恩山无线论坛

 找回密码
 立即注册

QQ登录

只需一步,快速开始

搜索
查看: 417|回复: 5

[N1盒子] 【已解决】哪位大神知道这是什么系统?

[复制链接]
发表于 2020-8-31 22:28 | 显示全部楼层 |阅读模式
本帖最后由 cynizy 于 2020-9-7 09:38 编辑
  1. BL2 Built : 11:58:42, May 27 2017.
  2. gxl gc3c9a84 - xiaobo.gu@droid05

  3. set vdd cpu_a to 1120 mv
  4. set vdd cpu_b to 1050 mv
  5. set vddee to 1000 mv
  6. Board ID = 4
  7. CPU clk: 1200MHz
  8. DQS-corr enabled
  9. DDR scramble enabled
  10. DDR3 chl: Rank0+1 [url=home.php?mod=space&uid=162986]@[/url] 912MHz - PASS
  11. Rank0: 1024MB(auto)-2T-13
  12. Rank1: 1024MB(auto)-2T-13
  13. DataBus test pass!
  14. AddrBus test pass!
  15. -s
  16. Load fip header from eMMC, src: 0x0000c200, des: 0x01400000, size: 0x00004000
  17. aml log : R2048 check pass!
  18. New fip structure!
  19. Load bl30 from eMMC, src: 0x00010200, des: 0x01700000, size: 0x0000d600
  20. aml log : R2048 check pass!
  21. Load bl31 from eMMC, src: 0x00020200, des: 0x01700000, size: 0x0002c600
  22. aml log : R2048 check pass!
  23. Load bl33 from eMMC, src: 0x00050200, des: 0x01700000, size: 0x00053400
  24. aml log : R2048 check pass!
  25. NOTICE:  BL3-1: v1.0(release):a625749
  26. NOTICE:  BL3-1: Built : 11:25:15, Aug 25 2017
  27. [BL31]: GXL CPU setup!
  28. NOTICE:  BL31: BL33 decompress pass
  29. mpu_config_enable:ok
  30. [Image: gxl_v1.1.3243-377db0f 2017-09-07 11:28:58 qiufang.dai@droid07]
  31. OPS=0x04
  32. 30 28 e2 3 7 73 da 5e e9 43 37 40 [0.839490 Inits done]
  33. secure task start!
  34. high task start!
  35. low task start!
  36. ERROR:   Error initializing runtime service opteed_fast


  37. U-Boot 2015.01-00010-gfe36fb9-dirty (Mar 17 2018 - 12:20:04)

  38. DRAM:  2 GiB
  39. Relocation Offset is: 76ed9000
  40. register usb cfg[0][1] = 0000000077f5d368
  41. [CANVAS]canvas init
  42. vpu: error: vpu: check dts: FDT_ERR_BADMAGIC, load default parameters
  43. vpu: clk_level = 7
  44. vpu: set clk: 666667000Hz, readback: 666660000Hz(0x300)
  45. vpu: vpu_clk_gate_init_off
  46. vpp: vpp_init
  47. MMC:   aml_priv->desc_buf = 0x0000000073ed9640
  48. aml_priv->desc_buf = 0x0000000073edb960
  49. SDIO Port B: 0, SDIO Port C: 1
  50. emmc/sd response timeout, cmd8, status=0x3ff2800
  51. emmc/sd response timeout, cmd55, status=0x3ff2800
  52. init_part() 278: PART_TYPE_DOS
  53. [mmc_init] mmc init success
  54. dtb magic 71b104da
  55. aml log : R2048 check pass!
  56.       Amlogic multi-dtb tool
  57.       Multi dtb detected
  58.       Multi dtb tool version: v2 .
  59.       Support 2 dtbs.
  60.         aml_dt soc: gxl platform: p230 variant: 2g
  61.         dtb 0 soc: gxl   plat: p230   vari: 1g
  62.         dtb 1 soc: gxl   plat: p230   vari: 2g
  63.       Find match dtb: 1
  64. start dts,buffer=0000000073ede1b0,dt_addr=0000000073ee91b0
  65.       Amlogic multi-dtb tool
  66.       Multi dtb detected
  67.       Multi dtb tool version: v2 .
  68.       Support 2 dtbs.
  69.         aml_dt soc: gxl platform: p230 variant: 2g
  70.         dtb 0 soc: gxl   plat: p230   vari: 1g
  71.         dtb 1 soc: gxl   plat: p230   vari: 2g
  72.       Find match dtb: 1
  73. parts: 10
  74. 00:      logo   0000000002000000 1
  75. 01:  recovery   0000000002000000 1
  76. 02:       rsv   0000000000800000 1
  77. 03:       tee   0000000000800000 1
  78. 04:     crypt   0000000002000000 1
  79. 05:      misc   0000000002000000 1
  80. 06:      boot   0000000002000000 1
  81. 07:    system   0000000050000000 1
  82. 08:     cache   0000000020000000 2
  83. 09:      data   ffffffffffffffff 4
  84. init_part() 278: PART_TYPE_DOS
  85. eMMC/TSD partition table have been checked OK!
  86. check pattern success
  87. mmc env offset: 0x27400000
  88. In:    serial
  89. Out:   serial
  90. Err:   serial
  91. reboot_mode=cold_boot
  92. hpd_state=0
  93. cvbs performance type = 6, table = 0
  94. [store]To run cmd[emmc dtb_read 0x1000000 0x40000]
  95. _verify_dtb_checksum()-917: calc 90c99aaa, store 90c99aaa
  96. _verify_dtb_checksum()-917: calc 90c99aaa, store 90c99aaa
  97. dtb_read()-1039: total valid 2
  98. dtb_read()-1106: do nothing
  99. aml log : R2048 check pass!
  100.       Amlogic multi-dtb tool
  101.       Multi dtb detected
  102.       Multi dtb tool version: v2 .
  103.       Support 2 dtbs.
  104.         aml_dt soc: gxl platform: p230 variant: 2g
  105.         dtb 0 soc: gxl   plat: p230   vari: 1g
  106.         dtb 1 soc: gxl   plat: p230   vari: 2g
  107.       Find match dtb: 1
  108. vpp: vpp_pq_load pq val error !!!
  109. Net:   Phy 0 not found
  110. dwmac.c9410000amlkey_init() enter!
  111. [EFUSE_MSG]keynum is 4
  112. [BL31]: tee size: 0

