找回密码
 立即注册

QQ登录

只需一步,快速开始

搜索
广告投放联系QQ68610888
查看: 23859|回复: 25

歌华链 Gehua-GH-A1路由的TTL口

[复制链接]
发表于 2018-12-27 09:24 | 显示全部楼层 |阅读模式
本帖最后由 jzhou404 于 2018-12-27 09:26 编辑

坑爹的是板子上标注像是TTL的端口, 是没信号输出的。

正确的TTL口见附件图(借用了一张网友的图, 见谅)。
通过TTL, 中断BOOT,选择TFTP同样可以刷入BREED

网口向上

J4 从左到右是

GND---TX---RX

设为57600, 8N1, NONE,NONE











本帖子中包含更多资源

您需要 登录 才可以下载或查看,没有账号?立即注册

×
我的恩山、我的无线 The best wifi forum is right here.
发表于 2018-12-27 09:43 | 显示全部楼层
感谢楼主分享,
请问是否有保留TTL输出? 想要一份看看,谢谢!
我的恩山、我的无线 The best wifi forum is right here.
回复

使用道具 举报

发表于 2018-12-27 10:04 | 显示全部楼层
哈哈哈哈难怪我接那边是没有输出的,不过那边可以测出来是gpio好像是7和8
我的恩山、我的无线 The best wifi forum is right here.
回复

使用道具 举报

发表于 2018-12-27 10:06 | 显示全部楼层
右边那个ttl我焊上去了,breed的启动信息还是可以看到的。。。
我的恩山、我的无线 The best wifi forum is right here.
回复

使用道具 举报

发表于 2018-12-27 11:28 | 显示全部楼层
插串口会无法开机 必须先通电再插串口线

点评

真的是这样吗? 我的好像先插电也没反映,可能焊的有问题吧  详情 回复 发表于 2019-3-31 22:24
我的恩山、我的无线 The best wifi forum is right here.
回复

使用道具 举报

发表于 2018-12-27 12:06 | 显示全部楼层
我说呢   连上没反应

我的恩山、我的无线 The best wifi forum is right here.
回复

使用道具 举报

发表于 2018-12-27 12:35 来自手机 | 显示全部楼层
所以说,应该刷pbr m1的breed才是对的?57600才是正确的

点评

目前确实只有m1的breed可以启动各种固件。。。波特率可以在breed里手动更改成115200。。。  详情 回复 发表于 2018-12-27 12:48
我的恩山、我的无线 The best wifi forum is right here.
回复

使用道具 举报

发表于 2018-12-27 12:48 | 显示全部楼层
kochiya 发表于 2018-12-27 12:35
所以说,应该刷pbr m1的breed才是对的?57600才是正确的

目前确实只有m1的breed可以启动各种固件。。。波特率可以在breed里手动更改成115200。。。
我的恩山、我的无线 The best wifi forum is right here.
回复

使用道具 举报

发表于 2018-12-27 19:55 | 显示全部楼层
牛逼,终于找到了
我的恩山、我的无线 The best wifi forum is right here.
回复

使用道具 举报

发表于 2018-12-28 15:00 来自手机 | 显示全部楼层
不小心升到1.26了,这个方法还在试,好像不行,求助各位大大
我的恩山、我的无线 The best wifi forum is right here.
回复

使用道具 举报

发表于 2018-12-28 16:04 | 显示全部楼层
我的1.26固件用ttl能连上,不知道怎么刷.

点评

另外 能不能给一份完整的 ttl 输出,从系统通电开始记录。 谢谢!  详情 回复 发表于 2018-12-29 13:36
我的恩山、我的无线 The best wifi forum is right here.
回复

使用道具 举报

发表于 2018-12-28 21:05 | 显示全部楼层
silver08 发表于 2018-12-28 16:04
我的1.26固件用ttl能连上,不知道怎么刷.

