
     
197. [   29.720000] ol_ath_alloc_host_mem_chunk req_id 2 idx 0 num_units 26 unit_len 256,
     
198. [   29.730000] idx 2 req 3  num_units 1 num_unit_info 12 unit size 1024 actual units 26
     
199. [   29.740000] ol_ath_alloc_host_mem_chunk req_id 3 idx 1 num_units 26 unit_len 1024,
     
200. [   29.750000] idx 3 req 4  num_units 1 num_unit_info 12 unit size 4096 actual units 26
     
201. [   29.760000] ol_ath_alloc_host_mem_chunk req_id 4 idx 2 num_units 26 unit_len 4096,
     
202. [   29.760000] idx 0 req 1  num_units 0 num_unit_info 2 unit size 896 actual units 39
     
203. [   29.770000] ol_ath_alloc_host_mem_chunk req_id 1 idx 3 num_units 39 unit_len 896,
     
204. [   29.780000] idx 4 req 5  num_units 0 num_unit_info 2 unit size 2068 actual units 39
     
205. [   29.790000] ol_ath_alloc_host_mem_chunk req_id 5 idx 4 num_units 39 unit_len 2068,
     
206. [   29.790000] Support not added yet for Service 91
     
207. [   29.800000] Support not added yet for Service 92
     
208. [   29.800000] No EXT_MSG send INIT now
     
209. [   29.810000] chunk 0 len 6656 requested , ptr  0x2706000
     
210. [   29.810000] chunk 1 len 26624 requested , ptr  0x1838000
     
211. [   29.820000] chunk 2 len 106496 requested , ptr  0x18a0000
     
212. [   29.820000] chunk 3 len 34944 requested , ptr  0x18c0000
     
213. [   29.830000] chunk 4 len 80652 requested , ptr  0x18e0000
     
214. [   29.840000] chunk 5 len 0 requested , ptr  0xffffffff
     
215. [   29.840000] ol_ath_service_ready_event[4256] WAPI MBSSID 2
     
216. [   29.850000] smart_log_init: Smart logging Enabled buf=818d0000 (size=65536)
     
217. [   29.860000] Version = 16777216 3  status = 0
     
218. [   29.870000] ol_ath_connect_htc() WMI is ready
     
219. [   29.870000] htt_h2t_frag_desc_bank_cfg_msg - HTT_H2T_MSG_TYPE_FRAG_DESC_BANK_CFG sent to FW for radio ID = 1
     
220. [   29.880000] target uses HTT version 2.2; host uses 2.2
     
221. [   29.890000] ol_ath_attach() connect HTC.
     
222. [   29.900000] bypasswmi : 0
     
223. [   29.900000] ol_regdmn_start: reg-domain param: regdmn=0, countryName=, wModeSelect=FFFFFFFF, netBand=FFFFFFFF, extendedChanMode=0.
     
224. [   29.910000] ol_regdmn_init_channels: !avail mode 0x1f9001 (0x2) flags 0x2150
     
225. [   29.920000] ol_regdmn_init_channels: !avail mode 0x1f9001 (0x4) flags 0xa0
     
226. [   29.930000] ol_regdmn_init_channels: !avail mode 0x1f9001 (0x8) flags 0xc0
     
227. [   29.930000] ol_regdmn_init_channels: !avail mode 0x1f9001 (0x20) flags 0xd0
     
228. [   29.940000] ol_regdmn_init_channels: !avail mode 0x1f9001 (0x40) flags 0x150
     
229. [   29.950000] ol_regdmn_init_channels: !avail mode 0x1f9001 (0x800) flags 0x10080
     
230. [   29.960000] ol_regdmn_init_channels: !avail mode 0x1f9001 (0x2000) flags 0x20080
     
231. [   29.960000] ol_regdmn_init_channels: !avail mode 0x1f9001 (0x4000) flags 0x40080
     
232. [   29.970000] Add VHT80 channel: 5210
     
233. [   29.980000] Add VHT80 channel: 5290
     
234. [   29.980000] Add VHT80 channel: 5530
     
235. [   29.980000] Add VHT80 channel: 5610
     
236. [   29.990000] Add VHT80 channel: 5690
     
237. [   29.990000] Add VHT80 channel: 5775
     
238. [   29.990000] Skipping VHT80 channel 5825
     
239. [   30.000000] ol_regdmn_init_channels: !avail mode 0x1f9001 (0x200000) flags 0x4000100
     
