|
|
本帖最后由 qq253044370 于 2019-1-13 23:34 编辑
刷的L大的。自己编译的。极路由B70
本来一直好好的。就是重启了一下路由，就搜不到wifi了。无线是开着的。删除掉重新添加。也不行。
然后甚至按照网上的方法 读取eeprom.bin 里面也能看到mac地址。和别人提供的B70eeprom对比了一下。mac地址并不是FF。
然后进breed里看 mac地址也都对。
但是就是搜不到wifi。有线可以正常用。
内核日志 有个这个错误mt7603e 0000:01:00.0: MCU message 8 (seq 8) timed out 这不是驱动没有加载？？
[ 0.000000] Linux version 4.14.91 (ricky@DESKTOP-IKOQ856) (gcc version 7.4.0 (OpenWrt GCC 7.4.0 r1148-c466387e)) #0 SMP Fri Jan 11 04:23:52 2019
[ 0.000000] SoC Type: MediaTek MT7621 ver:1 eco:3
[ 0.000000] bootconsole [early0] enabled
[ 0.000000] CPU0 revision is: 0001992f (MIPS 1004Kc)
[ 0.000000] MIPS: machine is HiWiFi HC5962
[ 0.000000] Determined physical RAM map:
[ 0.000000] memory: 10000000 @ 00000000 (usable)
[ 0.000000] Initrd not found or empty - disabling initrd
[ 0.000000] VPE topology {2,2} total 4
[ 0.000000] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes.
[ 0.000000] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
[ 0.000000] MIPS secondary cache 256kB, 8-way, linesize 32 bytes.
[ 0.000000] Zone ranges:
[ 0.000000] Normal [mem 0x0000000000000000-0x000000000fffffff]
[ 0.000000] HighMem empty
[ 0.000000] Movable zone start for each node
[ 0.000000] Early memory node ranges
[ 0.000000] node 0: [mem 0x0000000000000000-0x000000000fffffff]
[ 0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x000000000fffffff]
[ 0.000000] On node 0 totalpages: 65536
[ 0.000000] free_area_init_node: node 0, pgdat 805aa080, node_mem_map 81003000
[ 0.000000] Normal zone: 512 pages used for memmap
[ 0.000000] Normal zone: 0 pages reserved
[ 0.000000] Normal zone: 65536 pages, LIFO batch:15
[ 0.000000] random: get_random_bytes called from start_kernel+0x90/0x4a4 with crng_init=0
[ 0.000000] percpu: Embedded 14 pages/cpu @81210000 s26704 r8192 d22448 u57344
[ 0.000000] pcpu-alloc: s26704 r8192 d22448 u57344 alloc=14*4096
[ 0.000000] pcpu-alloc: [0] 0 [0] 1 [0] 2 [0] 3
[ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 65024
[ 0.000000] Kernel command line: console=ttyS0,115200 rootfstype=squashfs,jffs2
[ 0.000000] PID hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.000000] Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
[ 0.000000] Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
[ 0.000000] Writing ErrCtl register=00005b30
[ 0.000000] Readback ErrCtl register=00005b30
[ 0.000000] Memory: 253236K/262144K available (4560K kernel code, 231K rwdata, 1008K rodata, 268K init, 248K bss, 8908K reserved, 0K cma-reserved, 0K highmem)
[ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=4, Nodes=1
[ 0.000000] Hierarchical RCU implementation.
[ 0.000000] NR_IRQS: 256
[ 0.000000] CPU Clock: 880MHz
[ 0.000000] clocksource: GIC: mask: 0xffffffffffffffff max_cycles: 0xcaf478abb4, max_idle_ns: 440795247997 ns
[ 0.000000] clocksource: MIPS: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 4343773742 ns
[ 0.000009] sched_clock: 32 bits at 440MHz, resolution 2ns, wraps every 4880645118ns
[ 0.007805] Calibrating delay loop... 586.13 BogoMIPS (lpj=2930688)
[ 0.073976] pid_max: default: 32768 minimum: 301
[ 0.078744] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.085253] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.094023] Hierarchical SRCU implementation.
