|
小米路由器3刷回官方变砖了,一直橙色灯,ttll编程器无法选择任何一个选项!12349按哪个都没有反映!通电后ttl编程器就一直循环显示如下代码,无法选择。
- U-Boot 1.1.3 (Apr 15 2016 - 17:46:32)
- Board: Ralink APSoC DRAM: 128 MB
- Power on memory test. Memory size= 128 MB...OK!
- relocate_code Pointer at: 87fb8000
- enable ephy clock...done. rf reg 29 = 5
- SSC disabled.
- !!! nand page size = 2048, addr len=4
- ..============================================
- Ralink UBoot Version: 4.2.S.1
- --------------------------------------------
- ASIC 7620_MP (Port5<->None)
- DRAM_CONF_FROM: Auto-detection
- DRAM_TYPE: DDR2
- DRAM component: 1024 Mbits
- DRAM bus: 16 bit
- Total memory: 128 MBytes
- Flash component: NAND Flash
- Date:Apr 15 2016 Time:17:46:32
- ============================================
- icache: sets:512, ways:4, linesz:32 ,total:65536
- dcache: sets:256, ways:4, linesz:32 ,total:32768
- ##### The CPU freq = 580 MHZ ####
- estimate memory size =128 Mbytes
- Please choose the operation:
- 1: Load system code to SDRAM via TFTP.
- 2: Load system code then write to Flash via TFTP.
- 3: Boot system code via Flash (default).
- 4: Entr boot command line interface.
- 9: Load Boot Loader code then write to Flash via TFTP.
- 3: System Boot system code via Flash.
- Booting System 2
- ..ranand_erase_write: offs:40000, count:20000
- .Done!
- done
- ## Booting image at bc600000 ...
- Image Name: MIPS OpenWrt Linux-4.14.89
- Image Type: MIPS Linux Kernel Image (lzma compressed)
- Data Size: 1596367 Bytes = 1.5 MB
- Load Address: 80000000
- Entry Point: 80000000
- ......................... Verifying Checksum ... OK
- Uncompressing Kernel Image ... OK
- commandline uart_en=0 factory_mode=0 mem=128m
- No initrd
- ## Transferring control to Linux (at address 80000000) ...
- ## Giving linux memsize in MB, 128
- Starting kernel ...
- [ 0.000000] Linux version 4.14.89 (ador@ubuntu) (gcc version 7.3.0 (OpenWrt G CC 7.3.0 r7365-95daf4c441)) #0 Tue Dec 18 17:25:50 2018
- [ 0.000000] Board has DDR2
- [ 0.000000] Analog PMU set to hw control
- [ 0.000000] Digital PMU set to hw control
- [ 0.000000] SoC Type: MediaTek MT7620A ver:2 eco:6
- [ 0.000000] Linux version 4.14.89 (ador@ubuntu) (gcc version 7.3.0 (OpenWrt G CC 7.3.0 r7365-95daf4c441)) #0 Tue Dec 18 17:25:50 2018
- [ 0.000000] Board has DDR2
- [ 0.000000] Analog PMU set to hw control
- [ 0.000000] Digital PMU set to hw control
- [ 0.000000] SoC Type: MediaTek MT7620A ver:2 eco:6
- [ 0.000000] Linux version 4.14.89 (ador@ubuntu) (gcc version 7.3.0 (OpenWrt G CC 7.3.0 r7365-95daf4c441)) #0 Tue Dec 18 17:25:50 2018
- [ 0.000000] Board has DDR2
复制代码
和这个情况一样:https://www.right.com.cn/FORUM/thread-2239741-1-1.html
各位大佬还有什么办法救砖啊,TTL已经选择不了!
|
|