高手们进，看看是什么东西

li98*** · 发表于 2019-4-24 10:49

这个东西，有一个网口，一个电源口，一个usb2.0 一个usb3.0 一个mini sd卡插槽，内部有一个硬盘接口，现在是插上东西都认，就是不知道怎么用，我感觉是一个网络存储，但是网上邻居也找不到，网页也打不开。完全一个黑盒。幸好串口信息可以看到。

一个黑色的盒子，上面就这几个字母。什么都没有。
下面是串口信息：
XCode SoC booting ===>>>OK!

U-Boot 2013.01-rc2 (Sep 16 2014 - 16:13:18)

CPU  : XCode 6 Rev 1
Board: XCode6 SDK
Baord: Memory Channel 0 presents.
Memory Init Board: 0x1601
Memory Init Ver: 10.63-0
Memory Init Speed: 1600MHz
Top of RAM usable for U-Boot at: 3fff0000
Reserving 827k for U-Boot at: 3ff21000
DRAM:  1 GiB
SF: Detected N25Q64 with page size 256 Bytes, erase size 4 KiB, sector size 64 KiB, total 8 MiB
MMC: XCode SD/MMC: 0
In: serial
Out: serial
Err: serial
Net: 100M/10M Ethernet is used.
RGMII PHY is used.
eth0

SW button is pressed, enter WNC tiny linux ...

SF: Detected N25Q64 with page size 256 Bytes, erase size 4 KiB, sector size 64 KiB, total 8 MiB
## Booting kernel from Legacy Image at 10000000 ...
Image Name: ARM Linux Kernel
Image Type: ARM Linux Kernel Image (gzip compressed)
Data Size: 6104308 Bytes = 5.8 MiB
Load Address: 60000000
Entry Point:  60000000
Verifying Checksum ... OK
## Adjust Kernel size, FB size 0x40000000 size 256MB kernel entry 0x30000000,
Uncompressing Kernel Image ... OK
<NULL> is not valid, use sdk default root

Starting kernel ...

