openwer 主板 专业AP改造 做工质量上乘

fastwlan

Atheros AR7141
16MB 固件
64MB 内存
Atheros AR9220(mini pci) 2T2R  300M
有线网络口千兆

http://item.taobao.com/item.htm?id=13560018371 可以带刀

fastwlan

2# zxbmuyu


专业AP主板

hackant

菜鸟 可以买来 当路由器用吗？我家里有个坏的思科。。正好 塞这个主板

fastwlan

4# hackant
刷OPENWET 可以当无线路由

fclql

怎么不弄专业路由呢？  弄个神器出来量产啊

H2O

也是680mhz的

huangfc_1

不是吧，你发错地方了吧

lindianfeng

我搞定了，刷上 openwrt了。

一会上个新的。

lindianfeng

我编译了一个固件，刷上了。

大家看看吧，板子的质量很好，带的卡 是双频的， ar9220 呵呵。

lindianfeng

另外的图

lindianfeng

[    0.000000] Linux version 2.6.39.4 (kaka@kaka-dev) (gcc version 4.5.4 20110808 (prerelease) (Linaro GCC 4.5-2011.08) ) #1 Fri Dec 30 15:09:55 CST 2011
[    0.000000] prom: fw_arg0=00000002, fw_arg1=80050020, fw_arg2=80050000, fw_arg3=00000010
[    0.000000] MyLoader: sysp=00000000, boardp=240a001e, parts=0341d025
[    0.000000] bootconsole [early0] enabled
[    0.000000] CPU revision is: 00019374 (MIPS 24Kc)
[    0.000000] SoC: Atheros AR7141 rev 2
[    0.000000] Clocks: CPU:680.000MHz, DDR:340.000MHz, AHB:170.000MHz, Ref:40.000MHz
[    0.000000] Determined physical RAM map:
[    0.000000]  memory: 04000000 @ 00000000 (usable)
[    0.000000] Initrd not found or empty - disabling initrd
[    0.000000] Zone PFN ranges:
[    0.000000]   Normal   0x00000000 -> 0x00004000
[    0.000000] Movable zone start PFN for each node
[    0.000000] early_node_map[1] active PFN ranges
[    0.000000]     0: 0x00000000 -> 0x00004000
[    0.000000] On node 0 totalpages: 16384
[    0.000000] free_area_init_node: node 0, pgdat 802bd750, node_mem_map 81000000
[    0.000000]   Normal zone: 128 pages used for memmap
[    0.000000]   Normal zone: 0 pages reserved
[    0.000000]   Normal zone: 16256 pages, LIFO batch:3
[    0.000000] pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768
[    0.000000] pcpu-alloc: [0] 0
[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 16256
[    0.000000] Kernel command line:  board=EAP7660D console=ttyS0,115200 ethaddr=00.03.7f.ff.ff.fe rootfstype=squashfs,jffs2 noinitrd
[    0.000000] PID hash table entries: 256 (order: -2, 1024 bytes)
[    0.000000] Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
[    0.000000] Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
[    0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
[    0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes
[    0.000000] Writing ErrCtl register=00000002
[    0.000000] Readback ErrCtl register=00000002
[    0.000000] Memory: 61828k/65536k available (2030k kernel code, 3708k reserved, 393k data, 188k init, 0k highmem)
[    0.000000] SLUB: Genslabs=9, HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[    0.000000] NR_IRQS:80
[    0.000000] Calibrating delay loop... 452.19 BogoMIPS (lpj=2260992)
[    0.060000] pid_max: default: 32768 minimum: 301
[    0.060000] Mount-cache hash table entries: 512
[    0.070000] NET: Registered protocol family 16
[    0.070000] MIPS: machine is Senao EAP7660D
[    0.080000] ar71xx: using random MAC address for eth0
[    0.570000] registering PCI controller with io_map_base unset
[    0.580000] bio: create slab <bio-0> at 0
[    0.580000] pci 0000:00:00.0: [0700:1107] type 0 class 0x000000
[    0.580000] pci 0000:00:00.0: reg 10: [mem 0x00000000-0x0fffffff pref]
[    0.580000] pci 0000:00:00.0: reg 14: [io  0x0000-0x00ff]
[    0.580000] pci 0000:00:00.0: supports D1 D2
[    0.580000] pci 0000:00:00.0: PME# supported from D0 D1 D2 D3hot
[    0.580000] pci 0000:00:00.0: PME# disabled
[    0.580000] pci 0000:00:11.0: [168c:0029] type 0 class 0x000280
[    0.580000] pci 0000:00:11.0: reg 10: [mem 0x00000000-0x0000ffff]
[    0.580000] pci 0000:00:11.0: PME# supported from D0 D3hot
[    0.580000] pci 0000:00:11.0: PME# disabled
[    0.580000] pci 0000:00:11.0: BAR 0: assigned [mem 0x10000000-0x1000ffff]
[    0.590000] pci 0000:00:11.0: BAR 0: set to [mem 0x10000000-0x1000ffff] (PCI address [0x10000000-0x1000ffff])
[    0.590000] PCI: mapping irq 72 to pin1@0000:00:11.0
[    0.600000] Switching to clocksource MIPS
[    0.600000] NET: Registered protocol family 2
[    0.610000] IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
[    0.610000] TCP established hash table entries: 2048 (order: 2, 16384 bytes)
[    0.620000] TCP bind hash table entries: 2048 (order: 1, 8192 bytes)
[    0.620000] TCP: Hash tables configured (established 2048 bind 2048)
[    0.630000] TCP reno registered
[    0.630000] UDP hash table entries: 256 (order: 0, 4096 bytes)
[    0.640000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[    0.640000] NET: Registered protocol family 1
[    0.650000] PCI: CLS 0 bytes, default 32
[    0.660000] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[    0.660000] JFFS2 version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[    0.670000] msgmni has been set to 120
[    0.680000] io scheduler noop registered
[    0.680000] io scheduler deadline registered (default)
[    0.690000] Serial: 8250/16550 driver, 1 ports, IRQ sharing disabled