  113. Start read misc partition datas!
  114. info->attemp_times = 0
  115. info->active_slot = 0
  116. info->slot_info[0].bootable = 1
  117. info->slot_info[0].online = 1
  118. info->slot_info[1].bootable = 0
  119. info->slot_info[1].online = 0
  120. info->attemp_times = 0
  121. attemp_times = 0
  122. active slot = 0
  123. wipe_data=successful
  124. wipe_cache=successful
  125. upgrade_step=2
  126. [OSD]load fb addr from dts
  127. [OSD]fb_addr for logo: 0x7f851000
  128. [OSD]load fb addr from dts
  129. [OSD]fb_addr for logo: 0x7f851000
  130. [CANVAS]addr=0x7f851000 width=3840, height=2160
  131. amlkey_init() enter!
  132. amlkey_init() 71: already init!
  133. [EFUSE_MSG]keynum is 4
  134. [BL31]: tee size: 0
  135. [BL31]: tee size: 0
  136. [BL31]: tee size: 0
  137. [BL31]: tee size: 0
  138. [BL31]: tee size: 0
  139. [KM]Error:f[key_manage_query_size]L507:key[deviceid] not programed yet
  140. gpio: pin GPIOAO_2 (gpio 102) value is 1
  141. Hit Enter or space or Ctrl+C key to stop autoboot -- :  0
  142. (Re)start USB...
  143. USB0:   USB3.0 XHCI init start
  144. Register 2000140 NbrPorts 2
  145. Starting the controller
  146. USB XHCI 1.00
  147. scanning bus 0 for devices... 1 USB Device(s) found
  148.        scanning usb for storage devices... 0 Storage Device(s) found
  149. ** Bad device usb 0 **
  150. ** Bad device usb 1 **
  151. ** Bad device usb 2 **
  152. ** Bad device usb 3 **
  153. card out
  154. emmc/sd response timeout, cmd8, status=0x1ff2800
  155. emmc/sd response timeout, cmd55, status=0x1ff2800
  156. emmc/sd response timeout, cmd1, status=0x1ff2800
  157. reading emmc_autoscript
  158. 521 bytes read in 3 ms (168.9 KiB/s)
  159. ## Executing script at 01020000
  160. reading zImage
  161. 20537352 bytes read in 567 ms (34.5 MiB/s)
  162. reading uInitrd
  163. 5476693 bytes read in 153 ms (34.1 MiB/s)
  164. reading uEnv.ini
  165. 245 bytes read in 2 ms (119.1 KiB/s)
  166. reading /dtb/meson-gxl-s905d-phicomm-n1.dtb
  167. 26897 bytes read in 6 ms (4.3 MiB/s)
  168. [rsvmem] get fdtaddr NULL!
  169. rsvmem - reserve memory

  170. Usage:
  171. rsvmem check                   - check reserved memory
  172. rsvmem dump                    - dump reserved memory

  173. rsvmem check failed
  174. ## Loading init Ramdisk from Legacy Image at 13000000 ...
  175.    Image Name:   uInitrd
  176.    Image Type:   AArch64 Linux RAMDisk Image (gzip compressed)
  177.    Data Size:    5476629 Bytes = 5.2 MiB
  178.    Load Address: 00000000
  179.    Entry Point:  00000000
  180.    Verifying Checksum ... OK
  181. load dtb from 0x1000000 ......
  182.       Amlogic multi-dtb tool
  183.       Single dtb detected
  184. ## Flattened Device Tree blob at 01000000
  185.    Booting using the fdt blob at 0x1000000
  186. libfdt fdt_path_offset() returned FDT_ERR_NOTFOUND
  187. [rsvmem] fdt get prop fail.
  188.    Loading Ramdisk to 7398d000, end 73ec6115 ... OK
  189.    Loading Device Tree to 000000001fff6000, end 000000001ffff910 ... OK
  190. fdt_instaboot: no instaboot image