Mach ID = 3506 ATAG 14800000 Kernel Entry 30000000[ 0.000000] Booting Linux on physical CPU 0xa00
[ 0.000000] Linux version 3.10.12 (root@localhost.localdomain) (gcc version 4.7.3 20121106 (prerelease) (crosstool-NG linaro-1.13.1-4.7-2012.11-20121123 - Linaro GCC 2012.11) ) #68 SMP Tue Sep 16 00:32:59 EDT 2014
[ 0.000000] CPU: ARMv7 Processor [414fc091] revision 1 (ARMv7), cr=50c5387d
[ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
[ 0.000000] >>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>ATAG at 14800000
[ 0.000000] Machine: Xcode6
[ 0.000000] Parse tag 54410001
[ 0.000000] Parse tag 54410009
[ 0.000000] Parse tag 54410007
[ 0.000000] Memory policy: ECC disabled, Data cache writealloc
[ 0.000000] On node 0 totalpages: 65280
[ 0.000000] free_area_init_node: node 0, pgdat 80abfbc0, node_mem_map 81004000
[ 0.000000] Normal zone: 510 pages used for memmap
[ 0.000000] Normal zone: 0 pages reserved
[ 0.000000] Normal zone: 65280 pages, LIFO batch:15
[ 0.000000] PERCPU: Embedded 7 pages/cpu @81209000 s8128 r8192 d12352 u32768
[ 0.000000] pcpu-alloc: s8128 r8192 d12352 u32768 alloc=8*4096
[ 0.000000] pcpu-alloc: [0] 0 [0] 1
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 64770
[ 0.000000] Kernel command line: earlyprintk loglevel=8 console=ttyS0,115200 initcall_debug=0 ethaddr=E8:FC:AF:BB:2C:AC root=/dev/sda2 mem=255M bootver=15000003:e4ebe98d
[ 0.000000] Set eth0 MAC address to E8:FC:AF:BB:2C:AC
[ 0.000000] PID hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.000000] Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
[ 0.000000] Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
[ 0.000000] Memory: 255MB = 255MB total
[ 0.000000] Memory: 242384k/242384k available, 18736k reserved, 0K highmem
[ 0.000000] Virtual kernel memory layout:
[ 0.000000]    vector  : 0xffff0000 - 0xffff1000 ( 4 kB)
[ 0.000000]    fixmap  : 0xfff00000 - 0xfffe0000 ( 896 kB)
[ 0.000000]    vmalloc : 0x90000000 - 0xffff0000 (1791 MB)
[ 0.000000]    lowmem  : 0x80000000 - 0x8ff00000 ( 255 MB)
[ 0.000000]    pkmap : 0x7fe00000 - 0x80000000 ( 2 MB)
[ 0.000000]    modules : 0x7f800000 - 0x7fe00000 ( 6 MB)
[ 0.000000]    .text : 0x80008000 - 0x80567ec4 (5504 kB)
[ 0.000000]    .init : 0x80568000 - 0x80a69fc0 (5128 kB)
[ 0.000000]    .data : 0x80a6a000 - 0x80ac0920 ( 347 kB)
[ 0.000000]       .bss : 0x80ac0920 - 0x810036e0 (5388 kB)
[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=2, Nodes=1
[ 0.000000] Hierarchical RCU implementation.
[ 0.000000]  RCU debugfs-based tracing is enabled.
[ 0.000000]  Additional per-CPU info printed with stalls.
[ 0.000000] NR_IRQS:376
[ 0.000000] sched_clock: 32 bits at 100 Hz, resolution 10000000ns, wraps every 4294967286ms
[ 0.000000] Console: colour dummy device 80x30
[ 0.000000] UART0: Buffer RX 8f806000 TX 8f803000
[ 0.000000] UART1: Buffer RX 8f80c000 TX 8f807000
[ 0.000000] console [ttyS0] enabled
[ 0.000000] Lock dependency validator: Copyright (c) 2006 Red Hat, Inc., Ingo Molnar
[ 0.000000] ... MAX_LOCKDEP_SUBCLASSES:  8
[ 0.000000] ... MAX_LOCK_DEPTH:       48
[ 0.000000] ... MAX_LOCKDEP_KEYS:       8191
[ 0.000000] ... CLASSHASH_SIZE:       4096
[ 0.000000] ... MAX_LOCKDEP_ENTRIES:    16384
[ 0.000000] ... MAX_LOCKDEP_CHAINS:    32768
[ 0.000000] ... CHAINHASH_SIZE:       16384
[ 0.000000]  memory used by lock dependency info: 3695 kB
[ 0.000000]  per task-struct memory footprint: 1152 bytes
[ 0.230000] Calibrating delay loop... 1889.07 BogoMIPS (lpj=9445376)
[ 0.300000] pid_max: default: 32768 minimum: 301
[ 0.300000] Mount-cache hash table entries: 512
[ 0.310000] CPU: Testing write buffer coherency: ok
[ 0.310000] Kernel_init started
[ 0.310000] CPU0: thread -1, cpu 0, socket 10, mpidr 80000a00
[ 0.320000] Wake secondary....do nothing now!
[ 0.320000] Setting up static identity map for 0x80365b88 - 0x80365bd4
[ 0.330000] l2x0: Turn on L2 cache
[ 0.330000] L310 cache controller enabled
[ 0.340000] l2x0: 16 ways, CACHE_ID 0x410000c8, AUX_CTRL 0x7e470000, Cache size: 1048576 B
[ 0.350000] CPU1: Booted secondary processor
[ 0.410000] CPU1: thread -1, cpu 1, socket 10, mpidr 80000a01
[ 0.410000] Brought up 2 CPUs
[ 0.420000] SMP: Total of 2 processors activated (3784.70 BogoMIPS).
[ 0.420000] CPU: All CPU(s) started in SVC mode.
[ 0.430000] devtmpfs: initialized
[ 0.440000] NET: Registered protocol family 16
[ 0.440000] DMA: preallocated 256 KiB pool for atomic coherent allocations
[ 0.450000] [InitPCIeHostBridge:206] pcie :0 as host PCIE_HOST_FB_MASK:1
[ 1.860000] [InitPCIeHostBridge:261]PCIEH:0: link is not up !
[ 1.860000] [InitPCIeHostBridge:206] pcie :1 as host PCIE_HOST_FB_MASK:fff00001
[ 2.980000] [InitPCIeHostBridge:261]PCIEH:1: link is not up !
[ 2.990000] bio: create slab <bio-0> at 0
[ 2.990000] SCSI subsystem initialized
[ 3.000000] libata version 3.00 loaded.
[ 3.000000] usbcore: registered new interface driver usbfs
[ 3.010000] usbcore: registered new interface driver hub
[ 3.010000] usbcore: registered new device driver usb
[ 3.020000] Switching to clocksource ARM Core Global Timer
[ 3.020000] FS-Cache: Loaded
[ 3.040000] NET: Registered protocol family 2