[ 0.099166] smp: Bringing up secondary CPUs ...
[ 9.134811] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes.
[ 9.134820] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
[ 9.134832] MIPS secondary cache 256kB, 8-way, linesize 32 bytes.
[ 9.134968] CPU1 revision is: 0001992f (MIPS 1004Kc)
[ 0.163910] Synchronize counters for CPU 1: done.
[ 9.165748] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes.
[ 9.165756] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
[ 9.165766] MIPS secondary cache 256kB, 8-way, linesize 32 bytes.
[ 9.165839] CPU2 revision is: 0001992f (MIPS 1004Kc)
[ 0.255004] Synchronize counters for CPU 2: done.
[ 9.255043] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes.
[ 9.255050] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
[ 9.255059] MIPS secondary cache 256kB, 8-way, linesize 32 bytes.
[ 9.255140] CPU3 revision is: 0001992f (MIPS 1004Kc)
[ 0.340181] Synchronize counters for CPU 3: done.
[ 0.370042] smp: Brought up 1 node, 4 CPUs
[ 0.377813] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[ 0.387597] futex hash table entries: 1024 (order: 3, 32768 bytes)
[ 0.393892] pinctrl core: initialized pinctrl subsystem
[ 0.400474] NET: Registered protocol family 16
[ 0.414291] FPU Affinity set after 11720 emulations
[ 0.415774] pull PCIe RST: RALINK_RSTCTRL = 0
[ 0.720429] release PCIe RST: RALINK_RSTCTRL = 7000000
[ 0.725478] ***** Xtal 40MHz *****
[ 0.728832] release PCIe RST: RALINK_RSTCTRL = 7000000
[ 0.733930] Port 0 N_FTS = 1b105000
[ 0.737397] Port 1 N_FTS = 1b105000
[ 0.740843] Port 2 N_FTS = 1b102800
[ 1.895843] PCIE2 no card, disable it(RST&CLK)
[ 1.900204] -> 21007f2
[ 1.902610] PCIE0 enabled
[ 1.905199] PCIE1 enabled
[ 1.907803] PCI host bridge /pcie@1e140000 ranges:
[ 1.912577] MEM 0x0000000060000000..0x000000006fffffff
[ 1.917732] IO 0x000000001e160000..0x000000001e16ffff
[ 1.922936] PCI coherence region base: 0xbfbf8000, mask/settings: 0x60000000
[ 1.938507] mt7621_gpio 1e000600.gpio: registering 32 gpios
[ 1.944322] mt7621_gpio 1e000600.gpio: registering 32 gpios
[ 1.950010] mt7621_gpio 1e000600.gpio: registering 32 gpios
[ 1.957053] PCI host bridge to bus 0000:00
[ 1.961077] pci_bus 0000:00: root bus resource [mem 0x60000000-0x6fffffff]
[ 1.967937] pci_bus 0000:00: root bus resource [io 0xffffffff]
[ 1.973768] pci_bus 0000:00: root bus resource [??? 0x00000000 flags 0x0]
[ 1.980524] pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff]
[ 1.988416] pci 0000:00:00.0: [0e8d:0801] type 01 class 0x060400
[ 1.988455] pci 0000:00:00.0: reg 0x10: [mem 0x00000000-0x7fffffff]