  191. Starting kernel ...

  192. uboot time: 4647994 us
  193. [    0.000000] Booting Linux on physical CPU 0x0000000000 [0x410fd034]
  194. [    0.000000] Linux version 5.1.0.1-ydc-n1-aml-s905 (root@t2) (gcc version 7.4.1 20181213 [linaro-7.4-2019.02 revision 56ec6f6b99cc167ff0c2f8e1a2eed33b1edc85d4] (Linaro GCC 7.4-2019.02)) #5.90 SMP PREEMPT Wed Jul 24 10:12:19 UTC 2019
  195. [    0.000000] Machine model: Phicomm N1
  196. [    0.000000] Reserved memory: created CMA memory pool at 0x000000003b800000, size 896 MiB
  197. [    0.000000] OF: reserved mem: initialized node linux,cma, compatible id shared-dma-pool
  198. [    0.000000] psci: probing for conduit method from DT.
  199. [    0.000000] psci: PSCIv0.2 detected in firmware.
  200. [    0.000000] psci: Using standard PSCI v0.2 function IDs
  201. [    0.000000] psci: Trusted OS migration not required
  202. [    0.000000] random: get_random_bytes called from start_kernel+0xa4/0x458 with crng_init=0
  203. [    0.000000] percpu: Embedded 23 pages/cpu s55512 r8192 d30504 u94208
  204. [    0.000000] Detected VIPT I-cache on CPU0
  205. [    0.000000] CPU features: detected: ARM erratum 845719
  206. [    0.000000] Built 1 zonelists, mobility grouping on.  Total pages: 470336
  207. [    0.000000] Kernel command line: root=LABEL=ROOT_EMMC rootflags=data=writeback rw console=ttyAML0,115200n8 console=tty0 no_console_suspend consoleblank=0 fsck.fix=yes fsck.repair=yes net.ifnames=0 transparent_hugepage=never
  208. [    0.000000] Dentry cache hash table entries: 262144 (order: 9, 2097152 bytes)
  209. [    0.000000] Inode-cache hash table entries: 131072 (order: 8, 1048576 bytes)
  210. [    0.000000] Memory: 926092K/1911808K available (13630K kernel code, 1176K rwdata, 4520K rodata, 640K init, 791K bss, 68212K reserved, 917504K cma-reserved)
  211. [    0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1
  212. [    0.000000] rcu: Preemptible hierarchical RCU implementation.
  213. [    0.000000] rcu:     RCU restricting CPUs from NR_CPUS=64 to nr_cpu_ids=4.
  214. [    0.000000]  Tasks RCU enabled.
  215. [    0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 25 jiffies.
  216. [    0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=4
  217. [    0.000000] NR_IRQS: 64, nr_irqs: 64, preallocated irqs: 0
  218. [    0.000000] GIC: Using split EOI/Deactivate mode
  219. [    0.000000] irq_meson_gpio: 110 to 8 gpio interrupt mux initialized
  220. [    0.000000] arch_timer: cp15 timer(s) running at 24.00MHz (phys).
  221. [    0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x588fe9dc0, max_idle_ns: 440795202592 ns
  222. [    0.000003] sched_clock: 56 bits at 24MHz, resolution 41ns, wraps every 4398046511097ns
  223. [    0.000355] Console: colour dummy device 80x25
  224. [    0.000629] printk: console [tty0] enabled
  225. [    0.000662] Calibrating delay loop (skipped), value calculated using timer frequency.. 48.00 BogoMIPS (lpj=96000)
  226. [    0.000682] pid_max: default: 32768 minimum: 301
  227. [    0.000759] LSM: Security Framework initializing
  228. [    0.000805] SELinux:  Initializing.
  229. [    0.000852] *** VALIDATE SELinux ***
  230. [    0.000898] Mount-cache hash table entries: 4096 (order: 3, 32768 bytes)
  231. [    0.000919] Mountpoint-cache hash table entries: 4096 (order: 3, 32768 bytes)
  232. [    0.001279] *** VALIDATE proc ***
  233. [    0.001469] *** VALIDATE cgroup1 ***
  234. [    0.001481] *** VALIDATE cgroup2 ***
  235. [    0.024008] ASID allocator initialised with 32768 entries
  236. [    0.031995] rcu: Hierarchical SRCU implementation.
  237. [    0.048047] smp: Bringing up secondary CPUs ...
  238. [    0.080247] Detected VIPT I-cache on CPU1
  239. [    0.080294] CPU1: Booted secondary processor 0x0000000001 [0x410fd034]
  240. [    0.112289] Detected VIPT I-cache on CPU2
  241. [    0.112328] CPU2: Booted secondary processor 0x0000000002 [0x410fd034]
  242. [    0.144342] Detected VIPT I-cache on CPU3
  243. [    0.144378] CPU3: Booted secondary processor 0x0000000003 [0x410fd034]
  244. [    0.144446] smp: Brought up 1 node, 4 CPUs
  245. [    0.144508] SMP: Total of 4 processors activated.
  246. [    0.144520] CPU features: detected: 32-bit EL0 Support
  247. [    0.144532] CPU features: detected: CRC32 instructions
  248. [    0.144822] CPU: All CPU(s) started at EL2
  249. [    0.144843] alternatives: patching kernel code
  250. [    0.145670] devtmpfs: initialized
  251. [    0.149794] Registered cp15_barrier emulation handler
  252. [    0.149820] Registered setend emulation handler
  253. [    0.150081] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041785100000 ns
