恩山无线论坛

 找回密码
 立即注册

QQ登录

只需一步,快速开始

搜索
查看: 2052|回复: 14

[k2t] K2T固件没刷breed直接升级到L大的OP,进退无路了

[复制链接]
发表于 2019-4-14 17:26 | 显示全部楼层 |阅读模式
本帖最后由 a7077447 于 2019-4-15 20:30 编辑

K2T固件没刷breed直接升级到L大的OP,进退无路了

在刷L大的OP时就感觉点快了


在这个OP里想刷breed,刷回官改都行不通了,UBOOT锁定了,,,,,,,不能升任何固件了



第一次用TTL大法,,,,TTL的权限真是高

TTL大法,进入OP,用TTL大法可以写入BREED或固件,,,

完美修复

1、正确连接TTL线,用PUTTY串口登陆COM4   115200等(自己的电脑硬件查看COM?),
2、在op中开启SSH,,用WinSCP或hfs等上传BREED或固件
3、在PUTTY中运行命令



我的恩山、我的无线 The best wifi forum is right here.
 楼主| 发表于 2019-4-14 17:30 | 显示全部楼层
以为A大的官改有breed了,,,,,,,没进BREED就在官改中直刷L大的OP。。。

这货还有救的方法吗

可以退回去官方固件,重新再来一次吗
我的恩山、我的无线 The best wifi forum is right here.
 楼主| 发表于 2019-4-14 17:33 | 显示全部楼层
本帖最后由 a7077447 于 2019-4-14 20:19 编辑

以前是K2T_V22.23.1.108.bin的

下载了个
K2T_V22.23.1.140

退不回去了



可能是拆机TTL或上编程器的








我的恩山、我的无线 The best wifi forum is right here.
 楼主| 发表于 2019-4-15 17:33 | 显示全部楼层
[    0.567602] console [ttyS0] enabled
[    0.567602] console [ttyS0] enabled
[    0.575161] bootconsole [early0] disabled
[    0.575161] bootconsole [early0] disabled
[    0.586475] m25p80 spi0.0: found gd25q128, expected m25p80
[    0.594227] m25p80 spi0.0: gd25q128 (16384 Kbytes)
[    0.599202] 5 cmdlinepart partitions found on MTD device spi0.0
[    0.605346] Creating 5 MTD partitions on "spi0.0":
[    0.610300] 0x000000000000-0x000000030000 : "u-boot"
[    0.616627] 0x000000030000-0x000000040000 : "config"
[    0.623093] 0x000000040000-0x000000090000 : "permanent"
[    0.629734] 0x000000090000-0x000000ff0000 : "firmware"
[    0.661703] 2 uimage-fw partitions found on MTD device firmware
[    0.667833] 0x000000090000-0x0000001e0000 : "kernel"
[    0.674072] 0x0000001e0000-0x000000ff0000 : "rootfs"
[    0.680475] mtd: device 5 (rootfs) set to be root filesystem
[    0.686408] 1 squashfs-split partitions found on MTD device rootfs
[    0.692806] 0x0000008b0000-0x000000ff0000 : "rootfs_data"
[    0.699686] 0x000000ff0000-0x000001000000 : "art"
[    0.706659] libphy: Fixed MDIO Bus: probed
[    0.722573] switch0: Atheros AR8337 rev. 2 switch registered on ag71xx-mdio.0

