找回密码
 立即注册

QQ登录

只需一步,快速开始

搜索
广告投放联系QQ68610888
查看: 5764|回复: 7

网件R6900/R7000还原备份的CFE后变砖,修复记录见3楼

[复制链接]
发表于 2022-1-8 11:49 | 显示全部楼层 |阅读模式
本帖最后由 wz161996 于 2022-1-8 12:53 编辑

先说下背景:
之前为了体验AImesh,刷了1.3.0.7的CFE,之后可以成功的刷ac68u的官方固件。后来换了tplink的易展路由,这个就闲置了。最近没事,就想还原到官方的固件,降级到384固件后开启ssh,直接刷入之前备份的CFE,完成后reboot重启路由。

现状:
进不去系统,直接拆机,接TTL,尝试中断启动后,TFTP方式刷入固件,上传成功后,一直卡在reading,包括ac68u固件,网件官方固件,TT-WRT固件等等。。手动重启,30-30-30,各种方式都尝试了,均无效。

TTL不中断,日志输出到最后,一直打印以下内容:
[bwdpi check] starting...
Couldn't get the enabled rules of Parental-control correctly!
rc: ==> binding interface(vlan1,eth1,eth2,wds0.*,wds1.*,wds2.*) for lldpd
RAST 18: ROAMAST Start...
wanduck: delay 4 seconds before the first detect...
[312 watchdog:btn_check +19] button RESET pressed
[312 watchdog:btn_check +19] button RESET pressed
[312 watchdog:btn_check +19] button RESET pressed
[312 watchdog:btn_check +19] button RESET pressed


修复前的完整日志:
  1.   Digital core power voltage set to 1.0V
  2. Decompressing...done
  3. Digital core power voltage set to 1.0V

  4. SHMOO VER 1.13

  5. PKID07DC06011801080000000000001A103F01000000

  6. S300001D7
  7. 00001360


  8. RDLYW0 00000004

  9. RDENW0 00000035

  10. RDQSW0

  11.     0000000000111111111122222222223333333333444444444455555555556666
  12.     0123456789012345678901234567890123456789012345678901234567890123
  13. 00 --++++++++++++++++++++++++++X++++++++++++++++++++++++++---------
  14. 01 --------+++++++++++++++++++++++++X++++++++++++++++++++++++------
  15. 02 -----+++++++++++++++++++++++++X++++++++++++++++++++++++---------
  16. 03 ----+++++++++++++++++++++++++X++++++++++++++++++++++++----------
  17. 04 --++++++++++++++++++++++++X++++++++++++++++++++++++-------------
  18. 05 ------++++++++++++++++++++++++++X+++++++++++++++++++++++++------
  19. 06 --++++++++++++++++++++++++X++++++++++++++++++++++++-------------
  20. 07 -------++++++++++++++++++++++++++X++++++++++++++++++++++++++----
  21. 08 ---++++++++++++++++++++++++X+++++++++++++++++++++++-------------
  22. 09 ---------+++++++++++++++++++++++++X++++++++++++++++++++++++-----
  23. 10 ----++++++++++++++++++++++++X++++++++++++++++++++++++-----------
  24. 11 -----------++++++++++++++++++++++++X++++++++++++++++++++++++----
  25. 12 ---++++++++++++++++++++++++X++++++++++++++++++++++++------------
  26. 13 ------------++++++++++++++++++++++++X+++++++++++++++++++++++----
  27. 14 ------++++++++++++++++++++++++X++++++++++++++++++++++++---------
  28. 15 -----------+++++++++++++++++++++++++X++++++++++++++++++++++++---


