R8500 救砖求助-CFE好还是坏了

k1mxn

启动后信息如下：
这个CFE算好的还是坏的？？

一直按着ctrl+c 也无法中断启动，后面就没有任何信息了

Digital core power voltage set to 1.05V
Decompressing...done
Digital core power voltage set to 1.05V

SHMOO VER 1.13

CFE for Foxconn Router R7800/R8500 version: v1.0.5
Build Date: Tue Jun 30 20:39:15 CST 2015
Init Arena
Init Devs.
Boot up from NAND flash...
Bootcode Boot partition size = 524288(0x80000)
DDR Clock: 800 MHz
Info: DDR frequency set from clkfreq=1400,*800*
et2: Broadcom BCM47XX 10/100/1000 Mbps Ethernet Controller 7.14.121 (r552363)
CPU type 0x0: 1400MHz
Tot mem: 524288 KBytes

zyguowei

ADDR

    0000000000111111111122222222223333333333444444444455555555556666
    0123456789012345678901234567890123456789012345678901234567890123
00 ++++++++++++++++++++S++++++++++X++++++++++++++++++++++++++++++++

Decompressing...done


CFE for Foxconn Router R7800/R8500 version: v1.0.5
Build Date: Tue Jun 30 20:39:15 CST 2015
Init Arena
Init Devs.
Boot up from NAND flash...
Bootcode Boot partition size = 524288(0x80000)
DDR Clock: 800 MHz
Info: DDR frequency set from clkfreq=1400,*800*
et2: Broadcom BCM47XX 10/100/1000 Mbps Ethernet Controller 7.14.121 (r552363)
CPU type 0x0: 1400MHz
Tot mem: 524288 KBytes

Device eth0:  hwaddr 9C-3D-CF-0F-DC-6C, ipaddr 192.168.1.1, mask 255.255.255.0
        gateway not set, nameserver not set
Checking crc...Loader:raw Filesys:raw Dev:nflash0.os File: Optionsnull)
Loading: ..... 5470272 bytes read
Entry at 0x00008000
Closing network.
Starting program at 0x00008000
[    2.130000] console [ttyS0] enabled, bootconsole disabled
[    2.140000] serial8250.0: ttyS1 at MMIO 0x18000400 (irq = 117) is a 16550
[    2.150000] brd: module loaded
[    2.160000] loop: module loaded
[    2.160000] pflash: found no supported devices
[    2.160000] bcmsflash: found no supported devices
[    2.740000] Boot partition size = 524288(0x80000)
[    2.750000] lookup_nflash_rootfs_offset: offset = 0x200000
[    2.760000] nflash: squash filesystem with lzma found at block 32
[    2.760000] Creating 17 MTD partitions on "nflash":
[    2.770000] 0x000000000000-0x000000080000 : "boot"
[    2.770000] 0x000000080000-0x000000200000 : "nvram"
[    2.790000] 0x000000200000-0x000006f00000 : "linux"
[    3.280000] 0x00000041ab90-0x000006f00000 : "rootfs"
[    3.290000] 0x000007400000-0x000007480000 : "board_data"
[    3.300000] 0x000007480000-0x000007580000 : "OT1"
[    3.310000] 0x000007580000-0x000007680000 : "OT2"
[    3.320000] 0x000007680000-0x000007940000 : "T_Meter1"
[    3.330000] 0x000007940000-0x000007c00000 : "T_Meter2"
[    3.350000] 0x000007c00000-0x000007c80000 : "ML1"
[    3.360000] 0x000007c80000-0x000007d00000 : "ML2"
[    3.370000] 0x000007d00000-0x000007d80000 : "ML3"
[    3.380000] 0x000007d80000-0x000007e00000 : "ML4"
[    3.380000] 0x000007e00000-0x000007e80000 : "ML5"
[    3.390000] 0x000007e80000-0x000007f00000 : "ML6"
[    3.400000] 0x000007f00000-0x000007f80000 : "ML7"
[    3.410000] 0x000007f80000-0x000008000000 : "DebugMsg"
[    3.410000] PPP generic driver version 2.4.2
[    3.420000] PPP MPPE Compression module registered
[    3.420000] NET: Registered protocol family 24
[    3.430000] PPPoL2TP kernel driver, V0.17
[    3.430000] tun: Universal TUN/TAP device driver, 1.6
[    3.440000] tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>

k1mxn

zyguowei 发表于 2021-10-24 18:55
ADDR

    0000000000111111111122222222223333333333444444444455555555556666

什么意思呢？？？

zyguowei

k1mxn 发表于 2021-10-24 19:42
什么意思呢？？？

正常的TTL码给你参考，没别的意思。

jiaoxiaopo

解决了没我的也是这个