|
楼主 |
发表于 2019-6-3 17:15
|
显示全部楼层
本帖最后由 lupus721 于 2019-6-3 17:24 编辑
虽然不知道有什么用,但是说不定有看懂的呢
-----------------------------
[ 0.000000] Linux version 3.10.14+ (fc@server) (gcc version 4.8.3 (OpenWrt/Linaro GCC 4.8-2014.04 r632) ) #57 Fri Jan 6 15:17:38 CST 2017
[ 0.000000]
[ 0.000000] The CPU feqenuce set to 575 MHz
[ 0.000000]
[ 0.000000] MIPS CPU sleep mode enabled.
[ 0.000000] CPU0 revision is: 00019655 (MIPS 24KEc)
[ 0.000000] Software DMA cache coherency
[ 0.000000] Determined physical RAM map:
[ 0.000000] memory: 04000000 @ 00000000 (usable)
[ 0.000000] Initrd not found or empty - disabling initrd
[ 0.000000] Zone ranges:
[ 0.000000] Normal [mem 0x00000000-0x03ffffff]
[ 0.000000] Movable zone start for each node
[ 0.000000] Early memory node ranges
[ 0.000000] node 0: [mem 0x00000000-0x03ffffff]
[ 0.000000] Primary instruction cache 64kB, 4-way, VIPT, linesize 32 bytes.
[ 0.000000] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 16256
[ 0.000000] Kernel command line: console=ttyS1,57600n8 root=/dev/mtdblock5 rootfstype=squashfs,jffs2
[ 0.000000] PID hash table entries: 256 (order: -2, 1024 bytes)
[ 0.000000] Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
[ 0.000000] Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
[ 0.000000] Writing ErrCtl register=0007400e
[ 0.000000] Readback ErrCtl register=0007400e
[ 0.000000] Memory: 60384k/65536k available (3236k kernel code, 5152k reserved, 860k data, 188k init, 0k highmem)
[ 0.000000] NR_IRQS:128
[ 0.000000] console [ttyS1] enabled
[ 0.100000] Calibrating delay loop... 385.02 BogoMIPS (lpj=770048)
[ 0.140000] pid_max: default: 32768 minimum: 301
[ 0.144000] Mount-cache hash table entries: 512
[ 0.148000] NET: Registered protocol family 16
[ 0.152000] RALINK_GPIOMODE = 56050404
[ 0.156000] RALINK_GPIOMODE = 56040404
[ 0.256000] ***** Xtal 40MHz *****
[ 0.260000] start PCIe register access
[ 0.760000] RALINK_RSTCTRL = 2400000
[ 0.764000] RALINK_CLKCFG1 = fdbfffc0
[ 0.768000]
[ 0.768000] *************** MT7628 PCIe RC mode *************
[ 1.268000] PCIE0 no card, disable it(RST&CLK)
[ 1.272000]
[ 1.272000] mt7628 gpio init
[ 1.304000] bio: create slab <bio-0> at 0
[ 1.308000] usbcore: registered new interface driver usbfs
[ 1.312000] usbcore: registered new interface driver hub
[ 1.316000] usbcore: registered new device driver usb
[ 1.320000] cfg80211: Calling CRDA to update world regulatory domain
[ 1.324000] Switching to clocksource Ralink Systick timer
[ 1.328000] NET: Registered protocol family 2
[ 1.340000] TCP established hash table entries: 512 (order: 0, 4096 bytes)
[ 1.352000] TCP bind hash table entries: 512 (order: -1, 2048 bytes)
[ 1.364000] TCP: Hash tables configured (established 512 bind 512)
[ 1.376000] TCP: reno registered
[ 1.384000] UDP hash table entries: 256 (order: 0, 4096 bytes)
[ 1.396000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[ 1.408000] NET: Registered protocol family 1
[ 1.416000] MTK/Ralink EHCI/OHCI init.
