找回密码
 立即注册

QQ登录

只需一步,快速开始

搜索
广告投放联系QQ68610888
查看: 4222|回复: 19

各位前辈们帮帮忙看下b860av1.1t的 TTL信息

[复制链接]
发表于 2020-4-4 22:54 | 显示全部楼层 |阅读模式
本帖最后由 `wifi` 于 2020-4-4 22:58 编辑

高手们帮帮忙看下b860av1.1t的 TTL信息,现像是上电不断重复下面的内容,应该怎样救砖??


U-Boot 2015.01-g53bf894-dirty (Nov 29 2019 - 20:32:00)

DRAM:  1 GiB
init - init amlnand_phy here
chipinfo - show aml chip information
device[dev] - show or set current device
partition* [part] - show or set current partition
plane[dev] - show or set current plane mode
read - addr off|partition size
write - addr off|partition size
    read/write 'size' bytes starting at offset 'off'
    to/from memory address 'addr', skipping bad blocks.
erase[clean|whole][off size] - erase 'size' bytesfrom
    offset 'off' (entire device if not specified)
dump  addr off
    show the raw data to addr at offset off
read_byte - addr off|partition size
write_byte - addr off|partition size
    read_byte/write_byte 'size' bytes starting at offset 'off'
    to/from memory address 'addr', skipping bad blocks.
devread  - addr off|partition size
devwrite - addr off|partition size
    read/write 'size' bytes starting at offset 'off' in device[dev]
    to/from memory address 'addr', skipping bad blocks.
deverase[whole][off size] - erase 'size' bytes from
    offset 'off' (entire device if not specified) in device[dev]
markbad addr - mark block bad at addr
mark_reserved reserved_blk_NO -mark reserved_blk_ NO bad
ldevice[dev] - show/get nftl(logic) device by name
rom_read/write addr off cnt - read/write uboot.
boot - show boot flagdtb_read/write addr cnt - read/write dtd.
dtb_erase - erase dtb!
key_read/write addr cnt - read/write dtd.
key_erase - erase keys!
scrub3d  - Erase (scrub) nand in SLC/MLC mode. switch back to MLC!

store init flag
store read name addr off|partition size
    read 'size' bytes starting at offset 'off'
    to/from memory address 'addr', skipping bad blocks.
store write name addr off|partition size
    write 'size' bytes starting at offset 'off'
    to/from memory address 'addr', skipping bad blocks.
store rom_write add off size.
        write uboot to the boot device
store erase boot/data:
        erase the area which is uboot or data
store erase partition <partition_name>:
        erase the area which partition in u-boot
store erase dtb
store erase key
store disprotect key
store rom_protect on/off
store scrub off|partition size
        scrub the area from offset and size
store dtb iread/read/write addr <size>
        read/write dtb, size is optional
store key read/write addr <size>
        read/write key, size is optional
store mbr addr
   update mbr/partition table by dtb

No ethernet found.

resetting ...
GXL:BL1:9ac50e:bb16dc;FEAT:ADFD318C:0OC:3;RCY:0;EMMC:800;NAND:0;READ:0;0.0;CHK:0;
TE: 23698

BL2 Built : 14:48:45, Sep 26 2018.
gxl g6d68897 - yao.zhang@droid07

Board ID = 8, adc=616
set vcck to 1070 mv
set vddee to 1070 mv
CPU clk: 1200MHz
LPower:
DDR3 chl: Rank0+1 @ 792MHz - FAIL
DDR3 chl: Rank0 @ 792MHz
bist_test rank: 0 22 00 45 3a 18 5d 1f 00 3f 40 1f 62 1f 00 3f 40 20 61 1d 00 3a 40 20 61 618   -  PASS

Rank0: 1024MB(auto)-2T-11
ssc: ppm1000-
AddrBus test pass!
NAND init
Load fip header from NAND, src: 0x0000c000, des:0x01400000, size: 0x00004000
New fip structure!
Load bl30 from NAND, src: 0x00010000, des: 0x013c0000, size: 0x00007600
Load bl301 from NAND, src: 0x00018000, des: 0x01380000, size: 0x00002800
Load bl31 from NAND, src: 0x0001c000, des: 0x10100000, size: 0x00019600
Load bl33 from NAND, src: 0x00038000, des: 0x01000000, size: 0x00080a00
NOTICE:  BL3-1: v1.0(debug):361f8a7
NOTICE:  BL3-1: Built : 16:43:26, Dec 19 2018
NOTICE:  BL31: GXL normal boot!
NOTICE:  BL31: BL33 decompress pass
[Image: gxl_v1.1.3103-9234004 2018-12-27 10:43:23  yao.zhang@droid07]
efuse init ops = e4
efuse init hdcp = c, cf9=7
x2_hp_e = 0
bl30: check_permit, count is 1
bl30: check_permit: ok!
chipid: 0 0 3 c c 0 53 b4 30 a0 0 e4 not ES chip
[0.611588 Inits done]
INFO:    BL3-1: Initializing runtime services
WARNING: No OPTEE provided by BL2 boot loader
ERROR:   Error initializing runtime service opteed_fast
INFO:    BL3-1: Preparing for EL3 exit to normalworld
INFO:    BL3-1: Next image address = 0x1000000
INFO:    BL3-1: Next image spsr = 0x3c9


U-Boot 2015.01-g53bf894-dirty (Nov 29 2019 - 20:32:00)

DRAM:  1 GiB


我的恩山、我的无线 The best wifi forum is right here.
发表于 2020-4-4 23:40 | 显示全部楼层
WARNING: No OPTEE provided by BL2 boot loader
ERROR:   Error initializing runtime service opteed_fast
没玩过这个,不过看起来是bl加载一些东西失败

点评

还是bootloader没了  详情 回复 发表于 2020-4-4 23:45
是不是U-boot没了?  详情 回复 发表于 2020-4-4 23:43
我的恩山、我的无线 The best wifi forum is right here.
回复

使用道具 举报

 楼主| 发表于 2020-4-4 23:43 | 显示全部楼层
paldier 发表于 2020-4-4 23:40
WARNING: No OPTEE provided by BL2 boot loader
ERROR:   Error initializing runtime service opteed_fa ...

