找回密码
 立即注册

QQ登录

只需一步,快速开始

搜索
广告投放联系QQ68610888
查看: 39702|回复: 47

贝壳云折腾刷机请教

[复制链接]
发表于 2018-11-23 22:35 | 显示全部楼层 |阅读模式
最近咸鱼看到贝壳云 很便宜,也是矿难的机器。有大侠想折腾一下么?我今天买到已经拆开了

4个USB3.0, CPU RK3328, RAM 1G , 4个USB3.0通过GL3520桥接出来的。

今天折腾了一下,打开盖子,reset在里面板子上。 板子上海预留了一个USB2.0的焊盘,我按照webpad大神刷联想粒子云的OMV固件的教程刷了一遍,开不了机器了~~~~~~仍旧可以反复刷,可以进bootloader,系统进不去。

我的恩山、我的无线 The best wifi forum is right here.
 楼主| 发表于 2018-11-23 22:46 | 显示全部楼层
有人感兴趣我就加图。 这个机器需要拆机,reset在里面,然后我是自己焊了4根线,连到内部的USB2.0的焊盘上。
我刷机的流程和固件,完全是按webpad刷联想粒子云的教程来的。
刷OMV后,连接hdmi是显示命令行的,所以我觉得问题应该不大。
我的恩山、我的无线 The best wifi forum is right here.
回复

使用道具 举报

发表于 2018-11-24 15:06 | 显示全部楼层
不错,可以折腾。 家里已经有2个N1,1个粒子矿云了,这玩意儿多了也没用哈
我的恩山、我的无线 The best wifi forum is right here.
回复

使用道具 举报

 楼主| 发表于 2018-11-24 21:18 | 显示全部楼层
更新下进展~~~ 进不去系统,随便刷刷不死。 rk提供的AndroidTool工具很强大,随便搞没事。
我的恩山、我的无线 The best wifi forum is right here.
回复

使用道具 举报

 楼主| 发表于 2018-11-25 11:03 | 显示全部楼层
反复重启 一次启动期间打印的内容。

INFO:    PSCI Power Domain Map:
INFO:      Domain Node : Level 2, parent_node -1, State ON (0x0)
INFO:      Domain Node : Level 1, parent_node 0, State ON (0x0)
INFO:      Domain Node : Level 0, parent_node 0, State ON (0x0)
INFO:      Domain Node : Level 0, parent_node 0, State ON (0x0)
INFO:      CPU Node : MPID 0x0, parent_node 1, State ON (0x0)
INFO:      CPU Node : MPID 0x1, parent_node 1, State ON (0x0)
INFO:      CPU Node : MPID 0x2, parent_node 1, State ON (0x0)
INFO:      CPU Node : MPID 0x3, parent_node 1, State ON (0x0)
DDR version 1.13 20180428
ID:0xFFF
In
SRX
DDR3
786MHz
Bus Width=32 Col=10 Bank=8 Row=15 CS=1 Die Bus-Width=16 Size=1024MB
ddrconfig:1
OUT

U-Boot SPL 2017.09-rockchip-ayufan-1033-gdf02018479 (Aug 06 2018 - 22:28:57)
setup_ddr_param  1
booted from eMMC
Trying to boot from MMC1
NOTICE:  BL31: v1.3(debug):9d3f591
NOTICE:  BL31: Built : 14:39:02, Jan 17 2018
NOTICE:  BL31:Rockchip release version: v1.3
INFO:    ARM GICv2 driver initialized
INFO:    Using opteed sec cpu_context!
INFO:    boot cpu mask: 1
INFO:    plat_rockchip_pmu_init: pd status 0xe
INFO:    BL31: Initializing runtime services
WARNING: No OPTEE provided by BL2 boot loader, Booting device without OPTEE initialization. SMC`s destined for OPTEE will return SMC_UNK
ERROR:   Error initializing runtime service opteed_fast
INFO:    BL31: Preparing for EL3 exit to normal world
INFO:    Entry point address = 0x200000
INFO:    SPSR = 0x3c9


U-Boot 2017.09-rockchip-ayufan-1033-gdf02018479 (Aug 06 2018 - 22:29:07 +0000)

Model: Pine64 Rock64
DRAM:  1022 MiB
MMC:   rksdmmc@ff520000: 0, rksdmmc@ff500000: 1
SF: unrecognized JEDEC id bytes: ff, ff, ff
*** Warning - spi_flash_probe_bus_cs() failed, using default environment

In:    serial@ff130000
Out:   serial@ff130000
Err:   serial@ff130000
Model: Pine64 Rock64
misc_init_r
cpuid=55524b50303930313900000000111d06
serial=b5cdadcf31585c7
normal boot
Net:   eth0: ethernet@ff540000
Hit any key to stop autoboot:  0
switch to partitions #0, OK
mmc0(part 0) is current device
Scanning mmc 0:7...
Found /boot/extlinux/extlinux.conf
Retrieving file: /boot/extlinux/extlinux.conf
1055 bytes read in 12 ms (85 KiB/s)
select kernel
1:      kernel-4.4.154-1122-rockchip-ayufan-g7859b9b904a9
2:      kernel-4.4.154-1122-rockchip-ayufan-g7859b9b904a9-memtest
Enter choice: 1:        kernel-4.4.154-1122-rockchip-ayufan-g7859b9b904a9
Retrieving file: /boot/initrd.img-4.4.154-1122-rockchip-ayufan-g7859b9b904a9
5192449 bytes read in 153 ms (32.4 MiB/s)
Retrieving file: /boot/vmlinuz-4.4.154-1122-rockchip-ayufan-g7859b9b904a9
19986440 bytes read in 554 ms (34.4 MiB/s)
append: rw panic=10 init=/sbin/init coherent_pool=1M ethaddr=8e:29:47:45:f3:ff eth1addr=8e:29:47:45:f3:1f serial=b5cdadcf31585c7 cgroup_enable=cpuset cgroup_memory=1 cgroup_enable=memory swapaccount=1 root=LABEL=linux-root rootwait rootfstype=ext4
Retrieving file: /boot/dtbs/4.4.154-1122-rockchip-ayufan-g7859b9b904a9/rockchip/rk3328-rock64.dtb
70953 bytes read in 36 ms (1.9 MiB/s)
## Flattened Device Tree blob at 01f00000
   Booting using the fdt blob at 0x1f00000
   Loading Ramdisk to 3da0e000, end 3df01b01 ... OK
   Loading Device Tree to 000000003d9f9000, end 000000003da0d528 ... OK

Starting kernel ...

