设为首页收藏本站

简体中文 繁體中文 English 日本語 Deutsch 한국 사람 بالعربية TÜRKÇE português คนไทย

切换到窄版

 找回密码
 立即注册

QQ登录

只需一步，快速开始

搜索
恩山无线论坛»论坛 › 无线设备硬件相关板块 › tenda腾达无线路由器以及腾达其它网络设备 › 腾达W311R RT3050 4M闪存16位16M双内存焊盘 改 32位32M ...
广告投放联系QQ68610888
1234567下一页
返回列表 发新帖
查看: 59123|回复: 102

腾达W311R RT3050 4M闪存16位16M双内存焊盘 改 32位32M内存已经上传U-BOOT编程器固...

 火.. [复制链接]
| 显示全部楼层 |阅读模式
本帖最后由 德国之声 于 2013-1-8 22:58 编辑

腾达W311R    RT3050  双焊盘 双内存  32M 32位  4M闪存

JTAG  备份闪存镜像    brjtag -backup:wholeflash /verbose
腾达W311R RT3050 4M闪存16位16M 双内存焊盘 改 32位32M内存刷好DD

编程器  JTAG   镜像文件



KH29LV320CBTC-70

编程器 固件  在 46楼 下载........谢谢大家支持..














腾达 W311R 原装机器的  UBOOT   4M  闪存 16位 16M 内存

U-Boot 1.1.3 (Feb 13 2009 - 10:05:04)

Board: Ralink APSoC DRAM:  16 MB
relocate_code Pointer at: 80fac000
flash_protect ON: from 0xBF000000 to 0xBF01FFAF
protect on 0
protect on 1
protect on 2
protect on 3
protect on 4
protect on 5
protect on 6
protect on 7
protect on 8
flash_protect ON: from 0xBF030000 to 0xBF03FFFF
protect on 10
*** Warning - bad CRC, using default environment

============================================
Ralink UBoot Version: 3.2
--------------------------------------------
ASIC 3052_MP2 (Port5<->None)
DRAM COMPONENT: 128Mbits
DRAM BUS: 16BIT
Total memory: 16 MBytes
Date:Feb 13 2009  Time:10:05:04
============================================
icache: sets:256, ways:4, linesz:32 ,total:32768
dcache: sets:128, ways:4, linesz:32 ,total:16384

##### The CPU freq = 384 MHZ ####

SDRAM bus set to 16 bit
SDRAM size =16 Mbytes

Please choose the operation:
   1: Load system code to SDRAM via TFTP.
   2: Load system code then write to Flash via TFTP.
   3: Boot system code via Flash (default).
   4: Entr boot command line interface.
   9: Load Boot Loader code then write to Flash via TFTP.
0

3: System Boot system code via Flash.
## Booting image at bf050000 ...
   Image Name:   linkn_16MB_2MB Kernel Image
   Created:      2009-02-23  18:43:36 UTC

System Control Status = 0x20440000
   Image Type:   MIPS Linux Kernel Image (lzma compressed)
   Data Size:    1657372 Bytes =  1.6 MB
   Load Address: 80000000
   Entry Point:  80263000
   Verifying Checksum ... OK
   Uncompressing Kernel Image ... OK
No initrd
## Transferring control to Linux (at address 80263000) ...
## Giving linux memsize in MB, 16

Starting kernel ...


LINUX started...

THIS IS ASIC
init started: BusyBox v1.12.1 (2009-02-24 02:38:40 CST)
starting pid 11, tty '': '/etc_ro/rcS'
mount: mounting none on /proc/bus/usb failed: No such file or directory
Welcome to
     _______  _______  ___     __  ____   _  _   ___
    |  ___  \|   __  ||   |   |__||    \ | || | /  /
    | |___| ||  |__| ||   |__  __ |     \| || |/  /
    |   _   /|   _   ||      ||  || |\     ||     \
    |__| \__\|__| |__||______||__||_| \____||_|\___\

                     =System Architecture Department=



Yes:

      ****** WeLoveLinux ******

Welcome to ...
httpd Reg gpio hook success .
starting pid 19, tty '/dev/ttyS1': '/bin/sh'


BusyBox v1.12.1 (2009-02-24 02:38:40 CST) built-in shell (ash)
Enter 'help' for a list of built-in commands.