[ 3.040000] TCP established hash table entries: 2048 (order: 2, 16384 bytes)
[ 3.050000] TCP bind hash table entries: 2048 (order: 4, 73728 bytes)
[ 3.050000] TCP: Hash tables configured (established 2048 bind 2048)
[ 3.060000] TCP: reno registered
[ 3.060000] UDP hash table entries: 256 (order: 2, 20480 bytes)
[ 3.070000] UDP-Lite hash table entries: 256 (order: 2, 20480 bytes)
[ 3.080000] NET: Registered protocol family 1
[ 3.080000] RPC: Registered named UNIX socket transport module.
[ 3.090000] RPC: Registered udp transport module.
[ 3.090000] RPC: Registered tcp transport module.
[ 3.100000] RPC: Registered tcp NFSv4.1 backchannel transport module.
[ 3.170000] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 3.180000] FS-Cache: Netfs 'nfs' registered for caching
[ 3.180000] NFS: Registering the id_resolver key type
[ 3.190000] Key type id_resolver registered
[ 3.190000] Key type id_legacy registered
[ 3.190000] Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
[ 3.200000] FS-Cache: Netfs 'cifs' registered for caching
[ 3.210000] NTFS driver 2.1.30 [Flags: R/O].
[ 3.210000] ROMFS MTD (C) 2007 Red Hat, Inc.
[ 3.220000] fuse init (API version 7.22)
[ 3.220000] SGI XFS with security attributes, large block/inode numbers, no debug enabled
[ 3.230000] yaffs: yaffs built Sep 16 2014 00:31:28 Installing.
[ 3.230000] msgmni has been set to 473
[ 3.240000] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 253)
[ 3.240000] io scheduler noop registered
[ 3.250000] io scheduler deadline registered
[ 3.250000] io scheduler cfq registered (default)
[ 3.260000] PROBE UART
[ 3.260000] XCODE_SERIAL_INIT
[ 3.260000] Xcode serial driver version 1.00
[ 3.270000] ttyS0 (irq = 85, address = 0xffeef400) is a builtin UART
[ 3.270000] ttyS1 (irq = 86, address = 0xffeef450) is a builtin UART
[ 3.290000] brd: module loaded
[ 3.300000] loop: module loaded
[ 3.300000] nbd: registered device at major 43
[ 3.310000] xcode-ahci-host0 xcode-ahci-host0: version 3.0
[ 3.310000] Init host controller
[ 3.320000] xcode-ahci-host0 xcode-ahci-host0: forcing PORTS_IMPL to 0x1
[ 4.340000] xcode-ahci-host0 xcode-ahci-host0: AHCI 0001.0300 32 slots 1 ports 3 Gbps 0x1 impl SATA mode
[ 4.340000] xcode-ahci-host0 xcode-ahci-host0: flags: ncq sntf pm led clo only pmp pio slum part
[ 4.350000] Activate ahci host
[ 4.360000] Request irq 58 80
[ 4.360000] scsi0 : xcode-ahci
[ 4.360000] ata1: SATA max UDMA/133 irq_stat 0x00400040, connection status changed irq 58
[ 4.370000] xcode-ahci-host1 xcode-ahci-host1: forcing PORTS_IMPL to 0x1
[ 5.300000] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
[ 5.300000] ata1.00: ATA-8: HGST HTS541010A9E680, JA0OA560, max UDMA/133
[ 5.310000] ata1.00: 1953525168 sectors, multi 16: LBA48 NCQ (depth 31/32)
[ 5.310000] ata1.00: configured for UDMA/133
[ 5.320000] scsi 0:0:0:0: Direct-Access    ATA    HGST HTS541010A9 JA0O PQ: 0 ANSI: 5
[ 5.330000] sd 0:0:0:0: [sda] 1953525168 512-byte logical blocks: (1.00 TB/931 GiB)
[ 5.330000] sd 0:0:0:0: [sda] 4096-byte physical blocks
[ 5.340000] sd 0:0:0:0: [sda] Write Protect is off
[ 5.340000] sd 0:0:0:0: Attached scsi generic sg0 type 0
[ 5.350000] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 5.350000] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 5.380000] xcode-ahci-host1 xcode-ahci-host1: AHCI 0001.0300 32 slots 1 ports 3 Gbps 0x1 impl SATA mode
[ 5.380000] xcode-ahci-host1 xcode-ahci-host1: flags: ncq sntf pm led clo only pmp pio slum part
[ 5.390000] Activate ahci host
[ 5.400000] scsi1 : xcode-ahci
[ 5.400000] ata2: SATA max UDMA/133 irq 58
[ 5.400000] Start NAND device initializing
[ 5.400000] xcode_nand board id 0x1600 io_buffer virt=0x8ed18000, phys=0x3ed18000
[ 5.630000] 18 18 18 18 18 ff ff ff
[ 5.630000] No NAND device found
[ 5.630000] Xcode NAND flash driver initialization failed!
[ 5.640000] No NAND device detected
[ 5.640000] tun: Universal TUN/TAP device driver, 1.6
[ 5.640000] tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
[ 5.650000] SynopGMAC: **********************************************************
[ 5.660000] SynopGMAC: * Driver :This is Synopsys GMAC-UNIV PCI-Network Driver
[ 5.670000] SynopGMAC: * Version :1.0
[ 5.670000]  sda: sda1 < sda5 >
[ 5.670000] sd 0:0:0:0: [sda] Attached SCSI disk
[ 5.680000] SynopGMAC: * Copyright :Copyright (c) 2007-2007 Synopsys, Inc
[ 5.680000] SynopGMAC: **********************************************************
[ 5.690000] SynopGMAC: Initializing synopsys GMAC interfaces ..
[ 5.700000] Turn on GTX clock
[ 5.700000] SynopGMAC: select RGMII interface for eth 1
[ 5.750000] ata2: SATA link down (SStatus 0 SControl 300)
[ 5.760000] SynopGMAC: Find ethernet phy device:0x01410e20.Phy index:19
[ 5.770000] Ethernet PHY, get address 22, 4a44
[ 5.770000] Ethernet PHY, get address 22 second time, 4e85
[ 5.780000] SynopGMAC: tso buf at 900a3000, phy at 3e800000 size=0x2f5000
[ 5.800000] SynopGMAC: Find ethernet phy device:0x00000000.Phy index:0
[ 5.810000] SynopGMAC: tso buf at 903af000, phy at 3e400000 size=0x2f5000
[ 5.810000] synopsis_init
[ 5.820000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 5.820000] Start: SDUH EHCI device registed to platform bus