[    0.000000] Booting Linux on physical CPU 0x0
[    0.000000] Initializing cgroup subsys cpuset
[    0.000000] Initializing cgroup subsys cpu
[    0.000000] Initializing cgroup subsys cpuacct
[    0.000000] Linux version 4.4.154-1122-rockchip-ayufan-g7859b9b904a9 (root@runner-f725ff63-project-5943294-concurrent-0) (gcc version 7.3.0 (Ubuntu/Linaro 7.3.0-16ubuntu3) ) #1 SMP Mon Oct 1 07:32:42 UTC 2018
[    0.000000] Boot CPU: AArch64 Processor [410fd034]
[    0.000000] earlycon: Early serial console at MMIO32 0xff130000 (options '')
[    0.000000] bootconsole [uart0] enabled
[    0.000000] psci: probing for conduit method from DT.
[    0.000000] psci: PSCIv1.0 detected in firmware.
[    0.000000] psci: Using standard PSCI v0.2 function IDs
[    0.000000] psci: MIGRATE_INFO_TYPE not supported.
[    0.000000] PERCPU: Embedded 21 pages/cpu @ffffffc03ff42000 s46248 r8192 d31576 u86016
[    0.000000] Detected VIPT I-cache on CPU0
[    0.000000] CPU features: enabling workaround for ARM erratum 845719
[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 257544
[    0.000000] Kernel command line: earlycon=uart8250,mmio32,0xff130000 swiotlb=1 kpti=0 rw panic=10 init=/sbin/init coherent_pool=1M ethaddr=8e:29:47:45:f3:ff eth1addr=8e:29:47:45:f3:1f serial=b5cdadcf31585c7 cgroup_enable=cpuset cgroup_memory=1 cgroup_enable=memory swapaccount=1 root=LABEL=linux-root rootwait rootfstype=ext4
[    0.000000] PID hash table entries: 4096 (order: 3, 32768 bytes)
[    0.000000] Dentry cache hash table entries: 131072 (order: 8, 1048576 bytes)
[    0.000000] Inode-cache hash table entries: 65536 (order: 7, 524288 bytes)
[    0.000000] software IO TLB [mem 0x3fdfa000-0x3fe3a000] (0MB) mapped at [ffffffc03fdfa000-ffffffc03fe39fff]
[    0.000000] Memory: 1002060K/1046528K available (12158K kernel code, 1726K rwdata, 4388K rodata, 1216K init, 768K bss, 44468K reserved, 0K cma-reserved)
[    0.000000] Virtual kernel memory layout:
[    0.000000]     modules : 0xffffff8000000000 - 0xffffff8008000000   (   128 MB)
[    0.000000]     vmalloc : 0xffffff8008000000 - 0xffffffbdbfff0000   (   246 GB)
[    0.000000]       .init : 0xffffff80090b0000 - 0xffffff80091e0000   (  1216 KB)
[    0.000000]       .text : 0xffffff8008080000 - 0xffffff8008c60000   ( 12160 KB)
[    0.000000]     .rodata : 0xffffff8008c60000 - 0xffffff80090b0000   (  4416 KB)
[    0.000000]       .data : 0xffffff80091e0000 - 0xffffff800938f808   (  1727 KB)
[    0.000000]     vmemmap : 0xffffffbdc0000000 - 0xffffffbfc0000000   (     8 GB maximum)
[    0.000000]               0xffffffbdc0008000 - 0xffffffbdc1000000   (    15 MB actual)
[    0.000000]     fixed   : 0xffffffbffe7fb000 - 0xffffffbffec00000   (  4116 KB)
[    0.000000]     PCI I/O : 0xffffffbffee00000 - 0xffffffbfffe00000   (    16 MB)
[    0.000000]     memory  : 0xffffffc000200000 - 0xffffffc040000000   (  1022 MB)
[    0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1
[    0.000000] Hierarchical RCU implementation.
[    0.000000]  Build-time adjustment of leaf fanout to 64.
[    0.000000]  RCU restricting CPUs from NR_CPUS=8 to nr_cpu_ids=4.
[    0.000000] RCU: Adjusting geometry for rcu_fanout_leaf=64, nr_cpu_ids=4
[    0.000000] NR_IRQS:64 nr_irqs:64 0
[    0.000000] GIC: Using split EOI/Deactivate mode
[    0.000000] Architected cp15 timer(s) running at 24.00MHz (phys).
[    0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x588fe9dc0, max_idle_ns: 440795202592 ns
[    0.000007] sched_clock: 56 bits at 24MHz, resolution 41ns, wraps every 4398046511097ns
[    0.001856] Console: colour dummy device 80x25
[    0.002270] console [tty0] enabled
[    0.002594] bootconsole [uart0] disabled
[    0.000000] Booting Linux on physical CPU 0x0
[    0.000000] Initializing cgroup subsys cpuset
[    0.000000] Initializing cgroup subsys cpu
[    0.000000] Initializing cgroup subsys cpuacct
[    0.000000] Linux version 4.4.154-1122-rockchip-ayufan-g7859b9b904a9 (root@runner-f725ff63-project-5943294-concurrent-0) (gcc version 7.3.0 (Ubuntu/Linaro 7.3.0-16ubuntu3) ) #1 SMP Mon Oct 1 07:32:42 UTC 2018
[    0.000000] Boot CPU: AArch64 Processor [410fd034]
[    0.000000] earlycon: Early serial console at MMIO32 0xff130000 (options '')
[    0.000000] bootconsole [uart0] enabled
[    0.000000] psci: probing for conduit method from DT.
[    0.000000] psci: PSCIv1.0 detected in firmware.
[    0.000000] psci: Using standard PSCI v0.2 function IDs
[    0.000000] psci: MIGRATE_INFO_TYPE not supported.
[    0.000000] PERCPU: Embedded 21 pages/cpu @ffffffc03ff42000 s46248 r8192 d31576 u86016
[    0.000000] Detected VIPT I-cache on CPU0
[    0.000000] CPU features: enabling workaround for ARM erratum 845719
[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 257544
[    0.000000] Kernel command line: earlycon=uart8250,mmio32,0xff130000 swiotlb=1 kpti=0 rw panic=10 init=/sbin/init coherent_pool=1M ethaddr=8e:29:47:45:f3:ff eth1addr=8e:29:47:45:f3:1f serial=b5cdadcf31585c7 cgroup_enable=cpuset cgroup_memory=1 cgroup_enable=memory swapaccount=1 root=LABEL=linux-root rootwait rootfstype=ext4
[    0.000000] PID hash table entries: 4096 (order: 3, 32768 bytes)
[    0.000000] Dentry cache hash table entries: 131072 (order: 8, 1048576 bytes)
[    0.000000] Inode-cache hash table entries: 65536 (order: 7, 524288 bytes)
[    0.000000] software IO TLB [mem 0x3fdfa000-0x3fe3a000] (0MB) mapped at [ffffffc03fdfa000-ffffffc03fe39fff]
[    0.000000] Memory: 1002060K/1046528K available (12158K kernel code, 1726K rwdata, 4388K rodata, 1216K init, 768K bss, 44468K reserved, 0K cma-reserved)
[    0.000000] Virtual kernel memory layout:
[    0.000000]     modules : 0xffffff8000000000 - 0xffffff8008000000   (   128 MB)
[    0.000000]     vmalloc : 0xffffff8008000000 - 0xffffffbdbfff0000   (   246 GB)
[    0.000000]       .init : 0xffffff80090b0000 - 0xffffff80091e0000   (  1216 KB)
[    0.000000]       .text : 0xffffff8008080000 - 0xffffff8008c60000   ( 12160 KB)
[    0.000000]     .rodata : 0xffffff8008c60000 - 0xffffff80090b0000   (  4416 KB)
[    0.000000]       .data : 0xffffff80091e0000 - 0xffffff800938f808   (  1727 KB)
[    0.000000]     vmemmap : 0xffffffbdc0000000 - 0xffffffbfc0000000   (     8 GB maximum)