[ 1.424000] >>>>>>>>>>register my wifi led<<<<<<<<<<<<<<<<<
[ 1.440000] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 1.452000] ufsd: driver (8.6, Dec 3 2016 16:46:52, LBD=ON, delalloc, ioctl, bdi) loaded at (null)
[ 1.452000] NTFS (with native replay) support included
[ 1.452000] optimized: speed
[ 1.452000] Built_for__Asus_n65u_2012-03-29
[ 1.452000]
[ 1.496000] jffs2: version 2.2. (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[ 1.516000] msgmni has been set to 117
[ 1.524000] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 253)
[ 1.540000] io scheduler noop registered (default)
[ 1.556000] Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled
[ 1.572000] serial8250: ttyS0 at MMIO 0x10000d00 (irq = 21) is a 16550A
[ 1.584000] serial8250: ttyS1 at MMIO 0x10000c00 (irq = 20) is a 16550A
[ 1.596000] RALINK_REG_PIO6332DIR=0
[ 1.604000] RALINK_REG_PIO6332DIR=100
[ 1.612000] RALINK_REG_PIO6332DATA=cf
[ 1.620000] RALINK_REG_PIO6332DATA=1cf
[ 1.628000] Ralink gpio driver initialized
[ 1.636000] Pwm Control Driver Init
[ 1.644000] flash manufacture id: c2, device id 20 18
[ 1.652000] MX25L12805D(c2 2018c220) (16384 Kbytes)
[ 1.664000] mtd .name = raspi, .size = 0x01000000 (16M) .erasesize = 0x00010000 (64K) .numeraseregions = 0
[ 1.684000] Creating 6 MTD partitions on "raspi":
[ 1.692000] 0x000000000000-0x000001000000 : "ALL"
[ 1.704000] 0x000000000000-0x000000030000 : "Bootloader"
[ 1.716000] 0x000000030000-0x000000040000 : "config"
[ 1.728000] 0x000000040000-0x000000050000 : "Factory"
[ 1.736000] 0x000000050000-0x000000850000 : "firmware"
[ 1.748000] ih.hcrc=512fa85e,ih.dcrc=4c73acff,ih.size=74ffc0,ih_ksz=6d000080
[ 1.764000] offset=500,len=750000,part->mtd.size=0,hdr.kern_size=800000,name=(null),hdr.size=0
[ 1.780000] 0x0000001c0000-0x0000007b0000 : "rootfs"
[ 1.792000] mtd: partition "rootfs_data" created automatically, ofs=0x0, len=0x0
[ 1.808000] mtd: partition "rootfs_data" created automatically, ofs=0x7b0000, len=0xa0000
[ 1.824000] 0x0000007b0000-0x000000850000 : "rootfs_data"
[ 1.836000] 0x000000850000-0x000001000000 : "firmware2"
[ 1.848000] rdm_major = 251
[ 1.852000] GMAC1_MAC_ADRH -- : 0x0000c80e
[ 1.860000] GMAC1_MAC_ADRL -- : 0x7757628f
[ 1.868000] Ralink APSoC Ethernet Driver Initilization. v3.1 256 rx/tx descriptors allocated, mtu = 1500!
[ 1.888000] GMAC1_MAC_ADRH -- : 0x0000c80e
[ 1.896000] GMAC1_MAC_ADRL -- : 0x7757628f
[ 1.904000] PROC INIT OK!
[ 1.912000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 1.924000] ehci-pci: EHCI PCI platform driver
[ 1.932000] ehci-platform: EHCI generic platform driver
[ 1.964000] ******MT7628 mtk phy
[ 1.968000] *****run project phy.
[ 1.984000] FM_OUT value: u4FmOut = 0(0x00000000)
[ 2.000000] FM_OUT value: u4FmOut = 130(0x00000082)
[ 2.008000] FM detection done! loop = 1
[ 2.024000] SR calibration value u1SrCalVal = 6
[ 2.032000] *********Execute mt7628_phy_init!!
[ 2.040000] ehci-platform ehci-platform: EHCI Host Controller
[ 2.052000] ehci-platform ehci-platform: new USB bus registered, assigned bus number 1
[ 2.068000] ehci-platform ehci-platform: irq 18, io mem 0x101c0000
[ 2.092000] ehci-platform ehci-platform: USB 2.0 started, EHCI 1.00
[ 2.104000] hub 1-0:1.0: USB hub found
[ 2.112000] hub 1-0:1.0: 1 port detected
[ 2.120000] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[ 2.152000] *********Execute mt7628_phy_init!!