[ 1.988468] pci 0000:00:00.0: reg 0x14: [mem 0x60300000-0x6030ffff]
[ 1.988529] pci 0000:00:00.0: supports D1
[ 1.988538] pci 0000:00:00.0: PME# supported from D0 D1 D3hot
[ 1.988756] pci 0000:00:01.0: [0e8d:0801] type 01 class 0x060400
[ 1.988782] pci 0000:00:01.0: reg 0x10: [mem 0x00000000-0x7fffffff]
[ 1.988795] pci 0000:00:01.0: reg 0x14: [mem 0x60310000-0x6031ffff]
[ 1.988845] pci 0000:00:01.0: supports D1
[ 1.988853] pci 0000:00:01.0: PME# supported from D0 D1 D3hot
[ 1.989221] pci 0000:01:00.0: [14c3:7603] type 00 class 0x028000
[ 1.989263] pci 0000:01:00.0: reg 0x10: [mem 0x00000000-0x000fffff]
[ 1.989388] pci 0000:01:00.0: PME# supported from D0 D3hot D3cold
[ 1.989567] pci_bus 0000:01: busn_res: [bus 01-ff] end is updated to 01
[ 1.989741] pci 0000:02:00.0: [14c3:7662] type 00 class 0x028000
[ 1.989791] pci 0000:02:00.0: reg 0x10: [mem 0x00000000-0x000fffff 64bit]
[ 1.989836] pci 0000:02:00.0: reg 0x30: [mem 0x00000000-0x0000ffff pref]
[ 1.989926] pci 0000:02:00.0: PME# supported from D0 D3hot D3cold
[ 1.990103] pci_bus 0000:02: busn_res: [bus 02-ff] end is updated to 02
[ 1.990120] pci_bus 0000:00: busn_res: [bus 00-ff] end is updated to 02
[ 1.990176] pci 0000:00:00.0: BAR 0: no space for [mem size 0x80000000]
[ 1.996719] pci 0000:00:00.0: BAR 0: failed to assign [mem size 0x80000000]
[ 2.003599] pci 0000:00:01.0: BAR 0: no space for [mem size 0x80000000]
[ 2.010190] pci 0000:00:01.0: BAR 0: failed to assign [mem size 0x80000000]
[ 2.017085] pci 0000:00:00.0: BAR 8: assigned [mem 0x60000000-0x600fffff]
[ 2.023833] pci 0000:00:01.0: BAR 8: assigned [mem 0x60100000-0x601fffff]
[ 2.030554] pci 0000:00:01.0: BAR 9: assigned [mem 0x60200000-0x602fffff pref]
[ 2.037743] pci 0000:00:00.0: BAR 1: assigned [mem 0x60300000-0x6030ffff]
[ 2.044477] pci 0000:00:01.0: BAR 1: assigned [mem 0x60310000-0x6031ffff]
[ 2.051235] pci 0000:01:00.0: BAR 0: assigned [mem 0x60000000-0x600fffff]
[ 2.057949] pci 0000:00:00.0: PCI bridge to [bus 01]
[ 2.062892] pci 0000:00:00.0: bridge window [mem 0x60000000-0x600fffff]
[ 2.069621] pci 0000:02:00.0: BAR 0: assigned [mem 0x60100000-0x601fffff 64bit]
[ 2.076893] pci 0000:02:00.0: BAR 6: assigned [mem 0x60200000-0x6020ffff pref]
[ 2.084034] pci 0000:00:01.0: PCI bridge to [bus 02]
[ 2.088978] pci 0000:00:01.0: bridge window [mem 0x60100000-0x601fffff]
[ 2.095704] pci 0000:00:01.0: bridge window [mem 0x60200000-0x602fffff pref]
[ 2.104180] clocksource: Switched to clocksource GIC
[ 2.110387] NET: Registered protocol family 2
[ 2.115456] TCP established hash table entries: 2048 (order: 1, 8192 bytes)