240. [   30.010000] ol_regdmn_init_channels: !avail mode 0x1f9001 (0x400000) flags 0x8000100
     
241. [   30.010000] freq=58
     
242. [   30.020000] freq=106
     
243. [   30.020000] freq=122
     
244. [   30.020000] freq=138
     
245. [   30.020000] OL Resmgr Init-ed
     
246. [   30.030000] Green-AP : Green-AP : Attached
     
247. [   30.030000]
     
248. [   30.030000] Green-AP : Attached
     
249. [   30.040000] rate power table override is only supported for AR98XX
     
250. [   30.040000] ol_if_dfs_attach: called; ptr=8190997c, radar_info=82ce9b40
     
251. [   30.050000] dfs_attach: event log enabled by default
     
252. [   30.060000] >>>> CB Set   (null)
     
253. [   30.060000] ol_ath_attach() UMAC attach .
     
254. [   30.070000]
     
255. [   30.070000]  BURSTING enabled by default
     
256. [   30.070000] ol_ath_attach: Set global_ic[2] ..ptr:82525a70
     
257. [   30.080000] phicomm_wifi_netlink: create netlink socket ok.
     
258. [   30.080000] __ol_ath_attach: needed_headroom reservation 60
     
259. [   30.090000] ol_ath_thermal_mitigation_attach: --
     
260. [   30.090000] ol_ath_pci_probe num_radios=0, wifi_radios[0].sc = 82740380 wifi_radio_type = 2
     
261. [   30.100000] ath_sysfs_diag_init: diag_fsattr
     
262. [   30.520000] JFFS2 notice: (689) jffs2_build_xattr_subsystem: complete building xattr subsystem, 0 of xdatum (0 unchecked, 0 orphan) and 0 of xref (0 dead, 0 orphan) found.
     
263. [   30.550000] [wifi1] FWLOG: [34778] WAL_DBGID_TX_AC_BUFFER_SET ( 0x3, 0x1e, 0x94c, 0x94c, 0x0 )
     
264. [   30.550000] [wifi1] FWLOG: [34778] WAL_DBGID_TX_AC_BUFFER_SET ( 0x12, 0x1e, 0x94c, 0x94c, 0x0 )
     
265. [   30.560000] [wifi1] FWLOG: [34778] WAL_DBGID_TX_AC_BUFFER_SET ( 0x45, 0x1e, 0x94c, 0x94c, 0x0 )
     
266. [   30.570000] [wifi1] FWLOG: [34778] WAL_DBGID_TX_AC_BUFFER_SET ( 0x67, 0x1e, 0x94c, 0x94c, 0x0 )
     
267. [   30.580000] [wifi1] FWLOG: [34778] WAL_DBGID_TX_AC_BUFFER_SET ( 0x100, 0x11e1a300 )
     
268. [   30.590000] [wifi1] FWLOG: [34933] WAL_DBGID_PDEV_INFO_PRINT ( 0x3a, 0xa10, 0x160, 0x10, 0x0 )
     
269. [   30.600000] [wifi1] FWLOG: [34933] WAL_DBGID_PDEV_INFO_PRINT ( 0x3a, 0x10, 0x0, 0x10, 0x12 )
     
270. qcawifi disable radio wifi0
     
271. qcawifi disable radio wifi1
     
272. netifd_ubus_init(1204): connected as b5c91ed5
     
273. proto_shell_add_handler(814): Add handler for script ./dhcp.sh: dhcp
     
274. proto_shell_add_handler(814): Add handler for script ./ppp.sh: ppp
     
275. proto_shell_add_handler(814): Add handler for script ./ppp.sh: pppoe
     
276. config_init_wireless(362): device wifi0 not foun[   33.710000] device eth0.1 entered promiscuous mode
     
277. d!
     
278. config_init_[   33.720000] device eth0 entered promiscuous mode
     
279. wireless(362): device wifi0 not found!
     
280. config_init_wireless(362): device wifi0 not found!
     
281. config_init_wireless(362): device wifi1 not found!
     
282. config_init_wireless(362): device wifi1 not found!
     
283. config_init_wireless(362): device wifi1 not found!
     