[    0.000000]               0xffffffbdc0008000 - 0xffffffbdc1000000   (    15 MB actual)
[    0.000000]     fixed   : 0xffffffbffe7fb000 - 0xffffffbffec00000   (  4116 KB)
[    0.000000]     PCI I/O : 0xffffffbffee00000 - 0xffffffbfffe00000   (    16 MB)
[    0.000000]     memory  : 0xffffffc000200000 - 0xffffffc040000000   (  1022 MB)
[    0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1
[    0.000000] Hierarchical RCU implementation.
[    0.000000]  Build-time adjustment of leaf fanout to 64.
[    0.000000]  RCU restricting CPUs from NR_CPUS=8 to nr_cpu_ids=4.
[    0.000000] RCU: Adjusting geometry for rcu_fanout_leaf=64, nr_cpu_ids=4
[    0.000000] NR_IRQS:64 nr_irqs:64 0
[    0.000000] GIC: Using split EOI/Deactivate mode
[    0.000000] Architected cp15 timer(s) running at 24.00MHz (phys).
[    0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x588fe9dc0, max_idle_ns: 440795202592 ns
[    0.000007] sched_clock: 56 bits at 24MHz, resolution 41ns, wraps every 4398046511097ns
[    0.001856] Console: colour dummy device 80x25
[    0.002270] console [tty0] enabled
[    0.002594] bootconsole [uart0] disabled
[    0.002990] Calibrating delay loop (skipped), value calculated using timer frequency.. 48.00 BogoMIPS (lpj=24000)
[    0.003030] pid_max: default: 32768 minimum: 301
[    0.003169] Security Framework initialized
[    0.003189] Yama: becoming mindful.
[    0.003219] AppArmor: AppArmor disabled by boot time parameter
[    0.003292] Mount-cache hash table entries: 2048 (order: 2, 16384 bytes)
[    0.003320] Mountpoint-cache hash table entries: 2048 (order: 2, 16384 bytes)
[    0.004170] Initializing cgroup subsys io
[    0.004203] Initializing cgroup subsys memory
[    0.004249] Initializing cgroup subsys devices
[    0.004275] Initializing cgroup subsys freezer
[    0.004300] Initializing cgroup subsys net_cls
[    0.004330] Initializing cgroup subsys perf_event
[    0.004357] Initializing cgroup subsys net_prio
[    0.004388] Initializing cgroup subsys hugetlb
[    0.004410] Initializing cgroup subsys pids
[    0.004474] ftrace: allocating 45075 entries in 177 pages
[    0.129778] sched-energy: CPU device node has no sched-energy-costs
[    0.129812] Invalid sched_group_energy for CPU0
[    0.129830] CPU0: update cpu_capacity 1024
[    0.129903] ASID allocator initialised with 32768 entries
[    0.135366] Detected VIPT I-cache on CPU1
[    0.135422] Invalid sched_group_energy for CPU1
[    0.135428] CPU1: update cpu_capacity 1024
[    0.135433] CPU1: Booted secondary processor [410fd034]
[    0.136158] Detected VIPT I-cache on CPU2
[    0.136203] Invalid sched_group_energy for CPU2
[    0.136208] CPU2: update cpu_capacity 1024
[    0.136213] CPU2: Booted secondary processor [410fd034]
[    0.136908] Detected VIPT I-cache on CPU3
[    0.136952] Invalid sched_group_energy for CPU3
[    0.136956] CPU3: update cpu_capacity 1024
[    0.136961] CPU3: Booted secondary processor [410fd034]
[    0.137063] Brought up 4 CPUs
[    0.137521] SMP: Total of 4 processors activated.
[    0.137565] CPU features: kernel page table isolation forced OFF by command line option
[    0.137664] CPU: All CPU(s) started at EL2
[    0.137735] alternatives: patching kernel code
[    0.138024] Invalid sched_group_energy for CPU3
[    0.138070] Invalid sched_group_energy for Cluster3
[    0.138110] Invalid sched_group_energy for CPU2
[    0.138151] Invalid sched_group_energy for Cluster2
[    0.138191] Invalid sched_group_energy for CPU1
[    0.138232] Invalid sched_group_energy for Cluster1
[    0.138273] Invalid sched_group_energy for CPU0
[    0.138313] Invalid sched_group_energy for Cluster0
[    0.139159] devtmpfs: initialized
[    0.162757] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 1911260446275000 ns
[    0.162860] futex hash table entries: 1024 (order: 4, 65536 bytes)
[    0.163505] xor: measuring software checksum speed
[    0.173131]    8regs     :  1080.000 MB/sec
[    0.183219]    8regs_prefetch:   968.000 MB/sec
[    0.193304]    32regs    :  1456.000 MB/sec
[    0.203395]    32regs_prefetch:  1224.000 MB/sec
[    0.203437] xor: using function: 32regs (1456.000 MB/sec)
[    0.203504] pinctrl core: initialized pinctrl subsystem
[    0.206303] Failed to find legacy iommu devices
[    0.207016] NET: Registered protocol family 16
[    0.211397] cpuidle: using governor ladder
[    0.215426] cpuidle: using governor menu
[    0.216274] vdso: 2 pages (1 code @ ffffff8008c66000, 1 data @ ffffff80091e4000)
[    0.216377] hw-breakpoint: found 6 breakpoint and 4 watchpoint registers.
[    0.216906] DMA: preallocated 1024 KiB pool for atomic allocations
[    0.286624] raid6: int64x1  gen()   199 MB/s
[    0.303668] raid6: int64x1  xor()   189 MB/s
[    0.320866] raid6: int64x2  gen()   324 MB/s
[    0.338048] raid6: int64x2  xor()   255 MB/s
[    0.355290] raid6: int64x4  gen()   480 MB/s
[    0.372384] raid6: int64x4  xor()   330 MB/s
[    0.389602] raid6: int64x8  gen()   386 MB/s
[    0.406767] raid6: int64x8  xor()   302 MB/s
[    0.424090] raid6: neonx1   gen()   363 MB/s
[    0.441111] raid6: neonx1   xor()   332 MB/s
[    0.458295] raid6: neonx2   gen()   546 MB/s
[    0.475509] raid6: neonx2   xor()   488 MB/s
[    0.492693] raid6: neonx4   gen()   742 MB/s
[    0.509883] raid6: neonx4   xor()   556 MB/s
[    0.527083] raid6: neonx8   gen()   761 MB/s
[    0.544273] raid6: neonx8   xor()   576 MB/s
[    0.544317] raid6: using algorithm neonx8 gen() 761 MB/s
[    0.544357] raid6: .... xor() 576 MB/s, rmw enabled
[    0.544398] raid6: using intx1 recovery algorithm
[    0.544867] mpp venc_srv: mpp_probe enter
[    0.544937] mpp venc_srv: init success
[    0.547324] vcc_sd: regulator get failed, ret=-517
[    0.547787] vcc_host_5v: supplied by vcc_sys
[    0.549033] iommu: Adding device ff350000.vpu_service to group 0
[    0.549167] iommu: Adding device ff351000.avsd to group 1
[    0.549286] iommu: Adding device ff360000.rkvdec to group 2
[    0.549444] iommu: Adding device ff330000.h265e to group 3
[    0.549565] iommu: Adding device ff340000.vepu to group 4
[    0.549697] iommu: Adding device ff370000.vop to group 5
