请教各位大神斐讯T1刷机成功卡在斐讯白屏界面如何解决谢谢

taczgk

请大神帮帮忙，我的斐讯T1盒子原来用的YYF系统，刷机重启后都是卡在开机界面，等半小时也不动。不打勾擦除的话，常规刷机提示刷机成功，电脑也可以识别；
打勾擦除，救砖模式刷机提示错误：[0x00101004]擦除bootloader/USB限流/设备识别/命令结果返回错误，
短接触点强制刷机，打勾擦除，救砖模式不提示错误，提示刷机成功；
但是刷机成功后，依然卡在开机界面，无法联网也无法ADB，电脑、固件、刷机线都换过了，
TTL刷机也试了，刷机过程都正常，重启后依然卡屏。求大神指点，谢谢。
TTL信息如下。
GXM:BL1:dc8b51:76f1a5;FEAT:BDFD31BC:80OC:3;RCY:0;EMMC:0;READ:0;0.0;CHK:0;
TE: 401217

BL2 Built : 11:58:42, May 27 2017.
gxl gc3c9a84 - xiaobo.gu@droid05

set vdd cpu_a to 1120 mv
set vdd cpu_b to 1050 mv
set vddee to 1000 mv
Board ID = 4
CPU clk: 1200MHz
DQS-corr enabled
DDR scramble enabled
DDR3 chl: Rank0+1 @ 912MHz
Rank0: 1024MB-2T-13
Rank1: 1024MB-2T-13
DataBus test pass!
AddrBus test pass!
-s
Load fip header from eMMC, src: 0x0000c200, des: 0x01400000, size: 0x00004000
aml log : R2048 check pass!
New fip structure!
Load bl30 from eMMC, src: 0x00010200, des: 0x01700000, size: 0x0000d600
aml log : R2048 check pass!
Load bl31 from eMMC, src: 0x00020200, des: 0x01700000, size: 0x0002c600
aml log : R2048 check pass!
Load bl33 from eMMC, src: 0x00050200, des: 0x01700000, size: 0x00065400
aml log : R2048 check pass!
NOTICE:  BL3-1: v1.0(release):a625749
NOTICE:  BL3-1: Built : 11:25:15, Aug 25 2017
NOTICE:  BL31: BL33 decompress pass
mpu_config_enablek
[Image: gxl_v1.1.3243-377db0f 2017-09-07 11:28:58 qiufang.dai@droid07]
OPS=0x82
wdt: reset registers!
89 3a 73 2e 6c 83 1 e9 81 5b 94 27 [1.059429 Inits done]
secure task start!
high task start!
low task start!
ERROR:   Error initializing runtime service opteed_fast


U-Boot 2015.01-dirty (Dec 22 2017 - 10:20:14)

DRAM:  2 GiB
Relocation Offset is: 76eb8000
register usb cfg[0][1] = 0000000077f5b690
[CANVAS]canvas init
vpu: error: vpu: check dts: FDT_ERR_BADMAGIC, load default parameters
vpu: clk_level = 7
vpu: set clk: 666667000Hz, readback: 666660000Hz(0x300)
vpu: vpu_clk_gate_init_off
vpp: vpp_init
boot_device_flag : 1
Nand PHY Ver:1.01.001.0006 (c) 2013 Amlogic Inc.
init bus_cycle=6, bus_timing=7, system=5.0ns
reset failed
get_chip_type and ret:fffffffe
get_chip_type and ret:fffffffe
chip detect failed and ret:fffffffe
nandphy_init failed and ret=0xfffffff1
MMC:   aml_priv->desc_buf = 0x0000000073eb86b0
aml_priv->desc_buf = 0x0000000073eba9d0
SDIO Port B: 0, SDIO Port C: 1
emmc/sd response timeout, cmd8, status=0x1ff2800
emmc/sd response timeout, cmd55, status=0x1ff2800
init_part() 293: PART_TYPE_AML
[mmc_init] mmc init success
dtb magic 71b104da
aml log : R2048 check pass!
      Amlogic multi-dtb tool
      Single dtb detected
start dts,buffer=0000000073ebd200,dt_addr=0000000073ebd200
      Amlogic multi-dtb tool
      Single dtb detected
parts: 10
00:      logo   0000000002000000 1
01:  recovery   0000000002000000 1
02:       rsv   0000000000800000 1
03:       tee   0000000000800000 1
04:     crypt   0000000002000000 1
05:      misc   0000000002000000 1
06:      boot   0000000002000000 1
07:    system   0000000080000000 1
08:     cache   0000000020000000 2
09:      data   ffffffffffffffff 4
init_part() 293: PART_TYPE_AML
eMMC/TSD partition table have been checked OK!
check pattern success
mmc env offset: 0x27400000
In:    serial
Out:   serial
Err:   serial
reboot_mode=cold_boot
hpd_state=0
cvbs performance type = 6, table = 0
[store]To run cmd[emmc dtb_read 0x1000000 0x40000]
_verify_dtb_checksum()-917: calc 983f4d19, store 983f4d19
_verify_dtb_checksum()-917: calc 983f4d19, store 983f4d19
dtb_read()-1039: total valid 2
dtb_read()-1106: do nothing
aml log : R2048 check pass!
      Amlogic multi-dtb tool
      Single dtb detected
vpp: vpp_pq_load pq val error !!!
Net:   dwmac.c9410000amlkey_init() enter!
[EFUSE_MSG]keynum is 1
[BL31]: tee size: 0