# getIfLive: device eth2.1 not found.
Commit crc = 6c387a64
maclist:
WLan[00:B0:0C:25:C0:70]
Lan[00:B0:0C:25:C0:70]
Wan[00:B0:0C:25:C0:75]
getIfLive: device br0 not found.
Router ip address config success.
libupnp: using UDP SSDP_PORT = 1900
killall: udhcpd: no process killed
httpd listen ip = 192.168.0.1 port = 80
MfgThread start loop.
TendaLog -> ok rtn.
udhcpc (v1.12.1) started


我的恩山、我的无线 The best wifi forum is right here.
回复

使用道具 举报

 楼主| | 显示全部楼层
本帖最后由 德国之声 于 2012-4-5 15:21 编辑


腾达 W311R 原装机器的  UBOOT   4M  闪存 16位 16M 内存

直接无改 TTL 超级终端  刷DD。。。内存小了郁闷。。。

U-Boot 1.1.3 (Feb 13 2009 - 10:05:04)

Board: Ralink APSoC DRAM:  16 MB
relocate_code Pointer at: 80fac000
flash_protect ON: from 0xBF000000 to 0xBF01FFAF
protect on 0
protect on 1
protect on 2
protect on 3
protect on 4
protect on 5
protect on 6
protect on 7
protect on 8
flash_protect ON: from 0xBF030000 to 0xBF03FFFF
protect on 10
*** Warning - bad CRC, using default environment

============================================
Ralink UBoot Version: 3.2
--------------------------------------------
ASIC 3052_MP2 (Port5<->None)
DRAM COMPONENT: 128Mbits
DRAM BUS: 16BIT
Total memory: 16 MBytes
Date:Feb 13 2009  Time:10:05:04
============================================
icache: sets:256, ways:4, linesz:32 ,total:32768
dcache: sets:128, ways:4, linesz:32 ,total:16384

##### The CPU freq = 384 MHZ ####

SDRAM bus set to 16 bit
SDRAM size =16 Mbytes

Please choose the operation:
   1: Load system code to SDRAM via TFTP.
   2: Load system code then write to Flash via TFTP.
   3: Boot system code via Flash (default).
   4: Entr boot command line interface.
   9: Load Boot Loader code then write to Flash via TFTP.
0

3: System Boot system code via Flash.
## Booting image at bf050000 ...
   Image Name:   DD-WRT v24 Linux Kernel Image
   Created:      2009-10-10   9:36:32 UTC

System Control Status = 0x20440000
   Image Type:   MIPS Linux Kernel Image (lzma compressed)
   Data Size:    864826 Bytes = 844.6 kB
   Load Address: 80000000
   Entry Point:  8026d000
   Verifying Checksum ... OK
   Uncompressing Kernel Image ... OK
No initrd
## Transferring control to Linux (at address 8026d000) ...
## Giving linux memsize in MB, 16

Starting kernel ...


LINUX started...

THIS IS ASIC
Linux version 2.6.23.17 (root@dd-wrt) (gcc version 4.1.2) #968 Sat Oct 10 11:32:
30 CEST 2009

The CPU frequency set to 384 MHz
16M RAM Detected!
CPU revision is: 0001964c
Determined physical RAM map:
memory: 01000000 @ 00000000 (usable)
Built 1 zonelists in Zone order.  Total pages: 4064
Kernel command line: console=ttyS1,57600n8 root=/dev/mtdblock4 rootfstype=squash
fs noinitrd
Primary instruction cache 32kB, physically tagged, 4-way, linesize 32 bytes.
Primary data cache 16kB, 4-way, linesize 32 bytes.
Synthesized TLB refill handler (20 instructions).
Synthesized TLB load handler fastpath (32 instructions).
Synthesized TLB store handler fastpath (32 instructions).
Synthesized TLB modify handler fastpath (31 instructions).
Cache parity protection disabled
cause = 800008, status = 1100ff00
PID hash table entries: 64 (order: 6, 256 bytes)
calculating r4koff... 003a9800(3840000)
CPU frequency 384.00 MHz
Using 192.000 MHz high precision timer.
console [ttyS1] enabled
Dentry cache hash table entries: 2048 (order: 1, 8192 bytes)
Inode-cache hash table entries: 1024 (order: 0, 4096 bytes)
Memory: 13236k/16384k available (2159k kernel code, 3148k reserved, 320k data, 1
20k init, 0k highmem)
Mount-cache hash table entries: 512
NET: Registered protocol family 16
Generic PHY: Registered new driver
NET: Registered protocol family 2
Time: MIPS clocksource has been installed.
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
TCP established hash table entries: 512 (order: 0, 4096 bytes)
TCP bind hash table entries: 512 (order: -1, 2048 bytes)
TCP: Hash tables configured (established 512 bind 512)
TCP reno registered
Load RT2880 Timer Module(Wdg/Soft)
devfs: 2004-01-31 Richard Gooch (rgooch@atnf.csiro.au)
devfs: boot_options: 0x1
squashfs: version 3.0 (2006/03/15) Phillip Lougher
io scheduler noop registered
io scheduler deadline registered (default)
Ralink gpio driver initialized
Serial: 8250/16550 driver $Revision: 1.3 $ 2 ports, IRQ sharing disabled
serial8250: ttyS0 at I/O 0xb0000500 (irq = 37) is a 16550A
serial8250: ttyS1 at I/O 0xb0000c00 (irq = 12) is a 16550A
rt3052 access driver initialization.
PPP generic driver version 2.4.2
PPP Deflate Compression module registered
PPP BSD Compression module registered
MPPE/MPPC encryption/compression module registered
NET: Registered protocol family 24
PPPoL2TP kernel driver, V1.0
tun: Universal TUN/TAP device driver, 1.6
tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
ralink flash device: 0x1000000 at 0xbf000000
Ralink SoC physically mapped flash: Found 1 x16 devices at 0x0 in 16-bit bank
Amd/Fujitsu Extended Query Table at 0x0040
number of CFI chips: 1
cfi_cmdset_0002: Disabling erase-suspend-program due to code brokenness.