[    0.550773] rk_iommu ff360480.iommu: can't get aclk
[    0.550829] rk_iommu ff360480.iommu: can't get hclk
[    0.552257] SCSI subsystem initialized
[    0.552896] usbcore: registered new interface driver usbfs
[    0.553015] usbcore: registered new interface driver hub
[    0.553155] usbcore: registered new device driver usb
[    0.553357] media: Linux media interface: v0.10
[    0.553485] Linux video capture interface: v2.00
[    0.553640] pps_core: LinuxPPS API ver. 1 registered
[    0.553683] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
[    0.553787] PTP clock support registered
[    0.555615] Advanced Linux Sound Architecture Driver Initialized.
[    0.556546] Bluetooth: Core ver 2.21
[    0.556635] NET: Registered protocol family 31
[    0.556677] Bluetooth: HCI device and connection manager initialized
[    0.556729] Bluetooth: HCI socket layer initialized
[    0.556777] Bluetooth: L2CAP socket layer initialized
[    0.556852] Bluetooth: SCO socket layer initialized
[    0.557581] NetLabel: Initializing
[    0.557626] NetLabel:  domain hash size = 128
[    0.557666] NetLabel:  protocols = UNLABELED CIPSOv4
[    0.557775] NetLabel:  unlabeled traffic allowed by default
[    0.558329] rockchip-cpuinfo cpuinfo: Serial         : b5cdadcf31585c7a
[    0.559662] clocksource: Switched to clocksource arch_sys_counter
[    0.690811] NET: Registered protocol family 2
[    0.691592] TCP established hash table entries: 8192 (order: 4, 65536 bytes)
[    0.691805] TCP bind hash table entries: 8192 (order: 6, 262144 bytes)
[    0.692199] TCP: Hash tables configured (established 8192 bind 8192)
[    0.692334] UDP hash table entries: 512 (order: 3, 49152 bytes)
[    0.692443] UDP-Lite hash table entries: 512 (order: 3, 49152 bytes)
[    0.692891] NET: Registered protocol family 1
[    0.693437] RPC: Registered named UNIX socket transport module.
[    0.693485] RPC: Registered udp transport module.
[    0.693525] RPC: Registered tcp transport module.
[    0.693566] RPC: Registered tcp NFSv4.1 backchannel transport module.
[    0.694484] Trying to unpack rootfs image as initramfs...
[    1.079154] Freeing initrd memory: 5068K
[    1.080455] hw perfevents: enabled with armv8_cortex_a53 PMU driver, 7 counters available
[    1.081819] kvm [1]: 8-bit VMID
[    1.081861] kvm [1]: Hyp mode initialized successfully
[    1.082363] kvm [1]: interrupt-controller@ff814000 IRQ44
[    1.082775] kvm [1]: timer IRQ3
[    1.086938] audit: initializing netlink subsys (disabled)
[    1.087053] audit: type=2000 audit(1.009:1): initialized
[    1.088285] HugeTLB registered 2 MB page size, pre-allocated 0 pages
[    1.101708] VFS: Disk quotas dquot_6.6.0
[    1.102013] VFS: Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
[    1.104597] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[    1.106783] NFS: Registering the id_resolver key type
[    1.106890] Key type id_resolver registered
[    1.106932] Key type id_legacy registered
[    1.106993] Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
[    1.108164] fuse init (API version 7.23)
[    1.109505] JFS: nTxBlock = 7868, nTxLock = 62945
[    1.115824] SGI XFS with ACLs, security attributes, realtime, no debug enabled
[    1.119570] Key type big_key registered
[    1.119738]
[    1.119738] TEE Core Framework initialization (ver 1:0.1)
[    1.119831] TEE armv7 Driver initialization
[    1.120324] tz_tee_probe: name="armv7sec", id=0, pdev_name="armv7sec.0"
[    1.120375] TEE core: Alloc the misc device "opteearmtz00" (id=0)
[    1.120769] TEE Core: Register the misc device "opteearmtz00" (id=0,minor=62)
[    1.126691] NET: Registered protocol family 38
[    1.126783] Key type asymmetric registered
[    1.126833] Asymmetric key parser 'x509' registered
[    1.127198] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 248)
[    1.127479] io scheduler noop registered
[    1.127533] io scheduler deadline registered (default)
[    1.127634] io scheduler cfq registered
[    1.130034] phy phy-ff450000.syscon:usb2-phy@100.1: Failed to get VBUS supply regulator
[    1.131144] rockchip-u3phy ff470000.usb3-phy: Failed to get VBUS supply regulator
[    1.133727] rockchip-u3phy ff470000.usb3-phy: Rockchip u3phy initialized successfully
[    1.137736] rk-vcodec vpu_combo: no regulator for vcodec
[    1.138061] rk-vcodec vpu_combo: failed on clk_get clk_cabac
[    1.138116] rk-vcodec vpu_combo: failed on clk_get clk_core
[    1.138248] platform ff350000.vpu_service: probe device
[    1.138630] platform ff350000.vpu_service: drm allocator with mmu enabled
[    1.139576] platform ff351000.avsd: probe device
[    1.140044] platform ff351000.avsd: drm allocator with mmu enabled
[    1.142218] rk-vcodec vpu_combo: could not find power_model node
[    1.142273] rk-vcodec vpu_combo: init success
[    1.142733] rk-vcodec ff360000.rkvdec: no regulator for vcodec
[    1.142830] rk-vcodec ff360000.rkvdec: parent devfreq is disabled
[    1.143466] rk-vcodec ff360000.rkvdec: probe device
[    1.144015] rk-vcodec ff360000.rkvdec: drm allocator with mmu enabled
[    1.144890] rk-vcodec ff360000.rkvdec: init success
[    1.145893] probe device ff330000.h265e
[    1.146293] mpp_dev ff330000.h265e: try to get iommu dev ffffffc03ebfe010
[    1.146836] mpp_dev ff330000.h265e: resource ready, register device
[    1.147355] probe device ff340000.vepu
[    1.147764] mpp_dev ff340000.vepu: try to get iommu dev ffffffc03ebfe810
[    1.148185] mpp_dev ff340000.vepu: resource ready, register device
[    1.151431] dma-pl330 ff1f0000.dmac: Loaded driver for PL330 DMAC-241330
[    1.151492] dma-pl330 ff1f0000.dmac:         DBUFF-128x8bytes Num_Chans-8 Num_Peri-20 Num_Events-16
[    1.153229] Serial: 8250/16550 driver, 5 ports, IRQ sharing disabled
[    1.155993] ff130000.serial: ttyS2 at MMIO 0xff130000 (irq = 13, base_baud = 1500000) is a 16550A
[    1.271283] console [ttyS2] enabled
[    1.273302] [drm] Initialized drm 1.1.0 20060810
[    1.278099] [drm] Rockchip DRM driver version: v1.0.1
[    1.278856] rockchip-drm display-subsystem: devfreq is not set
[    1.280147] rockchip-drm display-subsystem: bound ff370000.vop (ops 0xffffff8008d31f38)