  29. P   W0

  30.     0000000000111111111122222222223333333333444444444455555555556666
  31.     0123456789012345678901234567890123456789012345678901234567890123
  32. 00 --++++++++++++++++++++++++++X++++++++++++++++++++++++++---------
  33. 01 --------++++++++++++++++++++++++X++++++++++++++++++++++++-------
  34. 02 -----+++++++++++++++++++++++++X+++++++++++++++++++++++++--------
  35. 03 ----++++++++++++++++++++++++++X+++++++++++++++++++++++++--------
  36. 04 -+-+++++++++++++++++++++++++X++++++++++++++++++++++++-----------
  37. 05 -----++++++++++++++++++++++++++X+++++++++++++++++++++++++-------
  38. 06 --+++++++++++++++++++++++++X+++++++++++++++++++++++++-----------
  39. 07 --------++++++++++++++++++++++++++X+++++++++++++++++++++++++----
  40. 08 --++++++++++++++++++++++++X++++++++++++++++++++++++-------------
  41. 09 --------+++++++++++++++++++++++++X+++++++++++++++++++++++++-----
  42. 10 --+++++++++++++++++++++++++X+++++++++++++++++++++++++-----------
  43. 11 ----------+++++++++++++++++++++++++X++++++++++++++++++++++++----
  44. 12 -++++++++++++++++++++++++++X+++++++++++++++++++++++++-----------
  45. 13 ----------+++++++++++++++++++++++++X++++++++++++++++++++++++----
  46. 14 -----+++++++++++++++++++++++++X++++++++++++++++++++++++---------
  47. 15 ----------+++++++++++++++++++++++++X+++++++++++++++++++++++++---


  48. N   W0

  49.     0000000000111111111122222222223333333333444444444455555555556666
  50.     0123456789012345678901234567890123456789012345678901234567890123
  51. 00 -+++++++++++++++++++++++++++X++++++++++++++++++++++++++---------
  52. 01 -------+++++++++++++++++++++++++X+++++++++++++++++++++++++------
  53. 02 ----+++++++++++++++++++++++++X+++++++++++++++++++++++++---------
  54. 03 ---+++++++++++++++++++++++++X+++++++++++++++++++++++++----------
  55. 04 --++++++++++++++++++++++++X++++++++++++++++++++++++-------------
  56. 05 -----++++++++++++++++++++++++++X+++++++++++++++++++++++++-------
  57. 06 --++++++++++++++++++++++++X++++++++++++++++++++++++-------------
  58. 07 ------+++++++++++++++++++++++++++X+++++++++++++++++++++++++++---
  59. 08 ---+++++++++++++++++++++++++X+++++++++++++++++++++++++----------
  60. 09 ---------+++++++++++++++++++++++++++X+++++++++++++++++++++++++--
  61. 10 ---++++++++++++++++++++++++++X+++++++++++++++++++++++++---------
  62. 11 -----------+++++++++++++++++++++++++X++++++++++++++++++++++++---
  63. 12 ---+++++++++++++++++++++++++X+++++++++++++++++++++++++----------
  64. 13 -----------+++++++++++++++++++++++++X++++++++++++++++++++++++---
  65. 14 ------+++++++++++++++++++++++++X+++++++++++++++++++++++++-------
  66. 15 -----------++++++++++++++++++++++++++X+++++++++++++++++++++++++-


  67. WRDQW0

  68.     0000000000111111111122222222223333333333444444444455555555556666
  69.     0123456789012345678901234567890123456789012345678901234567890123
  70. 00 +++++++++++++++++++++++X+++++++++++++++++++++++------++++++++++-
  71. 01 ++++++++++++++++++++++++X++++++++++++++++++++++++-------+++++++-
  72. 02 ++++++++++++++++++++++++X+++++++++++++++++++++++------+++++++++-
  73. 03 ++++++++++++++++++++++++X+++++++++++++++++++++++------+++++++++-
  74. 04 +++++++++++++++++++++X++++++++++++++++++++----------+++++++++++-
  75. 05 +++++++++++++++++++++++X+++++++++++++++++++++++------++++++++++-
  76. 06 ++++++++++++++++++++++X+++++++++++++++++++++---------++++++++++-
  77. 07 ++++++++++++++++++++++++X++++++++++++++++++++++++------++++++++-
  78. 08 ++++++++++++++++++++++X++++++++++++++++++++++--------++++++++++-
  79. 09 -++++++++++++++++++++++++X+++++++++++++++++++++++----------++++-
  80. 10 +++++++++++++++++++++++X+++++++++++++++++++++++-------+++++++++-
  81. 11 -++++++++++++++++++++++++X+++++++++++++++++++++++-----------+++-
  82. 12 +++++++++++++++++++++++X++++++++++++++++++++++------+++++++++++-
  83. 13 -++++++++++++++++++++++++X+++++++++++++++++++++++-----------+++-
  84. 14 ++++++++++++++++++++++++X+++++++++++++++++++++++---------++++++-
  85. 15 -++++++++++++++++++++++++X+++++++++++++++++++++++----------++++-