[    0.710000] serial8250.0: ttyS0 at MMIO 0x18020000 (irq = 11) is a 16550A
[    0.720000] console [ttyS0] enabled, bootconsole disabled
[    0.730000] Atheros AR71xx SPI Controller driver version 0.2.4
[    0.740000] m25p80 spi0.0: found s25fl129p1, expected m25p80
[    0.750000] m25p80 spi0.0: s25fl129p1 (16384 Kbytes)
[    0.750000] Searching for RedBoot partition table in spi0.0 at offset 0xfe0000
[    0.840000] 6 RedBoot partitions found on MTD device spi0.0
[    0.850000] Creating 6 MTD partitions on "spi0.0":
[    0.850000] 0x000000000000-0x000000040000 : "RedBoot"
[    0.860000] 0x000000040000-0x000000120000 : "kernel"
[    0.860000] 0x000000120000-0x000000fe0000 : "rootfs"
[    0.870000] mtd: partition "rootfs" set to be root filesystem
[    0.880000] mtd: partition "rootfs_data" created automatically, ofs=330000, len=CB0000
[    0.880000] 0x000000330000-0x000000fe0000 : "rootfs_data"
[    0.890000] 0x000000fe0000-0x000000fef000 : "FIS directory"
[    0.900000] 0x000000fef000-0x000000ff0000 : "RedBoot config"
[    0.900000] 0x000000ff0000-0x000001000000 : "boardconfig"
[    0.930000] ag71xx_mdio: probed
[    0.930000] eth0: Atheros AG71xx at 0xb9000000, irq 4
[    1.230000] eth0: connected to PHY at ag71xx-mdio.0:00 [uid=004dd04e, driver=Generic PHY]
[    1.240000] Atheros AR71xx hardware watchdog driver version 0.1.0
[    1.240000] ar71xx-wdt: timeout=15 secs (max=25)
[    1.240000] TCP westwood registered
[    1.250000] NET: Registered protocol family 17
[    1.250000] 802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>
[    1.260000] All bugs added by David S. Miller <davem@redhat.com>
[    1.270000] VFS: Mounted root (squashfs filesystem) readonly on device 31:2.
[    1.280000] Freeing unused kernel memory: 188k freed
[    3.220000] Button Hotplug driver version 0.4.1
[    5.230000] ar71xx: pll_reg 0xb8050010: 0x1099
[    5.230000] eth0: link up (100Mbps/Full duplex)
[    5.540000] eth0: link down
[    7.170000] Compat-wireless backport release: compat-wireless-2011-11-29
[    7.180000] Backport based on wireless-testing.git master-2011-12-01
[    7.260000] cfg80211: Calling CRDA to update world regulatory domain
[    7.450000] cfg80211: World regulatory domain updated:
[    7.450000] cfg80211:     (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
[    7.460000] cfg80211:     (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[    7.470000] cfg80211:     (2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[    7.480000] cfg80211:     (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[    7.480000] cfg80211:     (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[    7.490000] cfg80211:     (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[    7.930000] usbcore: registered new interface driver usbfs
[    7.940000] usbcore: registered new interface driver hub
[    7.950000] usbcore: registered new device driver usb
[    8.870000] PCI: Enabling device 0000:00:11.0 (0000 -> 0002)
[   10.430000] ath: EEPROM regdomain: 0x0
[   10.430000] ath: EEPROM indicates default country code should be used
[   10.430000] ath: doing EEPROM country->regdmn map search
[   10.430000] ath: country maps to regdmn code: 0x3a
[   10.430000] ath: Country alpha2 being used: US
[   10.430000] ath: Regpair used: 0x3a
[   10.440000] ieee80211 phy0: Selected rate control algorithm 'minstrel_ht'
[   10.440000] Registered led device: ath9k-phy0
[   10.440000] ieee80211 phy0: Atheros AR9280 Rev:2 mem=0xb0000000, irq=72
[   10.450000] cfg80211: Calling CRDA for country: US
[   10.550000] cfg80211: Regulatory domain changed to country: US
[   10.560000] cfg80211:     (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
[   10.560000] cfg80211:     (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2700 mBm)
[   10.570000] cfg80211:     (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 1700 mBm)
[   10.580000] cfg80211:     (5250000 KHz - 5330000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[   10.590000] cfg80211:     (5490000 KHz - 5600000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[   10.600000] cfg80211:     (5650000 KHz - 5710000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[   10.600000] cfg80211:     (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 3000 mBm)
[   10.650000] PPP generic driver version 2.4.2
[   10.910000] ip_tables: (C) 2000-2006 Netfilter Core Team
[   11.080000] NET: Registered protocol family 24
[   11.190000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[   11.260000] nf_conntrack version 0.5.0 (969 buckets, 3876 max)
[   11.670000] xt_time: kernel timezone is -0000
[   11.970000] Atheros(R) L2 Ethernet Driver - version 2.2.3
[   11.970000] Copyright (c) 2007 Atheros Corporation.
[   12.070000] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[   14.010000] device eth0 entered promiscuous mode
[   14.520000] ar71xx: pll_reg 0xb8050010: 0x1099
[   14.520000] eth0: link up (100Mbps/Full duplex)