Start read misc partition datas!
info->attemp_times = 0
info->active_slot = 0
info->slot_info[0].bootable = 1
info->slot_info[0].online = 1
info->slot_info[1].bootable = 0
info->slot_info[1].online = 0
info->attemp_times = 0
attemp_times = 0
active slot = 0
wipe_data=successful
wipe_cache=successful
upgrade_step=2
[OSD]load fb addr from dts
[OSD]fb_addr for logo: 0x7f851000
[OSD]load fb addr from dts
[OSD]fb_addr for logo: 0x7f851000
[CANVAS]addr=0x7f851000 width=3840, height=2160
amlkey_init() enter!
amlkey_init() 71: already init!
[EFUSE_MSG]keynum is 1
[BL31]: tee size: 0
[BL31]: tee size: 0
[BL31]: tee size: 0
[BL31]: tee size: 0
[BL31]: tee size: 0
[KM]Error:f[key_manage_query_size]L507:key[mac] not programed yet
[KM]Error:f[key_manage_query_size]L507:key[deviceid] not programed yet
[KM]Error:f[key_manage_query_size]L507:key[mac_wifi] not programed yet
gpio: pin GPIOAO_2 (gpio 102) value is 1
InUsbBurn
noSof
Hit Enter or space or Ctrl+C key to stop autoboot -- :  0
[imgread]szTimeStamp[2018032717003412]
[imgread]secureKernelImgSz=0x983800
aml log : R-2048 check pass!
aml log : R2048 check pass!
aml log : R2048 check pass!
ee_gate_off ...
mmc env offset: 0x27400000
Writing to MMC(1)... done
## Booting Android Image at 0x01080000 ...
reloc_addr =73f3d3b0
copy done
Kernel command line: buildvariant=user
load dtb from 0x1000000 ......
      Amlogic multi-dtb tool
      Single dtb detected
   Uncompressing Kernel Image ... OK
   kernel loaded at 0x01080000, end = 0x021d0558
   Loading Ramdisk to 73d36000, end 73ea6000 ... OK
   Loading Device Tree to 000000001fff1000, end 000000001ffff1cd ... OK
fdt_instaboot: no instaboot image

Starting kernel ...

uboot time: 3645140 us
[    0.000000@0] Initializing cgroup subsys cpu
[    0.000000@0] Initializing cgroup subsys cpuacct
[    0.000000@0] Linux version 3.14.29-00001-g71ca4b4 (jenkins@slave2) (gcc version 4.9.3 (Ubuntu/Linaro 4.9.3-13ubuntu2) ) #1 SMP PREEMPT Tue Mar 27 16:25:39 CST 2018
[    0.000000@0] CPU: AArch64 Processor [410fd034] revision 4
[    0.000000@0] no prop version_code
[    0.000000@0] bootconsole [earlycon0] enabled
[    0.000000@0] Reserved memory: incorrect alignment of CMA region
[    0.000000@0] [amvecm] pq string error !!!
[    0.279603@3] genirq: Setting trigger mode 8 for irq 241 failed (gic_set_type+0x0/0xbc)
[    0.282085@3] genirq: Setting trigger mode 8 for irq 242 failed (gic_set_type+0x0/0xbc)
[    0.290343@3] genirq: Setting trigger mode 8 for irq 241 failed (gic_set_type+0x0/0xbc)
[    0.298185@3] genirq: Setting trigger mode 8 for irq 242 failed (gic_set_type+0x0/0xbc)
domain-0 init dvfs: 4
domain-1 init dvfs: 4
[    0.323283@2] tv_vout: chrdev devno 266338304 for disp
[    0.337950@2] 1507 node need 400ms
[    0.828432@0] Initramfs unpacking failed: junk in compressed archive
[    0.911626@1] mtdoops: mtd device (mtddev=name/number) must be supplied
[    0.922614@2] amlogic-new-usb3 d0078080.usb3phy: This phy has no usb port
[    0.932881@3] ATVR driver - init called!
[    0.937488@3] meson-gpu-clkgen c883c000.gpu_clk: can't request region for resource [mem 0xc883c000-0xc883cfff]
[    0.944919@3] get_storage_dev return 1
[    1.094494@1] fb: failed to init reserved memory
[    1.113109@0] pwmled: conflict with jtag apao
[    1.123602@0] DI-di_probe: get flag_cma error.
[    1.125578@1] PPMGRDRV: err: ppmgr_driver_probe called
efuse_pw_en: 0x7
WARNING! efuse bits is disabled
Enable A53 JTAG cluster 0 to AO
[    1.155545@2] cectx aocec: no hdmirx reg resource
[    1.155573@2] cectx aocec: no hhi reg resource
[    1.381050@2] aml_snd_m8_card aml_m8_snd.50: ASoC: no source widget found for LOUTL
[    1.383053@2] aml_snd_m8_card aml_m8_snd.50: ASoC: Failed to add route LOUTL -> direct -> Ext Spk
[    1.391896@2] aml_snd_m8_card aml_m8_snd.50: ASoC: no source widget found for LOUTR
[    1.399444@2] aml_snd_m8_card aml_m8_snd.50: ASoC: Failed to add route LOUTR -> direct -> Ext Spk
[    1.420332@3] Bluetooth: Can't register RFCOMM TTY driver
[    [    1.815822@3] init: waitpid failed: No child processes
[    1.818849@3] init: ignored duplicate definition of service 'adbd'init: (Parsing /init.usb.rc took 0.00s.)
[    1.825735@3] init: /init.amlogic.rc: 276: chmod requires 2 arguments
[    1.834641@3] init: aml-firstboot-init insert aml-firstboot-init
[    1.940931@3] init: insmod: open("/boot/optee.ko") failed: No such file or directory
[    1.942893@3] init: insmod: open("/boot/optee_armtz.ko") failed: No such file or directory[    2.264490@3] ueventd: Cannot set 'ubject_rwntty_device:[    2.270595@3] ueventd: Cannot set 'ubject_r:ptmx_device:s0' SELinux label on '/dev/ptmx' device (Permission denied)
[    2.283697@3] ueventd: Cannot set 'ubject_r:console_device:s0' SELinux label on '/dev/console' device (Permission denied)
[    2.842528@3] init: enter do_confirm_formated /dev/block/tee, /tee
[    2.843088@3] init: blocksize 1024, bytes_per_inode 1024
[    2.848329@3] init: do_confirm_formated ext4 try mount
[    2.930602@7] init: enter do_confirm_formated /dev/block/data, /data
[    2.931334@7] init: do_confirm_formated ext4 try mount
[    2.980306@7] init: enter do_confirm_formated /dev/block/cache, /cache
[    2.981211@7] init: do_confirm_formated ext4 try mount
[    3.074878@2] accelerate:
[    3.074878@2] kernel start with quiet!