  86. WRDMW0 00000023
  87. WRDMW0 00000024


  88. ADDR

  89.     0000000000111111111122222222223333333333444444444455555555556666
  90.     0123456789012345678901234567890123456789012345678901234567890123
  91. 00 +++++++++++++++++++S+++++++++++X++++++++++++++++++++++++++++++++

  92. Decompressing...done


  93. CFE for Foxconn Router R7000 version: v1.0.22
  94. Build Date: Wed Mar 19 11:14:20 CST 2014
  95. Init Arena
  96. Init Devs.
  97. Boot up from NAND flash...
  98. Bootcode Boot partition size = 524288(0x80000)
  99. DDR Clock: 800 MHz
  100. Info: DDR frequency set from clkfreq=1000,*800*
  101. et0: Broadcom BCM47XX 10/100/1000 Mbps Ethernet Controller 6.37.15.1 (r407936)
  102. et1: Broadcom BCM47XX 10/100/1000 Mbps Ethernet Controller 6.37.15.1 (r407936)
  103. CPU type 0x0: 1000MHz
  104. Tot mem: 262144 KBytes

  105. Device eth0:  hwaddr 00-46-BC-8D-5E-71, ipaddr 192.168.1.1, mask 255.255.255.0
  106.         gateway not set, nameserver not set
  107. Checking crc...Loader:raw Filesys:raw Dev:nflash0.os File: Options:(null)
  108. Loading: .... 4068064 bytes read
  109. Entry at 0x00008000
  110. Closing network.
  111. Starting program at 0x00008000
  112. console [ttyS0] enabled, bootconsole disabled
  113. serial8250.0: ttyS1 at MMIO 0x18000400 (irq = 117) is a 16550
  114. brd: module loaded
  115. loop: module loaded
  116. pflash: found no supported devices
  117. bcmsflash: found no supported devices
  118. Boot partition size = 524288(0x80000)
  119. lookup_nflash_rootfs_offset: offset = 0x200000
  120. nflash: squash filesystem with lzma found at block 28
  121. Creating 4 MTD partitions on "nflash":
  122. 0x000000000000-0x000000080000 : "boot"
  123. 0x000000080000-0x000000200000 : "nvram"
  124. 0x000000200000-0x000004000000 : "linux"
  125. 0x00000039fb10-0x000004000000 : "rootfs"
  126. PPP generic driver version 2.4.2
  127. PPP MPPE Compression module registered
  128. NET: Registered protocol family 24
  129. PPTP driver version 0.8.5
  130. Mirror/redirect action on
  131. u32 classifier
  132.     Performance counters on
  133.     Actions configured
  134. Netfilter messages via NETLINK v0.30.
  135. nf_conntrack version 0.5.0 (3991 buckets, 15964 max)
  136. ctnetlink v0.93: registering with nfnetlink.
  137. xt_time: kernel timezone is -0000
  138. ip_tables: (C) 2000-2006 Netfilter Core Team
  139. TCP cubic registered
  140. NET: Registered protocol family 10
  141. ip6_tables: (C) 2000-2006 Netfilter Core Team
  142. NET: Registered protocol family 17
  143. L2TP core driver, V2.0
  144. PPPoL2TP kernel driver, V2.0
  145. 802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>
  146. All bugs added by David S. Miller <davem@redhat.com>
  147. Registering the dns_resolver key type
  148. Northstar brcmnand NAND Flash Controller driver, Version 0.1 (c) Broadcom Inc. 2012
  149. NAND device: Manufacturer ID: 0x01, Chip ID: 0xf1 (AMD NAND 128MiB 3,3V 8-bit)
  150. Spare area=64 eccbytes 56, ecc bytes located at:
  151. 2 3 4 5 6 7 8 9 10 11 12 13 14 15 18 19 20 21 22 23 24 25 26 27 28 29 30 31 34 35 36 37 38 39 40 41 42 43 44 45 46 47 50 51 52 53 54 55 56 57 58 59 60 61 62 63
  152. Available 7 bytes at (off,len):
  153. (1,1) (16,2) (32,2) (48,2) (0,0) (0,0) (0,0) (0,0)
  154. Scanning device for bad blocks
  155. Options: NO_AUTOINCR,NO_READRDY,BBT_SCAN2NDPAGE,
  156. Creating 2 MTD partitions on "brcmnand":
  157. 0x000004000000-0x000007ec0000 : "brcmnand"
  158. 0x000007ec0000-0x000008000000 : "asus"
  159. VFS: Mounted root (squashfs filesystem) readonly on device 31:3.
  160. devtmpfs: mounted
  161. Freeing init memory: 212K
  162. init_main start

