|
|
基于L大源码来合并双flash的估计我是全网首发吧，固件修改了双flash，由于是尝鲜版，第一次启动全部正常，第二次进系统直接2.4G不能用，5G正常，BUG还未修好，手上有C301的大神可以方便私信我，一起修复这仅有的一个BUG
固件下载地址
https://pzc.lanzous.com/i2ohm2h
附上内核日志，大家可以常考一下
[ 0.000000] Linux version 4.14.195 (pzc@pzc-Manjaro) (gcc version 8.4.0 (OpenWrt GCC 8.4.0 r3053-96f26d716)) #0 Sun Jan 31 06:49:19 2021
[ 0.000000] MyLoader: sysp=40804568, boardp=81008941, parts=022061c1
[ 0.000000] bootconsole [early0] enabled
[ 0.000000] CPU0 revision is: 0001974c (MIPS 74Kc)
[ 0.000000] SoC: Atheros AR9344 rev 3
[ 0.000000] Determined physical RAM map:
[ 0.000000] memory: 08000000 @ 00000000 (usable)
[ 0.000000] Initrd not found or empty - disabling initrd
[ 0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
[ 0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes
[ 0.000000] Zone ranges:
[ 0.000000] Normal [mem 0x0000000000000000-0x0000000007ffffff]
[ 0.000000] Movable zone start for each node
[ 0.000000] Early memory node ranges
[ 0.000000] node 0: [mem 0x0000000000000000-0x0000000007ffffff]
[ 0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x0000000007ffffff]
[ 0.000000] On node 0 totalpages: 32768
[ 0.000000] free_area_init_node: node 0, pgdat 8055de20, node_mem_map 81000020
[ 0.000000] Normal zone: 288 pages used for memmap
[ 0.000000] Normal zone: 0 pages reserved
[ 0.000000] Normal zone: 32768 pages, LIFO batch:7
[ 0.000000] random: get_random_bytes called from start_kernel+0x98/0x4a4 with crng_init=0
[ 0.000000] pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768
[ 0.000000] pcpu-alloc: [0] 0
[ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 32480
[ 0.000000] Kernel command line: board=QIHOO-C301 mtdparts=flash:256k(u-boot),64k(u-boot-env),64k(devdata),64k(devconf),32256k(firmware),64k(radiocfg) console=ttyS0,115200 rootfstype=squashfs noinitrd
[ 0.000000] PID hash table entries: 512 (order: -1, 2048 bytes)
[ 0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
[ 0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
[ 0.000000] Writing ErrCtl register=00000000
[ 0.000000] Readback ErrCtl register=00000000
[ 0.000000] Memory: 123720K/131072K available (3989K kernel code, 199K rwdata, 928K rodata, 316K init, 209K bss, 7352K reserved, 0K cma-reserved)
[ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[ 0.000000] NR_IRQS: 51
[ 0.000000] Clocks: CPU:700.000MHz, DDR:450.000MHz, AHB:225.000MHz, Ref:40.000MHz
[ 0.000000] clocksource: MIPS: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 5460744132 ns
[ 0.000007] sched_clock: 32 bits at 350MHz, resolution 2ns, wraps every 6135667710ns
[ 0.008691] Calibrating delay loop... 348.97 BogoMIPS (lpj=1744896)
[ 0.075702] pid_max: default: 32768 minimum: 301
[ 0.081092] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.088462] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.098824] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[ 0.109831] futex hash table entries: 256 (order: -1, 3072 bytes)
[ 0.117134] NET: Registered protocol family 16
[ 0.123307] MIPS: machine is Qihoo 360 C301
[ 0.143711] registering PCI controller with io_map_base unset
[ 0.661767] PCI host bridge to bus 0000:00
[ 0.666391] pci_bus 0000:00: root bus resource [mem 0x10000000-0x13ffffff]
[ 0.674054] pci_bus 0000:00: root bus resource [io 0x0000]
[ 0.680271] pci_bus 0000:00: root bus resource [??? 0x00000000 flags 0x0]
[ 0.687835] pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff]
[ 0.696703] pci 0000:00:00.0: [168c:003c] type 00 class 0x028000