284. [   35.500000] br-lan: port 1(eth0.1) entered forwarding state
     
285. [   35.500000] br-lan: port 1(eth0.1) entered forwarding state
     
286. [   35.510000] eth0: link up (1000Mbps/Full duplex)
     
287. [   37.500000] br-lan: port 1(eth0.1) entered forwarding state
     
288. qcawifi disable radio wifi0
     
289. qcawifi disable radio wifi1
     
290. qcawifi disable radio wifi0
     
291. qcawifi disable radio wifi1
     
292. qcawifi: enable radio wifi0
     
293. [   40.750000] ath_net80211_dfs_clist_update: called, cmd=1, nollist=  (null), nentries=0
     
294. [   40.760000] ath_attach_dfs[12583] dfsdomain 1
     
295. [   40.770000] dfs_attach: event log enabled by default
     
296. [   40.820000]  DCS for CW interference mitigation:   0
     
297. [   40.820000]  DCS for WLAN interference mitigation: 0
     
298. [   40.910000]  Disconnect_timeout value entered:10
     
299. [   40.920000]  reconfiguration_timeout value entered:60
     
300. [   41.040000] wlan_vap_create : enter. devhandle=0x82df0380, opmode=IEEE80211_M_HOSTAP, flags=0x1
     
301. [   41.050000] ieee80211_mbo_vattach:MBO Initialized
     
302. [   41.060000] ieee80211_oce_vattach: OCE Initialized
     
303. [   41.060000] wlan_vap_create : exit. devhandle=0x82df0380, vap=0x82e28000, opmode=IEEE80211_M_HOSTAP, flags=0x1.
     
304. [   41.070000] VAP device ath00 created osifp: (81ade380) os_if: (82e28000)
     
305. [   41.120000] siwfreq
     
306. [   41.120000] Set freq vap 0 stop send + 82e28000
     
307. [   41.120000] Set freq vap 0 stop send -82e28000
     
308. [   41.160000] Set wait done --82e28000
     
309. [   41.260000] [DEBUG] vap-0(ath00):set SIOC80211NWID, 11 characters
     
310. [   41.270000]
     
311. [   41.270000]  DES SSID SET=@PHICOMM_C3
     
312. [   41.730000]  ieee80211_ioctl_siwmode: imr.ifm_active=131712, new mode=3, valid=1
     
313. [   41.740000]  DEVICE IS DOWN ifname=ath00
     
314. [   41.750000]  DEVICE IS DOWN ifname=ath00
     
315. [   41.830000] 8021q: adding VLAN 0 to HW filter on device ath00
     
316. [   41.870000] device ath00 entered promiscuous mode
     
317. [   41.880000] br-lan: port 2(ath00) entered forwarding state
     
318. [   41.880000] br-lan: port 2(ath00) entered forwarding state
     
319. qcawifi: enable radio wifi1
     
320. [   42.030000] [ol_ath_iw_setcountry][1832] *p=43, *(p+1)=4e
     
321. [   42.030000] isCountryCodeValid: EEPROM regdomain 0x0
     
322. [   42.040000] ol_regdmn_init_channels: !avail mode 0x1f9001 (0x2) flags 0x2150
     
323. [   42.050000] ol_regdmn_init_channels: !avail mode 0x1f9001 (0x4) flags 0xa0
     
324. [   42.050000] ol_regdmn_init_channels: !avail mode 0x1f9001 (0x8) flags 0xc0
     
325. [   42.060000] ol_regdmn_init_channels: !avail mode 0x1f9001 (0x20) flags 0xd0
     
326. [   42.070000] ol_regdmn_init_channels: !avail mode 0x1f9001 (0x40) flags 0x150
     
327. [   42.080000] ol_regdmn_init_channels: !avail mode 0x1f9001 (0x800) flags 0x10080
     
328. [   42.080000] ol_regdmn_init_channels: !avail mode 0x1f9001 (0x2000) flags 0x20080
     
329. [   42.090000] ol_regdmn_init_channels: !avail mode 0x1f9001 (0x4000) flags 0x40080
     
330. [   42.100000] Add VHT80 channel: 5210
     
331. [   42.100000] Add VHT80 channel: 5290
     
332. [   42.110000] Add VHT80 channel: 5775
     
333. [   42.110000] Skipping VHT80 channel 5825
     
334. [   42.110000] ol_regdmn_init_channels: !avail mode 0x1f9001 (0x200000) flags 0x4000100
     
335. [   42.120000] ol_regdmn_init_channels: !avail mode 0x1f9001 (0x400000) flags 0x8000100
     