found squashfs at 124000
Creating 6 MTD partitions on "Ralink SoC physically mapped flash":
0x00000000-0x00030000 : "uboot"
0x00030000-0x00040000 : "uboot-config"
0x00040000-0x00050000 : "factory-defaults"
0x00050000-0x003f0000 : "linux"
0x00124000-0x003f0000 : "rootfs"
mtd: partition "rootfs" doesn't start on an erase block boundary -- force read-o
nly
0x003f0000-0x00400000 : "nvram"
u32 classifier
    Actions configured
Netfilter messages via NETLINK v0.30.
nf_conntrack version 0.5.0 (1024 buckets, 4096 max)
ctnetlink v0.93: registering with nfnetlink.
IPv4 over IPv4 tunneling driver
GRE over IPv4 tunneling driver
ip_tables: (C) 2000-2006 Netfilter Core Team
IPP2P v0.8.2 loading
ClusterIP Version 0.8 loaded successfully
TCP bic registered
TCP cubic registered
TCP westwood registered
TCP highspeed registered
TCP hybla registered
TCP htcp registered
TCP vegas registered
TCP scalable registered
NET: Registered protocol family 1
NET: Registered protocol family 17
Welcome to PF_RING 3.2.1
(C) 2004-06 L.Deri <deri@ntop.org>
NET: Registered protocol family 27
PF_RING: bucket length    128 bytes
PF_RING: ring slots       4096
PF_RING: sample rate      1 [1=no sampling]
PF_RING: capture TX       No [RX only]
PF_RING: transparent mode Yes
PF_RING initialized correctly.
PF_RING: registered /proc/net/pf_ring/
802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>
All bugs added by David S. Miller <davem@redhat.com>
GDMA1_MAC_ADRH -- : 0x00000000
GDMA1_MAC_ADRL -- : 0x00000000
Ralink APSoC Ethernet Driver Initilization. v2.00  256 rx/tx descriptors allocat
ed, mtu = 1500!
NAPI enable, weight = 0, Tx Ring = 256, Rx Ring = 256
GDMA1_MAC_ADRH -- : 0x0000000c
GDMA1_MAC_ADRL -- : 0x43305277
PROC INIT OK!
decode /dev/mtdblock4
VFS: Mounted root (squashfs filesystem) readonly.
Mounted devfs on /dev
Freeing unused kernel memory: 120k freed
starting Architecture code for rt2880
switch reg write offset=14, value=405555
switch reg write offset=50, value=2001
switch reg write offset=98, value=7f3f
switch reg write offset=e4, value=3f
switch reg write offset=40, value=1001
switch reg write offset=44, value=1001
switch reg write offset=48, value=1002
switch reg write offset=70, value=ffff506f
sh: ead: not found
wland: No such file or directory
SIOCGIFFLAGS: No such device
SIOCGIFFLAGS: No such device
SIOCGIFFLAGS: No such device
SIOCGIFFLAGS: No such device
SIOCGIFFLAGS: No such device
SIOCGIFFLAGS: No such device
SIOCGIFFLAGS: No such device
Apply:submit_button=[Management] service=[management] sleep_time=[0] action=[4]
nvram_commit(): end
ApplyTake:submit_button=[Management] service=[management] sleep_time=[0] action=
[4]
nvram_commit(): end
SIOCGIFFLAGS: No such device
SIOCGIFFLAGS: No such device
SIOCGIFFLAGS: No such device
SIOCGIFFLAGS: No such device
SIOCGIFFLAGS: No such device
SIOCGIFFLAGS: No such device
SIOCGIFFLAGS: No such device
vlan2: No such process
vlan2: No such process
bridge br0 is still up; can't delete it
device br0 already exists; can't create bridge with the same name
sh: ead: not found
lo: File exists
wland: No such file or directory
SIOCGIFFLAGS: No such device
SIOCGIFFLAGS: No such device
SIOCGIFFLAGS: No such device
SIOCGIFFLAGS: No such device
SIOCGIFFLAGS: No such device
SIOCGIFFLAGS: No such device
SIOCGIFFLAGS: No such device
ApplyTake:submit_button=[Management] service=[management] sleep_time=[0] action=
[4]
nvram_commit(): end
SIOCGIFFLAGS: No such device
SIOCGIFFLAGS: No such device
SIOCGIFFLAGS: No such device
SIOCGIFFLAGS: No such device
SIOCGIFFLAGS: No such device
SIOCGIFFLAGS: No such device
SIOCGIFFLAGS: No such device
vlan2: No such process
vlan2: No such process
bridge br0 is still up; can't delete it
device br0 already exists; can't create bridge with the same name
sh: ead: not found
lo: File exists
wland: No such file or directory
SIOCGIFFLAGS: No such device
SIOCGIFFLAGS: No such device
SIOCGIFFLAGS: No such device
SIOCGIFFLAGS: No such device
SIOCGIFFLAGS: No such device
SIOCGIFFLAGS: No such device
SIOCGIFFLAGS: No such device
Apply:submit_button=[Management] service=[management] sleep_time=[0] action=[4]
nvram_commit(): end
connect: Network is unreachable
connect: Network is unreachable
connect: Network is unreachable
gethostbyname: Network is unreachable
[ 0] SSID[无线                            ] BSSID[5c:63:bf:eb:96:8e] channel[ 1]
rssi[0] noise[-95] beacon[0] cap[11] dtim[0] rate[300]
[ 1] SSID[ WRT54G                         ] BSSID[00:18:39:f4:17:43] channel[ 9]
rssi[-55] noise[-95] beacon[0] cap[11] dtim[0] rate[12]
我的恩山、我的无线 The best wifi forum is right here.
回复