[    1.281336] i2c i2c-4: of_i2c: modalias failure on /hdmi@ff3c0000/ports
[    1.281995] dwhdmi-rockchip ff3c0000.hdmi: registered DesignWare HDMI I2C bus driver
[    1.282884] dwhdmi-rockchip ff3c0000.hdmi: Detected HDMI TX controller v2.11a with HDCP (inno_dw_hdmi_phy2)
[    1.284987] rockchip-drm display-subsystem: bound ff3c0000.hdmi (ops 0xffffff8008d27f40)
[    1.285796] [drm] Supports vblank timestamp caching Rev 2 (21.10.2013).
[    1.286416] [drm] No driver support for vblank timestamp query.
[    1.287074] rockchip-drm display-subsystem: failed to parse display resources
[    1.287802] rockchip-drm display-subsystem: No connectors reported connected with modes
[    1.288627] [drm] Cannot find any crtc or sizes - going 1024x768
[    1.314889] Console: switching to colour frame buffer device 128x48
[    1.335381] rockchip-drm display-subsystem: fb0:  frame buffer device
[    1.342378] usbcore: registered new interface driver udl
[    1.345459] Unable to detect cache hierarchy for CPU 0
[    1.347416] brd: module loaded
[    1.356974] loop: module loaded
[    1.357446] lkdtm: No crash points registered, enable through debugfs
[    1.360624] rockchip-spi ff190000.spi: no high_speed pinctrl state
[    1.362344] m25p80 spi32766.0: unrecognized JEDEC id bytes: ff, ff, ff
[    1.363238] m25p80: probe of spi32766.0 failed with error -2
[    1.366332] force_sf_dma_mode is ignored if force_thresh_dma_mode is set.
[    1.367404] rk_gmac-dwmac ff540000.ethernet: clock input or output? (input).
[    1.368331] rk_gmac-dwmac ff540000.ethernet: TX delay(0x26).
[    1.369078] rk_gmac-dwmac ff540000.ethernet: RX delay(0x11).
[    1.369830] rk_gmac-dwmac ff540000.ethernet: integrated PHY? (no).
[    1.370882] rk_gmac-dwmac ff540000.ethernet: cannot get clock clk_mac_speed
[    1.371787] rk_gmac-dwmac ff540000.ethernet: clock input from PHY
[    1.377580] rk_gmac-dwmac ff540000.ethernet: init for RGMII
[    1.378469] stmmac - user ID: 0x10, Synopsys ID: 0x35
[    1.379135]  Ring mode enabled
[    1.379533]  DMA HW capability register supported
[    1.380131]  Normal descriptors
[    1.380571]  RX Checksum Offload Engine supported (type 2)
[    1.381285]  Wake-Up On Lan supported
[    1.390190]  Enable RX Mitigation via HW Watchdog Timer
[    1.471161] libphy: stmmac: probed
[    1.479849] eth%d: PHY ID 001cc916 at 0 IRQ POLL (stmmac-0:00) active
[    1.488837] eth%d: PHY ID 001cc916 at 1 IRQ POLL (stmmac-0:01)
[    1.499088] Rockchip WiFi SYS interface (V1.00) ...
[    1.507942] usbcore: registered new interface driver cdc_ether
[    1.516867] usbcore: registered new interface driver rndis_host
[    1.527681] phy phy-ff470000.usb3-phy.2: u3phy u2 power on
[    1.536467] phy phy-ff470000.usb3-phy.3: u3phy u3 power on
[    1.546295] ff580000.usb supply vusb_d not found, using dummy regulator
[    1.555168] ff580000.usb supply vusb_a not found, using dummy regulator
[    1.576326] dwc2 ff580000.usb: DWC OTG Controller
[    1.584690] dwc2 ff580000.usb: new USB bus registered, assigned bus number 1
[    1.593214] dwc2 ff580000.usb: irq 41, io mem 0xff580000
[    1.601706] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
[    1.610032] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    1.618305] usb usb1: Product: DWC OTG Controller
[    1.626211] usb usb1: Manufacturer: Linux 4.4.154-1122-rockchip-ayufan-g7859b9b904a9 dwc2_hsotg
[    1.634632] usb usb1: SerialNumber: ff580000.usb
[    1.643518] hub 1-0:1.0: USB hub found
[    1.651389] hub 1-0:1.0: 1 port detected
[    1.660487] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[    1.668594] ehci-pci: EHCI PCI platform driver
[    1.676450] ehci-platform: EHCI generic platform driver
[    1.686897] ehci-platform ff5c0000.usb: EHCI Host Controller
[    1.695017] ehci-platform ff5c0000.usb: new USB bus registered, assigned bus number 2
[    1.703200] ehci-platform ff5c0000.usb: irq 42, io mem 0xff5c0000
[    1.716697] ehci-platform ff5c0000.usb: USB 2.0 started, EHCI 1.00
[    1.724794] usb usb2: New USB device found, idVendor=1d6b, idProduct=0002
[    1.732768] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    1.740743] usb usb2: Product: EHCI Host Controller
[    1.748419] usb usb2: Manufacturer: Linux 4.4.154-1122-rockchip-ayufan-g7859b9b904a9 ehci_hcd
[    1.756595] usb usb2: SerialNumber: ff5c0000.usb
[    1.765204] hub 2-0:1.0: USB hub found
[    1.772865] hub 2-0:1.0: 1 port detected
[    1.781041] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[    1.788888] ohci-platform: OHCI generic platform driver
[    1.797210] ohci-platform ff5d0000.usb: Generic Platform OHCI controller
[    1.805629] ohci-platform ff5d0000.usb: new USB bus registered, assigned bus number 3
[    1.814059] ohci-platform ff5d0000.usb: irq 43, io mem 0xff5d0000
[    1.876959] usb usb3: New USB device found, idVendor=1d6b, idProduct=0001
[    1.885296] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    1.893666] usb usb3: Product: Generic Platform OHCI controller
[    1.901905] usb usb3: Manufacturer: Linux 4.4.154-1122-rockchip-ayufan-g7859b9b904a9 ohci_hcd
[    1.910585] usb usb3: SerialNumber: ff5d0000.usb
[    1.919793] hub 3-0:1.0: USB hub found
[    1.928035] hub 3-0:1.0: 1 port detected
[    1.937417] xhci-hcd xhci-hcd.9.auto: xHCI Host Controller
[    1.946090] xhci-hcd xhci-hcd.9.auto: new USB bus registered, assigned bus number 4
[    1.954924] xhci-hcd xhci-hcd.9.auto: hcc params 0x0220fe64 hci version 0x110 quirks 0x00210010
[    1.963725] xhci-hcd xhci-hcd.9.auto: irq 179, io mem 0xff600000
[    1.972502] usb usb4: New USB device found, idVendor=1d6b, idProduct=0002
[    1.981172] usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    1.989857] usb usb4: Product: xHCI Host Controller
[    1.998389] usb usb4: Manufacturer: Linux 4.4.154-1122-rockchip-ayufan-g7859b9b904a9 xhci-hcd
[    2.007432] usb usb4: SerialNumber: xhci-hcd.9.auto
[    2.017121] hub 4-0:1.0: USB hub found
[    2.025807] hub 4-0:1.0: 1 port detected
[    2.035014] xhci-hcd xhci-hcd.9.auto: xHCI Host Controller
[    2.044194] xhci-hcd xhci-hcd.9.auto: new USB bus registered, assigned bus number 5
[    2.053437] usb usb5: We don't know the algorithms for LPM for this host, disabling LPM.