重启有时候这样：

GXM:BL1:dc8b51:76f1a5;FEAT:BDFD31BC:80OC:3;RCY:0;EMMC:0;READ:0;0.0;CHK:0;
TE: 341340

BL2 Built : 11:58:42, May 27 2017.
gxl gc3c9a84 - xiaobo.gu@droid05

set vdd cpu_a to 1120 mv
set vdd cpu_b to 1050 mv
set vddee to 1000 mv
Board ID = 4
CPU clk: 1200MHz
DQS-corr enabled
DDR scramble enabled
DDR3 chl: Rank0+1 @ 912MHz
Rank0: 1024MB-2T-13
Rank1: 1024MB-2T-13
DataBus test pass!
AddrBus test pass!
-s
Load fip header from eMMC, src: 0x0000c200, des: 0x01400000, size: 0x00004000
aml log : R2048 check pass!
New fip structure!
Load bl30 from eMMC, src: 0x00010200, des: 0x01700000, size: 0x0000d600
aml log : R2048 check pass!
Load bl31 from eMMC, src: 0x00020200, des: 0x01700000, size: 0x0002c600
aml log : R2048 check pass!
Load bl33 from eMMC, src: 0x00050200, des: 0x01700000, size: 0x00065400
aml log : R2048 check pass!
NOTICE:  BL3-1: v1.0(release):a625749
NOTICE:  BL3-1: Built : 11:25:15, Aug 25 2017
NOTICE:  BL31: BL33 decompress pass
mpu_config_enablek
[Image: gxl_v1.1.3243-377db0f 2017-09-07 11:28:58 qiufang.dai@droid07]
OPS=0x82
wdt: reset registers!
89 3a 73 2e 6c 83 1 e9 81 5b 94 27 [0.994031 Inits done]
secure task start!
high task start!
low task start!
ERROR:   Error initializing runtime service opteed_fast


U-Boot 2015.01-dirty (Dec 22 2017 - 10:20:14)

DRAM:  2 GiB
Relocation Offset is: 76eb8000
register usb cfg[0][1] = 0000000077f5b690
[CANVAS]canvas init
vpu: error: vpu: check dts: FDT_ERR_BADMAGIC, load default parameters
vpu: clk_level = 7
vpu: set clk: 666667000Hz, readback: 666660000Hz(0x300)
vpu: vpu_clk_gate_init_off
vpp: vpp_init
boot_device_flag : 1
Nand PHY Ver:1.01.001.0006 (c) 2013 Amlogic Inc.
init bus_cycle=6, bus_timing=7, system=5.0ns
reset failed
get_chip_type and ret:fffffffe
get_chip_type and ret:fffffffe
chip detect failed and ret:fffffffe
nandphy_init failed and ret=0xfffffff1
MMC:   aml_priv->desc_buf = 0x0000000073eb86b0
aml_priv->desc_buf = 0x0000000073eba9d0
SDIO Port B: 0, SDIO Port C: 1
emmc/sd response timeout, cmd8, status=0x1ff2800
emmc/sd response timeout, cmd55, status=0x1ff2800
init_part() 293: PART_TYPE_AML
[mmc_init] mmc init success
dtb magic 71b104da
aml log : R2048 check pass!
      Amlogic multi-dtb tool
      Single dtb detected
start dts,buffer=0000000073ebd200,dt_addr=0000000073ebd200
      Amlogic multi-dtb tool
      Single dtb detected
parts: 10
00:      logo   0000000002000000 1
01:  recovery   0000000002000000 1
02:       rsv   0000000000800000 1
03:       tee   0000000000800000 1
04:     crypt   0000000002000000 1
05:      misc   0000000002000000 1
06:      boot   0000000002000000 1
07:    system   0000000080000000 1
08:     cache   0000000020000000 2
09:      data   ffffffffffffffff 4
init_part() 293: PART_TYPE_AML
eMMC/TSD partition table have been checked OK!
check pattern success
mmc env offset: 0x27400000
In:    serial
Out:   serial
Err:   serial
reboot_mode=cold_boot
hpd_state=0
cvbs performance type = 6, table = 0
[store]To run cmd[emmc dtb_read 0x1000000 0x40000]
_verify_dtb_checksum()-917: calc 983f4d19, store 983f4d19
_verify_dtb_checksum()-917: calc 983f4d19, store 983f4d19
dtb_read()-1039: total valid 2
dtb_read()-1106: do nothing
aml log : R2048 check pass!
      Amlogic multi-dtb tool
      Single dtb detected
vpp: vpp_pq_load pq val error !!!
Net:   dwmac.c9410000amlkey_init() enter!
[EFUSE_MSG]keynum is 1
[BL31]: tee size: 0