[ 0.696764] pci 0000:00:00.0: reg 0x10: [mem 0x10000000-0x101fffff 64bit]
[ 0.696844] pci 0000:00:00.0: reg 0x30: [mem 0x00000000-0x0000ffff pref]
[ 0.696920] pci 0000:00:00.0: supports D1 D2
[ 0.697108] pci_bus 0000:00: busn_res: [bus 00-ff] end is updated to 00
[ 0.697133] pci 0000:00:00.0: BAR 0: assigned [mem 0x10000000-0x101fffff 64bit]
[ 0.705295] pci 0000:00:00.0: BAR 6: assigned [mem 0x10200000-0x1020ffff pref]
[ 0.713461] workqueue: max_active 576 requested for napi_workq is out of range, clamping between 1 and 512
[ 0.726882] clocksource: Switched to clocksource MIPS
[ 0.733502] NET: Registered protocol family 2
[ 0.739071] TCP established hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.746846] TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.753981] TCP: Hash tables configured (established 1024 bind 1024)
[ 0.761195] UDP hash table entries: 256 (order: 0, 4096 bytes)
[ 0.767751] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[ 0.775004] NET: Registered protocol family 1
[ 0.779937] PCI: CLS 0 bytes, default 32
[ 0.783026] Crashlog allocated RAM at address 0x3f00000
[ 0.790193] workingset: timestamp_bits=14 max_order=15 bucket_order=1
[ 0.802520] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 0.809062] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[ 0.830652] io scheduler noop registered
[ 0.835029] io scheduler deadline registered (default)
[ 0.841109] Serial: 8250/16550 driver, 1 ports, IRQ sharing disabled
[ 0.848576] console [ttyS0] disabled
[ 0.872650] serial8250.0: ttyS0 at MMIO 0x18020000 (irq = 11, base_baud = 2500000) is a 16550A
[ 0.882275] console [ttyS0] enabled
[ 0.889696] bootconsole [early0] disabled
[ 0.902390] m25p80 spi0.0: found mx25l12805d, expected m25p80
[ 0.909089] m25p80 spi0.0: mx25l12805d (16384 Kbytes)
[ 0.915318] m25p80 spi0.1: found mx25l12805d, expected m25p80
[ 0.922110] m25p80 spi0.1: mx25l12805d (16384 Kbytes)
[ 0.929079] libphy: Fixed MDIO Bus: probed
[ 0.935588] Concatenating MTD devices:
[ 0.939440] (0): "spi0.0"
[ 0.942095] (1): "spi0.1"
[ 0.944751] into device "flash"
[ 0.947956] 6 cmdlinepart partitions found on MTD device flash
[ 0.953870] Creating 6 MTD partitions on "flash":
[ 0.958659] 0x000000000000-0x000000040000 : "u-boot"
[ 0.983659] libphy: ag71xx_mdio: probed
[ 0.988458] 0x000000040000-0x000000050000 : "u-boot-env"
[ 0.995057] 0x000000050000-0x000000060000 : "devdata"
[ 1.002143] 0x000000060000-0x000000070000 : "devconf"
[ 1.008560] 0x000000070000-0x000001ff0000 : "firmware"
[ 1.128754] 2 seama-fw partitions found on MTD device firmware
[ 1.134687] 0x000000070040-0x000000220000 : "kernel"
[ 1.140407] 0x000000220000-0x000001ff0000 : "rootfs"
[ 1.146023] mtd: device 8 (rootfs) set to be root filesystem
[ 1.151845] 1 squashfs-split partitions found on MTD device rootfs
[ 1.158133] 0x000000940000-0x000001ff0000 : "rootfs_data"
[ 1.166321] 0x000001ff0000-0x000002000000 : "radiocfg"
[ 1.618752] ag71xx-mdio.1: Found an AR934X built-in switch
[ 1.670844] eth0: Atheros AG71xx at 0xba000000, irq 5, mode: gmii
[ 2.308988] ag71xx ag71xx.0: connected to PHY at ag71xx-mdio.1:00 [uid=004dd042, driver=Generic PHY]
[ 2.318783] eth1: Atheros AG71xx at 0xb9000000, irq 4, mode: mii
[ 2.326293] NET: Registered protocol family 10
[ 2.334950] Segment Routing with IPv6
[ 2.338813] NET: Registered protocol family 17
[ 2.343890] 8021q: 802.1Q VLAN Support v1.8
[ 2.359601] VFS: Mounted root (squashfs filesystem) readonly on device 31:8.