[    2.062870] usb usb5: New USB device found, idVendor=1d6b, idProduct=0003
[    2.071962] usb usb5: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    2.081098] usb usb5: Product: xHCI Host Controller
[    2.089946] usb usb5: Manufacturer: Linux 4.4.154-1122-rockchip-ayufan-g7859b9b904a9 xhci-hcd
[    2.099234] usb usb5: SerialNumber: xhci-hcd.9.auto
[    2.108958] hub 5-0:1.0: USB hub found
[    2.117741] hub 5-0:1.0: 1 port detected
[    2.128595] usbcore: registered new interface driver iforce
[    2.137723] usbcore: registered new interface driver xpad
[    2.147064] usbcore: registered new interface driver usbtouchscreen
[    2.156927] i2c /dev entries driver
[    2.167495] rk808 1-0018: failed to read the chip id at 0x17
[    2.176452] rk3x-i2c ff160000.i2c: Initialized RK3xxx I2C bus at ffffff8009b7a000
[    2.187351] IR NEC protocol handler initialized
[    2.196207] IR RC5(x/sz) protocol handler initialized
[    2.205049] IR RC6 protocol handler initialized
[    2.213813] IR JVC protocol handler initialized
[    2.222418] IR Sony protocol handler initialized
[    2.230944] IR SANYO protocol handler initialized
[    2.239360] IR Sharp protocol handler initialized
[    2.247682] IR MCE Keyboard/mouse protocol handler initialized
[    2.256228] IR XMP protocol handler initialized
[    2.265625] usbcore: registered new interface driver uvcvideo
[    2.274143] USB Video Class driver (1.1.1)
[    2.285626] rockchip-thermal ff250000.tsadc: tsadc is probed successfully!
[    2.295812] device-mapper: ioctl: 4.34.0-ioctl (2015-10-28) initialised: dm-devel@redhat.com
[    2.304872] Bluetooth: Virtual HCI driver ver 1.5
[    2.313691] Bluetooth: HCI UART driver ver 2.3
[    2.322230] Bluetooth: HCI UART protocol H4 registered
[    2.330737] Bluetooth: HCI UART protocol LL registered
[    2.339027] Bluetooth: HCI UART protocol ATH3K registered
[    2.347312] usbcore: registered new interface driver bfusb
[    2.347701] usb 4-1: new high-speed USB device number 2 using xhci-hcd
[    2.364089] usbcore: registered new interface driver btusb
[    2.372789] cpu cpu0: Failed to get leakage
[    2.381064] cpu cpu0: Failed to get reg
[    2.389559] sdhci: Secure Digital Host Controller Interface driver
[    2.397836] sdhci: Copyright(c) Pierre Ossman
[    2.405837] Synopsys Designware Multimedia Card Interface Driver
[    2.415420] dwmmc_rockchip ff520000.dwmmc: IDMAC supports 32-bit address mode.
[    2.423920] dwmmc_rockchip ff520000.dwmmc: Using internal DMA controller.
[    2.432168] dwmmc_rockchip ff520000.dwmmc: Version ID is 270a
[    2.440215] dwmmc_rockchip ff520000.dwmmc: DW MMC controller at irq 38,32 bit host data width,256 deep fifo
[    2.449628] dwmmc_rockchip ff500000.dwmmc: IDMAC supports 32-bit address mode.
[    2.458103] dwmmc_rockchip ff500000.dwmmc: Using internal DMA controller.
[    2.466421] dwmmc_rockchip ff500000.dwmmc: Version ID is 270a
[    2.474611] dwmmc_rockchip ff500000.dwmmc: DW MMC controller at irq 39,32 bit host data width,256 deep fifo
[    2.483730] sdhci-pltfm: SDHCI platform and OF driver helper
[    2.493123] hidraw: raw HID events driver (C) Jiri Kosina
[    2.507327] usbcore: registered new interface driver usbhid
[    2.515502] usbhid: USB HID core driver
[    2.522845] usb 4-1: New USB device found, idVendor=05e3, idProduct=0610
[    2.522856] usb 4-1: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[    2.522864] usb 4-1: Product: USB2.0 Hub
[    2.522872] usb 4-1: Manufacturer: GenesysLogic
[    2.534031] hub 4-1:1.0: USB hub found
[    2.535166] hub 4-1:1.0: 4 ports detected
[    2.574444] usbcore: registered new interface driver snd-usb-audio
[    2.584215] rk3328-codec ff410000.codec: spk_depop_time use default value.
[    2.599961] u32 classifier
[    2.607852] Netfilter messages via NETLINK v0.30.
[    2.615902] ip_set: protocol 6
[    2.616970] usb 5-1: new SuperSpeed USB device number 2 using xhci-hcd
[    2.631739] usb 5-1: New USB device found, idVendor=05e3, idProduct=0616
[    2.631749] usb 5-1: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[    2.631757] usb 5-1: Product: USB3.0 Hub
[    2.631765] usb 5-1: Manufacturer: GenesysLogic
[    2.646356] hub 5-1:1.0: USB hub found
[    2.646779] hub 5-1:1.0: 4 ports detected
[    2.681511] Initializing XFRM netlink socket
[    2.690596] NET: Registered protocol family 10
[    2.700104] NET: Registered protocol family 17
[    2.708019] NET: Registered protocol family 15
[    2.715694] bridge: automatic filtering via arp/ip/ip6tables has been deprecated. Update your scripts to load br_netfilter if you need this.
[    2.731770] Bridge firewalling registered
[    2.739881] Bluetooth: RFCOMM socket layer initialized
[    2.748117] Bluetooth: RFCOMM ver 1.11
[    2.756209] Bluetooth: HIDP (Human Interface Emulation) ver 1.2
[    2.764549] Bluetooth: HIDP socket layer initialized
[    2.772775] 8021q: 802.1Q VLAN Support v1.8
[    2.780823] [WLAN_RFKILL]: Enter rfkill_wlan_init
[    2.789196] [BT_RFKILL]: Enter rfkill_rk_init
[    2.797567] Key type dns_resolver registered
[    2.806621] Registered cp15_barrier emulation handler
[    2.814739] Registered setend emulation handler
[    2.823843] registered taskstats version 1
[    2.835132] Btrfs loaded, integrity-checker=on
[    2.843146] BTRFS: selftest: Running btrfs free space cache tests
[    2.851313] BTRFS: selftest: Running extent only tests
[    2.859240] BTRFS: selftest: Running bitmap only tests
[    2.866989] BTRFS: selftest: Running bitmap and extent tests
[    2.874755] BTRFS: selftest: Running space stealing from bitmap to extent
[    2.884406] BTRFS: selftest: Free space cache tests finished
[    2.892096] BTRFS: selftest: Running extent buffer operation tests
[    2.892880] BTRFS: selftest: Running btrfs_split_item tests
[    2.907218] BTRFS: selftest: Running find delalloc tests
[    3.379266] BTRFS: selftest: Running btrfs_get_extent tests
[    3.386984] BTRFS: selftest: Running hole first btrfs_get_extent test
[    3.394418] BTRFS: selftest: Running outstanding_extents tests
[    3.401767] BTRFS: selftest: Running qgroup tests
[    3.408805] BTRFS: selftest: Qgroup basic add