[ 2.122342] TCP bind hash table entries: 2048 (order: 2, 16384 bytes)
[ 2.128785] TCP: Hash tables configured (established 2048 bind 2048)
[ 2.135195] UDP hash table entries: 256 (order: 1, 8192 bytes)
[ 2.140963] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes)
[ 2.147446] NET: Registered protocol family 1
[ 2.151763] PCI: CLS 0 bytes, default 32
[ 2.384137] 4 CPUs re-calibrate udelay(lpj = 2924544)
[ 2.390342] Crashlog allocated RAM at address 0x3f00000
[ 2.395733] workingset: timestamp_bits=30 max_order=16 bucket_order=0
[ 2.407908] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 2.413649] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[ 2.425927] random: fast init done
[ 2.429970] io scheduler noop registered
[ 2.433795] io scheduler deadline registered (default)
[ 2.439778] Serial: 8250/16550 driver, 3 ports, IRQ sharing disabled
[ 2.447333] console [ttyS0] disabled
[ 2.450869] 1e000c00.uartlite: ttyS0 at MMIO 0x1e000c00 (irq = 18, base_baud = 3125000) is a 16550A
[ 2.459910] console [ttyS0] enabled
[ 2.466819] bootconsole [early0] disabled
[ 2.475526] cacheinfo: Unable to detect cache hierarchy for CPU 0
[ 2.482221] MediaTek Nand driver init, version v2.1 Fix AHB virt2phys error
[ 2.489348] Enable NFI Clock
[ 2.492219] # MTK NAND # : Use HW ECC
[ 2.495921] Device found in MTK table, ID: c8d1, EXT_ID: 809540
[ 2.501818] Support this Device in MTK table! c8d1
[ 2.506789] [NAND]select ecc bit:4, sparesize :64 spare_per_sector=16
[ 2.513245] nand: device found, Manufacturer ID: 0xc8, Chip ID: 0xd1
[ 2.519581] nand: ESMT NAND 128MiB 3,3V 8-bit
[ 2.523919] nand: 128 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 64
[ 2.531479] Scanning device for bad blocks
[ 2.678201] 12 fixed-partitions partitions found on MTD device MT7621-NAND
[ 2.685056] Creating 12 MTD partitions on "MT7621-NAND":
[ 2.690350] 0x000000000000-0x000000080000 : "u-boot"
[ 2.696235] 0x000000080000-0x000000100000 : "debug"
[ 2.701945] 0x000000100000-0x000000140000 : "factory"
[ 2.707863] 0x000000140000-0x000000340000 : "kernel"
[ 2.713612] 0x000000340000-0x000002140000 : "ubi"
[ 2.719388] 0x000002140000-0x0000021c0000 : "hw_panic"
[ 2.725370] 0x0000021c0000-0x000002240000 : "bdinfo"
[ 2.731134] 0x000002240000-0x0000022c0000 : "backup"
[ 2.736977] 0x0000022c0000-0x0000032c0000 : "overly"
[ 2.742835] 0x0000032c0000-0x0000052c0000 : "firmware_backup"
[ 2.749702] 0x0000052c0000-0x0000054c0000 : "oem"
[ 2.755290] 0x0000054c0000-0x000007f80000 : "opt"
[ 2.761145] [mtk_nand] probe successfully!
[ 2.765972] Signature matched and data read!