你能连上是怎么判断的?
我的恩山、我的无线 The best wifi forum is right here.
回复

使用道具 举报

发表于 2018-12-29 12:42 | 显示全部楼层
BusyBox v1.22.1 (2018-12-20 12:58:47 CST) built-in shell (ash)
Enter 'help' for a list of built-in commands.

  _______                     ________        __
|       |.-----.-----.-----.|  |  |  |.----.|  |_
|   -   ||  _  |  -__|     ||  |  |  ||   _||   _|
|_______||   __|_____|__|__||________||__|  |____|
          |__| W I R E L E S S   F R E E D O M
-----------------------------------------------------
BARRIER BREAKER (1.26, unknown)
-----------------------------------------------------
  * 1/2 oz Galliano         Pour all ingredients into
  * 4 oz cold Coffee        an irish coffee mug filled
  * 1 1/2 oz Dark Rum       with crushed ice. Stir.
  * 2 tsp. Creme de Cacao
-----------------------------------------------------
MTK OpenWrt SDK V3.4
1443366e
benchmark : APSoC SDK 5.0.1.0
kernel : 169495
-----------------------------------------------------
root@OpenWrt:/# ls
bin      etc      lib      overlay  rom      sbin     tmp      var
dev      etc_ro   mnt      proc     root     sys      usr      www
root@OpenWrt:/# cd mnt
root@OpenWrt:/mnt# ls
sda1
root@OpenWrt:/mnt# cd sda1
root@OpenWrt:/mnt/sda1# ls
breed.bin
root@OpenWrt:/mnt/sda1# cat /proc/mtd
dev:    size   erasesize  name
mtd0: 02000000 00010000 "ALL"
mtd1: 00030000 00010000 "Bootloader"
mtd2: 00010000 00010000 "Config"
mtd3: 00010000 00010000 "Factory"
mtd4: 01fb0000 00010000 "firmware"
mtd5: 01e1c47c 00010000 "rootfs"
mtd6: 01350000 00010000 "rootfs_data"
root@OpenWrt:/mnt/sda1# mtd write breed.bin Bootloader
Could not open mtd device: Bootloader
Can't open device for writing!
root@OpenWrt:/mnt/sda1#


Bootloader锁了,我用U盘写不进去

点评

试试先MTD unlock一下? 我是开机, 好像是选择了9最后一个(记不清了, 你自己看看), 用TFTP刷bootload那个选项的, 一点问题都没有  详情 回复 发表于 2018-12-31 08:22
试试 sysupgrade firmware1.21.bin  详情 回复 发表于 2018-12-29 13:33
我的恩山、我的无线 The best wifi forum is right here.
回复

使用道具 举报

发表于 2018-12-29 13:33 | 显示全部楼层
silver08 发表于 2018-12-29 12:42
Bootloader锁了,我用U盘写不进去

试试 sysupgrade firmware1.21.bin
我的恩山、我的无线 The best wifi forum is right here.
回复

使用道具 举报

发表于 2018-12-29 13:36 | 显示全部楼层
silver08 发表于 2018-12-28 16:04
我的1.26固件用ttl能连上,不知道怎么刷.

另外 能不能给一份完整的 ttl 输出,从系统通电开始记录。
谢谢!

点评

这个是从通电到系统加载完的  详情 回复 发表于 2018-12-29 13:56
我的恩山、我的无线 The best wifi forum is right here.
回复

使用道具 举报

您需要登录后才可以回帖 登录 | 立即注册

本版积分规则

有疑问请添加管理员QQ86788181|手机版|小黑屋|Archiver|恩山无线论坛(常州市恩山计算机开发有限公司版权所有) ( 苏ICP备05084872号 )

GMT+8, 2024-4-19 22:33

Powered by Discuz! X3.5

© 2001-2024 Discuz! Team.

| 江苏省互联网有害信息举报中心 举报信箱:js12377 | @jischina.com.cn 举报电话:025-88802724 本站不良内容举报信箱:68610888@qq.com 举报电话:0519-86695797

快速回复 返回顶部 返回列表