[    1.408713] libphy: ag71xx_mdio: probed
[    2.042832] ag71xx ag71xx.0: connected to PHY at ag71xx-mdio.0:00 [uid=004dd0
36, driver=Atheros AR8216/AR8236/AR8316]
[    2.054385] eth0: Atheros AG71xx at 0xb9000000, irq 4, mode:SGMII
[    2.062024] NET: Registered protocol family 10
[    2.069204] NET: Registered protocol family 17
[    2.073980] 8021q: 802.1Q VLAN Support v1.8
[    2.084250] VFS: Mounted root (squashfs filesystem) readonly on device 31:5.
[    2.093266] Freeing unused kernel memory: 312K
[    2.097856] This architecture does not have kernel memory protection.
[    2.571411] random: fast init done
[    2.778986] init: Console is alive
[    2.782744] init: - watchdog -
[    4.706041] kmodloader: loading kernel modules from /etc/modules-boot.d/*
[    4.824630] usbcore: registered new interface driver usbfs
[    4.830356] usbcore: registered new interface driver hub
[    4.835966] usbcore: registered new device driver usb
[    4.868579] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[    4.882784] SCSI subsystem initialized
[    4.891008] ehci-platform: EHCI generic platform driver
[    4.896533] ehci-platform ehci-platform.0: EHCI Host Controller
[    4.902689] ehci-platform ehci-platform.0: new USB bus registered, assigned b
us number 1
[    4.913132] ehci-platform ehci-platform.0: irq 48, io mem 0x1b000000
[    4.941416] ehci-platform ehci-platform.0: USB 2.0 started, EHCI 1.00
[    4.948782] hub 1-0:1.0: USB hub found
[    4.952988] hub 1-0:1.0: 1 port detected
[    4.957342] ehci-platform ehci-platform.1: EHCI Host Controller
[    4.963521] ehci-platform ehci-platform.1: new USB bus registered, assigned b
us number 2
[    4.973990] ehci-platform ehci-platform.1: irq 49, io mem 0x1b400000
[    5.001399] ehci-platform ehci-platform.1: USB 2.0 started, EHCI 1.00
[    5.008746] hub 2-0:1.0: USB hub found
[    5.012964] hub 2-0:1.0: 1 port detected
[    5.020864] usbcore: registered new interface driver usb-storage
[    5.027781] kmodloader: done loading kernel modules from /etc/modules-boot.d/
*
[    5.037600] init: - preinit -
[    5.908848] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
Press the [f] key and hit [enter] to enter failsafe mode
Press the [1], [2], [3] or [4] key and hit [enter] to [    6.046737] random: pro
cd: uninitialized urandom read (4 bytes read)
select the debug level
[    6.992790] eth0: link up (1000Mbps/Full duplex)
[    6.997683] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[    9.205965] mount_root: loading kmods from internal overlay
[    9.271089] kmodloader: loading kernel modules from //etc/modules-boot.d/*
[    9.279784] kmodloader: done loading kernel modules from //etc/modules-boot.d
/*
[    9.698102] jffs2: notice: (443) jffs2_build_xattr_subsystem: complete buildi
ng xattr subsystem, 0 of xdatum (0 unchecked, 0 orphan) and 0 of xref (0 dead, 0
orphan) found.
[    9.722048] block: attempting to load /tmp/jffs_cfg/upper/etc/config/fstab
[    9.742378] block: extroot: not configured
[    9.838308] jffs2: notice: (441) jffs2_build_xattr_subsystem: complete buildi
ng xattr subsystem, 0 of xdatum (0 unchecked, 0 orphan) and 0 of xref (0 dead, 0
orphan) found.
[    9.855491] mount_root: loading kmods from internal overlay
[    9.917470] kmodloader: loading kernel modules from /tmp/overlay/upper/etc/mo
dules-boot.d/*
[    9.929128] kmodloader: done loading kernel modules from /tmp/overlay/upper/e
tc/modules-boot.d/*
[   10.158931] block: attempting to load /tmp/jffs_cfg/upper/etc/config/fstab
[   10.172039] block: extroot: not configured
[   10.177105] mount_root: switching to jffs2 overlay
[   10.243704] urandom-seed: Seeding with /etc/urandom.seed
[   10.359952] eth0: link down
[   10.373514] procd: - early -
[   10.376574] procd: - watchdog -
[   11.013986] procd: - watchdog -
[   11.017454] procd: - ubus -
[   11.248540] random: ubusd: uninitialized urandom read (4 bytes read)
[   11.363793] random: ubusd: uninitialized urandom read (4 bytes read)
[   11.370764] random: ubusd: uninitialized urandom read (4 bytes read)
[   11.389711] procd: - init -
Please press Enter to activate this console.
[   12.085523] kmodloader: loading kernel modules from /etc/modules.d/*
[   12.194709] Initializing XFRM netlink socket
[   12.211556] NET: Registered protocol family 15
[   12.276776] gre: GRE over IPv4 demultiplexor driver
[   12.291210] ip_gre: GRE over IPv4 tunneling driver
[   12.329760] ip6_tables: (C) 2000-2006 Netfilter Core Team
[   12.362958] Netfilter messages via NETLINK v0.30.
[   12.375670] ip_set: protocol 6
[   12.484607] u32 classifier
[   12.487406]     input device check on
[   12.491185]     Actions configured
[   12.497490] Mirror/redirect action on
[   12.523765] nf_conntrack version 0.5.0 (1024 buckets, 4096 max)
[   12.558475] fuse init (API version 7.26)