Start read misc partition datas!
info->attemp_times = 0
info->active_slot = 0
info->slot_info[0].bootable = 1
info->slot_info[0].online = 1
info->slot_info[1].bootable = 0
info->slot_info[1].online = 0
info->attemp_times = 0
attemp_times = 0
active slot = 0
wipe_data=successful
wipe_cache=successful
upgrade_step=2
[OSD]load fb addr from dts
[OSD]fb_addr for logo: 0x7f851000
[OSD]load fb addr from dts
[OSD]fb_addr for logo: 0x7f851000
[CANVAS]addr=0x7f851000 width=3840, height=2160
amlkey_init() enter!
amlkey_init() 71: already init!
[EFUSE_MSG]keynum is 1
[BL31]: tee size: 0
[BL31]: tee size: 0
[BL31]: tee size: 0
[BL31]: tee size: 0
[BL31]: tee size: 0
[KM]Error:f[key_manage_query_size]L507:key[mac] not programed yet
[KM]Error:f[key_manage_query_size]L507:key[deviceid] not programed yet
[KM]Error:f[key_manage_query_size]L507:key[mac_wifi] not programed yet
gpio: pin GPIOAO_2 (gpio 102) value is 1
InUsbBurn
noSof
Hit Enter or space or Ctrl+C key to stop autoboot -- :  0
[imgread]szTimeStamp[2018032717003412]
[imgread]secureKernelImgSz=0x983800
aml log : R-2048 check pass!
aml log : R2048 check pass!
aml log : R2048 check pass!
ee_gate_off ...
mmc env offset: 0x27400000
Writing to MMC(1)... done
## Booting Android Image at 0x01080000 ...
reloc_addr =73f3d3b0
copy done
Kernel command line: buildvariant=user
load dtb from 0x1000000 ......
      Amlogic multi-dtb tool
      Single dtb detected
   Uncompressing Kernel Image ... OK
   kernel loaded at 0x01080000, end = 0x021d0558
   Loading Ramdisk to 73d36000, end 73ea6000 ... OK
   Loading Device Tree to 000000001fff1000, end 000000001ffff1cd ... OK
fdt_instaboot: no instaboot image

Starting kernel ...