使用道具 举报

 楼主| | 显示全部楼层
已经刷好DD。。。。。{:soso_e102:}{:soso_e102:}
我的恩山、我的无线 The best wifi forum is right here.
回复

使用道具 举报

| 显示全部楼层
怎么刷的？求固件和方法
我的恩山、我的无线 The best wifi forum is right here.
回复

使用道具 举报

 楼主| | 显示全部楼层
本帖最后由 德国之声 于 2012-4-5 15:25 编辑


腾达 W311R 原装机器的  UBOOT   4M  闪存 16位 16M 内存
  硬件改成 双内存颗粒 32位 32M内存 两颗16位16M内存
  TTL  超级终端 刷UBOOT  

U-Boot 1.1.3 (Mar 28 2011 - 20:25:35)

Board: Ralink APSoC DRAM:  32 MB
relocate_code Pointer at: 81fb0000
config usb....
flash_protect ON: from 0xBF000000 to 0xBF01E587
flash_protect ON: from 0xBF030000 to 0xBF030FFF
*** Warning - bad CRC, using default environment

============================================
Ralink UBoot Version: 3.4.0.0
--------------------------------------------
ASIC 3052_MP2 (Port5<->None)
DRAM component: 128 Mbits SDR
DRAM bus: 32 bit
Total memory: 32 MBytes
Flash component: NOR Flash
Date:Mar 28 2011  Time:20:25:35
============================================
icache: sets:256, ways:4, linesz:32 ,total:32768
dcache: sets:128, ways:4, linesz:32 ,total:16384

##### The CPU freq = 384 MHZ ####

SDRAM bus set to 32 bit
SDRAM size =32 Mbytes

Please choose the operation:
   1: Load system code to SDRAM via TFTP.
   2: Load system code then write to Flash via TFTP.
   3: Boot system code via Flash (default).
   4: Entr boot command line interface.
   7: Load Boot Loader code then write to Flash via Serial.
   8: Load Boot Loader code to SDRAM via TFTP.
   9: Load Boot Loader code then write to Flash via TFTP.
0

3: System Boot system code via Flash.
## Booting image at bf050000 ...
   Image Name:   DD-WRT v24 Linux Kernel Image
   Created:      2009-10-10   9:36:32 UTC
   Image Type:   MIPS Linux Kernel Image (lzma compressed)
   Data Size:    864826 Bytes = 844.6 kB
   Load Address: 80000000
   Entry Point:  8026d000
   Verifying Checksum ... OK
   Uncompressing Kernel Image ... OK
No initrd
## Transferring control to Linux (at address 8026d000) ...
## Giving linux memsize in MB, 32

Starting kernel ...


LINUX started...