  163. 1: set_action 0


  164. Hit ENTER for console...

  165. firmware version: 384.12_0
  166. [1 preinit:init_nvram +7] init_nvram for model(49)
  167. usage: nvram [get name] [set name=value] [unset name] [show] [commit] [save] [restore] [erase] [fb_save file]
  168. usage: nvram [save_ap file] [save_rp_2g file] [save_rp_5g file] [save_rp_5g2 file]

  169. FA on.
  170. Override FA nvram...
  171. ctf: module license 'Proprietary' taints kernel.
  172. Disabling lock debugging due to kernel taint
  173. et_module_init: passivemode set to 0x0
  174. et_module_init: txworkq set to 0x1
  175. et_module_init: et_txq_thresh set to 0xce4
  176. aux0: Broadcom BCM47XX 10/100/1000 Mbps Ethernet Controller 6.37.14.126 (r561982)
  177. eth0: Broadcom BCM47XX 10/100/1000 Mbps Ethernet Controller 6.37.14.126 (r561982)
  178. et_probe: mvlan vid[0]: 0
  179. et_probe: mvlan vid[1]: 0

  180. et_probe: mvlan en 0
  181. eth1: Broadcom BCM47XX 10/100/1000 Mbps Ethernet Controller 6.37.14.126 (r561982)
  182. set_wltxpower(0x022d): unit: 0, txpower: 100
  183. set_wltxpower(0x022d): unit: 1, txpower: 100
  184. dpsta_init: msglevel set to 0x1
  185. hotplug net INTERFACE=aux0 ACTION=add
  186. hotplug net INTERFACE=eth1 ACTION=add
  187. hotplug net INTERFACE=eth0 ACTION=add
  188. hotplug net INTERFACE=dpsta ACTION=add
  189. wl_module_init: passivemode set to 0x0
  190. wl_module_init: igs set to 0x0
  191. wl_module_init: txworkq set to 0x1
  192. eth2: Broadcom BCM4360 802.11 Wireless Controller 6.37.14.126 (r561982)
  193. hotplug net INTERFACE=eth2 ACTION=add
  194. eth3: Broadcom BCM4360 802.11 Wireless Controller 6.37.14.126 (r561982)
  195. hotplug net INTERFACE=eth3 ACTION=add
  196. hotplug net: add net eth3.
  197. hotplug net(eth3): skip 2. usb_path /sys/devices/pci0002:00/0002:00:00.0/0002:02:00.0.
  198. 1: check_action 0: 1(preinit)
  199. start jffs2: 4, 65798144
  200. Empty flash at 0x006c6434 ends at 0x006c6800
  201. Empty flash at 0x006d2118 ends at 0x006d2800
  202. Empty flash at 0x010119d0 ends at 0x01012000
  203. Empty flash at 0x0101e648 ends at 0x0101e800
  204. Empty flash at 0x02354a0c ends at 0x02355000
  205. Empty flash at 0x031a9a0c ends at 0x031aa000
  206. Empty flash at 0x031b7430 ends at 0x031b7800
  207. JFFS2 warning: (104) jffs2_do_read_inode_internal: no data nodes found for ino #73930
  208. /jffs/.asusrouter killdon: errno: 3 pid 125
  209. 1: check_action 0: 1(preinit)
  210. JFFS2 warning: (1) jffs2_do_read_inode_internal: no data nodes found for ino #73930
  211. start_logger:
  212. _ifconfig: name=eth1 flags=1043 IFUP addr= netmask=
  213. et0: et_mvlan_netdev_event: event 16 for vlan1 mvlan_en 0
  214. et0: et_mvlan_netdev_event: event 5 for vlan1 mvlan_en 0
  215. hotplug net INTERFACE=vlan1 ACTION=add
  216. et0: et_mvlan_netdev_event: event 16 for vlan2 mvlan_en 0