是不是U-boot没了?
我的恩山、我的无线 The best wifi forum is right here.
回复

使用道具 举报

 楼主| 发表于 2020-4-4 23:45 | 显示全部楼层
paldier 发表于 2020-4-4 23:40
WARNING: No OPTEE provided by BL2 boot loader
ERROR:   Error initializing runtime service opteed_fa ...

还是bootloader没了
我的恩山、我的无线 The best wifi forum is right here.
回复

使用道具 举报

 楼主| 发表于 2020-4-9 23:21 来自手机 | 显示全部楼层
顶一下,看有没有朋友能帮到忙
我的恩山、我的无线 The best wifi forum is right here.
回复

使用道具 举报

发表于 2020-4-10 10:05 来自手机 | 显示全部楼层
这盒子只要插usb线能认出来就能强刷,强刷失败问题就比较大了

点评

没有反应了!!  详情 回复 发表于 2020-4-12 23:34
我的恩山、我的无线 The best wifi forum is right here.
回复

使用道具 举报

 楼主| 发表于 2020-4-12 23:34 | 显示全部楼层
wuchenh 发表于 2020-4-10 10:05
这盒子只要插usb线能认出来就能强刷,强刷失败问题就比较大了

没有反应了!!
我的恩山、我的无线 The best wifi forum is right here.
回复

使用道具 举报

发表于 2020-4-12 23:55 来自手机 | 显示全部楼层
按遥探的设置键可设置,楼主想提固件?

点评

不是,是想复活它  详情 回复 发表于 2020-5-1 18:10
我的恩山、我的无线 The best wifi forum is right here.
回复

使用道具 举报

 楼主| 发表于 2020-5-1 18:10 | 显示全部楼层
42669020@qq.com 发表于 2020-4-12 23:55
按遥探的设置键可设置,楼主想提固件?

不是,是想复活它
我的恩山、我的无线 The best wifi forum is right here.
回复

使用道具 举报

发表于 2020-5-1 22:30 来自手机 | 显示全部楼层
可以试试短接强刷

点评

短接后可认了,就是到98%后写入失败  详情 回复 发表于 2020-5-2 02:15
我的恩山、我的无线 The best wifi forum is right here.
回复

使用道具 举报

 楼主| 发表于 2020-5-2 02:15 | 显示全部楼层
wuchenh 发表于 2020-5-1 22:30
可以试试短接强刷

短接后可认了,就是到98%后写入失败

点评

短接哪里?我的是B860AV1.1的,变黑砖了。开机,ttl只会跑4行码,然后停下  详情 回复 发表于 2021-2-22 23:26
线刷工具你用什么版本的?换个老版本试试,2.0几的  详情 回复 发表于 2020-5-2 11:29
我的恩山、我的无线 The best wifi forum is right here.
回复

使用道具 举报

发表于 2020-5-2 11:29 | 显示全部楼层
`wifi` 发表于 2020-5-2 02:15
短接后可认了,就是到98%后写入失败

线刷工具你用什么版本的?换个老版本试试,2.0几的

点评

V2.0.7.2和V2.1.6.8都一样  详情 回复 发表于 2020-5-3 16:40
我的恩山、我的无线 The best wifi forum is right here.
回复

使用道具 举报

 楼主| 发表于 2020-5-3 16:40 | 显示全部楼层
wuchenh 发表于 2020-5-2 11:29
线刷工具你用什么版本的?换个老版本试试,2.0几的

V2.0.7.2和V2.1.6.8都一样
我的恩山、我的无线 The best wifi forum is right here.
回复

使用道具 举报

 楼主| 发表于 2020-5-3 18:48 | 显示全部楼层
每次都是这样,不知道是什么原因

本帖子中包含更多资源

您需要 登录 才可以下载或查看,没有账号?立即注册

×
我的恩山、我的无线 The best wifi forum is right here.
回复

使用道具 举报

发表于 2020-5-3 19:00 | 显示全部楼层
固件包不对啊,1.1t怎么能用2.1a的?只能用2.1的吧

点评

改了好多固件都不行,现在都卡在7%那里!可以要用这个包才可以.没有帐号下不了!  详情 回复 发表于 2020-5-18 12:07
我的恩山、我的无线 The best wifi forum is right here.
回复

使用道具 举报

您需要登录后才可以回帖 登录 | 立即注册

本版积分规则

有疑问请添加管理员QQ86788181|手机版|小黑屋|Archiver|恩山无线论坛(常州市恩山计算机开发有限公司版权所有) ( 苏ICP备05084872号 )

GMT+8, 2024-3-29 03:27

Powered by Discuz! X3.5

© 2001-2024 Discuz! Team.

| 江苏省互联网有害信息举报中心 举报信箱:js12377 | @jischina.com.cn 举报电话:025-88802724 本站不良内容举报信箱:68610888@qq.com 举报电话:0519-86695797

快速回复 返回顶部 返回列表