[ 5.830000] END: SDUH EHCI device registed to platform bus
[ 5.830000] sduh-ehci sduh-ehci: initializing XCode-SOC USB Controller
[ 5.840000] SDUH_HCD_REG_BASE is  ffee2000
[ 5.840000] sduh-ehci sduh-ehci: Vixs On-Chip EHCI Host Controller
[ 5.850000] sduh-ehci sduh-ehci: new USB bus registered, assigned bus number 1
[ 5.860000] try reset SDUH controller
[ 5.870000] reset SDUH controller end
[ 5.870000] phy register setting end
[ 5.870000] enable interrupt mask end
[ 5.880000] try to read ehci cap register
[ 5.880000] try to read ehci params register
[ 5.890000] try to call ehci_halt
[ 5.890000] try to call ehci_init
[ 5.890000] sduh-ehci sduh-ehci: irq 64, io base 0xffee2000
[ 5.920000] sduh-ehci sduh-ehci: USB 2.0 started, EHCI 1.00
[ 5.920000] hub 1-0:1.0: USB hub found
[ 5.920000] hub 1-0:1.0: 2 ports detected
[ 5.930000] usb_hcd_sduh_probe: SDUH add success
[ 5.930000] ehci-pci: EHCI PCI platform driver
[ 5.940000] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[ 5.940000] Start: SDUH OHCI device registed to platform bus
[ 5.950000] END: SDUH OHCI device registed to platform bus
[ 5.950000] sduh-ohci sduh-ohci: initializing Xcode-SOC USB OHCI Controller
[ 5.960000] sduh-ohci sduh-ohci: Vixs On-Chip OHCI Host Controller
[ 5.970000] sduh-ohci sduh-ohci: new USB bus registered, assigned bus number 2
[ 5.970000] sduh-ohci sduh-ohci: irq 64, io mem 0xffee2000
[ 5.980000] enable interrupt mask endOHCI SDUH setup finished
[ 6.040000] hub 2-0:1.0: USB hub found
[ 6.040000] hub 2-0:1.0: 2 ports detected
[ 6.050000] uhci_hcd: USB Universal Host Controller Interface driver
[ 6.050000] xhci_register_plat 214
[ 6.060000] Start: SDUH XHCI device registed to platform bus
[ 6.170000] (__le32 *)0xc200=0xc0002540
[ 6.170000] GUSB3PIPECTL=0x010e0002
[ 6.180000] GCTL=0x30c01004
[ 6.190000] GUSB3PIPECTL (2) = 0x810e0002
[ 6.200000] END: SDUH XHCI device registed to platform bus
[ 6.210000] xhci-hcd xhci-hcd: xHCI Host Controller
[ 6.210000] xhci-hcd xhci-hcd: new USB bus registered, assigned bus number 3
[ 6.220000] xhci-hcd xhci-hcd: irq 63, io mem 0xffef2000
[ 6.220000] xHCI xhci_add_endpoint called for root hub
[ 6.230000] xHCI xhci_check_bandwidth called for root hub
[ 6.230000] hub 3-0:1.0: USB hub found
[ 6.240000] hub 3-0:1.0: 1 port detected
[ 6.240000] xhci-hcd xhci-hcd: xHCI Host Controller
[ 6.250000] xhci-hcd xhci-hcd: new USB bus registered, assigned bus number 4
[ 6.260000] xHCI xhci_add_endpoint called for root hub
[ 6.260000] xHCI xhci_check_bandwidth called for root hub
[ 6.260000] hub 4-0:1.0: USB hub found
[ 6.270000] hub 4-0:1.0: 1 port detected
[ 6.270000] usbcore: registered new interface driver usb-storage
[ 6.280000] mousedev: PS/2 mouse device common for all mice
[ 6.280000] xcode_wdt_init: Initializing XCode Watchdog
[ 6.290000] xcode_wdt: XCODE Watchdog Timer: initial timeout 10 sec
[ 6.300000] xcsdh_init: Initializing XCode SD controller
[ 6.320000] usb 1-1: new high-speed USB device number 2 using sduh-ehci
[ 6.340000] usbcore: registered new interface driver usbhid
[ 6.340000] usbhid: USB HID core driver
[ 6.340000] oprofile: hardware counters not available
[ 6.350000] oprofile: using timer interrupt.
[ 6.350000] TCP: cubic registered
[ 6.360000] NET: Registered protocol family 10
[ 6.360000] sit: IPv6 over IPv4 tunneling driver
[ 6.370000] NET: Registered protocol family 17
[ 6.370000] 8021q: 802.1Q VLAN Support v1.8
[ 6.370000] Key type dns_resolver registered
[ 6.380000] VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 4
[ 6.390000] ThumbEE CPU extension supported.
[ 6.390000] Registering SWP/SWPB emulation handler
[ 6.400000] All initcall [ 6.400000] Freeing unused kernel memory: 5124K (80568000 - 80a69000)
S01: system init enter..................................................
proc on /proc type proc (rw,relatime)
[ 6.470000] usb-storage 1-1:1.0: USB Mass Storage device detected
[ 6.470000] scsi2 : usb-storage 1-1:1.0
Initializing random number generator... done.
Starting network...
[ 7.490000] scsi 2:0:0:0: Direct-Access    Kingston DataTraveler 2.0 1.00 PQ: 0 ANSI: 4
[ 7.490000] sd 2:0:0:0: Attached scsi generic sg1 type 0
[ 7.490000] sd 2:0:0:0: [sdb] 15131636 512-byte logical blocks: (7.74 GB/7.21 GiB)
[ 7.490000] sd 2:0:0:0: [sdb] Write Protect is off
[ 7.490000] sd 2:0:0:0: [sdb] Mode Sense: 45 00 00 00
[ 7.500000] sd 2:0:0:0: [sdb] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
[ 7.530000]  sdb: sdb1
[ 7.530000] sd 2:0:0:0: [sdb] Attached SCSI removable disk
[ 8.270000] SynopGMAC: Autonegotiation Complete, PHY_STATUS_REG=0x000078e9
[ 8.270000] SynopGMAC: Autonegotiation Complete, PHY_SPECIFIC_STATUS_REG=0x00007c00
[ 8.270000] SynopGMAC: take 1600 ms to auto-negotiation
[ 8.280000] SynopGMAC: Link up
[ 8.290000] SynopGMAC: Speed is 100 1
[ 8.290000] request irq 83
[ 8.290000] SynopGMAC: transmit desc at 0x9008d000 0x3ed40000
[ 8.290000] SynopGMAC: recv desc at 0x9009e000 0x3ed14000
[ 8.300000] SynopGMAC: enable HW checksum
[ 8.300000] SynopGMAC: enable TCP segmentation offload
PING 192.168.0.1 (192.168.0.1): 56 data bytes
64 bytes from 192.168.0.1: seq=0 ttl=64 time=1029.657 ms

