小白求助大神T1刷机提示成功，但开机卡在斐讯白屏界面。

taczgk

请大神帮帮忙，我的斐讯T1盒子原来用的YYF系统，刷了W大3.0和3.5系统都是开机卡在斐讯界面，刷YYF系统就卡在安卓机器人界面，打勾救砖模式都提示错误：[0x00101004]擦除bootloader/USB限流/设备识别/命令结果返回错误，
不打勾的话，刷机提示刷机成功，电脑也可以识别，刷完就卡在开机界面，无法联网无法ADB,求大神指点，谢谢。打勾救砖模式每次都是下边这些错误代码。拆机短接   再打勾刷机救砖可以成功，TTL模式下更新bootloader ,recovety，boot,在输入update,也能刷机成功，但是刷完重启还是卡在斐讯白屏界面。
现在不管怎么刷都能成功，TTL信息都是报错卡屏，无语了。。。
GXM:BL1:dc8b51:76f1a5;FEAT:BDFD31BC:80OC:3;RCY:0;EMMC:0;READ:0;0.0;CHK:0;
TE: 401217

BL2 Built : 11:58:42, May 27 2017.
gxl gc3c9a84 - xiaobo.gu@droid05

set vdd cpu_a to 1120 mv
set vdd cpu_b to 1050 mv
set vddee to 1000 mv
Board ID = 4
CPU clk: 1200MHz
DQS-corr enabled
DDR scramble enabled
DDR3 chl: Rank0+1 @ 912MHz
Rank0: 1024MB-2T-13
Rank1: 1024MB-2T-13
DataBus test pass!
AddrBus test pass!
-s
Load fip header from eMMC, src: 0x0000c200, des: 0x01400000, size: 0x00004000
aml log : R2048 check pass!
New fip structure!
Load bl30 from eMMC, src: 0x00010200, des: 0x01700000, size: 0x0000d600
aml log : R2048 check pass!
Load bl31 from eMMC, src: 0x00020200, des: 0x01700000, size: 0x0002c600
aml log : R2048 check pass!
Load bl33 from eMMC, src: 0x00050200, des: 0x01700000, size: 0x00065400
aml log : R2048 check pass!
NOTICE:  BL3-1: v1.0(release):a625749
NOTICE:  BL3-1: Built : 11:25:15, Aug 25 2017
NOTICE:  BL31: BL33 decompress pass
mpu_config_enablek
[Image: gxl_v1.1.3243-377db0f 2017-09-07 11:28:58 qiufang.dai@droid07]
OPS=0x82
wdt: reset registers!
89 3a 73 2e 6c 83 1 e9 81 5b 94 27 [1.059429 Inits done]
secure task start!
high task start!
low task start!
ERROR:   Error initializing runtime service opteed_fast


U-Boot 2015.01-dirty (Dec 22 2017 - 10:20:14)

DRAM:  2 GiB
Relocation Offset is: 76eb8000
register usb cfg[0][1] = 0000000077f5b690
[CANVAS]canvas init
vpu: error: vpu: check dts: FDT_ERR_BADMAGIC, load default parameters
vpu: clk_level = 7
vpu: set clk: 666667000Hz, readback: 666660000Hz(0x300)
vpu: vpu_clk_gate_init_off
vpp: vpp_init
boot_device_flag : 1
Nand PHY Ver:1.01.001.0006 (c) 2013 Amlogic Inc.
init bus_cycle=6, bus_timing=7, system=5.0ns
reset failed
get_chip_type and ret:fffffffe
get_chip_type and ret:fffffffe
chip detect failed and ret:fffffffe
nandphy_init failed and ret=0xfffffff1
MMC:   aml_priv->desc_buf = 0x0000000073eb86b0
aml_priv->desc_buf = 0x0000000073eba9d0
SDIO Port B: 0, SDIO Port C: 1
emmc/sd response timeout, cmd8, status=0x1ff2800
emmc/sd response timeout, cmd55, status=0x1ff2800
init_part() 293: PART_TYPE_AML
[mmc_init] mmc init success
dtb magic 71b104da
aml log : R2048 check pass!
      Amlogic multi-dtb tool
      Single dtb detected
start dts,buffer=0000000073ebd200,dt_addr=0000000073ebd200
      Amlogic multi-dtb tool
      Single dtb detected
parts: 10
00:      logo   0000000002000000 1
01:  recovery   0000000002000000 1
02:       rsv   0000000000800000 1
03:       tee   0000000000800000 1
04:     crypt   0000000002000000 1
05:      misc   0000000002000000 1
06:      boot   0000000002000000 1
07:    system   0000000080000000 1
08:     cache   0000000020000000 2
09:      data   ffffffffffffffff 4
init_part() 293: PART_TYPE_AML
eMMC/TSD partition table have been checked OK!
check pattern success
mmc env offset: 0x27400000
In:    serial
Out:   serial
Err:   serial
reboot_mode=cold_boot
hpd_state=0
cvbs performance type = 6, table = 0
[store]To run cmd[emmc dtb_read 0x1000000 0x40000]
_verify_dtb_checksum()-917: calc 983f4d19, store 983f4d19
_verify_dtb_checksum()-917: calc 983f4d19, store 983f4d19
dtb_read()-1039: total valid 2
dtb_read()-1106: do nothing
aml log : R2048 check pass!
      Amlogic multi-dtb tool
      Single dtb detected
vpp: vpp_pq_load pq val error !!!
Net:   dwmac.c9410000amlkey_init() enter!
[EFUSE_MSG]keynum is 1
[BL31]: tee size: 0