uboot time: 3569249 us
[    0.000000@0] Initializing cgroup subsys cpu
[    0.000000@0] Initializing cgroup subsys cpuacct
[    0.000000@0] Linux version 3.14.29-00001-g71ca4b4 (jenkins@slave2) (gcc version 4.9.3 (Ubuntu/Linaro 4.9.3-13ubuntu2) ) #1 SMP PREEMPT Tue Mar 27 16:25:39 CST 2018
[    0.000000@0] CPU: AArch64 Processor [410fd034] revision 4
[    0.000000@0] no prop version_code
[    0.000000@0] bootconsole [earlycon0] enabled
[    0.000000@0] Reserved memory: incorrect alignment of CMA region
[    0.000000@0] [amvecm] pq string error !!!
[    0.279655@3] genirq: Setting trigger mode 8 for irq 241 failed (gic_set_type+0x0/0xbc)
[    0.282136@3] genirq: Setting trigger mode 8 for irq 242 failed (gic_set_type+0x0/0xbc)
[    0.290401@3] genirq: Setting trigger mode 8 for irq 241 failed (gic_set_type+0x0/0xbc)
[    0.298234@3] genirq: Setting trigger mode 8 for irq 242 failed (gic_set_type+0x0/0xbc)
domain-0 init dvfs: 4
domain-1 init dvfs: 4
[    0.323340@2] tv_vout: chrdev devno 266338304 for disp
[    0.338009@2] 1507 node need 400ms
[    0.829556@2] Initramfs unpacking failed: junk in compressed archive
[    0.910794@3] mtdoops: mtd device (mtddev=name/number) must be supplied
[    0.921994@3] amlogic-new-usb3 d0078080.usb3phy: This phy has no usb port
[    0.931473@3] ATVR driver - init called!
[    0.936096@3] meson-gpu-clkgen c883c000.gpu_clk: can't request region for resource [mem 0xc883c000-0xc883cfff]
[    0.943592@3] get_storage_dev return 1
[    1.097113@0] fb: failed to init reserved memory
[    1.102607@1] pwmled: conflict with jtag apao
[    1.115679@0] DI-di_probe: get flag_cma error.
[    1.117704@1] PPMGRDRV: err: ppmgr_driver_probe called
efuse_pw_en: 0x7
WARNING! efuse bits is disabled
Enable A53 JTAG cluster 0 to AO
[    1.149735@0] cectx aocec: no hdmirx reg resource
[    1.149764@0] cectx aocec: no hhi reg resource
[    1.372858@1] aml_snd_m8_card aml_m8_snd.50: ASoC: no source widget found for LOUTL
[    1.374862@1] aml_snd_m8_card aml_m8_snd.50: ASoC: Failed to add route LOUTL -> direct -> Ext Spk
[    1.383677@1] aml_snd_m8_card aml_m8_snd.50: ASoC: no source widget found for LOUTR
[    1.391254@1] aml_snd_m8_card aml_m8_snd.50: ASoC: Failed to add route LOUTR -> direct -> Ext Spk
[    1.409866@0] Bluetooth: Can't register RFCOMM TTY driver
[    [    1.701536@1] Kernel panic - not syncing: Attempted to kill init! exitcode=0x00000004
[    1.701536@1]
[    1.705356@1] CPU: 1 PID: 1 Comm: init Not tainted 3.14.29-00001-g71ca4b4 #1
[    1.712336@1] Call trace:
[    1.714933@1] [<ffffffc001089060>] dump_backtrace+0x0/0x138
[    1.720444@1] [<ffffffc0010891b8>] show_stack+0x20/0x30
[    1.725621@1] [<ffffffc001b229ac>] dump_stack+0x7c/0xc0
[    1.730794@1] [<ffffffc001b1ff54>] panic+0xe8/0x20c
[    1.735625@1] [<ffffffc0010a0a6c>] do_exit+0x9a8/0x9ac
[    1.740713@1] [<ffffffc0010a18c4>] do_group_exit+0x48/0xd4
[    1.746149@1] [<ffffffc0010b1c0c>] get_signal_to_deliver+0x3b8/0x58c
[    1.752443@1] [<ffffffc00108868c>] do_signal+0x270/0x544
[    1.757704@1] [<ffffffc001088b90>] do_notify_resume+0x68/0x74
[    1.763411@0] CPU0: stopping
[    1.766249@0] CPU: 0 PID: 0 Comm: swapper/0 Not tainted 3.14.29-00001-g71ca4b4 #1
[    1.773659@0] Call trace:
[    1.776253@0] [<ffffffc001089060>] dump_backtrace+0x0/0x138
[    1.781768@0] [<ffffffc0010891b8>] show_stack+0x20/0x30
[    1.786943@0] [<ffffffc001b229ac>] dump_stack+0x7c/0xc0
[    1.792119@0] [<ffffffc00108ff3c>] handle_IPI+0x1b8/0x1c8
[    1.797465@0] [<ffffffc00108145c>] gic_handle_irq+0x80/0x88
[    1.802984@0] Exception stack(0xffffffc00209bd60 to 0xffffffc00209be80)
[    1.809542@0] bd60: 7816e058 ffffffc0 00000000 00000000 0209bea0 ffffffc0 016587b0 ffffffc0
[    1.817821@0] bd80: 6744b5af 00000000 6744b5af 00000000 47d563a1 0032a9b5 0003a7e3 00000000
[    1.826101@0] bda0: 00000000 00000000 29aaaaab 00000000 349b0068 00000000 00000018 00000000