、内核的日志。

lindianfeng

刷的过程：



1、进入 redboot
出现 redboot> 后执行 fis list 查看分区信息，把这个信息拷贝下来存到文件中备用。

2、在电脑上架设一个 tftp server ，软件可以采用 tftpd32 将固件放到 tftp 个根目录下

3、在 redboot中 执行 ip_address -l 192.168.10.100 回车指定 路由 ip地址，再执行 ip_address -l 192.168.10.2 回车（tftp server所在电脑的地址）
   然后执行 fis init ，进行分区的初始化，出现提示 输入 y
   
RedBoot> fis init
About to initialize [format] FLASH image system - continue (y/n)? y
*** Initialize FLASH Image System
... Erase from 0xbffe0000-0xbfff0000: .
... Program from 0x83ff0000-0x84000000 at 0xbffe0000: .


4、在 redboot中 执行 load  -v -r -b 0x80060000 openwrt-ar71xx-shuige-kernel.bin 回车，装载内核

RedBoot> load  -v -r -b 0x80060000 openwrt-ar71xx-shuige-kernel.bin
Using default protocol (TFTP)
|
Raw file loaded 0x80060000-0x8013ffff, assumed entry at 0x80060000


5、在 redboot中 执行 fis create -r 0x80060000 -e 0x80060000  -l 0xE0000 kernel 回车， 创建 kernel分区

RedBoot> fis create -r 0x80060000 -e 0x80060000  -l 0xE0000 kernel
... Erase from 0xbf040000-0xbf120000: ..............
... Program from 0x80060000-0x80140000 at 0xbf040000: ..............
... Erase from 0xbffe0000-0xbfff0000: .
... Program from 0x83ff0000-0x84000000 at 0xbffe0000: .


6、在 redboot中 执行 load -r -b 0x8006CC00 openwrt-ar71xx-shuige-rootfs-squashfs.bin 回车，装载root fs

RedBoot> load -r -b 0x8006CC00 openwrt-ar71xx-shuige-rootfs-squashfs.bin
Using default protocol (TFTP)
Raw file loaded 0x8006cc00-0x802ccbff, assumed entry at 0x8006cc00


7、在 redboot中 执行 fis create rootfs  回车，创建 rootfs

RedBoot> fis create rootfs
... Erase from 0xbf120000-0xbf380000: ......................................
... Program from 0x8006cc00-0x802ccc00 at 0xbf120000: ..........................
............
... Erase from 0xbffe0000-0xbfff0000: .
... Program from 0x83ff0000-0x84000000 at 0xbffe0000: .


8、在 redboot中 执行 fconfig 回车，其他都选择默认，当需要输入脚本的时候 输入
   
    fis load -l kernel 回车
        exec -c "board=PB44" 回车
        回车
       
        当提示是否保存是 输入 y
       
       
        RedBoot> fconfig
Run script at boot: true
Boot script:
.. fis load -l kernel
.. exec -c "board=PB44"
Enter script, terminate with empty line
>> fis load -l kernel
>> exec -c "board=PB44"
>>
Boot script timeout (1000ms resolution): 3
Use BOOTP for network configuration: false
Gateway IP address: 192.168.10.1
Local IP address: 192.168.10.100
Local IP address mask: 255.255.255.0
Default server IP address: 192.168.10.2
Console baud rate: 115200
GDB connection port: 9000
Force console for special debug messages: false
Network debug at boot time: false
Update RedBoot non-volatile configuration - continue (y/n)? y
... Erase from 0xbffe0000-0xbfff0000: .
... Program from 0x83ff0000-0x84000000 at 0xbffe0000: .
       
9、输入 reset 回车 重新启动路由

RedBoot> reset
... Resetting.+

fastwlan

高手 终于有看到OP了