|
|
尝试用TTL通过tftp上传固件后还是一样？有没有其他方法可以救回 Please choose the operation:
1: Load System code to SDRAM via TFTP.
2: Load System code then write to Flash via TFTP.
3: Boot System code via Flash (default).
4: Entr boot command line interface.
7: Load Boot Loader code then write to Flash via Serial.
9: Load Boot Loader code then write to Flash via TFTP.
You choosed 9
9: Load Boot Loader code then write to Flash via TFTP.
Warning!! Erase Boot Loader code in Flash then burn new one. Are you sure?(Y/N)
Please Input new ones /or Ctrl-C to discard
Input device IP (192.168.1.1) ==:
Input server IP (192.168.1.70) ==:
Input Uboot filename (u-boot_nand.img) ==:1.trx
No ART partition found
MAC0 addr:0:3:7f:ba:db:ad
PHY ID1: 0x4d
PHY ID2: 0xd0b1
ipq40xx_ess_sw_init done
eth0
preferred nic: eth0
eth0 PHY0 up Speed :1000 Full duplex
eth0 PHY1 Down Speed :10 Half duplex
eth0 PHY2 Down Speed :10 Half duplex
eth0 PHY3 Down Speed :10 Half duplex
eth0 PHY4 Down Speed :10 Half duplex
switch prereq:0
Using eth0 device
TFTP from server 192.168.1.70; our IP address is 192.168.1.1
Filename '1.trx'.
Load address: 0x84000000
Loading: Got ARP REPLY, set eth addr (fc:aa:14:bd:51:af)
####Got ARP REQUEST, return our IP
#############################################################
#################################################################
#################################################################
#####################################################Got ARP REQUEST, r eturn our IP
############
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
####Got ARP REQUEST, return our IP
#############################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
################################
done
Bytes transferred = 21447576 (1474398 hex)
NetBootFileXferSize= 01474398
resetting ...
Format: Log Type - Time(microsec) - Message - Optional Info
Log Type: B - Since Boot(Power On Reset), D - Delta, S - Statistic
S - QC_IMAGE_VERSION_STRING=BOOT.BF.3.1.1-00110
S - IMAGE_VARIANT_STRING=DAACANAZA
S - OEM_IMAGE_VERSION_STRING=CRM
S - Boot Config, 0x00000025
S - Reset status Config, 0x00000010
S - Core 0 Frequency, 0 MHz
B - 261 - PBL, Start
B - 1338 - bootable_media_detect_entry, Start
B - 2607 - bootable_media_detect_success, Start
B - 2622 - elf_loader_entry, Start
B - 4028 - auth_hash_seg_entry, Start
B - 6177 - auth_hash_seg_exit, Start
B - 74171 - elf_segs_hash_verify_entry, Start
B - 195956 - PBL, End
B - 195980 - SBL1, Start
B - 287996 - pm_device_init, Start
D - 7 - pm_device_init, Delta
B - 289488 - boot_flash_init, Start
D - 74240 - boot_flash_init, Delta
B - 368031 - boot_config_data_table_init, Start
D - 13971 - boot_config_data_table_init, Delta - (419 Bytes)
B - 384752 - clock_init, Start
D - 7922 - clock_init, Delta
B - 396109 - CDT version:2,Platform ID:8,Major ID:1,Minor ID:0,Subtype:1
B - 399523 - sbl1_ddr_set_params, Start
B - 404617 - cpr_init, Start
D - 2 - cpr_init, Delta
B - 408998 - Pre_DDR_clock_init, Start
D - 4 - Pre_DDR_clock_init, Delta
D - 13169 - sbl1_ddr_set_params, Delta
B - 422303 - pm_driver_init, Start
D - 2 - pm_driver_init, Delta
B - 492199 - sbl1_wait_for_ddr_training, Start
D - 28 - sbl1_wait_for_ddr_training, Delta
B - 507744 - Image Load, Start
D - 143834 - QSEE Image Loaded, Delta - (268920 Bytes)
B - 652004 - Image Load, Start
D - 2115 - SEC Image Loaded, Delta - (2048 Bytes)
B - 662213 - Image Load, Start
D - 197579 - APPSBL Image Loaded, Delta - (469819 Bytes)
B - 860185 - QSEE Execution, Start
D - 56 - QSEE Execution, Delta
B - 866417 - SBL1, End
D - 672438 - SBL1, Delta
S - Flash Throughput, 2098 KB/s (741206 Bytes, 353251 us)
S - DDR Frequency, 672 MHz
U-Boot 2012.07-06692-gf5cb475-dirty [local,local] (Mar 09 2017 - 14:02:58)
RT-AC82U bootloader version: 1.0.0.9
smem ram ptable found: ver: 1 len: 3
ASUS RT-AC82U gpio init : wps / reset pin
DRAM: 256 MiB
machid : 0x8010001
Maximum malloc length: 4096 KBytes
mem_malloc_start/brk/end: 0x86ed0000/86ed0000/872f0000
Relocation offset: 0
NAND: ID = 9580f1c2
Vendor = c2
Device = f1
ONFI device found
SF NAND unsupported id:ff:ff:ff:ffSF: Unsupported manufacturer ff
ipq_spi: SPI Flash not found (bus/cs/speed/mode) = (0/0/48000000/0)
128 MiB
PCI0 Link Intialized
In: serial
Out: serial
Err: serial
Check bootloader area ...