  254. [    0.150108] futex hash table entries: 1024 (order: 4, 65536 bytes)
  255. [    0.173264] xor: measuring software checksum speed
  256. [    0.212358]    8regs     :  2303.000 MB/sec
  257. [    0.252387]    32regs    :  2831.000 MB/sec
  258. [    0.292419]    arm64_neon:  2456.000 MB/sec
  259. [    0.292429] xor: using function: 32regs (2831.000 MB/sec)
  260. [    0.292486] pinctrl core: initialized pinctrl subsystem
  261. [    0.293351] NET: Registered protocol family 16
  262. [    0.293778] audit: initializing netlink subsys (disabled)
  263. [    0.293941] audit: type=2000 audit(0.292:1): state=initialized audit_enabled=0 res=1
  264. [    0.294558] cpuidle: using governor menu
  265. [    0.294914] vdso: 2 pages (1 code @ (____ptrval____), 1 data @ (____ptrval____))
  266. [    0.294934] hw-breakpoint: found 6 breakpoint and 4 watchpoint registers.
  267. [    0.297229] DMA: preallocated 256 KiB pool for atomic allocations
  268. [    0.297883] Serial: AMBA PL011 UART driver
  269. [    0.309128] HugeTLB registered 1.00 GiB page size, pre-allocated 0 pages
  270. [    0.309153] HugeTLB registered 32.0 MiB page size, pre-allocated 0 pages
  271. [    0.309165] HugeTLB registered 2.00 MiB page size, pre-allocated 0 pages
  272. [    0.309178] HugeTLB registered 64.0 KiB page size, pre-allocated 0 pages
  273. [    0.309478] cryptd: max_cpu_qlen set to 1000
  274. [    0.309797] raid6: using algorithm neonx8 gen() 0 MB/s
  275. [    0.309814] raid6: .... xor() 0 MB/s, rmw enabled
  276. [    0.309824] raid6: using neon recovery algorithm
  277. [    0.309958] fbcon: Taking over console
  278. [    0.311330] SCSI subsystem initialized
  279. [    0.311493] usbcore: registered new interface driver usbfs
  280. [    0.311528] usbcore: registered new interface driver hub
  281. [    0.311593] usbcore: registered new device driver usb
  282. [    0.311942] pps_core: LinuxPPS API ver. 1 registered
  283. [    0.311953] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
  284. [    0.311978] PTP clock support registered
  285. [    0.312086] EDAC MC: Ver: 3.0.0
  286. [    0.312625] Advanced Linux Sound Architecture Driver Initialized.
  287. [    0.313028] NetLabel: Initializing
  288. [    0.313042] NetLabel:  domain hash size = 128
  289. [    0.313051] NetLabel:  protocols = UNLABELED CIPSOv4 CALIPSO
  290. [    0.313102] NetLabel:  unlabeled traffic allowed by default
  291. [    0.313502] clocksource: Switched to clocksource arch_sys_counter
  292. [    0.313696] VFS: Disk quotas dquot_6.6.0
  293. [    0.313747] VFS: Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
  294. [    0.313845] FS-Cache: Loaded
  295. [    0.313862] *** VALIDATE hugetlbfs ***
  296. [    0.318647] NET: Registered protocol family 2
  297. [    0.319088] tcp_listen_portaddr_hash hash table entries: 1024 (order: 2, 16384 bytes)
  298. [    0.319131] TCP established hash table entries: 16384 (order: 5, 131072 bytes)
  299. [    0.319247] TCP bind hash table entries: 16384 (order: 6, 262144 bytes)
  300. [    0.319469] TCP: Hash tables configured (established 16384 bind 16384)
  301. [    0.319600] UDP hash table entries: 1024 (order: 3, 32768 bytes)
  302. [    0.319651] UDP-Lite hash table entries: 1024 (order: 3, 32768 bytes)
  303. [    0.319835] NET: Registered protocol family 1
  304. [    0.320256] RPC: Registered named UNIX socket transport module.
  305. [    0.320275] RPC: Registered udp transport module.
  306. [    0.320285] RPC: Registered tcp transport module.
  307. [    0.320294] RPC: Registered tcp NFSv4.1 backchannel transport module.
  308. [    0.320309] NET: Registered protocol family 44
  309. [    0.320514] Trying to unpack rootfs image as initramfs...
  310. [    0.551789] Freeing initrd memory: 5348K
  311. [    0.552518] hw perfevents: enabled with armv8_cortex_a53 PMU driver, 7 counters available
  312. [    0.552796] kvm [1]: IPA Size Limit: 40bits
  313. [    0.553310] kvm [1]: vgic interrupt IRQ1
  314. [    0.553400] kvm [1]: Hyp mode initialized successfully
  315. [    0.679137] Initialise system trusted keyrings
  316. [    0.679317] workingset: timestamp_bits=46 max_order=19 bucket_order=0
  317. [    0.683499] zbud: loaded
  318. [    0.684733] squashfs: version 4.0 (2009/01/31) Phillip Lougher
  319. [    0.684953] FS-Cache: Netfs 'nfs' registered for caching
  320. [    0.685413] NFS: Registering the id_resolver key type
  321. [    0.685445] Key type id_resolver registered
  322. [    0.685454] Key type id_legacy registered
  323. [    0.685472] nfs4filelayout_init: NFSv4 File Layout Driver Registering...
  324. [    0.685484] Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
  325. [    0.686258] FS-Cache: Netfs 'cifs' registered for caching