[ 2.770220] load_fact_bbt success 1023
[ 2.774623] libphy: Fixed MDIO Bus: probed
[ 2.845959] mtk_soc_eth 1e100000.ethernet: generated random MAC address 46:fd:09:90:14:23
[ 2.854310] libphy: mdio: probed
[ 4.257078] mtk_soc_eth 1e100000.ethernet: loaded mt7530 driver
[ 4.263624] mtk_soc_eth 1e100000.ethernet eth0: mediatek frame engine at 0xbe100000, irq 20
[ 4.273945] NET: Registered protocol family 10
[ 4.279719] Segment Routing with IPv6
[ 4.283450] NET: Registered protocol family 17
[ 4.287960] 8021q: 802.1Q VLAN Support v1.8
[ 4.294973] UBI: auto-attach mtd4
[ 4.298298] ubi0: attaching mtd4
[ 4.579544] ubi0: scanning is finished
[ 4.598381] ubi0: attached mtd4 (name "ubi", size 30 MiB)
[ 4.603768] ubi0: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes
[ 4.610628] ubi0: min./max. I/O unit sizes: 2048/2048, sub-page size 2048
[ 4.617397] ubi0: VID header offset: 2048 (aligned 2048), data offset: 4096
[ 4.624338] ubi0: good PEBs: 240, bad PEBs: 0, corrupted PEBs: 0
[ 4.630314] ubi0: user volume: 2, internal volumes: 1, max. volumes count: 128
[ 4.637515] ubi0: max/mean erase counter: 2/0, WL threshold: 4096, image sequence number: 1084714366
[ 4.646616] ubi0: available PEBs: 0, total reserved PEBs: 240, PEBs reserved for bad PEB handling: 20
[ 4.655824] ubi0: background thread "ubi_bgt0d" started, PID 377
[ 4.657474] block ubiblock0_0: created from ubi0:0(rootfs)
[ 4.667291] ubiblock: device ubiblock0_0 (rootfs) set to be root filesystem
[ 4.674248] hctosys: unable to open rtc device (rtc0)
[ 4.686866] VFS: Mounted root (squashfs filesystem) readonly on device 254:0.
[ 4.694711] Freeing unused kernel memory: 268K
[ 4.699150] This architecture does not have kernel memory protection.
[ 5.177115] init: Console is alive
[ 5.180743] init: - watchdog -
[ 5.205414] mtk_soc_eth 1e100000.ethernet eth0: port 4 link up
[ 5.898618] mtk_soc_eth 1e100000.ethernet eth0: port 1 link up
[ 6.071704] kmodloader: loading kernel modules from /etc/modules-boot.d/*
[ 6.124805] usbcore: registered new interface driver usbfs
[ 6.130355] usbcore: registered new interface driver hub
[ 6.135812] usbcore: registered new device driver usb
[ 6.150583] xhci-mtk 1e1c0000.xhci: 1e1c0000.xhci supply vbus not found, using dummy regulator
[ 6.159331] xhci-mtk 1e1c0000.xhci: 1e1c0000.xhci supply vusb33 not found, using dummy regulator
[ 6.168264] xhci-mtk 1e1c0000.xhci: xHCI Host Controller
[ 6.173602] xhci-mtk 1e1c0000.xhci: new USB bus registered, assigned bus number 1
[ 6.184327] xhci-mtk 1e1c0000.xhci: hcc params 0x01401198 hci version 0x96 quirks 0x0000000000210010
[ 6.193495] xhci-mtk 1e1c0000.xhci: irq 19, io mem 0x1e1c0000
[ 6.200201] hub 1-0:1.0: USB hub found
[ 6.204021] hub 1-0:1.0: 2 ports detected
[ 6.208611] xhci-mtk 1e1c0000.xhci: xHCI Host Controller
[ 6.213918] xhci-mtk 1e1c0000.xhci: new USB bus registered, assigned bus number 2
[ 6.221424] xhci-mtk 1e1c0000.xhci: Host supports USB 3.0 SuperSpeed
[ 6.228027] usb usb2: We don't know the algorithms for LPM for this host, disabling LPM.