[    3.415895] BTRFS: selftest: Qgroup multiple refs test
[    3.453134] Key type encrypted registered
[    3.460695] pvtm list NULL
[    3.469867] dwmmc_rockchip ff520000.dwmmc: IDMAC supports 32-bit address mode.
[    3.477282] dwmmc_rockchip ff520000.dwmmc: Using internal DMA controller.
[    3.484478] dwmmc_rockchip ff520000.dwmmc: Version ID is 270a
[    3.491539] dwmmc_rockchip ff520000.dwmmc: DW MMC controller at irq 38,32 bit host data width,256 deep fifo
[    3.500915] dwmmc_rockchip ff500000.dwmmc: IDMAC supports 32-bit address mode.
[    3.508317] dwmmc_rockchip ff500000.dwmmc: Using internal DMA controller.
[    3.515555] dwmmc_rockchip ff500000.dwmmc: Version ID is 270a
[    3.522672] dwmmc_rockchip ff500000.dwmmc: DW MMC controller at irq 39,32 bit host data width,256 deep fifo
[    3.553596] asoc-simple-card sound: rk3328-hifi <-> ff010000.i2s mapping ok
[    3.561915] asoc-simple-card sound: snd-soc-dummy-dai <-> ff010000.i2s mapping ok
[    3.572618] asoc-simple-card spdif-sound: dit-hifi <-> ff030000.spdif mapping ok
[    3.583540] dwmmc_rockchip ff520000.dwmmc: IDMAC supports 32-bit address mode.
[    3.591403] dwmmc_rockchip ff520000.dwmmc: Using internal DMA controller.
[    3.599133] dwmmc_rockchip ff520000.dwmmc: Version ID is 270a
[    3.606831] dwmmc_rockchip ff520000.dwmmc: DW MMC controller at irq 38,32 bit host data width,256 deep fifo
[    3.616808] dwmmc_rockchip ff500000.dwmmc: IDMAC supports 32-bit address mode.
[    3.624779] dwmmc_rockchip ff500000.dwmmc: Using internal DMA controller.
[    3.632386] dwmmc_rockchip ff500000.dwmmc: Version ID is 270a
[    3.639851] dwmmc_rockchip ff500000.dwmmc: DW MMC controller at irq 39,32 bit host data width,256 deep fifo
[    3.649991] hctosys: unable to open rtc device (rtc0)
[    3.657673] of_cfs_init
[    3.665024] of_cfs_init: OK
[    3.691050] vcc_sd: disabling
[    3.699122] ALSA device list:
[    3.706287]   #0: I2S
[    3.713279]   #1: SPDIF
[    3.720480] of_dma_request_slave_channel: dma-names property of node '/serial@ff130000' missing or empty
[    3.728438] ttyS2 - failed to request DMA, use interrupt mode
[    3.736835] Freeing unused kernel memory: 1216K
Loading, please wait...
starting version 232
[    3.796075] random: systemd-udevd: uninitialized urandom read (16 bytes read, 3 bits of entropy available)
[    3.802016] random: udevadm: uninitialized urandom read (16 bytes read, 3 bits of entropy available)
[    3.802266] random: udevadm: uninitialized urandom read (16 bytes read, 3 bits of entropy available)
[    3.802359] random: udevadm: uninitialized urandom read (16 bytes read, 3 bits of entropy available)
[    3.802978] random: udevadm: uninitialized urandom read (16 bytes read, 3 bits of entropy available)
[    3.803510] random: udevadm: uninitialized urandom read (16 bytes read, 3 bits of entropy available)
[    3.804083] random: udevadm: uninitialized urandom read (16 bytes read, 3 bits of entropy available)
[    3.804730] random: udevadm: uninitialized urandom read (16 bytes read, 3 bits of entropy available)
[    3.805806] random: udevadm: uninitialized urandom read (16 bytes read, 3 bits of entropy available)
[    3.807065] random: udevadm: uninitialized urandom read (16 bytes read, 3 bits of entropy available)
Begin: Loading essential drivers ... [    4.234513] md: linear personality registered for level -1
[    4.247996] md: multipath personality registered for level -4
[    4.261431] md: raid0 personality registered for level 0
[    4.275717] md: raid1 personality registered for level 1
[    4.288979] async_tx: api initialized (async)
[    4.304104] md: raid6 personality registered for level 6
[    4.311807] md: raid5 personality registered for level 5
[    4.319306] md: raid4 personality registered for level 4
[    4.343597] md: raid10 personality registered for level 10
done.
Begin: Running /scripts/init-premount ... done.
Begin: Mounting root file system ... Begin: Running /scripts/local-top ... done.
Begin: Running /scripts/local-premount ... Scanning for Btrfs filesystems
done.
Begin: Waiting for root file system ... Begin: Running /scripts/local-block ... done.
Begin: Running /scripts/local-block ... done.
Begin: Running /scripts/local-block ... done.
Begin: Running /scripts/local-block ... done.
Begin: Running /scripts/local-block ... done.
Begin: Running /scripts/local-block ... done.
Begin: Running /scripts/local-block ... done.
Begin: Running /scripts/local-block ... done.
Begin: Running /scripts/local-block ... done.
Begin: Running /scripts/local-block ... done.
Begin: Running /scripts/local-block ... done.
Begin: Running /scripts/local-block ... done.
Begin: Running /scripts/local-block ... done.
Begin: Running /scripts/local-block ... done.
Begin: Running /scripts/local-block ... done.
Begin: Running /scripts/local-block ... done.
Begin: Running /scripts/local-block ... done.
Begin: Running /scripts/local-block ... done.
Begin: Running /scripts/local-block ... done.
Begin: Running /scripts/local-block ... mdadm: error opening /dev/md?*: No such file or directory
/scripts/local-block/mdadm: 58: /scripts/local-block/mdadm: rm: not found
done.
Begin: Running /scripts/local-block ... done.
Begin: Running /scripts/local-block ... done.
Begin: Running /scripts/local-block ... done.
Begin: Running /scripts/local-block ... done.
Begin: Running /scripts/local-block ... done.
Begin: Running /scripts/local-block ... done.
Begin: Running /scripts/local-block ... done.
Begin: Running /scripts/local-block ... done.
Begin: Running /scripts/local-block ... done.
Begin: Running /scripts/local-block ... done.
done.
Gave up waiting for root file system device.  Common problems:
- Boot args (cat /proc/cmdline)
   - Check rootdelay= (did the system wait long enough?)
- Missing modules (cat /proc/modules; ls /dev)
ALERT!  LABEL=linux-root does not exist.  Dropping to a shell!
Rebooting automatically due to panic= boot argument
[   45.526177] kvm: exiting hardware virtualization
[   45.534394] rk-vcodec ff360000.rkvdec: shutdown
[   45.541799] rk-vcodec vpu_combo: shutdown
[   45.549056] reboot: Restarting system
我的恩山、我的无线 The best wifi forum is right here.
回复