[    1.834381@0] bdc0: 020a8060 ffffffc0 ffff8b7d 00000000 00001000 00000000 00000ffb 00000000
[    1.842661@0] bde0: 0000006e 00000000 00000001 00000000 fa83b2da 00000000 01b35f28 ffffffc0
[    1.850941@0] be00: 011bfb64 ffffffc0 00000000 00000000 0000003f 00000000 7816e058 ffffffc0
[    1.859221@0] be20: 00000000 00000000 00000000 00000000 671fd253 00000000 022d3000 ffffffc0
[    1.867501@0] be40: 02135608 ffffffc0 021c3dd5 ffffffc0 00000000 00000000 01080468 ffffffc0
[    1.875781@0] be60: 00000000 00000040 0209bea0 ffffffc0 016587ac ffffffc0 0209bea0 ffffffc0
[    1.884060@0] [<ffffffc001083da0>] el1_irq+0x60/0xd0
[    1.888980@0] [<ffffffc001658904>] cpuidle_idle_call+0xc0/0x24c
[    1.894842@0] [<ffffffc00108552c>] arch_cpu_idle+0x10/0x28
[    1.900277@0] [<ffffffc0010f8c74>] cpu_startup_entry+0x1d0/0x220
[    1.906228@0] [<ffffffc001b1c44c>] rest_init+0x88/0x98
[    1.911318@0] [<ffffffc001f487b0>] start_kernel+0x33c/0x354
[    1.916834@3] CPU3: stopping
[    1.919681@3] CPU: 3 PID: 0 Comm: swapper/3 Not tainted 3.14.29-00001-g71ca4b4 #1
[    1.927097@3] Call trace:
[    1.929687@3] [<ffffffc001089060>] dump_backtrace+0x0/0x138
[    1.935206@3] [<ffffffc0010891b8>] show_stack+0x20/0x30
[    1.940381@3] [<ffffffc001b229ac>] dump_stack+0x7c/0xc0
[    1.945556@3] [<ffffffc00108ff3c>] handle_IPI+0x1b8/0x1c8
[    1.950903@3] [<ffffffc00108145c>] gic_handle_irq+0x80/0x88
[    1.956423@3] Exception stack(0xffffffc0597cfdb0 to 0xffffffc0597cfed0)
[    1.962979@3] fda0:                                     78192058 ffffffc0 00000000 00000000
[    1.971260@3] fdc0: 597cfef0 ffffffc0 016587b0 ffffffc0 6744b5d9 00000000 6744b5d9 00000000
[    1.979540@3] fde0: 71800e4c 0032a9b5 0003a7e4 00000000 00000000 00000000 29aaaaab 00000000
[    1.987820@3] fe00: 349b0068 00000000 00000018 00000000 053bc650 ffffffc0 ffff8b7a 00000000
[    1.996100@3] fe20: 00001000 00000000 00000ffb 00000000 0000000e 00000000 00000007 00000000
[    2.004380@3] fe40: 00000001 00000000 0000000e 00000000 00000007 00000000 01ba1000 ffffffc0
[    2.012660@3] fe60: 00000011 00000000 78192058 ffffffc0 00000000 00000000 00000000 00000000
[    2.020940@3] fe80: 64238919 00000000 022d3000 ffffffc0 02135608 ffffffc0 021c3dd5 ffffffc0
[    2.029220@3] fea0: 00000003 00000000 01080210 ffffffc0 00000000 00000040 597cfef0 ffffffc0
[    2.037498@3] fec0: 016587ac ffffffc0 597cfef0 ffffffc0
[    2.042673@3] [<ffffffc001083da0>] el1_irq+0x60/0xd0
[    2.047591@3] [<ffffffc001658904>] cpuidle_idle_call+0xc0/0x24c
[    2.053455@3] [<ffffffc00108552c>] arch_cpu_idle+0x10/0x28
[    2.058889@3] [<ffffffc0010f8c74>] cpu_startup_entry+0x1d0/0x220
[    2.064840@3] [<ffffffc00108f99c>] secondary_start_kernel+0x118/0x128
[    2.071225@4] CPU4: stopping
[    2.074075@4] CPU: 4 PID: 0 Comm: swapper/4 Not tainted 3.14.29-00001-g71ca4b4 #1
[    2.081485@4] Call trace:
[    2.084080@4] [<ffffffc001089060>] dump_backtrace+0x0/0x138
[    2.089596@4] [<ffffffc0010891b8>] show_stack+0x20/0x30
[    2.094771@4] [<ffffffc001b229ac>] dump_stack+0x7c/0xc0
[    2.099945@4] [<ffffffc00108ff3c>] handle_IPI+0x1b8/0x1c8
[    2.105293@4] [<ffffffc00108145c>] gic_handle_irq+0x80/0x88
[    2.110811@4] Exception stack(0xffffffc0597cbdb0 to 0xffffffc0597cbed0)
[    2.117368@4] bda0:                                     7819e058 ffffffc0 00000000 00000000
[    2.125650@4] bdc0: 597cbef0 ffffffc0 016587b0 ffffffc0 6744b726 00000000 6744b726 00000000
[    2.133929@4] bde0: bed563a4 0032a9b6 0003a7ec 00000000 00000000 00000000 29aaaaab 00000000
[    2.142210@4] be00: 349b0068 00000000 00000018 00000000 053bd650 ffffffc0 ffff8b7f 00000000
[    2.150489@4] be20: 00001000 00000000 00000ffe 00000000 0000a7f4 00000000 00000006 00000000
[    2.158770@4] be40: e0ccdeeb 00000000 01b35f28 ffffffc0 011bfb64 ffffffc0 00000000 00000000