[ 6.236949] hub 2-0:1.0: USB hub found
[ 6.240757] hub 2-0:1.0: 1 port detected
[ 6.247301] kmodloader: done loading kernel modules from /etc/modules-boot.d/*
[ 6.264501] init: - preinit -
[ 7.336770] mtk_soc_eth 1e100000.ethernet: PPE started
[ 7.415928] random: procd: uninitialized urandom read (4 bytes read)
[ 10.515799] mount_root: loading kmods from internal overlay
[ 10.549839] kmodloader: loading kernel modules from //etc/modules-boot.d/*
[ 10.564758] kmodloader: done loading kernel modules from //etc/modules-boot.d/*
[ 10.910407] UBIFS (ubi0:1): background thread "ubifs_bgt0_1" started, PID 477
[ 10.983810] UBIFS (ubi0:1): recovery needed
[ 11.179574] UBIFS (ubi0:1): recovery completed
[ 11.184203] UBIFS (ubi0:1): UBIFS: mounted UBI device 0, volume 1, name "rootfs_data"
[ 11.192000] UBIFS (ubi0:1): LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes
[ 11.201895] UBIFS (ubi0:1): FS size: 7110656 bytes (6 MiB, 56 LEBs), journal size 1015809 bytes (0 MiB, 6 LEBs)
[ 11.211950] UBIFS (ubi0:1): reserved for root: 335853 bytes (327 KiB)
[ 11.218378] UBIFS (ubi0:1): media format: w4/r0 (latest is w5/r0), UUID F3DD9FD9-9766-49A8-B4F4-AE1CDF717759, small LPT model
[ 11.232366] block: attempting to load /tmp/ubifs_cfg/upper/etc/config/fstab
[ 11.248839] block: extroot: not configured
[ 11.294415] UBIFS (ubi0:1): un-mount UBI device 0
[ 11.299127] UBIFS (ubi0:1): background thread "ubifs_bgt0_1" stops
[ 11.311085] UBIFS (ubi0:1): background thread "ubifs_bgt0_1" started, PID 480
[ 11.450357] UBIFS (ubi0:1): UBIFS: mounted UBI device 0, volume 1, name "rootfs_data"
[ 11.458204] UBIFS (ubi0:1): LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes
[ 11.468086] UBIFS (ubi0:1): FS size: 7110656 bytes (6 MiB, 56 LEBs), journal size 1015809 bytes (0 MiB, 6 LEBs)
[ 11.478137] UBIFS (ubi0:1): reserved for root: 335853 bytes (327 KiB)
[ 11.484564] UBIFS (ubi0:1): media format: w4/r0 (latest is w5/r0), UUID F3DD9FD9-9766-49A8-B4F4-AE1CDF717759, small LPT model
[ 11.502745] mount_root: loading kmods from internal overlay
[ 11.534331] kmodloader: loading kernel modules from /tmp/overlay/upper/etc/modules-boot.d/*
[ 11.558871] kmodloader: done loading kernel modules from /tmp/overlay/upper/etc/modules-boot.d/*
[ 11.794093] block: attempting to load /tmp/ubifs_cfg/upper/etc/config/fstab
[ 11.805846] block: extroot: not configured
[ 11.846935] mount_root: switching to ubifs overlay
[ 11.887985] urandom-seed: Seeding with /etc/urandom.seed
[ 11.986912] mtk_soc_eth 1e100000.ethernet: 0x100 = 0x6060000c, 0x10c = 0x80818
[ 12.005405] procd: - early -
[ 12.008384] procd: - watchdog -
[ 12.674358] procd: - watchdog -
[ 12.677797] procd: - ubus -
[ 12.770253] random: ubusd: uninitialized urandom read (4 bytes read)
[ 12.874973] random: ubusd: uninitialized urandom read (4 bytes read)
[ 12.881790] random: ubusd: uninitialized urandom read (4 bytes read)
[ 12.889069] procd: - init -
[ 13.477479] kmodloader: loading kernel modules from /etc/modules.d/*
[ 13.516228] gre: GRE over IPv4 demultiplexor driver
[ 13.522989] ip_gre: GRE over IPv4 tunneling driver
[ 13.535599] ip6_tables: (C) 2000-2006 Netfilter Core Team
[ 13.548527] Netfilter messages via NETLINK v0.30.
[ 13.555265] ip_set: protocol 6
[ 13.595646] u32 classifier
[ 13.598369] input device check on
[ 13.602013] Actions configured
[ 13.607622] Mirror/redirect action on
[ 13.623245] nf_conntrack version 0.5.0 (4096 buckets, 16384 max)
[ 13.637225] Loading modules backported from Linux version v4.19.7-0-g61c68f2a2af0
[ 13.644767] Backport generated by backports.git v4.19.7-1-0-g148b072d
[ 13.654770] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 13.707795] ctnetlink v0.93: registering with nfnetlink.