[ 2.368096] Freeing unused kernel memory: 316K
[ 2.372606] This architecture does not have kernel memory protection.
[ 2.576926] random: fast init done
[ 2.928492] init: Console is alive
[ 2.932162] init: - watchdog -
[ 4.839928] kmodloader: loading kernel modules from /etc/modules-boot.d/*
[ 4.975356] usbcore: registered new interface driver usbfs
[ 4.981040] usbcore: registered new interface driver hub
[ 4.986506] usbcore: registered new device driver usb
[ 5.007253] ANTFS Module: Version 07.19-b41ba529
[ 5.046184] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 5.061626] SCSI subsystem initialized
[ 5.070633] ehci-platform: EHCI generic platform driver
[ 5.076040] ehci-platform ehci-platform: EHCI Host Controller
[ 5.081942] ehci-platform ehci-platform: new USB bus registered, assigned bus number 1
[ 5.092052] ehci-platform ehci-platform: TX-TX IDP fix enabled
[ 5.098011] ehci-platform ehci-platform: irq 3, io mem 0x1b000000
[ 5.126929] ehci-platform ehci-platform: USB 2.0 started, EHCI 1.00
[ 5.134005] hub 1-0:1.0: USB hub found
[ 5.138262] hub 1-0:1.0: 1 port detected
[ 5.146998] usbcore: registered new interface driver usb-storage
[ 5.155878] usbcore: registered new interface driver uas
[ 5.161869] kmodloader: done loading kernel modules from /etc/modules-boot.d/*
[ 5.179652] init: - preinit -
[ 6.522128] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 6.615911] random: procd: uninitialized urandom read (4 bytes read)
[ 8.668344] eth0: link up (1000Mbps/Full duplex)
[ 8.673062] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[ 10.829855] mount_root: loading kmods from internal overlay
[ 10.886157] kmodloader: loading kernel modules from //etc/modules-boot.d/*
[ 10.897557] kmodloader: done loading kernel modules from //etc/modules-boot.d/*
[ 11.924011] jffs2: notice: (467) jffs2_build_xattr_subsystem: complete building xattr subsystem, 1 of xdatum (0 unchecked, 1 orphan) and 1 of xref (1 dead, 0 orphan) found.
[ 11.940314] block: attempting to load /tmp/jffs_cfg/upper/etc/config/fstab
[ 11.956179] block: extroot: not configured
[ 12.140749] jffs2: notice: (465) jffs2_build_xattr_subsystem: complete building xattr subsystem, 1 of xdatum (0 unchecked, 1 orphan) and 1 of xref (1 dead, 0 orphan) found.
[ 12.159102] mount_root: loading kmods from internal overlay
[ 12.214659] kmodloader: loading kernel modules from /tmp/overlay/upper/etc/modules-boot.d/*
[ 12.226073] kmodloader: done loading kernel modules from /tmp/overlay/upper/etc/modules-boot.d/*
[ 12.940528] block: attempting to load /tmp/jffs_cfg/upper/etc/config/fstab
[ 12.952809] block: extroot: not configured
[ 12.958207] mount_root: switching to jffs2 overlay
[ 13.023081] overlayfs: upper fs does not support tmpfile.
[ 13.034418] urandom-seed: Seeding with /etc/urandom.seed
[ 13.174083] eth0: link down
[ 13.188810] procd: - early -
[ 13.191831] procd: - watchdog -
[ 13.800970] procd: - watchdog -
[ 13.804470] procd: - ubus -
[ 14.035579] random: ubusd: uninitialized urandom read (4 bytes read)
[ 14.116515] random: ubusd: uninitialized urandom read (4 bytes read)
[ 14.130770] random: ubusd: uninitialized urandom read (4 bytes read)
[ 14.146183] procd: - init -
[ 15.222039] urandom_read: 5 callbacks suppressed
[ 15.222046] random: jshn: uninitialized urandom read (4 bytes read)
[ 15.818786] kmodloader: loading kernel modules from /etc/modules.d/*
[ 15.857594] NET: Registered protocol family 38
[ 15.924837] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver
[ 15.954400] ip6_tables: (C) 2000-2006 Netfilter Core Team
[ 15.996693] nf_conntrack version 0.5.0 (2048 buckets, 8192 max)
[ 16.038107] urngd: v1.0.2 started.