336. [   42.130000] freq=58
     
337. [   42.210000] set TXBF_SND_PERIOD: value 100 wmi_status 0
     
338. [   42.230000]  Disconnect_timeout value entered:10
     
339. [   42.240000]  reconfiguration_timeout value entered:60
     
340. [   42.310000] wlan_vap_create : enter. devhandle=0x82740380, opmode=IEEE80211_M_HOSTAP, flags=0x1
     
341. [   42.320000] send_vdev_create_cmd_non_tlv: ID = 0 Type = 1, Subtype = 0 VAP Addr = fc:7c:02:c9:3d:c5:
     
342. [   42.330000] ieee80211_mbo_vattach:MBO Initialized
     
343. [   42.330000] ieee80211_oce_vattach: OCE Initialized
     
344. [   42.340000] wlan_vap_create : exit. devhandle=0x82740380, vap=0x82cc8000, opmode=IEEE80211_M_HOSTAP, flags=0x1.
     
345. [   42.350000] Enabling TX checksum bit for the vap ath10 features 4000
     
346. [   42.350000] Enabling SG bit for the vap ath10 features 4000
     
347. [   42.360000] Enabling SG bit for the vap ath10 features 4000
     
348. [   42.360000] Enabling TSO bit for the vap ath10 features 4000
     
349. [   42.370000] Enabling LRO bit for the vap ath10 features 4000
     
350. [   42.380000] VAP device ath10 created osifp: (81adf380) os_if: (82cc8000)
     
351. [   42.400000] siwfreq
     
352. [   42.410000] Set freq vap 0 stop send + 82cc8000
     
353. [   42.410000] Set freq vap 0 stop send -82cc8000
     
354. [   42.450000] Set wait done --82cc8000
     
355. [   42.510000] ME Pool succesfully initialized vaddr - 81b8e000 paddr - 0
     
356. [   42.510000] num_elems = 100 buf_size - 64 pool_size = 7200
     
357. [   42.520000] Enable MCAST_TO_UCAST
     
358. [   42.550000] [wifi1] FWLOG: [47338] WAL_DBGID_PDEV_INFO_PRINT ( 0x57, 0x199, 0x1180, 0x10, 0x0 )
     
359. [   42.560000] [wifi1] FWLOG: [47338] WAL_DBGID_PDEV_INFO_PRINT ( 0x57, 0x10, 0x0, 0x10, 0x0 )
     
360. [   42.560000] [wifi1] FWLOG: [47408] WAL_DBGID_DEV_RESET ( 0xc01d, 0x474 )
     
361. [   42.570000] [wifi1] FWLOG: [47749] vap-0 WMI_CMD_PARAMS ( 0xff, 0x40, 0x1 )
     
362. [   42.600000] [DEBUG] vap-0(ath10):set SIOC80211NWID, 14 characters
     
363. [   42.610000]
     
364. [   42.610000]  DES SSID SET=@PHICOMM_C3_5G
     
365. [   42.930000]  ieee80211_ioctl_siwmode: imr.ifm_active=66176, new mode=3, valid=1
     
366. [   42.940000]  DEVICE IS DOWN ifname=ath10
     
367. [   42.950000]  DEVICE IS DOWN ifname=ath10
     
368. [   42.980000] Sending SCAN START cmd
     
369. [   42.980000] 8021q: adding VLAN 0 to HW filter on device ath10
     
370. [   43.020000] device ath10 entered promiscuous mode
     
371. [   43.020000] br-lan: port 3(ath10) entered forwarding state
     
372. [   43.030000] br-lan: port 3(ath10) entered forwarding state
     
373. [   43.550000] [wifi1] FWLOG: [48215] WAL channel change freq=5180, mode=0 flags=0 rx_ok=1 tx_ok=1
     
374. [   43.560000] [wifi1] FWLOG: [48523] WAL channel change freq=5200, mode=0 flags=0 rx_ok=1 tx_ok=1
     
375. [   43.880000] br-lan: port 2(ath00) entered forwarding state
     
376. [   44.600000] send event(id:4)(channel:1) error!
     
