DIR-825 B1固件刷新的问题

CyrixIII

进入825的恢复模式，选择好固件，然后点刷新之后就没反应了，在IE下什么变化都没有，在Chrom下看到固件上传进去，就等192.168.0.1返回信息，然后就是一直等待，电源那个橙色的灯一直是闪烁状态
半个小时还没变化，F5刷新一下页面，在上传固件，就提示固件和硬件不符，始终无法刷新
折腾了2个多小时，重启无数次，都还是没刷进去，无论是刷原厂固件还是Openwrt都是这样

andyxie5585

恢复模式下上傳固件有進度條的，沒有進度條就是固件不適合，換其它的吧。

CyrixIII

andyxie5585 发表于 2012-2-20 09:24
恢复模式下上傳固件有進度條的，沒有進度條就是固件不適合，換其它的吧。

用Google Chorm浏览器能看到进度，跳到100%就没反应了
另外刷原厂固件也是这样，基本就是固件上传上去之后，设备没有返回信息

andyxie5585

原廠固件是DIR-825 B1_fw2.05_1嗎？

CyrixIII

andyxie5585 发表于 2012-2-20 09:40
原廠固件是DIR-825 B1_fw2.05_1嗎？

在DLink台湾官网下的，DIR825B1_FW205EAB05.bin

CyrixIII

不知道刷新固件跟浏览器有没有关系，看Openwrt官网上DIR-825的专题页面有这样的说法
http://wiki.openwrt.org/toh/d-link/dir-825

Installation using firmware update page
Note: Since original Firmware 2.05WW Build: 05Beta01 it is not possible to flash OpenWrt via the firmware update page. (worked on a B2 revision with Ubuntu's Firefox in 2.05NA and 2.06NA) It looks like Firmware 2.01EU behaves the same way. Please use the firmware recovery mode instead.

1. Login into the factory D-Link firmware web-interface as usual. Default procedure for the freshly purchased router is:
    1. Set the static IP 192.168.0.100/24 on the PC
    2. With any web browser go to http://192.168.0.1/, use "admin" as the username, and "" as the password(leave the field blank).
2. Proceed into the firmware update page, click "Browse" and select your OpenWrt image file (openwrt-ar71xx-generic-dir-825-b1-squashfs-factory.bin)
3. Click "Update" and let the router reflash itself.
4. Device should now reboot itself and boot up the OpenWrt.
5. Give the router some time to finish firstboot tasks (initial configuration, jffs2 initialization, e.t.c.).
6. The router's power LED should blink orange during bootup, as soon as it stops flashing, you can connect to it
7. obtain new IP from the router via DHCP and follow firstlogin
Installation using firmware recovery mode
Note: The firmware recovery mode has following quirks:

· If you have a Windows machine available you can use Microsoft Internet Explorer 7 ( a Windows running on a VM, like VMware, does not work)
· If you are running Linux you can:
  · Set your interface to 100Mbps using sudo ethtool -s eth0 speed 100 autoneg off, install IE7 in Wine and use it to flash.
  · Later models (or some hardware combinations) may need sudo ethtool -s eth0 speed 100 duplex half autoneg off (e.g. B2, FW ver 2.05EU).
  · Use the following script.
· If you are running MacOS you can use Google Chrome Opera
1. Get into the D-Link recovery console with the steps below:
    1. While powering up the router, press and hold the reset button until the power LED starts blinking orange (usually takes around 45 (forty-five) seconds )
    2. Set a static IP on your PC to 192.168.0.100/24
    3. connect to http://192.168.0.1, mind the quirks!
2. Click "Browse" and select your OpenWrt image file (openwrt-ar71xx-dir-825-b1-squashfs-factory.bin, this binary image is available in the Backfire 10.03.1rc1 download directory and above)
3. Click "Update" and let router flash the image (don't worry if it reboots before it reaches 100%). The page should display "Device is Upgrading the Firmware" in blue letters with the current percentage in red (with an incompatible Browser it doesn't).
4. The router's power LED should blink orange during bootup, as soon as it stops flashing, you can connect to it
5. obtain new IP from the router via DHCP and follow firstlogin

先尝试把固件由2.05在正常模式下web刷新到2.0，但是还是无法按方案1的说法在web下更新
然后按照方案2进入恢复模式，但是就像上面说的，刷新无反应，没有出现 "Device is Upgrading the Firmware"

CyrixIII

看起来这里用825的人不多啊
刚才google了一下，国内基本没啥有用的信息
在国外的2个blog里找到2条可能有用
一条是跟官网wiki里有提过的类似，就是说要在100M网络下刷新，不过官网只是说在linux下需要设置成100M，如下：

· If you are running Linux you can:
  · Set your interface to 100Mbps using sudo ethtool -s eth0 speed 100 autoneg off, install IE7 in Wine and use it to flash.
  · Later models (or some hardware combinations) may need sudo ethtool -s eth0 speed 100 duplex half autoneg off (e.g. B2, FW ver 2.05EU).

但是那个blog里说：

The actual problem is that the recovery mode doesn’t work over a gigabit LAN link.  (This is now noted in the OpenWRT wiki, but wasn’t back when I first was trying to install OpenWRT.)  If you stick to 100 Mbps or 10 Mbps, it works fine.  Some people have had luck with issuing a command on their host to force the interface to 100 Mbps.

另外一条是说不但要100M，并且是在Windows XP里刷新成功的

Note to people passing by. I had this problem too. I tried with all of the methods mentioned above and also with external 10/100 Ethernet adapters. My last resort was to borrow my girlfriend’s laptop running Windows XP. It worked right away. Maybe there’s more than one problem, but bite the bullet and try with a Windows box before you give up.

罗技专卖店

不是用的人少，而是你的问题人家没遇到过

CyrixIII

罗技专卖店 发表于 2012-2-20 13:37
不是用的人少，而是你的问题人家没遇到过

难道说其他都还用XP，100M LAN
晕

CyrixIII

搞定了，确实是在IE7+100M网卡下才能刷新