THIS IS ASIC
Linux version 2.6.23.17 (root@dd-wrt) (gcc version 4.1.2) #968 Sat Oct 10 11:32:
30 CEST 2009

The CPU frequency set to 384 MHz
32M RAM Detected!
CPU revision is: 0001964c
Determined physical RAM map:
memory: 02000000 @ 00000000 (usable)
Built 1 zonelists in Zone order.  Total pages: 8128
Kernel command line: console=ttyS1,57600n8 root=/dev/mtdblock4 rootfstype=squash
fs noinitrd
Primary instruction cache 32kB, physically tagged, 4-way, linesize 32 bytes.
Primary data cache 16kB, 4-way, linesize 32 bytes.
Synthesized TLB refill handler (20 instructions).
Synthesized TLB load handler fastpath (32 instructions).
Synthesized TLB store handler fastpath (32 instructions).
Synthesized TLB modify handler fastpath (31 instructions).
Cache parity protection disabled
cause = 90800014, status = 1100ff00
PID hash table entries: 128 (order: 7, 512 bytes)
calculating r4koff... 003a9800(3840000)
CPU frequency 384.00 MHz
Using 192.000 MHz high precision timer.
console [ttyS1] enabled
Dentry cache hash table entries: 4096 (order: 2, 16384 bytes)
Inode-cache hash table entries: 2048 (order: 1, 8192 bytes)
Memory: 29480k/32768k available (2159k kernel code, 3288k reserved, 320k data, 1
20k init, 0k highmem)
Mount-cache hash table entries: 512
NET: Registered protocol family 16
Generic PHY: Registered new driver
NET: Registered protocol family 2
Time: MIPS clocksource has been installed.
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
TCP established hash table entries: 1024 (order: 1, 8192 bytes)
TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
TCP: Hash tables configured (established 1024 bind 1024)
TCP reno registered
Load RT2880 Timer Module(Wdg/Soft)
devfs: 2004-01-31 Richard Gooch (rgooch@atnf.csiro.au)
devfs: boot_options: 0x1
squashfs: version 3.0 (2006/03/15) Phillip Lougher
io scheduler noop registered
io scheduler deadline registered (default)
Ralink gpio driver initialized
Serial: 8250/16550 driver $Revision: 1.3 $ 2 ports, IRQ sharing disabled
serial8250: ttyS0 at I/O 0xb0000500 (irq = 37) is a 16550A
serial8250: ttyS1 at I/O 0xb0000c00 (irq = 12) is a 16550A
rt3052 access driver initialization.
PPP generic driver version 2.4.2
PPP Deflate Compression module registered
PPP BSD Compression module registered
MPPE/MPPC encryption/compression module registered
NET: Registered protocol family 24
PPPoL2TP kernel driver, V1.0
tun: Universal TUN/TAP device driver, 1.6
tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
ralink flash device: 0x1000000 at 0xbf000000
Ralink SoC physically mapped flash: Found 1 x16 devices at 0x0 in 16-bit bank
Amd/Fujitsu Extended Query Table at 0x0040
number of CFI chips: 1
cfi_cmdset_0002: Disabling erase-suspend-program due to code brokenness.

found squashfs at 124000
Creating 6 MTD partitions on "Ralink SoC physically mapped flash":
0x00000000-0x00030000 : "uboot"
0x00030000-0x00040000 : "uboot-config"
0x00040000-0x00050000 : "factory-defaults"
0x00050000-0x003f0000 : "linux"
0x00124000-0x003f0000 : "rootfs"
mtd: partition "rootfs" doesn't start on an erase block boundary -- force read-o
nly
0x003f0000-0x00400000 : "nvram"
u32 classifier
    Actions configured
Netfilter messages via NETLINK v0.30.
nf_conntrack version 0.5.0 (1024 buckets, 4096 max)
ctnetlink v0.93: registering with nfnetlink.
IPv4 over IPv4 tunneling driver
GRE over IPv4 tunneling driver
ip_tables: (C) 2000-2006 Netfilter Core Team
IPP2P v0.8.2 loading
ClusterIP Version 0.8 loaded successfully
TCP bic registered
TCP cubic registered
TCP westwood registered
TCP highspeed registered
TCP hybla registered
TCP htcp registered
TCP vegas registered
TCP scalable registered
NET: Registered protocol family 1
NET: Registered protocol family 17
Welcome to PF_RING 3.2.1
(C) 2004-06 L.Deri <deri@ntop.org>
NET: Registered protocol family 27
PF_RING: bucket length    128 bytes
PF_RING: ring slots       4096
PF_RING: sample rate      1 [1=no sampling]
PF_RING: capture TX       No [RX only]
PF_RING: transparent mode Yes
PF_RING initialized correctly.
PF_RING: registered /proc/net/pf_ring/
802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>
All bugs added by David S. Miller <davem@redhat.com>
GDMA1_MAC_ADRH -- : 0x00000000
GDMA1_MAC_ADRL -- : 0x00000000
Ralink APSoC Ethernet Driver Initilization. v2.00  256 rx/tx descriptors allocat
ed, mtu = 1500!
NAPI enable, weight = 0, Tx Ring = 256, Rx Ring = 256
GDMA1_MAC_ADRH -- : 0x0000000c
GDMA1_MAC_ADRL -- : 0x43305277
PROC INIT OK!
decode /dev/mtdblock4
VFS: Mounted root (squashfs filesystem) readonly.
Mounted devfs on /dev
Freeing unused kernel memory: 120k freed
starting Architecture code for rt2880
switch reg write offset=14, value=405555
switch reg write offset=50, value=2001
switch reg write offset=98, value=7f3f
switch reg write offset=e4, value=3f
switch reg write offset=40, value=1001
switch reg write offset=44, value=1001
switch reg write offset=48, value=1002
switch reg write offset=70, value=ffff506f
sh: ead: not found
wland: No such file or directory
SIOCGIFFLAGS: No such device
SIOCGIFFLAGS: No such device
SIOCGIFFLAGS: No such device
SIOCGIFFLAGS: No such device
SIOCGIFFLAGS: No such device
SIOCGIFFLAGS: No such device
SIOCGIFFLAGS: No such device
我的恩山、我的无线 The best wifi forum is right here.
回复