Start read misc partition datas!
info->attemp_times = 0
info->active_slot = 0
info->slot_info[0].bootable = 1
info->slot_info[0].online = 1
info->slot_info[1].bootable = 0
info->slot_info[1].online = 0
info->attemp_times = 0
attemp_times = 0
active slot = 0
wipe_data=successful
wipe_cache=successful
upgrade_step=2
[OSD]load fb addr from dts
[OSD]fb_addr for logo: 0x7f851000
[OSD]load fb addr from dts
[OSD]fb_addr for logo: 0x7f851000
[CANVAS]addr=0x7f851000 width=3840, height=2160
amlkey_init() enter!
amlkey_init() 71: already init!
[EFUSE_MSG]keynum is 1
[BL31]: tee size: 0
[BL31]: tee size: 0
[BL31]: tee size: 0
[BL31]: tee size: 0
[BL31]: tee size: 0
[KM]Error:f[key_manage_query_size]L507:key[mac] not programed yet
[KM]Error:f[key_manage_query_size]L507:key[deviceid] not programed yet
[KM]Error:f[key_manage_query_size]L507:key[mac_wifi] not programed yet
gpio: pin GPIOAO_2 (gpio 102) value is 1
InUsbBurn
noSof
Hit Enter or space or Ctrl+C key to stop autoboot -- :  0
[imgread]szTimeStamp[2018032717003412]
[imgread]secureKernelImgSz=0x983800
aml log : R-2048 check pass!
aml log : R2048 check pass!
aml log : R2048 check pass!
ee_gate_off ...
mmc env offset: 0x27400000
Writing to MMC(1)... done
## Booting Android Image at 0x01080000 ...
reloc_addr =73f3d3b0
copy done
Kernel command line: buildvariant=user
load dtb from 0x1000000 ......
      Amlogic multi-dtb tool
      Single dtb detected
   Uncompressing Kernel Image ... OK
   kernel loaded at 0x01080000, end = 0x021d0558
   Loading Ramdisk to 73d36000, end 73ea6000 ... OK
   Loading Device Tree to 000000001fff1000, end 000000001ffff1cd ... OK
fdt_instaboot: no instaboot image

Starting kernel ...