  326. [    0.686505] Key type cifs.spnego registered
  327. [    0.686523] Key type cifs.idmap registered
  328. [    0.686543] ntfs: driver 2.1.32 [Flags: R/W].
  329. [    0.687048] JFS: nTxBlock = 8192, nTxLock = 65536
  330. [    0.690856] SGI XFS with ACLs, security attributes, realtime, no debug enabled
  331. [    0.692183] ocfs2: Registered cluster interface o2cb
  332. [    0.692381] OCFS2 User DLM kernel interface loaded
  333. [    0.693789] gfs2: GFS2 installed
  334. [    0.825059] Key type asymmetric registered
  335. [    0.825081] Asymmetric key parser 'x509' registered
  336. [    0.825141] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 244)
  337. [    0.825293] io scheduler mq-deadline registered
  338. [    0.825305] io scheduler kyber registered
  339. [    0.825443] io scheduler bfq registered
  340. [    0.840277] soc soc0: Amlogic Meson GXL (S905D) Revision 21:d (4:2) Detected
  341. [    0.843268] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled
  342. [    0.844492] Serial: AMBA driver
  343. [    0.844809] c11084c0.serial: ttyAML6 at MMIO 0xc11084c0 (irq = 10, base_baud = 1500000) is a meson_uart
  344. [    0.844939] serial serial0: tty port ttyAML6 registered
  345. [    0.845125] c81004c0.serial: ttyAML0 at MMIO 0xc81004c0 (irq = 13, base_baud = 1500000) is a meson_uart
  346. [    1.697691] printk: console [ttyAML0] enabled
  347. [    1.705718] brd: module loaded
  348. [    1.709340] loop: module loaded
  349. [    1.710582] libphy: Fixed MDIO Bus: probed
  350. [    1.712495] tun: Universal TUN/TAP device driver, 1.6
  351. [    1.718849] meson8b-dwmac c9410000.ethernet: PTP uses main clock
  352. [    1.723143] meson8b-dwmac c9410000.ethernet: no reset control found
  353. [    1.729802] meson8b-dwmac c9410000.ethernet: User ID: 0x11, Synopsys ID: 0x37
  354. [    1.736410] meson8b-dwmac c9410000.ethernet:         DWMAC1000
  355. [    1.741570] meson8b-dwmac c9410000.ethernet: DMA HW capability register supported
  356. [    1.748984] meson8b-dwmac c9410000.ethernet: RX Checksum Offload Engine supported
  357. [    1.756401] meson8b-dwmac c9410000.ethernet: COE Type 2
  358. [    1.761576] meson8b-dwmac c9410000.ethernet: TX Checksum insertion supported
  359. [    1.768563] meson8b-dwmac c9410000.ethernet: Wake-Up On Lan supported
  360. [    1.774977] meson8b-dwmac c9410000.ethernet: Normal descriptors
  361. [    1.780811] meson8b-dwmac c9410000.ethernet: Ring mode enabled
  362. [    1.786589] meson8b-dwmac c9410000.ethernet: Enable RX Mitigation via HW Watchdog Timer
  363. [    2.849528] libphy: stmmac: probed
  364. [    2.850433] VFIO - User Level meta-driver version: 0.3
  365. [    2.853291] dwc3 c9000000.dwc3: Failed to get clk 'ref': -2
  366. [    2.859429] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
  367. [    2.864452] ehci-platform: EHCI generic platform driver
  368. [    2.869718] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
  369. [    2.875700] ohci-platform: OHCI generic platform driver
  370. [    2.881367] usbcore: registered new interface driver usb-storage
  371. [    2.888007] mousedev: PS/2 mouse device common for all mice
  372. [    2.892908] i2c /dev entries driver
  373. [    2.897564] sdhci: Secure Digital Host Controller Interface driver
  374. [    2.901908] sdhci: Copyright(c) Pierre Ossman
  375. [    2.906327] Synopsys Designware Multimedia Card Interface Driver
  376. [    2.913555] meson-gx-mmc d0072000.mmc: Got CD GPIO
  377. [    2.943865] meson-gx-mmc d0074000.mmc: allocated mmc-pwrseq
  378. [    2.970972] sdhci-pltfm: SDHCI platform and OF driver helper
  379. [    2.971833] ledtrig-cpu: registered to indicate activity on CPUs
  380. [    2.977426] meson-sm: secure-monitor enabled
  381. [    2.981434] hidraw: raw HID events driver (C) Jiri Kosina
  382. [    2.986850] usbcore: registered new interface driver usbhid
  383. [    2.992103] usbhid: USB HID core driver
  384. [    2.996179] platform-mhu c883c404.mailbox: Platform MHU Mailbox registered
  385. [BL31]: tee size: 0
  386. [    3.006853] NET: Registered protocol family 17
  387. [    3.009198] Key type dns_resolver registered
  388. [    3.013901] registered taskstats version 1
  389. [    3.017255] Loading compiled-in X.509 certificates
  390. [    3.022189] zswap: loaded using pool lzo/zbud
  391. [    3.027263] Btrfs loaded, crc32c=crc32c-generic
  392. [    3.038202] Key type encrypted registered
  393. [    3.050986] meson-drm d0100000.vpu: Queued 2 outputs on vpu
  394. [    3.051328] [drm] Supports vblank timestamp caching Rev 2 (21.10.2013).
  395. [    3.057507] [drm] No driver support for vblank timestamp query.