使用道具 举报

 楼主| | 显示全部楼层
本帖最后由 德国之声 于 2012-4-5 14:57 编辑

腾达 W311R 4M 16M 刷机 [

闪存 4M   内存  由原来的 16位 16M内存  改装成现在的32位 32M内存

性能大大增强。。。

完美运行DD。。。。
我的恩山、我的无线 The best wifi forum is right here.
回复

使用道具 举报

 楼主| | 显示全部楼层
本帖最后由 德国之声 于 2012-4-5 15:09 编辑

刷回原厂固件  H2_V3.2.5d.bin

U-Boot 1.1.3 (Mar 28 2011 - 20:25:35)

Board: Ralink APSoC DRAM:  32 MB
relocate_code Pointer at: 81fb0000
config usb....
flash_protect ON: from 0xBF000000 to 0xBF01E587
flash_protect ON: from 0xBF030000 to 0xBF030FFF
*** Warning - bad CRC, using default environment

============================================
Ralink UBoot Version: 3.4.0.0
--------------------------------------------
ASIC 3052_MP2 (Port5<->None)
DRAM component: 128 Mbits SDR
DRAM bus: 32 bit
Total memory: 32 MBytes
Flash component: NOR Flash
Date:Mar 28 2011  Time:20:25:35
============================================
icache: sets:256, ways:4, linesz:32 ,total:32768
dcache: sets:128, ways:4, linesz:32 ,total:16384

##### The CPU freq = 384 MHZ ####

SDRAM bus set to 32 bit
SDRAM size =32 Mbytes

Please choose the operation:
   1: Load system code to SDRAM via TFTP.
   2: Load system code then write to Flash via TFTP.
   3: Boot system code via Flash (default).
   4: Entr boot command line interface.
   7: Load Boot Loader code then write to Flash via Serial.
   8: Load Boot Loader code to SDRAM via TFTP.
   9: Load Boot Loader code then write to Flash via TFTP.
2
You choosed 2

0


2: System Load Linux Kernel then write to Flash via TFTP.
Warning!! Erase Linux in Flash then burn new one. Are you sure?(Y/N)
Please Input new ones /or Ctrl-C to discard
        Input device IP (192.168.1.100) ==:192.168.1.1
        Input server IP (192.168.1.2) ==:192.168.1.2
        Input Linux Kernel filename () ==:H2_V3.2.5d.bin

netboot_common, argc= 3

NetTxPacket = 0x81FE6800

KSEG1ADDR(NetTxPacket) = 0xA1FE6800

NetLoop,call eth_halt !

NetLoop,call eth_init !
Trying Eth0 (10/100-M)

Waitting for RX_DMA_BUSY status Start... done

Header Payload scatter function is Disable !!

ETH_STATE_ACTIVE!!
Using Eth0 (10/100-M) device
TFTP from server 192.168.1.2; our IP address is 192.168.1.1
Filename 'H2_V3.2.5d.bin'.