[ 16.146642] Netfilter messages via NETLINK v0.30.
[ 16.159805] ip_set: protocol 6
[ 16.247537] cryptodev: driver 1.10 loaded.
[ 16.273706] Loading modules backported from Linux version v5.8.18-0-gab435ce49bd1
[ 16.281347] Backport generated by backports.git v5.8.18-1-0-ga630fd46
[ 16.318710] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 16.333787] random: crng init done
[ 16.481635] ctnetlink v0.93: registering with nfnetlink.
[ 16.690655] usbcore: registered new interface driver ums-alauda
[ 16.718648] usbcore: registered new interface driver ums-cypress
[ 16.728543] usbcore: registered new interface driver ums-datafab
[ 16.758830] usbcore: registered new interface driver ums-freecom
[ 16.782746] usbcore: registered new interface driver ums-isd200
[ 16.808895] usbcore: registered new interface driver ums-jumpshot
[ 16.838622] usbcore: registered new interface driver ums-karma
[ 16.861395] usbcore: registered new interface driver ums-sddr09
[ 16.899681] usbcore: registered new interface driver ums-sddr55
[ 16.921719] usbcore: registered new interface driver ums-usbat
[ 16.990914] xt_time: kernel timezone is -0000
[ 17.296588] PPP generic driver version 2.4.2
[ 17.318321] PPP MPPE Compression module registered
[ 17.325055] NET: Registered protocol family 24
[ 17.420103] pci 0000:00:00.0: using irq 40 for pin 1
[ 17.425155] ath10k 5.8 driver, optimized for CT firmware, probing pci device: 0x3c.
[ 17.473950] ath10k_pci 0000:00:00.0: pci irq legacy oper_irq_mode 1 irq_mode 0 reset_mode 0
[ 17.798035] ath10k_pci 0000:00:00.0: Direct firmware load for ath10k/fwcfg-pci-0000:00:00.0.txt failed with error -2
[ 17.808763] ath10k_pci 0000:00:00.0: Falling back to user helper
[ 25.793104] firmware ath10k!fwcfg-pci-0000:00:00.0.txt: firmware_loading_store: map pages failed
[ 25.805050] ath10k_pci 0000:00:00.0: Direct firmware load for ath10k/pre-cal-pci-0000:00:00.0.bin failed with error -2
[ 25.815955] ath10k_pci 0000:00:00.0: Falling back to user helper
[ 26.042283] firmware ath10k!pre-cal-pci-0000:00:00.0.bin: firmware_loading_store: map pages failed
[ 26.053221] ath10k_pci 0000:00:00.0: Direct firmware load for ath10k/QCA988X/hw2.0/ct-firmware-5.bin failed with error -2
[ 26.064387] ath10k_pci 0000:00:00.0: Falling back to user helper
[ 26.291750] firmware ath10k!QCA988X!hw2.0!ct-firmware-5.bin: firmware_loading_store: map pages failed
[ 26.301418] ath10k_pci 0000:00:00.0: Direct firmware load for ath10k/QCA988X/hw2.0/ct-firmware-2.bin failed with error -2
[ 26.312585] ath10k_pci 0000:00:00.0: Falling back to user helper
[ 26.540237] firmware ath10k!QCA988X!hw2.0!ct-firmware-2.bin: firmware_loading_store: map pages failed
[ 26.549903] ath10k_pci 0000:00:00.0: Direct firmware load for ath10k/QCA988X/hw2.0/firmware-6.bin failed with error -2
[ 26.560794] ath10k_pci 0000:00:00.0: Falling back to user helper
[ 26.787207] firmware ath10k!QCA988X!hw2.0!firmware-6.bin: firmware_loading_store: map pages failed