  396. [    3.063466] meson-drm d0100000.vpu: CVBS Output connector not available
  397. [    3.064419] mmc1: new HS200 MMC card at address 0001
  398. [    3.075808] mmcblk1: mmc1:0001 8GTF4R 7.28 GiB
  399. [    3.079939] mmcblk1boot0: mmc1:0001 8GTF4R partition 1 4.00 MiB
  400. [    3.085811] mmcblk1boot1: mmc1:0001 8GTF4R partition 2 4.00 MiB
  401. [    3.091218] mmcblk1rpmb: mmc1:0001 8GTF4R partition 3 512 KiB, chardev (241:0)
  402. [    3.097584] meson-dw-hdmi c883a000.hdmi-tx: Detected HDMI TX controller v2.01a with HDCP (meson_dw_hdmi_phy)
  403. [    3.099371]  mmcblk1: p1 p2
  404. [    3.108485] meson-dw-hdmi c883a000.hdmi-tx: registered DesignWare HDMI I2C bus driver
  405. [    3.118982] meson-drm d0100000.vpu: bound c883a000.hdmi-tx (ops meson_dw_hdmi_ops)
  406. [    3.126365] [drm] Initialized meson 1.0.0 20161109 for d0100000.vpu on minor 0
  407. [    3.133180] [drm] Cannot find any crtc or sizes
  408. [    3.138026] libphy: mdio_mux: probed
  409. [    3.141236] [drm] Cannot find any crtc or sizes
  410. [    3.145954] libphy: mdio_mux: probed
  411. [    3.151914] phy phy-d0078080.phy.2: unsupported PHY mode 5
  412. [    3.156740] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller
  413. [    3.160059] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 1
  414. [    3.168421] xhci-hcd xhci-hcd.0.auto: hcc params 0x0228f664 hci version 0x100 quirks 0x0000000002010010
  415. [    3.177000] xhci-hcd xhci-hcd.0.auto: irq 37, io mem 0xc9000000
  416. [    3.183109] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 5.01
  417. [    3.191016] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
  418. [    3.198168] usb usb1: Product: xHCI Host Controller
  419. [    3.202995] usb usb1: Manufacturer: Linux 5.1.0.1-ydc-n1-aml-s905 xhci-hcd
  420. [    3.209809] usb usb1: SerialNumber: xhci-hcd.0.auto
  421. [    3.215064] hub 1-0:1.0: USB hub found
  422. [    3.218381] hub 1-0:1.0: 2 ports detected
  423. [    3.222554] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller
  424. [    3.227761] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 2
  425. [    3.235349] xhci-hcd xhci-hcd.0.auto: Host supports USB 3.0  SuperSpeed
  426. [    3.241933] usb usb2: We don't know the algorithms for LPM for this host, disabling LPM.
  427. [    3.249991] usb usb2: New USB device found, idVendor=1d6b, idProduct=0003, bcdDevice= 5.01
  428. [    3.258113] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
  429. [    3.265269] usb usb2: Product: xHCI Host Controller
  430. [    3.270099] usb usb2: Manufacturer: Linux 5.1.0.1-ydc-n1-aml-s905 xhci-hcd
  431. [    3.276912] usb usb2: SerialNumber: xhci-hcd.0.auto
  432. [    3.282107] hub 2-0:1.0: USB hub found
  433. [    3.285460] hub 2-0:1.0: config failed, hub doesn't have any ports! (err -19)
  434. [    3.294395] scpi_protocol scpi: SCP Protocol legacy pre-1.0 firmware
  435. domain-0 init dvfs: 4
  436. [    3.313123] hctosys: unable to open rtc device (rtc0)
  437. [    3.313392] VDDAO_3V3: disabling
  438. [    3.315775] ALSA device list:
  439. [    3.318675]   No soundcards found.
  440. [    3.323018] Freeing unused kernel memory: 640K
  441. [    3.345610] Run /init as init process
  442. [    3.395401] random: systemd-udevd: uninitialized urandom read (16 bytes read)
  443. [    3.397365] random: systemd-udevd: uninitialized urandom read (16 bytes read)
  444. [    3.400518] random: udevadm: uninitialized urandom read (16 bytes read)
  445. [    3.575309] random: fast init done
  446. [    3.875831] EXT4-fs (mmcblk1p2): mounted filesystem with writeback data mode. Opts: data=writeback
  447. [    4.039446] systemd[1]: System time before build time, advancing clock.
  448. [    4.088977] NET: Registered protocol family 10
  449. [    4.107247] Segment Routing with IPv6
  450. [    4.126931] systemd[1]: systemd 232 running in system mode. (+PAM +AUDIT +SELINUX +IMA +APPARMOR +SMACK +SYSVINIT +UTMP +LIBCRYPTSETUP +GCRYPT +GNUTLS +ACL +XZ +LZ4 +SECCOMP +BLKID +ELFUTILS +KMOD +IDN)
  451. [    4.139754] systemd[1]: Detected architecture arm64.
  452. [    4.148726] systemd[1]: Set hostname to <0110000a789eeb3de49609f91>.
  453. [    4.361792] systemd[1]: Reached target Remote File Systems.
  454. [    4.364191] systemd[1]: Created slice User and Session Slice.
  455. [    4.367974] systemd[1]: Listening on LVM2 poll daemon socket.
  456. [    4.373551] systemd[1]: Listening on udev Kernel Socket.
  457. [    4.379936] systemd[1]: Created slice System Slice.
  458. [    4.384946] systemd[1]: Created slice system-serial\x2dgetty.slice.
  459. [    4.392736] systemd[1]: Mounting Huge Pages File System...
  460. [    4.481266] EXT4-fs (mmcblk1p2): re-mounted. Opts: (null)