[ 2.160000] ohci-platform ohci-platform: Generic Platform OHCI Controller
[ 2.172000] ohci-platform ohci-platform: new USB bus registered, assigned bus number 2
[ 2.188000] ohci-platform ohci-platform: irq 18, io mem 0x101c1000
[ 2.260000] hub 2-0:1.0: USB hub found
[ 2.268000] hub 2-0:1.0: 1 port detected
[ 2.276000] TCP: cubic registered
[ 2.284000] NET: Registered protocol family 10
[ 2.292000] NET: Registered protocol family 17
[ 2.300000] 8021q: 802.1Q VLAN Support v1.8
[ 2.312000] ralink_nvram: unable to register character device
[ 2.324000] registered taskstats version 1
[ 2.340000] VFS: Mounted root (squashfs filesystem) readonly on device 31:5.
[ 2.352000] Freeing unused kernel memory: 188K (80401000 - 80430000)
[ 2.492000] usb 1-1: new high-speed USB device number 2 using ehci-platform
procd: Console is alive
[ 4.384000] SCSI subsystem initialized
[ 4.400000] usb-storage 1-1:1.0: USB Mass Storage device detected
[ 4.412000] scsi0 : usb-storage 1-1:1.0
[ 4.420000] usbcore: registered new interface driver usb-storage
procd: - preinit -
[ 5.324000] Raeth v3.1 (Tasklet)
[ 5.332000]
[ 5.332000] phy_tx_ring = 0x03f96000, tx_ring = 0xa3f96000
[ 5.344000]
[ 5.344000] phy_rx_ring0 = 0x03f97000, rx_ring0 = 0xa3f97000
[ 5.376000] GMAC1_MAC_ADRH -- : 0x0000c80e
[ 5.384000] GMAC1_MAC_ADRL -- : 0x7757628f
[ 5.392000] RT305x_ESW: Link Status Changed
[ 5.420000] scsi 0:0:0:0: Direct-Access General USB Flash Disk 1.00 PQ: 0 ANSI: 2
/etc/preinit: line 1: netmsg: not found
[ 5.456000] sd 0:0:0:0: [sda] 123904000 512-byte logical blocks: (63.4 GB/59.0 GiB)
Press the [f] ke[ 5.484000] sd 0:0:0:0: [sda] Write Protect is off
y and hit [enter] to enter failsafe mode
Press the [1], [2], [3[ 5.504000] sd 0:0:0:0: [sda] No Caching mode page found
] or [4] key and[ 5.516000] sd 0:0:0:0: [sda] Assuming drive cache: write through
hit [enter] to select the debug[ 5.532000] sd 0:0:0:0: [sda] No Caching mode page found
level
[ 5.544000] sd 0:0:0:0: [sda] Assuming drive cache: write through
[ 5.560000] sda: sda1
[ 5.572000] sd 0:0:0:0: [sda] No Caching mode page found
[ 5.580000] sd 0:0:0:0: [sda] Assuming drive cache: write through
[ 5.592000] sd 0:0:0:0: [sda] Attached SCSI removable disk
kmod: ran 1 iterations
[ 9.060000] jffs2: notice: (269) jffs2_build_xattr_subsystem: complete building xattr subsystem, 1 of xdatum (0 unchecked, 0 orphan) and 10 of xref (0 dead, 0 orphan) found.
block: extroot: no root or overlay mount defined
jffs2 is ready
jffs2 is ready
[ 9.136000] jffs2: notice: (266) jffs2_build_xattr_subsystem: complete building xattr subsystem, 1 of xdatum (0 unchecked, 0 orphan) and 10 of xref (0 dead, 0 orphan) found.
switching to overlay
/etc/preinit: line 1: grep: not found
procd: - early -
procd: - ubus -
procd: - init -
Please press Enter to activate this console.
procd: - init complete -
|
|