name : offset size
0:SBL1 : 00000000 00080000
0:MIBIB : 00080000 00080000
0 SEE : 00100000 00100000
0:CDT : 00200000 00080000
0:APPSBL : 00280000 00140000
0:APPSBLENV : 003c0000 00040000
machid: 8010001
flash_type: 2
Creating 1 MTD partitions on "nand0":
0x00400000-0x08000000 : "mtd=2"
UBI: attaching mtd1 to ubi0
UBI: physical eraseblock size: 131072 bytes (128 KiB)
UBI: logical eraseblock size: 126976 bytes
UBI: smallest flash I/O unit: 2048
UBI: VID header offset: 2048 (aligned 2048)
UBI: data offset: 4096
UBI: max. sequence number: 2569
UBI: attached mtd1 to ubi0
UBI: MTD device name: "mtd=2"
UBI: MTD device size: 124 MiB
UBI: number of good PEBs: 991
UBI: number of bad PEBs: 1
UBI: number of corrupted PEBs: 0
UBI: max. allowed volumes: 128
UBI: wear-leveling threshold: 4096
UBI: number of internal volumes: 1
UBI: number of user volumes: 6
UBI: available PEBs: 29
UBI: total number of reserved PEBs: 962
UBI: number of PEBs reserved for bad PEB handling: 9
UBI: max/mean erase counter: 41/3
UBI: image sequence number: 1175092700
UBI: vol_id reserved_pebs alignment data_pad vol_type usable_leb_size us ed_ebs used_bytes last_eb_bytes corrupted upd_marker name_len name
UBI: 0 3 1 0 dynamic 1f000 3 5d000 1f000 0 0 5 nvram
UBI: 1 1 1 0 dynamic 1f000 1 1f000 1f000 0 0 7 Factory
UBI: 2 1 1 0 dynamic 1f000 1 1f000 1f000 0 0 8 Factory2
UBI: 3 18d 1 0 dynamic 1f000 18d 3013000 1f000 0 0 5 linux
UBI: 4 18d 1 0 dynamic 1f000 18d 3013000 1f000 0 0 6 linux2
UBI: 5 96 1 0 dynamic 1f000 96 122a000 1f000 0 0 5 jffs2
UBI: 7fffefff 2 1 0 dynamic 1f000 2 3e000 2 0 0 d layout volum e
Read 0x1f000 bytes from volume [Factory] offset 0x0 to 86eb0ce0
EEPROM set 0: OK (version 15)
Read 0x1f000 bytes from volume [Factory2] offset 0x0 to 86eb0ce0
EEPROM set 1: OK (version 15)
Read 0x1f000 bytes from volume [Factory] offset 0x0 to 86ed1168
Select EEPROM set 0 at offset 0x0.
Please choose the operation:
1: Load System code to SDRAM via TFTP.
2: Load System code then write to Flash via TFTP.
3: Boot System code via Flash (default).
4: Entr boot command line interface.
7: Load Boot Loader code then write to Flash via Serial.
9: Load Boot Loader code then write to Flash via TFTP. 0
3: Boot System code via Flash (default).
RT-AC82U bootloader version: 1.0.0.9
MAC Address: 2C:FD:A1:03:78:E0
Read 0x40 bytes from volume [linux] offset 0x0 to 84000000
FIT/FDT format image found at 0x84000000, size 0x01474318
Read 0x1474358 bytes from volume [linux] offset 0x0 to 84000000
## Booting kernel from FIT Image at 84000000 ...
Using 'config@1' configuration
Trying 'kernel@1' kernel subimage
Description: ARM OpenWrt Linux-3.0
Type: Kernel Image
Compression: lzma compressed
Data Start: 0x840000e0
Data Size: 2111104 Bytes = 2 MiB
Architecture: ARM
OS: Linux
Load Address: 0x80208000
Entry Point: 0x80208000
Hash algo: crc32
Hash value: 4be9440e
## Loading init Ramdisk from FIT Image at 84000000 ...
Using 'config@1' configuration
Trying 'rootfs@1' ramdisk subimage
Description: Root File System
Type: RAMDisk Image
Compression: lzma compressed
Data Start: 0x84203840
Data Size: 19296598 Bytes = 18.4 MiB
Architecture: ARM
Hash algo: crc32
Hash value: 1d7febe9
## Flattened Device Tree from FIT Image at 84000000
Using 'config@1' configuration
Trying 'fdt@1' FDT blob subimage
Description: ARM OpenWrt qcom-ipq40xx-ap.dkxx device tree blob
Type: Flat Device Tree
Compression: uncompressed
Data Start: 0x8546aa94
Data Size: 38253 Bytes = 37.4 KiB
Architecture: ARM
Hash algo: crc32
Hash value: 090c1d07
Hash algo: sha1
Hash value: eff9cd08dab2d63c4552917d90f034a85275897c
Booting using the fdt blob at 0x8546aa94
Read 0x28 bytes from volume [linux2] offset 0x0 to 86ecfc38
Uncompressing Kernel Image ... OK
Loading Device Tree to 86ec3000, end 86ecf56c ... OK
Device nand2 not found!
Using machid 0x8010001 from environment
Starting kernel ...
|
|
简体中文
繁體中文
English
日本語
Deutsch
한국 사람
بالعربية
TÜRKÇE
português
คนไทย
IP卡
狗仔卡
发表于 2022-1-21 00:21
置顶卡
沉默卡
喧嚣卡
顶贴卡
显身卡