  461. 0110000a789eeb3de49609f91
  462.               鈻堚枅鈻堚枅    鈻堚枅  鈻堚枅  鈻堚枅鈻堚枅鈻堚枅              
  463.   鈻堚枅鈻堚枅鈻堚枅鈻堚枅鈻堚枅  鈻堚枅鈻堚枅鈻堚枅  鈻堚枅  鈻堚枅      鈻堚枅  鈻堚枅鈻堚枅鈻堚枅鈻堚枅鈻堚枅  
  464.   鈻堚枅      鈻堚枅  鈻堚枅    鈻堚枅鈻堚枅鈻堚枅鈻堚枅鈻堚枅    鈻堚枅  鈻堚枅      鈻堚枅  
  465.   鈻堚枅      鈻堚枅  鈻堚枅  鈻堚枅  鈻堚枅    鈻堚枅  鈻堚枅鈻堚枅  鈻堚枅      鈻堚枅  
  466.   鈻堚枅      鈻堚枅  鈻堚枅              鈻堚枅  鈻堚枅  鈻堚枅      鈻堚枅  
  467.   鈻堚枅鈻堚枅鈻堚枅鈻堚枅鈻堚枅  鈻堚枅  鈻堚枅      鈻堚枅鈻堚枅  鈻堚枅鈻堚枅  鈻堚枅鈻堚枅鈻堚枅鈻堚枅鈻堚枅  
  468.               鈻堚枅  鈻堚枅  鈻堚枅  鈻堚枅  鈻堚枅  鈻堚枅              
  469. 鈻堚枅鈻堚枅鈻堚枅鈻堚枅鈻堚枅鈻堚枅鈻堚枅鈻堚枅  鈻堚枅鈻堚枅鈻堚枅鈻堚枅鈻堚枅      鈻堚枅鈻堚枅鈻堚枅鈻堚枅鈻堚枅鈻堚枅鈻堚枅鈻堚枅
  470.   鈻堚枅          鈻堚枅鈻堚枅      鈻堚枅  鈻堚枅  鈻堚枅鈻堚枅          鈻堚枅鈻堚枅
  471. 鈻堚枅    鈻堚枅鈻堚枅鈻堚枅鈻堚枅鈻堚枅  鈻堚枅鈻堚枅  鈻堚枅鈻堚枅  鈻堚枅    鈻堚枅鈻堚枅鈻堚枅  鈻堚枅  鈻堚枅
  472. 鈻堚枅鈻堚枅鈻堚枅  鈻堚枅鈻堚枅        鈻堚枅鈻堚枅鈻堚枅        鈻堚枅鈻堚枅    鈻堚枅鈻堚枅鈻堚枅  
  473.   鈻堚枅鈻堚枅鈻堚枅  鈻堚枅鈻堚枅        鈻堚枅鈻堚枅鈻堚枅鈻堚枅鈻堚枅鈻堚枅鈻堚枅    鈻堚枅  鈻堚枅   
  474. 鈻堚枅    鈻堚枅鈻堚枅      鈻堚枅  鈻堚枅鈻堚枅    鈻堚枅    鈻堚枅      鈻堚枅  鈻堚枅  
  475.     鈻堚枅    鈻堚枅鈻堚枅鈻堚枅鈻堚枅鈻堚枅  鈻堚枅鈻堚枅鈻堚枅  鈻堚枅鈻堚枅  鈻堚枅鈻堚枅鈻堚枅  鈻堚枅  鈻堚枅
  476.   鈻堚枅  鈻堚枅鈻堚枅鈻堚枅    鈻堚枅鈻堚枅鈻堚枅    鈻堚枅鈻堚枅  鈻堚枅鈻堚枅鈻堚枅  鈻堚枅  鈻堚枅鈻堚枅  
  477.   鈻堚枅      鈻堚枅鈻堚枅    鈻堚枅    鈻堚枅鈻堚枅鈻堚枅鈻堚枅鈻堚枅    鈻堚枅鈻堚枅  鈻堚枅鈻堚枅  
  478.   鈻堚枅      鈻堚枅  鈻堚枅鈻堚枅  鈻堚枅      鈻堚枅            鈻堚枅  鈻堚枅  
  479. 鈻堚枅鈻堚枅鈻堚枅鈻堚枅鈻堚枅鈻堚枅鈻堚枅鈻堚枅      鈻堚枅          鈻堚枅鈻堚枅鈻堚枅    鈻堚枅  鈻堚枅
  480.               鈻堚枅鈻堚枅    鈻堚枅鈻堚枅鈻堚枅鈻堚枅鈻堚枅  鈻堚枅  鈻堚枅    鈻堚枅鈻堚枅  
  481.   鈻堚枅鈻堚枅鈻堚枅鈻堚枅鈻堚枅  鈻堚枅      鈻堚枅  鈻堚枅  鈻堚枅  鈻堚枅鈻堚枅鈻堚枅    鈻堚枅   
  482.   鈻堚枅      鈻堚枅  鈻堚枅  鈻堚枅  鈻堚枅鈻堚枅                鈻堚枅  鈻堚枅鈻堚枅
  483.   鈻堚枅      鈻堚枅  鈻堚枅  鈻堚枅      鈻堚枅鈻堚枅鈻堚枅鈻堚枅    鈻堚枅    鈻堚枅   
  484.   鈻堚枅      鈻堚枅  鈻堚枅  鈻堚枅  鈻堚枅鈻堚枅    鈻堚枅鈻堚枅鈻堚枅鈻堚枅  鈻堚枅  鈻堚枅鈻堚枅  
  485.   鈻堚枅鈻堚枅鈻堚枅鈻堚枅鈻堚枅  鈻堚枅鈻堚枅鈻堚枅鈻堚枅鈻堚枅  鈻堚枅鈻堚枅        鈻堚枅鈻堚枅  鈻堚枅鈻堚枅  
  486.               鈻堚枅    鈻堚枅  鈻堚枅  鈻堚枅鈻堚枅鈻堚枅    鈻堚枅鈻堚枅鈻堚枅      
  487. ydc_n1_1.1.2
  488. 0110000a789eeb3de49609f91 login:
复制代码