377. [   44.670000] [wifi1] FWLOG: [48838] WAL channel change freq=5220, mode=0 flags=0 rx_ok=1 tx_ok=1
     
378. [   44.670000] [wifi1] FWLOG: [49152] WAL channel change freq=5240, mode=0 flags=0 rx_ok=1 tx_ok=1
     
379. [   44.680000] [wifi1] FWLOG: [49466] WAL channel change freq=5745, mode=0 flags=0 rx_ok=1 tx_ok=1
     
380. [   44.690000] [wifi1] FWLOG: [49780] WAL channel change freq=5765, mode=0 flags=0 rx_ok=1 tx_ok=1
     
381. [   44.760000] Input domain:p.to;www.p.to;phicomm.me;www.phicomm.me ip:192.168.2.1 .
     
382. [   44.770000] hijack domain name:p.to;www.p.to;phicomm.me;www.phicomm.me .
     
383. [   45.030000] br-lan: port 3(ath10) entered forwarding state
     
384. [   45.550000] [wifi1] FWLOG: [50094] WAL channel change freq=5785, mode=0 flags=0 rx_ok=1 tx_ok=1
     
385. [   45.560000] [wifi1] FWLOG: [50408] WAL channel change freq=5805, mode=0 flags=0 rx_ok=1 tx_ok=1
     
386. [   45.570000] [wifi1] FWLOG: [50722] WAL channel change freq=5825, mode=0 flags=0 rx_ok=1 tx_ok=1
     
387. [   45.740000] send_vdev_down_cmd_non_tlv for vap 0
     
388. [   45.750000] send event(id:4)(channel:44) error!
     
389. [   45.750000] OL vap_start +
     
390. [   45.750000] VDEV START
     
391. [   45.760000] OL vap_start -
     
392. [   45.760000] ol_ath_vap_set_param: Now supported MGMT RATE is 6000(kbps) and rate code: 0x3
     
393. [   45.940000] ol_vdev_start_resp_ev for vap 0 (83884000)
     
394. [   45.950000] send_wmm_update_cmd_non_tlv:
     
395. [   45.950000] su bfee 1 mu bfee 0 su bfer 1 mu bfer 1 impl bf 0 sounding dim 1
     
396. [   45.960000] send_vdev_up_cmd_non_tlv for vap 0
     
397. [   46.550000] [wifi1] FWLOG: [51040] RESMGR_OCS_GEN_PERIODIC_NOA ( 0x0 )
     
398. [   46.550000] [wifi1] FWLOG: [51040] RESMGR_OCS_GEN_PERIODIC_NOA ( 0x0 )
     
399. [   46.560000] [wifi1] FWLOG: [51051] vap-0 VDEV_MGR_VDEV_START ( 0x1464, 0x2, 0x0, 0x0 )
     
400. [   46.570000] [wifi1] FWLOG: [51051] WAL channel change freq=5220, mode=10 flags=0 rx_ok=1 tx_ok=1
     
401. [   46.580000] [wifi1] FWLOG: [51239] VDEV_MGR_VDEV_START_RESP ( 0x0 )
     
402. [   46.580000] [wifi1] FWLOG: [51261] VDEV_MGR_HP_START_TIME ( 0x0, 0x1464, 0xf6e001 )
     
403. [   46.590000] [wifi1] FWLOG: [51261] RESMGR_OCS_GEN_PERIODIC_NOA ( 0x1 )
     
404. [   46.600000] [wifi1] FWLOG: [51261] RESMGR_OCS_GEN_PERIODIC_NOA ( 0x0 )
     
405. [   46.610000] [wifi1] FWLOG: [51261] VDEV_MGR_AP_TBTT_CONFIG ( 0x0, 0x1464, 0x0, 0x0 )
     
406. [   49.960000] fast-classifier: starting up
     
407. [   49.960000] fast-classifier: registered
     
408. [   54.570000] phicomm id:4(pid:2178) connect ok!
     

复制代码

拉侧旋

支持下，这东西就是type c线不好diy

听我说爱你宝贝

可以改USB了

若如初见

不错，高清图

jrz3055112

我就佩服你这样的牛人！！！QCA9563+QCA9886+QCA8337

qq222g

16m不是128吗，怎么是127呢

猫猫猫猫

16M不容易啊

dexi2009

qq222g 发表于 2018-5-15 18:25
16m不是128吗，怎么是127呢

上面印刷显示127 ttl显示  gd25q128  淘宝有卖gd25q127 gd25q128 都是16M

hades2014

6666,,,,,支持，，

温柔背后

qq222g 发表于 2018-5-15 18:25
16m不是128吗，怎么是127呢

25Q128,25是封装定义，12指的是128（128/8=16M）不要看后面那个8或者7！