  217. et0: et_mvlan_netdev_event: event 5 for vlan2 mvlan_en 0
  218. hotplug net INTERFACE=vlan2 ACTION=add
  219. update_lan_state(lan_, 0, 0)
  220. generate_wl_para(0x0c15): unit 0 subunit -1
  221. generate_wl_para(0x0fde): bw: 0
  222. generate_wl_para(0x0fe0): chanspec: 0
  223. generate_wl_para(0x0fe1): bw_cap: 3
  224. generate_wl_para(0x0fe7): obss_coex: 1
  225. wlconf_pre(0x114f): set vhtmode 1
  226. generate_wl_para(0x0c15): unit 1 subunit -1
  227. generate_wl_para(0x0fde): bw: 0
  228. generate_wl_para(0x0fe0): chanspec: 0
  229. generate_wl_para(0x0fe1): bw_cap: 7
  230. generate_wl_para(0x0fe7): obss_coex: 0
  231. wlconf_pre(0x114f): set vhtmode 1
  232. vlan1et0: et_mvlan_netdev_event: event 13 for vlan1 mvlan_en 0
  233. : cmd=14 et0: et_mvlan_netdev_event: event 1 for vlan1 mvlan_en 0
  234. (errno 95): Operation not supported
  235. _ifconfig: name=vlan1 flags=1243 IFUP addr= netmask=
  236. hotplug net INTERFACE=br0 ACTION=add
  237. _ifconfig: name=eth1 flags=1243 IFUP addr= netmask=
  238. _ifconfig: name=eth2 flags=1243 IFUP addr= netmask=
  239. generate_wl_para(0x0c15): unit 0 subunit -1
  240. generate_wl_para(0x0fde): bw: 0
  241. generate_wl_para(0x0fe0): chanspec: 0
  242. generate_wl_para(0x0fe1): bw_cap: 3
  243. generate_wl_para(0x0fe7): obss_coex: 1
  244. generate_wl_para(0x0c15): unit 0 subunit 1
  245. generate_wl_para(0x0c15): unit 0 subunit 2
  246. generate_wl_para(0x0c15): unit 0 subunit 3

  247. start_lan: setting MAC address of bridge br0 as 00:46:BC:8D:5E:71
  248. _ifconfig: name=br0 flags=1243 IFUP addr=192.168.1.1 netmask=255.255.255.0
  249. _ifconfig: name=lo flags=1043 IFUP addr=127.0.0.1 netmask=255.0.0.0
  250. _ifconfig: name=lo:0 flags=1043 IFUP addr=127.0.1.1 netmask=255.0.0.0
  251. route_manip: cmd=ADD name=lo addr=127.0.0.0 netmask=255.0.0.0 gateway=0.0.0.0 metric=0
  252. update_lan_state(lan_, 2, 0)
  253. nat_rule: stop_nat_rules 1.
  254. stop_nat_rules: apply the redirect_rules state 0 ret 0
  255. start_lan 2965
  256. # wanduck: Got LAN(-1) information:
  257. wanduck: delay 1 seconds before the first detect...
  258. wanduck: delay 2 seconds before the first detect...
  259. [1 preinit:start_dnsmasq +17] begin
  260. [1 preinit:stop_dnsmasq +17] begin
  261. [1 preinit:stop_stubby +17] begin
  262. [1 preinit:stop_stubby +17] end
  263. [1 preinit:stop_dnsmasq +17] end
  264. [1 preinit:start_stubby +17] begin
  265. [1 preinit:start_dnsmasq +17] end
  266. start_lan_port(0) 1
  267. illegal, cannot enable DualWAN
  268. wanduck: delay 3 seconds before the first detect...
  269. TZ watchdog
  270. msgget ok
  271. disk_monitor: starting...
  272. disk_monitor: day=5, week=6, time=13:5.
  273. disk_monitor: decide if scan the target...
  274. disk_monitor: 0: wait_second=36000...
  275. disk_monitor: 1: wait_second=36000...
  276. disk_monitor: wait_second=36000...
  277. disk_monitor: Pause...