[   12.572296] Loading modules backported from Linux version wt-2017-11-01-0-gfe
248fc2c180
[   12.580564] Backport generated by backports.git v4.14-rc2-1-31-g86cf0e5d
[   12.624224] ip_tables: (C) 2000-2006 Netfilter Core Team
[   12.791114] ctnetlink v0.93: registering with nfnetlink.
[   13.017575] usbcore: registered new interface driver ums-alauda
[   13.028687] usbcore: registered new interface driver ums-cypress
[   13.048987] usbcore: registered new interface driver ums-datafab
[   13.074914] usbcore: registered new interface driver ums-freecom
[   13.083709] usbcore: registered new interface driver ums-isd200
[   13.103895] usbcore: registered new interface driver ums-jumpshot
[   13.130588] usbcore: registered new interface driver ums-karma
[   13.144137] usbcore: registered new interface driver ums-sddr09
[   13.155431] usbcore: registered new interface driver ums-sddr55
[   13.173351] usbcore: registered new interface driver ums-usbat
[   13.199884] usbcore: registered new interface driver usblp
[   13.286866] xt_time: kernel timezone is -0000
[   13.352555] fast-classifier: starting up
[   13.356757] fast-classifier: registered
[   13.491200] PPP generic driver version 2.4.2
[   13.498337] PPP MPPE Compression module registered
[   13.511582] NET: Registered protocol family 24
[   13.582103] PCI: Enabling device 0000:00:00.0 (0000 -> 0002)
[   13.588270] ath10k_pci 0000:00:00.0: pci irq legacy oper_irq_mode 1 irq_mode
0 reset_mode 0
[   13.824404] ath10k_pci 0000:00:00.0: Direct firmware load for ath10k/QCA9888/
hw2.0/firmware-6.bin failed with error -2
[   13.835496] ath10k_pci 0000:00:00.0: Falling back to user helper
[   15.024061] firmware ath10k!QCA9888!hw2.0!firmware-6.bin: firmware_loading_st
ore: map pages failed
[   15.619475] ath10k_pci 0000:00:00.0: qca9888 hw2.0 target 0x01000000 chip_id
0x00000000 sub 0000:0000
[   15.629052] ath10k_pci 0000:00:00.0: kconfig debug 0 debugfs 1 tracing 0 dfs
1 testmode 1
[   15.649568] ath10k_pci 0000:00:00.0: firmware ver 10.4-3.5.3-00053 api 5 feat
ures no-p2p,mfp,peer-flow-ctrl,allows-mesh-bcast,no-ps crc32 a9603656
[   15.966119] ath10k_pci 0000:00:00.0: failed to fetch board data for bus=pci,b
mi-chip-id=0,bmi-board-id=20 from ath10k/QCA9888/hw2.0/board-2.bin
[   15.982114] ath10k_pci 0000:00:00.0: board_file api 1 bmi_id 0:20 crc32 d903d
a92
[   18.142015] ath10k_pci 0000:00:00.0: htt-ver 2.2 wmi-op 6 htt-op 4 cal pre-ca
l-file max-sta 512 raw 0 hwcrypto 1
[   18.436394] ieee80211 phy1: Atheros AR9561 Rev:0 mem=0xb8100000, irq=47
[   18.460897] kmodloader: done loading kernel modules from /etc/modules.d/*
[   19.712850] urandom_read: 5 callbacks suppressed
[   19.712857] random: jshn: uninitialized urandom read (4 bytes read)
[   25.301649] jffs2: notice: (1320) jffs2_build_xattr_subsystem: complete build
ing xattr subsystem, 0 of xdatum (0 unchecked, 0 orphan) and 0 of xref (0 dead,
0 orphan) found.
[   26.605302] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[   26.625607] br-lan: port 1(eth0.1) entered blocking state
[   26.631192] br-lan: port 1(eth0.1) entered disabled state
[   26.637133] device eth0.1 entered promiscuous mode
[   26.642134] device eth0 entered promiscuous mode
[   26.675642] IPv6: ADDRCONF(NETDEV_UP): br-lan: link is not ready
[   26.675642] IPv6: ADDRCONF(NETDEV_UP): br-lan: link is not ready
[   27.633024] eth0: link up (1000Mbps/Full duplex)
[   27.637909] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[   27.783538] br-lan: port 1(eth0.1) entered blocking state
[   27.789123] br-lan: port 1(eth0.1) entered forwarding state
[   27.795058] IPv6: ADDRCONF(NETDEV_CHANGE): eth0.2: link becomes ready
[   27.946232] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready
[   35.188063] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
[   35.211651] IPv6: ADDRCONF(NETDEV_UP): wlan1: link is not ready
[   35.249507] br-lan: port 2(wlan0) entered blocking state
[   35.255050] br-lan: port 2(wlan0) entered disabled state
[   35.260856] device wlan0 entered promiscuous mode
[   35.284270] br-lan: port 3(wlan1) entered blocking state
[   35.289769] br-lan: port 3(wlan1) entered disabled state
[   35.295630] device wlan1 entered promiscuous mode
[   35.300559] br-lan: port 3(wlan1) entered blocking state
[   35.306088] br-lan: port 3(wlan1) entered forwarding state
[   36.271514] br-lan: port 3(wlan1) entered disabled state
[   37.032130] IPv6: ADDRCONF(NETDEV_CHANGE): wlan1: link becomes ready
[   37.038826] br-lan: port 3(wlan1) entered blocking state
[   37.044369] br-lan: port 3(wlan1) entered forwarding state
[   37.421614] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
[   37.428333] br-lan: port 2(wlan0) entered blocking state
[   37.433871] br-lan: port 2(wlan0) entered forwarding state
我的恩山、我的无线 The best wifi forum is right here.
 楼主| 发表于 2019-4-15 17:43 | 显示全部楼层
本帖最后由 a7077447 于 2019-4-15 18:08 编辑