--- 192.168.0.1 ping statistics ---
1 packets transmitted, 1 packets received, 0% packet loss
round-trip min/avg/max = 1029.657/1029.657/1029.657 ms
telnetd: starting
  port: 23; interface: any; login program: /bin/sh

Kernel IP routing table
Destination    Gateway       Genmask       Flags Metric Ref Use Iface
192.168.0.0    0.0.0.0       255.255.255.0 U    0    0       0 eth0

eth0    Link encap:Ethernet  HWaddr E8:FC:AF:BB:2C:AC
      inet addr:192.168.0.100  Bcast:192.168.0.255  Mask:255.255.255.0
      UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1
      RX packets:2 errors:0 dropped:0 overruns:0 frame:0
      TX packets:4 errors:0 dropped:0 overruns:0 carrier:0
      collisions:0 txqueuelen:1000
      RX bytes:158 (158.0 B)  TX bytes:252 (252.0 B)
      Interrupt:83

There is no MicroSD card.
HDD exists ...

[ 9.580000] NTFS volume version 3.1.
      Mount USB disk /dev/sdb1 to /mnt/usb1 successfully

各们高手们看看，见多识广，看看是个什么东西，怎么用，能不能刷机，刷成网络存储。

li98*** · 发表于 2019-4-24 10:58

用串口控制，ping 电脑ip可以ping通，电脑ping 192.168.0.100 也能拼通。如何进这个东西的界面。

xpa*** · 发表于 2019-4-24 12:21

Go Pro ？！？

li98*** · 发表于 2019-4-24 13:07

xpader 发表于 2019-4-24 12:21
Go Pro ？！？

到官网查了，是相机和配件，但是没有这款东西。

zren*** · 发表于 2019-4-24 13:48

用端口扫描看开了哪些，，，

li98*** · 发表于 2019-4-25 08:39

本帖最后由 li9823105 于 2019-4-25 08:59 编辑

zrenyi123 发表于 2019-4-24 13:48
用端口扫描看开了哪些，，，

看了看，23口开的。其它没有开。但是输入端口号还是进不去。

li98*** · 发表于 2019-4-25 09:12

再加三张外壳的照片。
电路板上有一个芯片，QCA6234XU-AM2D,网上查一下。不太清楚是蓝牙还是无线模块。有谁知道。

看这个天线不像是无线的，蓝牙也搜不到。谁解释下。

zren*** · 发表于 2019-4-26 00:13

gopro硬盘盒
https://www.right.com.cn/forum/thread-211823-1-1.html

li98*** · 发表于 2019-4-26 16:43

zrenyi123 发表于 2019-4-26 00:13
gopro硬盘盒
https://www.right.com.cn/forum/thread-211823-1-1.html

谢了，刚看了，果然是没有发布出来的产品，找都找不到。看看能有人给我一人固件吗。

lhn*** · 发表于 2019-5-9 06:26

楼主我还屯着两个在手上，一个已经能正常使用，一个在折腾改千兆。

lhn*** · 发表于 2019-5-9 06:30

li9823105 发表于 2019-4-25 09:12
再加三张外壳的照片。
电路板上有一个芯片，QCA6234XU-AM2D,网上查一下。不太清楚是蓝牙还是无线模 ...

是无线加蓝牙模块，无线可以当AP使用，但因为这个系统内没有桥接软件，只能配合上层路由的路由表才能正常上网。

li98*** · 发表于 2019-5-10 16:56

lhn1324 发表于 2019-5-9 06:26
楼主我还屯着两个在手上，一个已经能正常使用，一个在折腾改千兆。

太利害了，我这个折腾废了，刷了几次没成，后来刷了不启动了，想把闪存焊下来写，结果焊下来一看，弄不了，贴片的，又焊上去了，也没焊好，通电没反应，这个算是折腾废了！！！想想这东西，还不如我把k2p路由加3.0口来的快，还省事。比这个还好用。

lhn*** · 发表于 2019-5-10 17:28

要能用确实不容易，不像路由刷个不死，然后随意上传固件就可以。这个要先刷Uboot，然后写入uImage，修改env，然后硬盘还要在Linux下分区并解包系统到硬盘分区。

li98*** · 发表于 2019-6-20 15:39

这几天实在没事，再找出来，折腾，贴片的不好搞，还搞断一个脚，找了一个16M的，16个脚的，对照定义，试了几次，竟然可以用。刚好这个闪存方便写，还有座。
试了好几个固件，有的不启，有的一直重启，这个一个这样，给看看
XCode SoC booting ===>>>OK!
Parameters from bootfw: 00000000 (Invalid)

U-Boot 2013.01-rc2-svn105296 (Jan 13 2015 - 09:27:05)

CPU  : XCode 6 Rev 1
Board: XCode6 SDK
Baord: Memory Channel 0 presents.
Memory Init Board: 0x1601
Memory Init Ver: 10.63-0
Memory Init Speed: 1600MHz
Top of RAM usable for U-Boot at: 3fff0000
Reserving 905k for U-Boot at: 3ff0d000
DRAM:  1 GiB
NAND:  No NAND device found!!!
XC NAND init failed
Total size: 0 MiB
MMC: XCODE MMC: Init SD core 1
XCode SD/MMC: 0, XCode SD/MMC: 1
SF: Detected S25FL128P_64K with page size 256 Bytes, erase size 64 KiB, sector size 64 KiB,

total 16 MiB
Using default environment

In: serial
Out: serial
Err: serial
Net: 1000M/100M/10M Ethernet is used.
RGMII PHY is used.
eth0
Hit any key to stop autoboot:  0
SF: Detected S25FL128P_64K with page size 256 Bytes, erase size 64 KiB, sector size 64 KiB,

total 16 MiB
Clock Freq is 100MHZ
Not supported SATA clock, set to default 125MHZ
Enable SATA SS mode
Target spinup took 11 ms.
AHCI 0001.0300 32 slots 1 ports 3 Gbps 0x1 impl SATA mode
flags: ncq stag pm led clo only pmp pio slum part ccc apst
scanning bus for devices...
ERROR: v7_dcache_inval_range - start address is not aligned - 0x3fe0b450 - 0x3fe0b650 cache

line 32
ERROR: v7_dcache_inval_range - stop address is not aligned - 0x3fe0b460 - 0x3fe0b650 cache

line 32
  Device 0: (0:0) Vendor: ATA Prod.: ST3320620SV Rev: 3.AC
         Type: Hard Disk
         Capacity: 305245.3 MB = 298.0 GB (625142448 x 512)
Found 1 device(s).

Reset SCSI
scanning bus for devices...
ERROR: v7_dcache_inval_range - start address is not aligned - 0x3fe0fa90 - 0x3fe0fc90 cache

line 32
ERROR: v7_dcache_inval_range - stop address is not aligned - 0x3fe0faa0 - 0x3fe0fc90 cache

line 32
  Device 0: (0:0) Vendor: ATA Prod.: ST3320620SV Rev: 3.AC
         Type: Hard Disk
         Capacity: 305245.3 MB = 298.0 GB (625142448 x 512)
Found 1 device(s).
reset_button: reg - ffee1104, value - 00000fe2
try to boot from image 0

SCSI read: device 0 block # 4096, count 2 ... 2 blocks read: OK
image header invalid
image 0 header invalid

SCSI read: device 0 block # 4096, count 0 ... 0 blocks read: OK
image length invalid, 6638ec1b
try to boot from image 1

SCSI read: device 0 block # 335872, count 2 ... 2 blocks read: OK
image header invalid
image 0 header invalid

SCSI read: device 0 block # 335872, count 0 ... 0 blocks read: OK
image length invalid, d68bf703
boot from hdd failed, try auto recovery now
SF: Detected S25FL128P_64K with page size 256 Bytes, erase size 64 KiB, sector size 64 KiB,

total 16 MiB
## Booting kernel from Legacy Image at 10000000 ...
Image Name: supertube01nor_v0.4.p13_106230
Image Type: ARM Linux Kernel Image (lzma compressed)
Data Size: 4411043 Bytes = 4.2 MiB
Load Address: 60000000
Entry Point:  60000000
Verifying Checksum ... OK
## Adjust Kernel size, FB size 0x40000000 size 256MB kernel entry 0x30000000,
Compress type: lzma compressed
Uncompressing Kernel Image ... OK

Starting kernel ...