uboot time: 3645140 us
[    0.000000@0] Initializing cgroup subsys cpu
[    0.000000@0] Initializing cgroup subsys cpuacct
[    0.000000@0] Linux version 3.14.29-00001-g71ca4b4 (jenkins@slave2) (gcc version 4.9.3 (Ubuntu/Linaro 4.9.3-13ubuntu2) ) #1 SMP PREEMPT Tue Mar 27 16:25:39 CST 2018
[    0.000000@0] CPU: AArch64 Processor [410fd034] revision 4
[    0.000000@0] no prop version_code
[    0.000000@0] bootconsole [earlycon0] enabled
[    0.000000@0] Reserved memory: incorrect alignment of CMA region
[    0.000000@0] [amvecm] pq string error !!!
[    0.279603@3] genirq: Setting trigger mode 8 for irq 241 failed (gic_set_type+0x0/0xbc)
[    0.282085@3] genirq: Setting trigger mode 8 for irq 242 failed (gic_set_type+0x0/0xbc)
[    0.290343@3] genirq: Setting trigger mode 8 for irq 241 failed (gic_set_type+0x0/0xbc)
[    0.298185@3] genirq: Setting trigger mode 8 for irq 242 failed (gic_set_type+0x0/0xbc)
domain-0 init dvfs: 4
domain-1 init dvfs: 4
[    0.323283@2] tv_vout: chrdev devno 266338304 for disp
[    0.337950@2] 1507 node need 400ms
[    0.828432@0] Initramfs unpacking failed: junk in compressed archive
[    0.911626@1] mtdoops: mtd device (mtddev=name/number) must be supplied
[    0.922614@2] amlogic-new-usb3 d0078080.usb3phy: This phy has no usb port
[    0.932881@3] ATVR driver - init called!
[    0.937488@3] meson-gpu-clkgen c883c000.gpu_clk: can't request region for resource [mem 0xc883c000-0xc883cfff]
[    0.944919@3] get_storage_dev return 1
[    1.094494@1] fb: failed to init reserved memory
[    1.113109@0] pwmled: conflict with jtag apao
[    1.123602@0] DI-di_probe: get flag_cma error.
[    1.125578@1] PPMGRDRV: err: ppmgr_driver_probe called
efuse_pw_en: 0x7
WARNING! efuse bits is disabled
Enable A53 JTAG cluster 0 to AO
[    1.155545@2] cectx aocec: no hdmirx reg resource
[    1.155573@2] cectx aocec: no hhi reg resource
[    1.381050@2] aml_snd_m8_card aml_m8_snd.50: ASoC: no source widget found for LOUTL
[    1.383053@2] aml_snd_m8_card aml_m8_snd.50: ASoC: Failed to add route LOUTL -> direct -> Ext Spk
[    1.391896@2] aml_snd_m8_card aml_m8_snd.50: ASoC: no source widget found for LOUTR
[    1.399444@2] aml_snd_m8_card aml_m8_snd.50: ASoC: Failed to add route LOUTR -> direct -> Ext Spk
[    1.420332@3] Bluetooth: Can't register RFCOMM TTY driver
[    [    1.815822@3] init: waitpid failed: No child processes
[    1.818849@3] init: ignored duplicate definition of service 'adbd'init: (Parsing /init.usb.rc took 0.00s.)
[    1.825735@3] init: /init.amlogic.rc: 276: chmod requires 2 arguments
[    1.834641@3] init: aml-firstboot-init insert aml-firstboot-init
[    1.940931@3] init: insmod: open("/boot/optee.ko") failed: No such file or directory
[    1.942893@3] init: insmod: open("/boot/optee_armtz.ko") failed: No such file or directory[    2.264490@3] ueventd: Cannot set 'ubject_rwntty_device:[    2.270595@3] ueventd: Cannot set 'ubject_r:ptmx_device:s0' SELinux label on '/dev/ptmx' device (Permission denied)
[    2.283697@3] ueventd: Cannot set 'ubject_r:console_device:s0' SELinux label on '/dev/console' device (Permission denied)
[    2.842528@3] init: enter do_confirm_formated /dev/block/tee, /tee
[    2.843088@3] init: blocksize 1024, bytes_per_inode 1024
[    2.848329@3] init: do_confirm_formated ext4 try mount
[    2.930602@7] init: enter do_confirm_formated /dev/block/data, /data
[    2.931334@7] init: do_confirm_formated ext4 try mount
[    2.980306@7] init: enter do_confirm_formated /dev/block/cache, /cache
[    2.981211@7] init: do_confirm_formated ext4 try mount
[    3.074878@2] accelerate:
[    3.074878@2] kernel start with quiet!

hbwwm

第一次启动时间较长，多等会儿。

taczgk

hbwwm 发表于 2020-5-18 15:22
第一次启动时间较长，多等会儿。

等了半个小时还是那个界面，应该是卡住了。

tayo56

重新再次刷机

taczgk

tayo56 发表于 2020-5-18 15:33
重新再次刷机

换了三个固件都不行，刷了好几遍了都是卡在开机界面，也不能救砖模式。

hbwwm

刷 Rush 精简版试试：https://www.right.com.cn/forum/thread-315889-1-1.html

kent_xyli

是不是因为密钥没有选中打勾

taczgk

kent_xyli 发表于 2020-5-20 14:26
是不是因为密钥没有选中打勾

打勾不打勾都试了  一样的错误，盼着出个新错误也行啊

taczgk

hbwwm 发表于 2020-5-18 19:46
刷 Rush 精简版试试：https://www.right.com.cn/forum/thread-315889-1-1.html

谢谢大神关注，不打勾擦除直接刷都能成功，刷完再启动就卡在第一屏了。打勾擦除6秒就提示错误。

deeair

有偿 20 加Q46166058

deeair

46166058  帮你搞

huofeng26

楼主的盒子修好了吗？我的也是这样的问题，实在是没办法了，求解决方法。

297118122

huofeng26 发表于 2020-8-8 00:21
楼主的盒子修好了吗？我的也是这样的问题，实在是没办法了，求解决方法。

只选搽除flash试试

huofeng26

297118122 发表于 2020-8-8 01:42
只选搽除flash试试

又试了一遍 还是不行，开机闪一下开机画面就黑屏了。

taczgk

我的一直卡在开机画面,刷机能提示成功,每个版本都试过了还是不行,估计内存挂了.