TIMEOUT_COUNT=10,Load address: 0x80100000
Loading: *
ArpTimeoutCheck
Got ARP REPLY, set server/gtwy eth addr (00:b0:5c:40:03:32)
Got it
#################################################################
         #################################################################
         #################################################################
         #################################################################
         #################################################################
         #################################################################
         ######################################################
done
Bytes transferred = 2270488 (22a518 hex)
NetBootFileXferSize= 0022a518
Erase linux kernel block !!
From 0xBF050000 To 0xBF27FFFF

b_end =BF3FFFFF
Erase Flash from 0xbf050000 to 0xbf27ffff in Bank # 1

erase sector  = 12
sect = 12,s_last = 46,erase poll = 1184929

erase sector  = 13
*sect = 13,s_last = 46,erase poll = 1176815

erase sector  = 14
sect = 14,s_last = 46,erase poll = 1194450

erase sector  = 15
*sect = 15,s_last = 46,erase poll = 1184477

erase sector  = 16
sect = 16,s_last = 46,erase poll = 1199194

erase sector  = 17
*sect = 17,s_last = 46,erase poll = 1160512

erase sector  = 18
sect = 18,s_last = 46,erase poll = 1211485

erase sector  = 19
*sect = 19,s_last = 46,erase poll = 1171428

erase sector  = 20
*sect = 20,s_last = 46,erase poll = 1185403

erase sector  = 21
sect = 21,s_last = 46,erase poll = 1172056

erase sector  = 22
*sect = 22,s_last = 46,erase poll = 1233933

erase sector  = 23
sect = 23,s_last = 46,erase poll = 1188156

erase sector  = 24
*sect = 24,s_last = 46,erase poll = 1198662

erase sector  = 25
sect = 25,s_last = 46,erase poll = 1173653

erase sector  = 26
*sect = 26,s_last = 46,erase poll = 1182704

erase sector  = 27
*sect = 27,s_last = 46,erase poll = 1171629

erase sector  = 28
sect = 28,s_last = 46,erase poll = 1197471

erase sector  = 29
*sect = 29,s_last = 46,erase poll = 1171103

erase sector  = 30
sect = 30,s_last = 46,erase poll = 1211098

erase sector  = 31
*sect = 31,s_last = 46,erase poll = 1160384

erase sector  = 32
sect = 32,s_last = 46,erase poll = 1193694

erase sector  = 33
*sect = 33,s_last = 46,erase poll = 1188153

erase sector  = 34
*sect = 34,s_last = 46,erase poll = 1184012

erase sector  = 35
sect = 35,s_last = 46,erase poll = 1174723

erase sector  = 36
*sect = 36,s_last = 46,erase poll = 1235521

erase sector  = 37
sect = 37,s_last = 46,erase poll = 1194192

erase sector  = 38
*sect = 38,s_last = 46,erase poll = 1204718

erase sector  = 39
sect = 39,s_last = 46,erase poll = 1188973

erase sector  = 40
*sect = 40,s_last = 46,erase poll = 1210328

erase sector  = 41
*sect = 41,s_last = 46,erase poll = 1171679

erase sector  = 42
sect = 42,s_last = 46,erase poll = 1187429

erase sector  = 43
*sect = 43,s_last = 46,erase poll = 1160697

erase sector  = 44
sect = 44,s_last = 46,erase poll = 1182090

erase sector  = 45
*sect = 45,s_last = 46,erase poll = 1189012

erase sector  = 46
sect = 46,s_last = 46,erase poll = 1202402
done
Erased 35 sectors

Copy linux image[2270488 byte] to Flash[0xBF050000]....
Copy to Flash...
Copy 2270488 byte to Flash...
addr = 0xBF0A1CDA ,cnt=1935422
addr = 0xBF0F39EE ,cnt=1600298
addr = 0xBF1456D6 ,cnt=1265218
addr = 0xBF1973C2 ,cnt=930134
addr = 0xBF1E908C ,cnt=595084
addr = 0xBF23AD7A ,cnt=259998 done
## Booting image at bf050000 ...
   Image Name:   linkn Kernel Image
   Created:      2009-02-24  11:08:38 UTC
   Image Type:   MIPS Linux Kernel Image (lzma compressed)
   Data Size:    2270424 Bytes =  2.2 MB
   Load Address: 80000000
   Entry Point:  803cd000
   Verifying Checksum ... OK
   Uncompressing Kernel Image ... OK
No initrd
## Transferring control to Linux (at address 803cd000) ...
## Giving linux memsize in MB, 32

Starting kernel ...


我的恩山、我的无线 The best wifi forum is right here.
回复

使用道具 举报

ha***
| 显示全部楼层
本帖最后由 hanhg 于 2013-9-1 02:30 编辑

手上有个311R，买来就没有怎么用，一直闲置！
我的恩山、我的无线 The best wifi forum is right here.
回复

使用道具 举报

蓝***
| 显示全部楼层
英语不知道是啥子，但是，还要恭喜！
我的恩山、我的无线 The best wifi forum is right here.
回复

使用道具 举报

ant***
| 显示全部楼层
最好能给个9楼用的……带usb…谢啦
我的恩山、我的无线 The best wifi forum is right here.
回复