  278. [bwdpi check] starting...
  279. Couldn't get the enabled rules of Parental-control correctly!
  280. rc: ==> binding interface(vlan1,eth1,eth2,wds0.*,wds1.*,wds2.*) for lldpd
  281. RAST 18: ROAMAST Start...
  282. wanduck: delay 4 seconds before the first detect...
  283. [312 watchdog:btn_check +19] button RESET pressed
  284. [312 watchdog:btn_check +19] button RESET pressed
  285. [312 watchdog:btn_check +19] button RESET pressed
  286. [312 watchdog:btn_check +19] button RESET pressed
  287. [312 watchdog:btn_check +19] button RESET pressed
  288. [312 watchdog:btn_check +19] button RESET pressed
  289. [312 watchdog:btn_check +19] button RESET pressed
  290. [312 watchdog:btn_check +19] button RESET pressed
  291. [312 watchdog:btn_check +19] button RESET pressed
  292. [312 watchdog:btn_check +20] button RESET pressed
  293. wanduck: delay 5 seconds before the first detect...
  294. [312 watchdog:btn_check +20] button RESET pressed
  295. [312 watchdog:btn_check +20] button RESET pressed
  296. [312 watchdog:btn_check +20] button RESET pressed
  297. [312 watchdog:btn_check +20] button RESET pressed
  298. [312 watchdog:btn_check +20] button RESET pressed
  299. [312 watchdog:btn_check +20] button RESET pressed
  300. [312 watchdog:btn_check +20] button RESET pressed
  301. [312 watchdog:btn_check +20] button RESET pressed
  302. [312 watchdog:btn_check +20] button RESET pressed
  303. [312 watchdog:btn_check +21] button RESET pressed
  304. wanduck(0): NC send SYS_WAN_MODEM_OFFLINE_EVENT.
  305. [312 watchdog:btn_check +21] button RESET pressed

  306. # Enable direct rule
  307. wanduck(0): NC send SYS_WAN_CABLE_UNPLUGGED_EVENT.
  308. [312 watchdog:btn_check +21] button RESET pressed
  309. You can release RESET button now!
  310. [312 watchdog:btn_check +21] button RESET pressed
  311. You can release RESET button now!
  312. [312 watchdog:btn_check +21] button RESET pressed
  313. You can release RESET button now!
  314. vlan1: cmd=14 (errno 95): Operation not supported
  315. [312 watchdog:btn_check +21] button RESET pressed
  316. You can release RESET button now!
  317. [312 watchdog:btn_check +21] button RESET pressed
  318. You can release RESET button now!
  319. [312 watchdog:btn_check +21] button RESET pressed
  320. You can release RESET button now!
  321. [rast_init_bssinfo]: WIF[eth1], idx[0]
  322. rssi threshold: [0]
  323. rssi hit count: [6]
  324. idle period: [20]
  325. idle rate: [10]
  326. [rast_init_bssinfo]: WIF[eth2], idx[1]
  327. rssi threshold: [-55]
  328. rssi hit count: [3]
  329. idle period: [15]
  330. idle rate: [20]
  331. [rast_init_bssinfo]: TotalWI[2]