[ 26.796557] ath10k_pci 0000:00:00.0: Direct firmware load for ath10k/QCA988X/hw2.0/firmware-5.bin failed with error -2
[ 26.807449] ath10k_pci 0000:00:00.0: Falling back to user helper
[ 27.033505] firmware ath10k!QCA988X!hw2.0!firmware-5.bin: firmware_loading_store: map pages failed
[ 27.042910] ath10k_pci 0000:00:00.0: Direct firmware load for ath10k/QCA988X/hw2.0/firmware-4.bin failed with error -2
[ 27.053797] ath10k_pci 0000:00:00.0: Falling back to user helper
[ 27.279868] firmware ath10k!QCA988X!hw2.0!firmware-4.bin: firmware_loading_store: map pages failed
[ 27.289273] ath10k_pci 0000:00:00.0: Direct firmware load for ath10k/QCA988X/hw2.0/firmware-3.bin failed with error -2
[ 27.300160] ath10k_pci 0000:00:00.0: Falling back to user helper
[ 27.526436] firmware ath10k!QCA988X!hw2.0!firmware-3.bin: firmware_loading_store: map pages failed
[ 27.540918] ath10k_pci 0000:00:00.0: qca988x hw2.0 target 0x4100016c chip_id 0x043222ff sub 168c:3223
[ 27.550336] ath10k_pci 0000:00:00.0: kconfig debug 0 debugfs 1 tracing 0 dfs 1 testmode 0
[ 27.562763] ath10k_pci 0000:00:00.0: firmware ver 10.1-ct-8x-__fW-022-ecad3248 api 2 features wmi-10.x,has-wmi-mgmt-tx,mfp,txstatus-noack,wmi-10.x-CT,ratemask-CT,txrate-CT,get-temp-CT,tx-rc-CT,cust-stats-CT,retry-gt2-CT,txrate2-CT,beacon-cb-CT,wmi-block-ack-CT crc32 3e4cf97f
[ 27.671039] ath10k_pci 0000:00:00.0: Direct firmware load for ath10k/QCA988X/hw2.0/board-2.bin failed with error -2
[ 27.681688] ath10k_pci 0000:00:00.0: Falling back to user helper
[ 27.842642] firmware ath10k!QCA988X!hw2.0!board-2.bin: firmware_loading_store: map pages failed
[ 27.851995] ath10k_pci 0000:00:00.0: board_file api 1 bmi_id N/A crc32 bebc7c08
[ 28.760512] ath10k_pci 0000:00:00.0: 10.1 wmi init: vdevs: 16 peers: 127 tid: 256
[ 28.778316] ath10k_pci 0000:00:00.0: wmi print 'P 128 V 8 T 410'
[ 28.784644] ath10k_pci 0000:00:00.0: wmi print 'msdu-desc: 1424 sw-crypt: 0 ct-sta: 0'
[ 28.792791] ath10k_pci 0000:00:00.0: wmi print 'alloc rem: 24984 iram: 38672'
[ 28.849599] ath10k_pci 0000:00:00.0: htt-ver 2.1 wmi-op 2 htt-op 2 cal file max-sta 128 raw 0 hwcrypto 1
[ 28.864820] ath10k_pci 0000:00:00.0: NOTE: Firmware DBGLOG output disabled in debug_mask: 0x10000000
[ 29.000405] ath: EEPROM regdomain sanitized
[ 29.000416] ath: EEPROM regdomain: 0x64
[ 29.000420] ath: EEPROM indicates we should expect a direct regpair map
[ 29.000440] ath: Country alpha2 being used: 00
[ 29.000443] ath: Regpair used: 0x64
[ 29.136363] ath: phy1: Unable to initialize hardware; initialization status: -5
[ 29.143848] ath9k ar934x_wmac: failed to initialize device
[ 29.149476] ath9k: probe of ar934x_wmac failed with error -5
[ 29.157129] kmodloader: done loading kernel modules from /etc/modules.d/*
[ 39.279569] jffs2: notice: (1641) jffs2_build_xattr_subsystem: complete building xattr subsystem, 2 of xdatum (0 unchecked, 2 orphan) and 2 of xref (2 dead, 0 orphan) found.