使用道具 举报

ant***
| 显示全部楼层

RE: 腾达 W311R RT3050 4M 16M 双内存焊盘 刷机

德国之声 发表于 2012-3-15 16:13
U-Boot 1.1.3 (Mar 28 2011 - 20:25:35)

Board: Ralink APSoC DRAM:  32 MB

楼主能把这份UBOOT给我个吗？谢谢了
1028234385@qq.com
我的恩山、我的无线 The best wifi forum is right here.
回复

使用道具 举报

 楼主| | 显示全部楼层
本帖最后由 德国之声 于 2012-4-5 15:35 编辑

上传  固件  教程   


本帖子中包含更多资源

您需要 登录 才可以下载或查看，没有账号？立即注册

×
我的恩山、我的无线 The best wifi forum is right here.
回复

使用道具 举报

 楼主| | 显示全部楼层
本帖最后由 德国之声 于 2012-4-5 15:02 编辑

刷 UBOOT  教程    

   1: Load system code to SDRAM via TFTP.
   2: Load system code then write to Flash via TFTP.
   3: Boot system code via Flash (default).
   4: Entr boot command line interface.
   9: Load Boot Loader code then write to Flash via TFTP.

1：系统代码，即通过功能。

2：负载系统的代码写闪存通过档案。

3：系统的启动代码通过闪光（默认）。

4项启动命令行接口。

9：负载启动加载器代码写入闪存通过档案。


我的恩山、我的无线 The best wifi forum is right here.
回复

使用道具 举报

 楼主| | 显示全部楼层
本帖最后由 德国之声 于 2012-4-5 15:54 编辑

腾达 W311R 原装机器的  UBOOT   4M  闪存 16位 16M 内存
改  32位 32M内存  刷  UBOOT  教程
U-Boot 1.1.3 (Feb 13 2009 - 10:05:04)

Board: Ralink APSoC DRAM:  16 MB
relocate_code Pointer at: 80fac000
flash_protect ON: from 0xBF000000 to 0xBF01FFAF
protect on 0
protect on 1
protect on 2
protect on 3
protect on 4
protect on 5
protect on 6
protect on 7
protect on 8
flash_protect ON: from 0xBF030000 to 0xBF03FFFF
protect on 10
*** Warning - bad CRC, using default environment

============================================
Ralink UBoot Version: 3.2
--------------------------------------------
ASIC 3052_MP2 (Port5<->None)
DRAM COMPONENT: 128Mbits
DRAM BUS: 16BIT
Total memory: 16 MBytes
Date:Feb 13 2009  Time:10:05:04
============================================
icache: sets:256, ways:4, linesz:32 ,total:32768
dcache: sets:128, ways:4, linesz:32 ,total:16384

##### The CPU freq = 384 MHZ ####

SDRAM bus set to 16 bit
SDRAM size =16 Mbytes

Please choose the operation:
   1: Load system code to SDRAM via TFTP.
   2: Load system code then write to Flash via TFTP.
   3: Boot system code via Flash (default).
   4: Entr boot command line interface.
   9: Load Boot Loader code then write to Flash via TFTP.



我的恩山、我的无线 The best wifi forum is right here.
回复

使用道具 举报

 楼主| | 显示全部楼层
硬件改装好后

先改 有线网卡 IP地址为 192.168.1.2  连接上无线路由

接好TTL数据线 开启电脑  超级终端  57600  8  N  1

打开TENDA TFTP  选择要上传的UBOOT的本地电脑地址

看到TTL超级终端有显示 迅速 按数字键  9  

接下来   提示是否要升级  Boot Loader code   按 Y  选择  是   回车

然后  输入  无线路由的IP地址  比如  192.168.1.1  回车

然后  输入  TFTP 上传固件服务器IP地址 比如 192.168.1.2  回车

最后  输入   TFTP 要上传的固件 名字  比如  uboot[1].bin  回车

TFTP系统会自动刷新固件  等几分钟   OK。。。
我的恩山、我的无线 The best wifi forum is right here.
回复

使用道具 举报

1234567下一页
返回列表 发新帖
高级模式
B Color Image Link Quote Code Smilies
您需要登录后才可以回帖 登录 | 立即注册

本版积分规则

关闭

欢迎大家光临恩山无线论坛上一条 /1 下一条

有疑问请添加管理员QQ86788181|手机版|小黑屋|Archiver|恩山无线论坛(常州市恩山计算机开发有限公司版权所有) ( 苏ICP备05084872号 )

GMT+8, 2024-4-29 02:11

Powered by Discuz! X3.5

© 2001-2024 Discuz! Team.

| 江苏省互联网有害信息举报中心 举报信箱：js12377 | @jischina.com.cn 举报电话：025-88802724 本站不良内容举报信箱：68610888@qq.com 举报电话：0519-86695797

快速回复 返回顶部 返回列表