Mach ID = 3506 ATAG 14800000 Kernel Entry 30000000Booting Linux on physical CPU 0xa00
Linux version 3.10.12 (buildbot@dev-c201) (gcc version 4.6.2 20110908 (prerelease) (Linaro

GCC 4.6-2011.09-1) ) #1 SMP Tue Jan 13 09:46:43 EST 2015
CPU: ARMv7 Processor [414fc091] revision 1 (ARMv7), cr=50c5387d
CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>ATAG at 14800000
Machine: Xcode6
Parse tag 54410001
Parse tag 54410009
Parse tag 54410007
Memory policy: ECC disabled, Data cache writealloc
On node 0 totalpages: 65280
free_area_init_node: node 0, pgdat 8065c680, node_mem_map 80696000
  Normal zone: 510 pages used for memmap
  Normal zone: 0 pages reserved
  Normal zone: 65280 pages, LIFO batch:15
xcode6_oscclk_adj_to_25M return: 0
PERCPU: Embedded 7 pages/cpu @80899000 s6912 r8192 d13568 u32768
pcpu-alloc: s6912 r8192 d13568 u32768 alloc=8*4096
pcpu-alloc: [0] 0 [0] 1
Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 64770
Kernel command line: earlyprintk loglevel=8 console=ttyS0,115200 initcall_debug=0 nosmp