使用道具 举报

 楼主| 发表于 2018-11-25 14:56 | 显示全部楼层
rootfs找不到怎么办,不晓得怎么下手了。
我的恩山、我的无线 The best wifi forum is right here.
回复

使用道具 举报

发表于 2018-11-27 13:26 | 显示全部楼层
贝壳云多少钱?emmc容量是多少啊?看起来也是rk3288的芯片,但是貌似不是rock64,估计可以刷rk3288 cc的rom。

点评

我买的89包邮,刷CC的kernal都起不来。  详情 回复 发表于 2018-11-27 15:11
我的恩山、我的无线 The best wifi forum is right here.
回复

使用道具 举报

 楼主| 发表于 2018-11-27 15:11 | 显示全部楼层
xingwen320 发表于 2018-11-27 13:26
贝壳云多少钱?emmc容量是多少啊?看起来也是rk3288的芯片,但是貌似不是rock64,估计可以刷rk3288 cc的rom ...

我买的89包邮,刷CC的kernal都起不来。
我的恩山、我的无线 The best wifi forum is right here.
回复

使用道具 举报

 楼主| 发表于 2018-11-27 15:12 | 显示全部楼层
刚刚把rock64的img刷到u盘上,从U盘启动。可以进入omv了。但是没有网卡驱动,找不到网络

点评

贝壳云支持优盘启动么???  详情 回复 发表于 2020-12-31 16:36
我的恩山、我的无线 The best wifi forum is right here.
回复

使用道具 举报

发表于 2018-11-27 19:46 来自手机 | 显示全部楼层
试试看老毛子的armbian

点评

链接在哪里? 不是N1用的吧?CPU不一样啊  详情 回复 发表于 2018-11-27 21:03
我的恩山、我的无线 The best wifi forum is right here.
回复

使用道具 举报

 楼主| 发表于 2018-11-27 21:03 | 显示全部楼层
哈哈哈哈哈1 发表于 2018-11-27 19:46
试试看老毛子的armbian

链接在哪里? 不是N1用的吧?CPU不一样啊
我的恩山、我的无线 The best wifi forum is right here.
回复

使用道具 举报

发表于 2018-11-28 07:38 来自手机 | 显示全部楼层
https://forum.armbian.com/topic/8082-armbian-for-tv-box-rk3328/
我的恩山、我的无线 The best wifi forum is right here.
回复

使用道具 举报

发表于 2018-11-28 08:14 来自手机 | 显示全部楼层
老哥发点板子图片吧,我也买了周末准备玩

点评

这个板非常简单,你周末拆开就知道了,那些焊接点一目了然,机器已经被拿走了~~~拍不了。  详情 回复 发表于 2018-11-29 18:14
我的恩山、我的无线 The best wifi forum is right here.
回复

使用道具 举报

 楼主| 发表于 2018-11-29 18:14 | 显示全部楼层
哈哈哈哈哈1 发表于 2018-11-28 08:14
老哥发点板子图片吧,我也买了周末准备玩

这个板非常简单,你周末拆开就知道了,那些焊接点一目了然,机器已经被拿走了~~~拍不了。
我的恩山、我的无线 The best wifi forum is right here.
回复

使用道具 举报

发表于 2018-11-29 22:34 来自手机 | 显示全部楼层
老哥是图片里这四个带锡的点吗?能告诉我线序吗?手头没万用表

本帖子中包含更多资源

您需要 登录 才可以下载或查看,没有账号?立即注册

×

点评

刷了其他固件之后,按reset进入,使用AnroidTool 无法进入maskrom模式,需要先短接pcb背面的两个触点。插上usb线,听到电脑提示咚咚后,就可以松开。 然后使用AndroidTool,点高级功能,boot那一栏,随便选择一个rk  详情 回复 发表于 2018-11-30 11:22
感觉你地软件水平比较高诶,希望您搞得定。 我之前地进展,再描述清楚一些: rock64的任何固件,刷到这个机器里,都是找不到rootfs,所以我就使用u盘也写入了同样的img文件(贝壳云的emmc没有擦除,也是同样的img  详情 回复 发表于 2018-11-30 11:03
图片从左向右 Vcc D- D+ Gnd。 这是标准的usb2.0接口,所以大片敷铜的那个是地。 其他的按正常排序就好了。 这个板子在emmc 背面有两个触点,短接的话,可以强制进入maskrom模式  详情 回复 发表于 2018-11-30 10:50
我的恩山、我的无线 The best wifi forum is right here.
回复

使用道具 举报

您需要登录后才可以回帖 登录 | 立即注册

本版积分规则

有疑问请添加管理员QQ86788181|手机版|小黑屋|Archiver|恩山无线论坛(常州市恩山计算机开发有限公司版权所有) ( 苏ICP备05084872号 )

GMT+8, 2024-4-25 21:06

Powered by Discuz! X3.5

© 2001-2024 Discuz! Team.

| 江苏省互联网有害信息举报中心 举报信箱:js12377 | @jischina.com.cn 举报电话:025-88802724 本站不良内容举报信箱:68610888@qq.com 举报电话:0519-86695797

快速回复 返回顶部 返回列表