已解决（求助）K2 ttl刷breed最后一步错误，一直卡在loading：TTTT

beiren000

路由器硬件和软件

电脑设置
工具解压到桌面

IP已设置  防火墙也已经关闭  ，退出了360卫士


一直卡在最后一步
K2 ttl刷breed最后一步错误，一直卡在loading：TTTT

不知道问题出现在哪里。求助高手。

解决方案：
之前刷机一直没有将路由器和电脑连接上，所以卡在这一步了。
感谢9楼zhuoling1234大神的指导。
刷breed前将网线连接路由器LAN口至电脑主机！
然后就搞定了！

beiren000

提示代码
U-Boot 1.1.3 ( - )

Board: Ralink APSoC DRAM:  64 MB
MT7620 gpio init : WPS / RESET pin
GPIO#1 updated GPIOMODE register: 001a311c -> 001a311d
relocate_code Pointer at: 83fa4000
enable ephy clock...done. rf reg 29 = 5
SSC disabled.
spi_wait_nsec: 29
spi device id: ef 40 17 0 0 (40170000)
find flash: W25Q64BV
*** Warning - bad CRC, using default environment

============================================
Ralink UBoot Version: 4.3.0.0
--------------------------------------------
ASIC 7620_MP (Port5<->None)
DRAM component: 512 Mbits DDR, width 16
DRAM bus: 16 bit
Total memory: 64 MBytes
Flash component: SPI Flash
Date:  Time:
============================================
icache: sets:512, ways:4, linesz:32 ,total:65536
dcache: sets:256, ways:4, linesz:32 ,total:32768

##### The CPU freq = 580 MHZ ####
estimate memory size =64 Mbytes

Press press hardware button for more than 4 seconds to run web failsafe mode



Catution: hardware button wasn't pressed or not long enough!
Continuing normal boot...


Please choose the operation:
   1: Load system code to SDRAM via TFTP.
   2: Load system code then write to Flash via TFTP.
   3: Boot system code via Flash (default).
   4: Entr boot command line interface.
   6: Load all then write to Flash via TFTP.
   7: Load Boot Loader code then write to Flash via Serial.
   9: Load Boot Loader code then write to Flash via TFTP.

You choosed 9




9: System Load Boot Loader then write to Flash via TFTP.
Warning!! Erase Boot Loader in Flash then burn new one. Are you sure?(Y/N)
Please Input new ones /or Ctrl-C to discard
        Input device IP (192.168.2.1) ==:192.168.2.1
        Input server IP (192.168.2.10) ==:192.168.2.10
        Input Uboot filename () ==:breed.bin

netboot_common, argc= 3

NetTxPacket = 0x83FE6780

KSEG1ADDR(NetTxPacket) = 0xA3FE6780

NetLoop,call eth_halt !

NetLoop,call eth_init !
Trying Eth0 (10/100-M)

Waitting for RX_DMA_BUSY status Start... done


ETH_STATE_ACTIVE!!
TFTP from server 192.168.2.10; our IP address is 192.168.2.1
Filename 'breed.bin'.

TIMEOUT_COUNT=10,Load address: 0x80100000
Loading: T T T T T T T T T T
Retry count exceeded; starting again

ArpTimeoutCheck
TFTP from server 192.168.2.10; our IP address is 192.168.2.1
Filename 'breed.bin'.

TIMEOUT_COUNT=10,Load address: 0x80100000

240038901

TFTP没设置好

beiren000

TFTP   设置图

beiren000

240038901 发表于 2020-11-13 14:11
TFTP没设置好

高手求助，TFTPD 64 我只设置显示192.168.2.10
还有其他的设置吗？

xzw89

tftp重新下载个试试，，，，我之前也是死活刷不了，，换了后正常刷

beiren000

xzw89 发表于 2020-11-13 14:43
tftp重新下载个试试，，，，我之前也是死活刷不了，，换了后正常刷

大神，弱弱的问一下，刷breed的时候需要用网线连接电脑主机吗？

书桩

beiren000 发表于 2020-11-13 15:07
大神，弱弱的问一下，刷breed的时候需要用网线连接电脑主机吗？

网线不连你觉得它是充哪上传的呢？

zhuoling1234

TTT就是网络不通

beiren000

zhuoling1234 发表于 2020-11-13 15:31
TTT就是网络不通

回去再试下

beiren000

zhuoling1234 发表于 2020-11-13 15:31
TTT就是网络不通

连上网线后搞定了！非常感谢。