ethaddr=d4:d9:19:60:06:4c ethaddr1=d4:d9:19:60:06:4d ethaddr2=d4:d9:19:60:06:4e

rootfstype=yaffs2 mem=255M button=0 bootver=15000003:ffffffff
Set eth0 MAC address to d4:d9:19:60:06:4c
PID hash table entries: 1024 (order: 0, 4096 bytes)
Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
Memory: 255MB = 255MB total
Memory: 252048k/252048k available, 9072k reserved, 0K highmem
Virtual kernel memory layout:
vector  : 0xffff0000 - 0xffff1000 ( 4 kB)
fixmap  : 0xfff00000 - 0xfffe0000 ( 896 kB)
vmalloc : 0x90000000 - 0xffff0000 (1791 MB)
lowmem  : 0x80000000 - 0x8ff00000 ( 255 MB)
pkmap : 0x7fe00000 - 0x80000000 ( 2 MB)
modules : 0x7f800000 - 0x7fe00000 ( 6 MB)
   .text : 0x80008000 - 0x803fbae0 (4047 kB)
   .init : 0x803fc000 - 0x80622b00 (2203 kB)
   .data : 0x80624000 - 0x8065d280 ( 229 kB)
   .bss : 0x8065d280 - 0x80695ccc ( 227 kB)
SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=2, Nodes=1
Hierarchical RCU implementation.
NR_IRQS:376
sched_clock: 32 bits at 100 Hz, resolution 10000000ns, wraps every 4294967286ms
Console: colour dummy device 80x30
UART0: Buffer RX 8f806000 TX 8f803000
UART1: Buffer RX 8f80c000 TX 8f807000
console [ttyS0] enabled
Calibrating delay loop... 1895.62 BogoMIPS (lpj=9478144)
pid_max: default: 32768 minimum: 301
Mount-cache hash table entries: 512
CPU: Testing write buffer coherency: ok
Kernel_init started
CPU0: thread -1, cpu 0, socket 10, mpidr 80000a00
Setting up static identity map for 0x802d6f80 - 0x802d6fcc
l2x0: Turn on L2 cache
L310 cache controller enabled
l2x0: 16 ways, CACHE_ID 0x410000c8, AUX_CTRL 0x7e470000, Cache size: 1048576 B
Brought up 1 CPUs
SMP: Total of 1 processors activated (1895.62 BogoMIPS).
CPU: All CPU(s) started in SVC mode.
devtmpfs: initialized
NET: Registered protocol family 16
DMA: preallocated 256 KiB pool for atomic coherent allocations
[InitPCIeHostBridge:206] pcie :0 as host PCIE_HOST_FB_MASK:1
[InitPCIeHostBridge:261]PCIEH:0: link is not up !
[InitPCIeHostBridge:206] pcie :1 as host PCIE_HOST_FB_MASK:fff00001
[InitPCIeHostBridge:261]PCIEH:1: link is not up !
bio: create slab <bio-0> at 0
SCSI subsystem initialized
libata version 3.00 loaded.
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
Switching to clocksource ARM Core Global Timer
FS-Cache: Loaded
NET: Registered protocol family 2
TCP established hash table entries: 2048 (order: 2, 16384 bytes)
TCP bind hash table entries: 2048 (order: 2, 16384 bytes)
TCP: Hash tables configured (established 2048 bind 2048)
TCP: reno registered
UDP hash table entries: 256 (order: 1, 8192 bytes)
UDP-Lite hash table entries: 256 (order: 1, 8192 bytes)
NET: Registered protocol family 1
squashfs: version 4.0 (2009/01/31) Phillip Lougher
NTFS driver 2.1.30 [Flags: R/W].
SGI XFS with security attributes, large block/inode numbers, no debug enabled
msgmni has been set to 492
Block layer SCSI generic (bsg) driver version 0.4 loaded (major 253)
io scheduler noop registered
io scheduler deadline registered
io scheduler cfq registered (default)
PROBE UART
XCODE_SERIAL_INIT
Xcode serial driver version 1.00
ttyS0 (irq = 85, address = 0xffeef400) is a builtin UART
ttyS1 (irq = 86, address = 0xffeef450) is a builtin UART
loop: module loaded
xcode-ahci-host0 xcode-ahci-host0: version 3.0
Init host controller
xcode-ahci-host0 xcode-ahci-host0: forcing PORTS_IMPL to 0x1
xcode-ahci-host0 xcode-ahci-host0: AHCI 0001.0300 32 slots 1 ports 3 Gbps 0x1 impl SATA mode
xcode-ahci-host0 xcode-ahci-host0: flags: ncq sntf pm led clo only pmp pio slum part
Activate ahci host
Request irq 58 80
scsi0 : xcode-ahci
ata1: SATA max UDMA/133 irq_stat 0x00400000, PHY RDY changed irq 58
xcode-ahci-host1 xcode-ahci-host1: forcing PORTS_IMPL to 0x1
xcode-ahci-host1 xcode-ahci-host1: AHCI 0001.0300 32 slots 1 ports 3 Gbps 0x1 impl SATA mode
xcode-ahci-host1 xcode-ahci-host1: flags: ncq sntf pm led clo only pmp pio slum part
Activate ahci host
scsi1 : xcode-ahci
ata2: SATA max UDMA/133 irq 58
SPI Flash ID = 12018
Creating 4 MTD partitions on "Morega SPI Flash":
0x000000000000-0x000000180000 : "uboot"
0x000000180000-0x0000007d0000 : "kernel"
0x0000007d0000-0x0000007f0000 : "Sparam"
0x0000007f0000-0x000000800000 : "Uparam"
tun: Universal TUN/TAP device driver, 1.6
tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
SynopGMAC: **********************************************************
SynopGMAC: * Driver :This is Synopsys GMAC-UNIV PCI-Network Driver
SynopGMAC: * Version :1.0
SynopGMAC: * Copyright :Copyright (c) 2007-2007 Synopsys, Inc
SynopGMAC: **********************************************************
SynopGMAC: Initializing synopsys GMAC interfaces ..
Turn on GTX clock
SynopGMAC: select RGMII interface for eth 1
SynopGMAC: Find ethernet phy device:0x01410e20.Phy index:19
SynopGMAC: tso buf at 9018f000, phy at 3e800000 size=0x2f5000
SynopGMAC: Find ethernet phy device:0x00000000.Phy index:0
SynopGMAC: tso buf at 9049b000, phy at 3e400000 size=0x2f5000
synopsis_init
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
Start: SDUH EHCI device registed to platform bus
END: SDUH EHCI device registed to platform bus
sduh-ehci sduh-ehci: initializing XCode-SOC USB Controller
SDUH_HCD_REG_BASE is  ffee2000
sduh-ehci sduh-ehci: Vixs On-Chip EHCI Host Controller
sduh-ehci sduh-ehci: new USB bus registered, assigned bus number 1
try reset SDUH controller
reset SDUH controller end
phy register setting end
enable interrupt mask end
try to read ehci cap register
try to read ehci params register
try to call ehci_halt
try to call ehci_init
sduh-ehci sduh-ehci: irq 64, io base 0xffee2000
sduh-ehci sduh-ehci: USB 2.0 started, EHCI 1.00
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
usb_hcd_sduh_probe: SDUH add success
ehci-pci: EHCI PCI platform driver
ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
Start: SDUH OHCI device registed to platform bus
END: SDUH OHCI device registed to platform bus
sduh-ohci sduh-ohci: initializing Xcode-SOC USB OHCI Controller
sduh-ohci sduh-ohci: Vixs On-Chip OHCI Host Controller
sduh-ohci sduh-ohci: new USB bus registered, assigned bus number 2
sduh-ohci sduh-ohci: irq 64, io mem 0xffee2000
enable interrupt mask endOHCI SDUH setup finished
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
uhci_hcd: USB Universal Host Controller Interface driver
ata2: SATA link down (SStatus 0 SControl 300)
xhci_register_plat 267
Start: SDUH XHCI device registed to platform bus
(__le32 *)0xc200=0xc0002540
GUSB3PIPECTL=0x010e0002
GCTL=0x30c01004
GUSB3PIPECTL (2) = 0x810e0002
END: SDUH XHCI device registed to platform bus
xhci-hcd xhci-hcd: xHCI Host Controller
xhci-hcd xhci-hcd: new USB bus registered, assigned bus number 3
xhci-hcd xhci-hcd: irq 63, io mem 0xffef2000
xHCI xhci_add_endpoint called for root hub
xHCI xhci_check_bandwidth called for root hub
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 1 port detected
xhci-hcd xhci-hcd: xHCI Host Controller
xhci-hcd xhci-hcd: new USB bus registered, assigned bus number 4
xHCI xhci_add_endpoint called for root hub
xHCI xhci_check_bandwidth called for root hub
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 1 port detected
usbcore: registered new interface driver usb-storage
xcode_wdt_init: Initializing XCode Watchdog
xcode_wdt_init:Init RESET_Button input.
xcode_wdt: XCODE Watchdog Timer: initial timeout 10 sec
device-mapper: ioctl: 4.24.0-ioctl (2013-01-15) initialised: dm-devel@redhat.com
xcsdh_init: Initializing XCode SD controller
*** supertube_led_init() ***
usbcore: registered new interface driver usbhid
usbhid: USB HID core driver
TCP: cubic registered
NET: Registered protocol family 10
sit: IPv6 over IPv4 tunneling driver
NET: Registered protocol family 17
VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 4
ThumbEE CPU extension supported.
Registering SWP/SWPB emulation handler
Almmc0: SD Status: Invalid Allocation Unit size.
mmc0: new high speed SD card at address b368
mmcblk0: mmc0:b368 SD 124 MiB
mmcblk0: unknown partition table
ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
ata1.00: ATA-7: ST3320620SV, 3.ACH, max UDMA/133
ata1.00: 625142448 sectors, multi 0: LBA48 NCQ (depth 31/32)
ata1.00: configured for UDMA/133
scsi 0:0:0:0: Direct-Access    ATA    ST3320620SV    3.AC PQ: 0 ANSI: 5
sd 0:0:0:0: Attached scsi generic sg0 type 0
sd 0:0:0:0: [sda] 625142448 512-byte logical blocks: (320 GB/298 GiB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sda: sda1
sd 0:0:0:0: [sda] Attached SCSI disk
Freeing unused kernel memory: 2200K (803fc000 - 80622000)
sleep 1 seconds,▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒
'shell=upgrade', continue...
S01: system init enter..................................................
proc on /proc type proc (rw,relatime)
sysfs on /sys type sysfs (rw,relatime)
init system time
Tue Jan 13 09:46:00 UTC 2015
reserved size 420M is OK
/dev/sda1: UUID="a107b9bd-a273-4822-a3cb-6c44aa2dc8ae" TYPE="ext4"
e2fsck 1.42.8 (20-Jun-2013)
Superblock last mount time is in the future.
      (by less than a day, probably due to the hardware clock being incorrectly set)  Fix?