  332. RAST 21: ipc accept socket...
  333. [312 watchdog:btn_check +21] button RESET pressed
  334. You can release RESET button now!
  335. [312 watchdog:btn_check +21] button RESET pressed
  336. You can release RESET button now!
  337. [Mastiff]init
  338. [312 watchdog:btn_check +22] button RESET pressed
  339. You can release RESET button now!
  340. [312 watchdog:btn_check +22] button RESET pressed
  341. You can release RESET button now!
  342. [312 watchdog:btn_check +22] button RESET pressed
  343. You can release RESET button now!
  344. [312 watchdog:btn_check +22] button RESET pressed
  345. You can release RESET button now!
  346. [312 watchdog:btn_check +22] button RESET pressed
  347. You can release RESET button now!
  348. start_wan: start_waet0: et_mvlan_netdev_event: event 8 for vlan2 mvlan_en 0
  349. n_if(0)!
  350. [1 preinit:start_wan_if +et0: et_mvlan_netdev_event: event 13 for vlan2 mvlan_en 0
  351. 22] unit=0.
  352. et0: et_mvlan_netdev_event: event 1 for vlan2 mvlan_en 0

  353. update_wan_state(wan0_, 0, 0)
  354. convert_wan_nvram(wan0_)
  355. ** wan_ifname: vlan2 is NOT UP
  356. _ifconfig: name=vlan2 flags=1043 IFUP addr= netmask=
  357. update_wan_state(wan0_, 1, 0)
  358. start_wan_if(0x0697): ifup:vlan2
  359. _ifconfig: name=vlan2 flags=1043 IFUP addr= netmask=
  360. start_wan_if(0x06ad): start auth:0
  361. start_auth:: done
  362. start_wan_if(0x06b7): start udhcpc:vlan2, 0
  363. start_wan_if(): End.
  364. udhcpc_wan:: deconfig
  365. _ifconfig: name=vlan2 flags=1043 IFUP addr=0.0.0.0 netmask=
  366. wan_down(vlan2)
  367. wan_down(vlan2): .
  368. stop_auth:: done
  369. route_manip: cmd=DEL name=vlan2 addr=0.0.0.0 netmask=0.0.0.0 gateway=(null) metric=0
  370. update_wan_state(wan0_, 3, 0)
  371. update_wan_state(wan0_, 4, 3)
  372. udhcpc:: deconfig done
  373. [312 watchdog:btn_check +22] button RESET pressed
  374. You can release RESET button now!
  375. [312 watchdog:btn_check +22] button RESET pressed
  376. You can release RESET button now!
  377. [312 watchdog:btn_check +22] button RESET pressed
  378. You can release RESET button now!
  379. [312 watchdog:btn_check +22] button RESET pressed
  380. You can release RESET button now!
  381. [312 watchdog:btn_check +22] button RESET pressed
  382. You can release RESET button now!
  383. [312 watchdog:btn_check +23] button RESET pressed
  384. You can release RESET button now!
  385. [312 watchdog:btn_check +23] button RESET pressed
  386. You can release RESET button now!
  387. Enable USB power.
  388. Start USB with the original procedure.
  389. start_usb
  390. no tune_bdflush
  391. [312 watchdog:btn_check +23] button RESET pressed
  392. You can release RESET button now!
  393. xhci_hcd 0000:00:0c.0: Failed to enable MSI-X
  394. xhci_hcd 0000:00:0c.0: failed to allocate MSI entry
  395. usb usb1: No SuperSpeed endpoint companion for config 1  interface 0 altsetting 0 ep 129: using minimum values
  396. [312 watchdog:btn_check +23] button RESET pressed
  397. You can release RESET button now!
  398. [312 watchdog:btn_check +23] button RESET pressed
  399. You can release RESET button now!
  400. [312 watchdog:btn_check +23] button RESET pressed
  401. You can release RESET button now!
  402. [312 watchdog:btn_check +23] button RESET pressed
  403. You can release RESET button now!
  404. csw_retry 100
  405. [312 watchdog:btn_check +23] button RESET pressed
  406. You can release RESET button now!
  407. [312 watchdog:btn_check +23] button RESET pressed
  408. You can release RESET button now!
  409. [312 watchdog:btn_check +23] button RESET pressed
  410. You can release RESET button now!
  411. [312 watchdog:btn_check +24] button RESET pressed
  412. You can release RESET button now!
  413. [312 watchdog:btn_check +24] button RESET pressed
  414. You can release RESET button now!
  415. [312 watchdog:btn_check +24] button RESET pressed
  416. You can release RESET button now!
  417. [312 watchdog:btn_check +24] button RESET pressed
  418. You can release RESET button now!
  419. [312 watchdog:btn_check +24] button RESET pressed
  420. You can release RESET button now!
  421. [312 watchdog:btn_check +24] button RESET pressed
  422. You can release RESET button now!
复制代码