[    2.167049@4] be60: 0000003d 00000000 7819e058 ffffffc0 00000000 00000000 00000000 00000000
[    2.175330@4] be80: 671e88e6 00000000 022d3000 ffffffc0 02135608 ffffffc0 021c3dd5 ffffffc0
[    2.183610@4] bea0: 00000004 00000000 01080210 ffffffc0 00000000 00000040 597cbef0 ffffffc0
[    2.191887@4] bec0: 016587ac ffffffc0 597cbef0 ffffffc0
[    2.197062@4] [<ffffffc001083da0>] el1_irq+0x60/0xd0
[    2.201981@4] [<ffffffc001658904>] cpuidle_idle_call+0xc0/0x24c
[    2.207845@4] [<ffffffc00108552c>] arch_cpu_idle+0x10/0x28
[    2.213279@4] [<ffffffc0010f8c74>] cpu_startup_entry+0x1d0/0x220
[    2.219229@4] [<ffffffc00108f99c>] secondary_start_kernel+0x118/0x128
[    2.225610@5] CPU5: stopping
[    2.228458@5] CPU: 5 PID: 0 Comm: swapper/5 Not tainted 3.14.29-00001-g71ca4b4 #1
[    2.235872@5] Call trace:
[    2.238464@5] [<ffffffc001089060>] dump_backtrace+0x0/0x138
[    2.243983@5] [<ffffffc0010891b8>] show_stack+0x20/0x30
[    2.249158@5] [<ffffffc001b229ac>] dump_stack+0x7c/0xc0
[    2.254332@5] [<ffffffc00108ff3c>] handle_IPI+0x1b8/0x1c8
[    2.259680@5] [<ffffffc00108145c>] gic_handle_irq+0x80/0x88
[    2.265199@5] Exception stack(0xffffffc0597c7db0 to 0xffffffc0597c7ed0)
[    2.271756@5] 7da0:                                     781aa058 ffffffc0 00000000 00000000
[    2.280037@5] 7dc0: 597c7ef0 ffffffc0 016587b0 ffffffc0 6744b603 00000000 6744b603 00000000
[    2.288317@5] 7de0: 9b2ab8f7 0032a9b5 0003a7e5 00000000 00000000 00000000 29aaaaab 00000000
[    2.296597@5] 7e00: 349b0068 00000000 00000018 00000000 053be650 ffffffc0 597c7da0 ffffffc0
[    2.304877@5] 7e20: 00001000 00000000 00000ffe 00000000 00000001 00000000 a54f9f0c 0000007f
[    2.313157@5] 7e40: 00000000 00000000 a5866036 0000007f 00000000 00000000 a54f9f0c 0000007f
[    2.321437@5] 7e60: 60c1fe96 6c87e0be 781aa058 ffffffc0 00000000 00000000 00000000 00000000
[    2.329717@5] 7e80: 671e6471 00000000 022d3000 ffffffc0 02135608 ffffffc0 021c3dd5 ffffffc0
[    2.337997@5] 7ea0: 00000005 00000000 01080210 ffffffc0 00000000 00000040 597c7ef0 ffffffc0
[    2.346275@5] 7ec0: 016587ac ffffffc0 597c7ef0 ffffffc0
[    2.351450@5] [<ffffffc001083da0>] el1_irq+0x60/0xd0
[    2.356368@5] [<ffffffc001658904>] cpuidle_idle_call+0xc0/0x24c
[    2.362232@5] [<ffffffc00108552c>] arch_cpu_idle+0x10/0x28
[    2.367665@5] [<ffffffc0010f8c74>] cpu_startup_entry+0x1d0/0x220
[    2.373617@5] [<ffffffc00108f99c>] secondary_start_kernel+0x118/0x128
[    2.379998@2] CPU2: stopping
[    2.382845@2] CPU: 2 PID: 0 Comm: swapper/2 Not tainted 3.14.29-00001-g71ca4b4 #1
[    2.390259@2] Call trace:
[    2.392850@2] [<ffffffc001089060>] dump_backtrace+0x0/0x138
[    2.398369@2] [<ffffffc0010891b8>] show_stack+0x20/0x30
[    2.403544@2] [<ffffffc001b229ac>] dump_stack+0x7c/0xc0
[    2.408719@2] [<ffffffc00108ff3c>] handle_IPI+0x1b8/0x1c8
[    2.414066@2] [<ffffffc00108145c>] gic_handle_irq+0x80/0x88
[    2.419585@2] Exception stack(0xffffffc0597d3db0 to 0xffffffc0597d3ed0)
[    2.426141@2] 3da0:                                     78186058 ffffffc0 00000002 00000000
[    2.434423@2] 3dc0: 597d3ef0 ffffffc0 016587b0 ffffffc0 67466d4d 00000000 67466d4d 00000000
[    2.442703@2] 3de0: e58011d0 0032ab6c 0003b270 00000000 00000000 00000000 29aaaaab 00000000
[    2.450982@2] 3e00: 349b0068 00000000 00000018 00000000 b5193519 00000032 01083000 ffffffc0
[    2.459262@2] 3e20: 00000000 00000000 00000000 00000000 34d5d83d 00000000 00000000 00000000
[    2.467542@2] 3e40: 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
[    2.475822@2] 3e60: 00000000 00000000 78186058 ffffffc0 00000002 00000000 00000002 00000000
[    2.484102@2] 3e80: 67439693 00000000 022d3000 ffffffc0 02135608 ffffffc0 021c3dd5 ffffffc0
[    2.492383@2] 3ea0: 7818605c ffffffc0 01080210 ffffffc0 00000000 00000040 597d3ef0 ffffffc0
[    2.500661@2] 3ec0: 016587ac ffffffc0 597d3ef0 ffffffc0