[ 13.786832] usbcore: registered new interface driver usblp
[ 13.799864] wireguard: WireGuard 0.0.20181218 loaded. See www.wireguard.com for information.
[ 13.808403] wireguard: Copyright (C) 2015-2018 Jason A. Donenfeld <Jason@zx2c4.com>. All Rights Reserved.
[ 13.854765] xt_time: kernel timezone is -0000
[ 13.936076] bus=0x1, slot = 0x0, irq=0xff
[ 13.940329] mt7603e 0000:01:00.0: ASIC revision: 76030010
[ 13.980756] mt7603e 0000:01:00.0: Firmware Version: 1
[ 13.985995] mt7603e 0000:01:00.0: Build Time: 20161027164355
[ 14.024289] mt7603e 0000:01:00.0: firmware init done
[ 14.204984] ieee80211 phy0: Selected rate control algorithm 'minstrel_ht'
[ 14.222563] bus=0x2, slot = 0x1, irq=0xff
[ 14.226922] mt76x2e 0000:02:00.0: ASIC revision: 76120044
[ 14.885074] mt76x2e 0000:02:00.0: ROM patch build: 20141115060606a
[ 14.895767] mt76x2e 0000:02:00.0: Firmware Version: 0.0.00
[ 14.901269] mt76x2e 0000:02:00.0: Build: 1
[ 14.905378] mt76x2e 0000:02:00.0: Build Time: 201507311614____
[ 14.934347] mt76x2e 0000:02:00.0: Firmware running!
[ 14.942083] ieee80211 phy1: Selected rate control algorithm 'minstrel_ht'
[ 14.955104] PPP generic driver version 2.4.2
[ 14.961216] PPP MPPE Compression module registered
[ 14.967684] NET: Registered protocol family 24
[ 14.975329] kmodloader: done loading kernel modules from /etc/modules.d/*
[ 15.688169] urandom_read: 5 callbacks suppressed
[ 15.688181] random: jshn: uninitialized urandom read (4 bytes read)
[ 17.422199] xt_FULLCONENAT: RFC3489 Full Cone NAT module
[ 17.422199] xt_FULLCONENAT: Copyright (C) 2018 Chion Tang <tech@chionlab.moe>
[ 17.983053] random: crng init done
[ 25.701345] mtk_soc_eth 1e100000.ethernet: PPE started
[ 25.712878] device eth0 entered promiscuous mode
[ 25.721582] br-lan: port 1(eth0.1) entered blocking state
[ 25.727082] br-lan: port 1(eth0.1) entered disabled state
[ 25.733180] device eth0.1 entered promiscuous mode
[ 25.741148] br-lan: port 1(eth0.1) entered blocking state
[ 25.746589] br-lan: port 1(eth0.1) entered forwarding state
[ 25.753017] IPv6: ADDRCONF(NETDEV_UP): br-lan: link is not ready
[ 26.715262] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready
[ 31.674194] mt7603e 0000:01:00.0: MCU message 8 (seq 8) timed out
[ 31.694438] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 31.706304] br-lan: port 2(wlan0) entered blocking state
[ 31.711659] br-lan: port 2(wlan0) entered disabled state
[ 31.717601] device wlan0 entered promiscuous mode
[ 35.274192] mt7603e 0000:01:00.0: MCU message 8 (seq 9) timed out
[ 35.294443] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
[ 35.301065] br-lan: port 2(wlan0) entered blocking state
[ 35.306411] br-lan: port 2(wlan0) entered forwarding state
|
|
简体中文
繁體中文
English
日本語
Deutsch
한국 사람
بالعربية
TÜRKÇE
português
คนไทย
IP卡
狗仔卡
发表于 2019-1-13 10:22
置顶卡
沉默卡
喧嚣卡
顶贴卡
显身卡