[ 39.320169] jffs2: Too few erase blocks (1)
[ 42.735979] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 42.758855] br-lan: port 1(eth0.1) entered blocking state
[ 42.764341] br-lan: port 1(eth0.1) entered disabled state
[ 42.770139] device eth0.1 entered promiscuous mode
[ 42.775002] device eth0 entered promiscuous mode
[ 42.824477] IPv6: ADDRCONF(NETDEV_UP): br-lan: link is not ready
[ 42.872733] IPv6: ADDRCONF(NETDEV_UP): eth1: link is not ready
[ 44.368385] eth0: link up (1000Mbps/Full duplex)
[ 44.416981] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[ 44.490053] br-lan: port 1(eth0.1) entered blocking state
[ 44.495541] br-lan: port 1(eth0.1) entered forwarding state
[ 44.593428] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready
[ 46.246185] ath: EEPROM regdomain: 0x8348
[ 46.246193] ath: EEPROM indicates we should expect a country code
[ 46.246200] ath: doing EEPROM country->regdmn map search
[ 46.246207] ath: country maps to regdmn code: 0x3a
[ 46.246212] ath: Country alpha2 being used: US
[ 46.246216] ath: Regpair used: 0x3a
[ 46.246222] ath: regdomain 0x8348 dynamically updated by user
[ 49.366629] fast-classifier (PBR safe v2.1.4a): starting up
[ 49.372514] fast-classifier: registered
[ 51.456323] ath10k_pci 0000:00:00.0: 10.1 wmi init: vdevs: 16 peers: 127 tid: 256
[ 51.474155] ath10k_pci 0000:00:00.0: wmi print 'P 128 V 8 T 410'
[ 51.480314] ath10k_pci 0000:00:00.0: wmi print 'msdu-desc: 1424 sw-crypt: 0 ct-sta: 0'
[ 51.489324] ath10k_pci 0000:00:00.0: wmi print 'alloc rem: 24984 iram: 38672'
[ 51.616011] ath10k_pci 0000:00:00.0: pdev param 0 not supported by firmware
[ 51.637523] ath10k_pci 0000:00:00.0: rts threshold -1
[ 51.648195] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 51.718242] br-lan: port 2(wlan0) entered blocking state
[ 51.723638] br-lan: port 2(wlan0) entered disabled state
[ 51.729364] device wlan0 entered promiscuous mode
[ 53.277541] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
[ 53.284152] br-lan: port 2(wlan0) entered blocking state
[ 53.289600] br-lan: port 2(wlan0) entered forwarding state
[ 135.691405] device wlan0 left promiscuous mode
[ 135.696026] br-lan: port 2(wlan0) entered disabled state
[ 135.977645] eth0: link down
[ 135.992467] br-lan: port 1(eth0.1) entered disabled state
[ 136.214787] ath10k_pci 0000:00:00.0: mac flush null vif, drop 0 queues 0xffff
[ 137.508385] eth0: link up (1000Mbps/Full duplex)
[ 137.531656] br-lan: port 1(eth0.1) entered blocking state
[ 137.537185] br-lan: port 1(eth0.1) entered forwarding state
[ 141.502952] ath10k_pci 0000:00:00.0: 10.1 wmi init: vdevs: 16 peers: 127 tid: 256
[ 141.520775] ath10k_pci 0000:00:00.0: wmi print 'P 128 V 8 T 410'
[ 141.527258] ath10k_pci 0000:00:00.0: wmi print 'msdu-desc: 1424 sw-crypt: 0 ct-sta: 0'
[ 141.535387] ath10k_pci 0000:00:00.0: wmi print 'alloc rem: 24984 iram: 38672'
[ 141.607654] ath10k_pci 0000:00:00.0: pdev param 0 not supported by firmware
[ 141.622912] ath10k_pci 0000:00:00.0: rts threshold -1
[ 141.628660] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 141.673082] br-lan: port 2(wlan0) entered blocking state
[ 141.678544] br-lan: port 2(wlan0) entered disabled state
[ 141.684210] device wlan0 entered promiscuous mode
[ 144.313085] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
[ 144.319764] br-lan: port 2(wlan0) entered blocking state
[ 144.325161] br-lan: port 2(wlan0) entered forwarding state
|
|
简体中文
繁體中文
English
日本語
Deutsch
한국 사람
بالعربية
TÜRKÇE
português
คนไทย
IP卡
狗仔卡
发表于 2021-2-2 05:33
置顶卡
沉默卡
喧嚣卡
顶贴卡
显身卡
只有我的c301不行？，真的可以我可以编译些插件进去