yes

Superblock last write time is in the future.
      (by less than a day, probably due to the hardware clock being incorrectly set).

Fix? yes

/dev/sda1: clean, 5705/18612224 files, 1700705/74419712 blocks
Finished
e2fsck 1.42.8 (20-Jun-2013)
/dev/sda1: clean, 5705/18612224 files, 1700705/74419712 blocks
EXT3-fs (sda1): error: couldn't mount because of unsupported optional features (240)
EXT2-fs (sda1): error: couldn't mount because of unsupported optional features (240)
EXT4-fs (sda1): mounted filesystem with ordered data mode. Opts: (null)
umount: can't umount /dev/loop4: No such file or directory
Initializing random number generator... done.
Starting network...
SynopGMAC: Autonegotiation Complete, PHY_STATUS_REG=0x000078e9
SynopGMAC: Autonegotiation Complete, PHY_SPECIFIC_STATUS_REG=0x00007c40
SynopGMAC: take 1600 ms to auto-negotiation
SynopGMAC: Link up
SynopGMAC: Speed is 100 1
request irq 83
SynopGMAC: transmit desc at 0x90179000 0x3f970000
SynopGMAC: recv desc at 0x9018a000 0x3f96c000
SynopGMAC: enable HW checksum
SynopGMAC: enable TCP segmentation offload
udhcpc (v1.21.1) started
Sending discover...
Sending select for 192.168.1.126...
Lease of 192.168.1.126 obtained, lease time 86400
deleting routers
route: SIOCDELRT: No such process
adding dns 192.168.1.1
S95autorecovery
OK
Auto recover: get image,  order: #1-SD card, #2-USB, #3-network server
get_img_frm_sdcard() >>>
1
get_img_frm_sdcard(): found MicroSD card.
found SD card: mmcblk0
179
0

179
0
mknod: /dev/: File exists
mount: mounting /dev/ on /media failed: Invalid argument
umount: can't umount /media: Invalid argument
get_img_frm_sdcard() <<<
get_img_frm_USB() >>>

Welcome to Buildroot
Supertube60064C login: get_img_frm_USB() <<<
get_img_frm_network() >>>
http://192.168.10.100/firmwares/st_images/00010/recovery.bin http://supertubes-fw.gopro-

platform.com/firmwares/st_images/00010/recovery.bin
get_img_frm_network(): wget Firmware from

http://192.168.10.100/firmwares/st_images/00010/recovery.bin ...
--2015-01-13 09:46:07--  http://192.168.10.100/firmwares/st_images/00010/recovery.bin
Connecting to 192.168.10.100:80... failed: Connection timed out.
Retrying.

Got time from time.windows.com
--2019-06-20 07:25:02--  (try: 2)

http://192.168.10.100/firmwares/st_images/00010/recovery.bin
Connecting to 192.168.10.100:80... failed: Connection timed out.
Retrying.

--2019-06-20 07:25:09--  (try: 3)

http://192.168.10.100/firmwares/st_images/00010/recovery.bin
Connecting to 192.168.10.100:80... failed: Connection timed out.
Giving up.

get_img_frm_network(): wget Firmware from http://supertubes-fw.gopro-

platform.com/firmwares/st_images/00010/recovery.bin ...
--2019-06-20 07:25:14--  http://supertubes-fw.gopro-

platform.com/firmwares/st_images/00010/recovery.bin
Resolving supertubes-fw.gopro-platform.com... 99.84.231.93, 99.84.231.14, 99.84.231.84, ...
Connecting to supertubes-fw.gopro-platform.com|99.84.231.93|:80... connected.
HTTP request sent, awaiting response... 200 OK
Length: 35191398 (34M) [application/octet-stream]
Saving to: '/tmp/_tmp_image_'

0% [                                     ] 13,904    11.0KB/s

Watchdog:flag=1&1 count=59
2% [                                     ] 818,244    23.4KB/s  eta 21m

44sWatchdog:flag=1&1 count=59
3% [>                                     ] 1,305,192 14.9KB/s  eta 25m

55sWatchdog:flag=1&1 count=59
5% [=>                                  ] 1,970,640 22.7KB/s  eta 25m

33sWatchdog:flag=1&1 count=59
7% [==>                                  ] 2,802,788 25.8KB/s  eta 23m

22sWatchdog:flag=1&1 count=59
9% [==>                                  ] 3,478,608 20.2KB/s  eta 22m

59sWatchdog:flag=1&1 count=59
11% [===>                                  ] 4,022,676 18.7KB/s  eta 23m 18s

高手给看看，或给一个编程器固件，再刷。哪不对呀

账号		自动登录	找回密码
密码			立即注册

高手们进，看看是什么东西

本帖子中包含更多资源

评分

点评

点评

本帖子中包含更多资源

点评

点评

点评

本帖子中包含更多资源