我的恩山、我的无线 The best wifi forum is right here.
 楼主| 发表于 2022-1-8 11:53 | 显示全部楼层
TTL里中断启动,CFE下输入help无效,应该是CFE未解锁,是不是只能改SPI启动或者更换NAND闪存来救砖了
我的恩山、我的无线 The best wifi forum is right here.
回复

使用道具 举报

 楼主| 发表于 2022-1-8 12:58 | 显示全部楼层
本帖最后由 wz161996 于 2022-1-8 13:02 编辑

刚发完贴,在论坛网件板块闲逛,无意中看到一帖子,突发灵感尝试一下,竟然成功了。。
原贴地址:https://www.right.com.cn/forum/thread-7510553-1-1.html

帖子中说可以在CFE下刷CFE,就在终端中CFE下试了一下flash命令,结果
竟然响应了flash命令的使用方法,有希望。。于是继续查资料,结合论坛里K3改双启动后刷入CFE的命令,以及上面帖子中的命令,最终使用之前刷的1.3.0.7版本CFE,在CFE下成功刷入,然后nvram erase,reboot,成功开机。

本帖子中包含更多资源

您需要 登录 才可以下载或查看,没有账号?立即注册

×

点评

能具体说下这个流程吗?谢谢!  详情 回复 发表于 2022-8-30 15:58
我的恩山、我的无线 The best wifi forum is right here.
回复

使用道具 举报

发表于 2022-8-29 08:17 | 显示全部楼层
我的R7000改AC68U后,想还原成R7000,也是刷入自己备份的CFE成砖了,我对比了一下备份的CFE和论坛的,应该是备份不对。刚买了TTL-USB线,目前正在找攻略。
我的恩山、我的无线 The best wifi forum is right here.
回复

使用道具 举报

发表于 2022-8-30 15:58 | 显示全部楼层
wz161996 发表于 2022-1-8 12:58
刚发完贴,在论坛网件板块闲逛,无意中看到一帖子,突发灵感尝试一下,竟然成功了。。
原贴地址:https:// ...

能具体说下这个流程吗?谢谢!

点评

出现device 后 按CTRL+C 无效,楼主碰到过吗。  详情 回复 发表于 2023-3-9 22:01
我的恩山、我的无线 The best wifi forum is right here.
回复

使用道具 举报

发表于 2022-9-1 22:08 | 显示全部楼层
编程器救砖

点评

有编程器固件吗?求分享  详情 回复 发表于 2023-8-17 12:16
我的恩山、我的无线 The best wifi forum is right here.
回复

使用道具 举报

发表于 2023-3-9 22:01 | 显示全部楼层
本帖最后由 flice 于 2023-3-15 00:20 编辑
willcy 发表于 2022-8-30 15:58
能具体说下这个流程吗?谢谢!
网上资料搜到的,证实可用。
tftpserver下放cfe,直接cfe下刷
flash -noheader 192.168.1.22:cfe.bin flash0.boot

我的恩山、我的无线 The best wifi forum is right here.
回复

使用道具 举报

发表于 2023-8-17 12:16 | 显示全部楼层

有编程器固件吗?求分享
我的恩山、我的无线 The best wifi forum is right here.
回复

使用道具 举报

您需要登录后才可以回帖 登录 | 立即注册

本版积分规则

有疑问请添加管理员QQ86788181|手机版|小黑屋|Archiver|恩山无线论坛(常州市恩山计算机开发有限公司版权所有) ( 苏ICP备05084872号 )

GMT+8, 2024-3-29 15:46

Powered by Discuz! X3.5

© 2001-2024 Discuz! Team.

| 江苏省互联网有害信息举报中心 举报信箱:js12377 | @jischina.com.cn 举报电话:025-88802724 本站不良内容举报信箱:68610888@qq.com 举报电话:0519-86695797

快速回复 返回顶部 返回列表