我的恩山、我的无线 The best wifi forum is right here.
发表于 2020-8-31 22:36 | 显示全部楼层
小雷盒子         
我的恩山、我的无线 The best wifi forum is right here.
 楼主| 发表于 2020-8-31 22:38 | 显示全部楼层
paldier 发表于 2020-8-31 22:36
小雷盒子

谢谢大神指点!这东西怎么用啊?
来自安卓客户端来自安卓客户端
我的恩山、我的无线 The best wifi forum is right here.
 楼主| 发表于 2020-8-31 22:40 | 显示全部楼层
接显示器是这个。带个二维码。。
224009tgo0a7rheo1rc7fa.jpg

点评

添加微信公众号,扫面屏幕的二维码,教程: https://mp.weixin.qq.com/s/sJtj9oX-vDEHvu04DQnjCA  详情 回复 发表于 2020-8-31 22:51
来自安卓客户端来自安卓客户端
我的恩山、我的无线 The best wifi forum is right here.
发表于 2020-8-31 22:51 | 显示全部楼层
cynizy 发表于 2020-8-31 22:40
接显示器是这个。带个二维码。。

添加微信公众号,扫面屏幕的二维码,教程:
https://mp.weixin.qq.com/s/sJtj9oX-vDEHvu04DQnjCA
我的恩山、我的无线 The best wifi forum is right here.
 楼主| 发表于 2020-8-31 23:17 | 显示全部楼层
jjit 发表于 2020-8-31 22:51
添加微信公众号,扫面屏幕的二维码,教程:
https://mp.weixin.qq.com/s/sJtj9oX-vDEHvu04DQnjCA

谢谢大神指点!!
来自安卓客户端来自安卓客户端
我的恩山、我的无线 The best wifi forum is right here.
您需要登录后才可以回帖 登录 | 立即注册

本版积分规则

QQ|手机版|小黑屋|Archiver|恩山无线论坛(常州市恩山计算机开发有限公司版权所有) ( 苏ICP备05084872号 )|网站地图

GMT+8, 2020-9-26 02:56

Powered by Discuz! X3.4

Copyright © 2001-2020, Tencent Cloud.

快速回复 返回顶部 返回列表