[    2.505836@2] [<ffffffc001083da0>] el1_irq+0x60/0xd0
[    2.510753@2] [<ffffffc001658a40>] cpuidle_idle_call+0x1fc/0x24c
[    2.516704@2] [<ffffffc00108552c>] arch_cpu_idle+0x10/0x28
[    2.522138@2] [<ffffffc0010f8c74>] cpu_startup_entry+0x1d0/0x220
[    2.528089@2] [<ffffffc00108f99c>] secondary_start_kernel+0x118/0x128
[    2.534471@6] CPU6: stopping
[    2.537320@6] CPU: 6 PID: 0 Comm: swapper/6 Not tainted 3.14.29-00001-g71ca4b4 #1
[    2.544733@6] Call trace:
[    2.547326@6] [<ffffffc001089060>] dump_backtrace+0x0/0x138
[    2.552844@6] [<ffffffc0010891b8>] show_stack+0x20/0x30
[    2.558019@6] [<ffffffc001b229ac>] dump_stack+0x7c/0xc0
[    2.563194@6] [<ffffffc00108ff3c>] handle_IPI+0x1b8/0x1c8
[    2.568541@6] [<ffffffc00108145c>] gic_handle_irq+0x80/0x88
[    2.574060@6] Exception stack(0xffffffc0597c3db0 to 0xffffffc0597c3ed0)
[    2.580617@6] 3da0:                                     781b6058 ffffffc0 00000002 00000000
[    2.588898@6] 3dc0: 597c3ef0 ffffffc0 016587b0 ffffffc0 67469145 00000000 67469145 00000000
[    2.597178@6] 3de0: ddd5676f 0032ab90 0003b34d 00000000 00000000 00000000 29aaaaab 00000000
[    2.605458@6] 3e00: 349b0068 00000000 00000018 00000000 b5193519 00000032 01083000 ffffffc0
[    2.613738@6] 3e20: 00000000 00000000 00000000 00000000 34d5d83d 00000000 00000000 00000000
[    2.622018@6] 3e40: 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
[    2.630298@6] 3e60: 00000000 00000000 781b6058 ffffffc0 00000002 00000000 00000002 00000000
[    2.638578@6] 3e80: 64272952 00000000 022d3000 ffffffc0 02135608 ffffffc0 021c3dd5 ffffffc0
[    2.646859@6] 3ea0: 781b605c ffffffc0 01080210 ffffffc0 00000000 00000040 597c3ef0 ffffffc0
[    2.655136@6] 3ec0: 016587ac ffffffc0 597c3ef0 ffffffc0
[    2.660311@6] [<ffffffc001083da0>] el1_irq+0x60/0xd0
[    2.665229@6] [<ffffffc001658a40>] cpuidle_idle_call+0x1fc/0x24c
[    2.671179@6] [<ffffffc00108552c>] arch_cpu_idle+0x10/0x28
[    2.676613@6] [<ffffffc0010f8c74>] cpu_startup_entry+0x1d0/0x220
[    2.682564@6] [<ffffffc00108f99c>] secondary_start_kernel+0x118/0x128
[    2.688945@7] CPU7: stopping
[    2.691793@7] CPU: 7 PID: 0 Comm: swapper/7 Not tainted 3.14.29-00001-g71ca4b4 #1
[    2.699207@7] Call trace:
[    2.701799@7] [<ffffffc001089060>] dump_backtrace+0x0/0x138
[    2.707318@7] [<ffffffc0010891b8>] show_stack+0x20/0x30
[    2.712493@7] [<ffffffc001b229ac>] dump_stack+0x7c/0xc0
[    2.717667@7] [<ffffffc00108ff3c>] handle_IPI+0x1b8/0x1c8
[    2.723015@7] [<ffffffc00108145c>] gic_handle_irq+0x80/0x88
[    2.728534@7] Exception stack(0xffffffc0597bfdb0 to 0xffffffc0597bfed0)
[    2.735091@7] fda0:                                     781c2058 ffffffc0 00000002 00000000
[    2.743372@7] fdc0: 597bfef0 ffffffc0 016587b0 ffffffc0 6746e4ee 00000000 6746e4ee 00000000
[    2.751652@7] fde0: 868012c5 0032abe4 0003b54f 00000000 00000000 00000000 29aaaaab 00000000
[    2.759932@7] fe00: 349b0068 00000000 00000018 00000000 b5193519 00000032 01083000 ffffffc0
[    2.768212@7] fe20: 00000000 00000000 00000000 00000000 34d5d83d 00000000 00000000 00000000
[    2.776492@7] fe40: 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
[    2.784772@7] fe60: 00000000 00000000 781c2058 ffffffc0 00000002 00000000 00000002 00000000
[    2.793052@7] fe80: 67215394 00000000 022d3000 ffffffc0 02135608 ffffffc0 021c3dd5 ffffffc0
[    2.801333@7] fea0: 781c205c ffffffc0 01080210 ffffffc0 00000000 00000040 597bfef0 ffffffc0
[    2.805066@1] SMP: failed to stop secondary CPUs
[    2.814182@7] fec0: 016587ac ffffffc0 597bfef0 ffffffc0
[    2.819356@7] [<ffffffc001083da0>] el1_irq+0x60/0xd0
[    2.824274@7] [<ffffffc001658a40>] cpuidle_idle_call+0x1fc/0x24c
[    2.830224@7] [<ffffffc00108552c>] arch_cpu_idle+0x10/0x28
[    2.835658@7] [<ffffffc0010f8c74>] cpu_startup_entry+0x1d0/0x220
[    2.841609@7] [<ffffffc00108f99c>] secondary_start_kernel+0x118/0x128