死不死的....砖了还有教程

官方UBOOT+OPENWRT

i这种BREED....如何刷

如何中止TTL
上电源的同时按下计算的CTRL+C按键,不要放开,这样就能中止AP的启动

我的恩山、我的无线 The best wifi forum is right here.
 楼主| 发表于 2019-4-15 19:27 | 显示全部楼层
系统       
主机名NATCAP
主机型号Phicomm K2T A1/A2/A3 board
固件版本                         NATCAP 3.0.0_build201805260551 Beetle r7091+1-6c5235ff30 /                        LuCI Master (git-18.147.50759-d8a67bf)               
内核版本4.9.102
本地时间Mon Apr 15 19:27:27 2019
运行时间0h 4m 24s

我的恩山、我的无线 The best wifi forum is right here.
发表于 2019-4-15 20:04 | 显示全部楼层
等待大神回复

点评

自己搞定了..TTL大法  详情 回复 发表于 2019-4-15 20:08
我的恩山、我的无线 The best wifi forum is right here.
 楼主| 发表于 2019-4-15 20:08 | 显示全部楼层

自己搞定了..TTL大法
我的恩山、我的无线 The best wifi forum is right here.
发表于 2019-4-15 20:32 | 显示全部楼层
mleaf大神的OP不好吗?我觉得挺好的呀

点评

只是要把官方的UBOOT换成BREED 有BREED才有折腾的乐趣  详情 回复 发表于 2019-4-16 10:33
我的恩山、我的无线 The best wifi forum is right here.
 楼主| 发表于 2019-4-16 10:33 | 显示全部楼层
懒懒猪 发表于 2019-4-15 20:32
mleaf大神的OP不好吗?我觉得挺好的呀

只是要把官方的UBOOT换成BREED

有BREED才有折腾的乐趣
我的恩山、我的无线 The best wifi forum is right here.
发表于 2019-5-29 00:02 | 显示全部楼层
手上有一只别人的K2T,是一个官改,不知是否刷入Breed,但尝试很多次无法进入,应该是没有刷入吧。电脑没有网线接口,懒得买转接,请问有办法重新刷入Breed吗?

点评

求详细指导  详情 回复 发表于 2019-5-29 09:27
官改没有breed,,,要刷解UBOOT的固件,,,再刷breed  发表于 2019-5-29 08:58
我的恩山、我的无线 The best wifi forum is right here.
发表于 2019-5-29 09:27 | 显示全部楼层
N4030 发表于 2019-5-29 00:02
手上有一只别人的K2T,是一个官改,不知是否刷入Breed,但尝试很多次无法进入,应该是没有刷入吧。电脑没有 ...

求详细指导
我的恩山、我的无线 The best wifi forum is right here.
您需要登录后才可以回帖 登录 | 立即注册

本版积分规则

QQ|手机版|小黑屋|Archiver|恩山无线论坛(常州市恩山计算机开发有限公司版权所有) ( 苏ICP备05084872号 )|网站地图

GMT+8, 2020-2-22 01:56

Powered by Discuz! X3.4

Copyright © 2001-2020, Tencent Cloud.

快速回复 返回顶部 返回列表