找回密码
 立即注册

QQ登录

只需一步,快速开始

搜索
广告投放联系QQ68610888
楼主: 5106***

[其它] 打造最强华为海思hi3798mv100/mv200/mv300机顶盒NAS服务器系统

  [复制链接]
发表于 2022-5-8 11:19 | 显示全部楼层
楼主能帮忙看一下我的这个怎么刷吗!!(固件信息NBD8008t-q  没有分区信息没法用HItool刷)
Bootrom start
Boot from NAND
Starting fastboot ...

System startup
DDRS
Reg Version:  v1.1.0
Reg Time:     2015/5/11  10:55:13
Reg Name:     hi3798mdmo1b_hi3798mv100_ddr3_1gbyte_16bitx2_2layers_nand.reg

Relocate Boot to DDR

Jump to DDR

Fastboot 3.3.0 (root@) (Jul 22 2017 - 22:22:54)

Fastboot:      Version 3.3.0
Build Date:    Jul 22 2017, 22:23:21
CPU:           Hi3798Mv100
Boot Media:    NAND
DDR Size:      1GB

Check nand flash controller v610. found
Special NAND id table Version 1.36
Nand ID: 0xC2 0xF1 0x80 0x95 0x02 0x00 0x00 0x00
Nand: Unknown NAND 128MiB 3,3V 8-bit
Nand(HW-Auto): Block:128KB Page:2KB OOB:64B ECC:4bit/512 Chip:128MB*1

MMC/SD controller initialization.
No MMC/SD card detect when read `SDIO_CARD_DETECT` pin.

*** Warning - bad CRC or NAND, using default environment

Boot Env on NAND
    Env Offset:          0x00080000
    Env Size:            0x00010000
    Env Range:           0x00010000
HI_OTP_LockIdWord,327: ID_WORD have already been locked

SDK Version: HiSTBLinuxV100R003C00SPC062

Reserve Memory
    Start Addr:          0x1FFFE000
    Bound Addr:          0x8D2C000
    Free  Addr:          0x1F8FC000
    Alloc Block:  Addr        Size
                  0x1FBFD000       4194304
                  0x1F8FC000       3145728

Press Ctrl+C to stop autoboot

NAND read: device 0 offset 0x600000, size 0x700000
pure data length is 7340032, len_incl_bad is 7340032
request to read 0x700000, and read 0x700000 successfully!
7340032 bytes read: OK
## Booting kernel from Legacy Image at 81000000 ...
   Image Name:   Linux-3.10.0_s40
   Image Type:   ARM Linux Kernel Image (uncompressed)
   Data Size:    4525512 Bytes = 4.3 MiB
   Load Address: 02000000
   Entry Point:  02000000
   Verifying Checksum ... OK
   Loading Kernel Image ... OK
OK
There are some conflict between "booargs" and "bootargs_1G".
The param "mem mmz " in "bootargs_1G" will be ignored.

Starting kernel ...

Uncompressing Linux... done, booting the kernel.
Booting Linux on physical CPU 0x0
Linux version 3.10.0_s40 (root@ubuntu) (gcc version 4.4.1 (Hisilicon_v200(gcc4.4-290+glibc-2.11+eabi+nptl)) ) #16 SMP Sat Jul 22 16:38:18 CST 2017
CPU: ARMv7 Processor [410fc075] revision 5 (ARMv7), cr=10c53c7d
CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
Machine: bigfish
cma: CMA: reserved 368 MiB at 09000000
cma: CMA: reserved 4 MiB at 08c00000
Memory policy: ECC disabled, Data cache writealloc
CPU: Hi3798Mv100
PERCPU: Embedded 8 pages/cpu @80d3b000 s11968 r8192 d12608 u32768
Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 130048
Kernel command line: mem=512M console=ttyAMA0,115200 root=/dev/mtdblock5 rootfstype=yaffs mtdparts=hinand:1M(boot),1M(bootargs),2M(baseparam),2M(logo),7M(kernel),115M(rootfs) mmz=ddr,0,0,366M
PID hash table entries: 2048 (order: 1, 8192 bytes)
Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
Memory: 512MB = 512MB total
Memory: 128540k/128540k available, 395748k reserved, 0K highmem
Virtual kernel memory layout:
    vector  : 0xffff0000 - 0xffff1000   (   4 kB)
    fixmap  : 0xfff00000 - 0xfffe0000   ( 896 kB)
    vmalloc : 0xa0800000 - 0xff000000   (1512 MB)
    lowmem  : 0x80000000 - 0xa0000000   ( 512 MB)
    pkmap   : 0x7fe00000 - 0x80000000   (   2 MB)
    modules : 0x7f000000 - 0x7fe00000   (  14 MB)
      .text : 0x80008000 - 0x80813bf8   (8239 kB)
      .init : 0x80814000 - 0x8086cec0   ( 356 kB)
      .data : 0x8086e000 - 0x808c01e8   ( 329 kB)
       .bss : 0x808c01e8 - 0x80936474   ( 473 kB)
SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1
Hierarchical RCU implementation.
NR_IRQS:192
sched_clock: 32 bits at 24MHz, resolution 41ns, wraps every 178956ms
Console: colour dummy device 80x30
Calibrating delay loop... 1949.69 BogoMIPS (lpj=974848)
pid_max: default: 32768 minimum: 301
Mount-cache hash table entries: 512
CPU: Testing write buffer coherency: ok
ftrace: allocating 20417 entries in 60 pages
CPU0: thread -1, cpu 0, socket 0, mpidr 80000000
Setting up static identity map for 0x80604038 - 0x80604090
CPU1: thread -1, cpu 1, socket 0, mpidr 80000001
CPU2: thread -1, cpu 2, socket 0, mpidr 80000002
CPU3: thread -1, cpu 3, socket 0, mpidr 80000003
Brought up 4 CPUs
SMP: Total of 4 processors activated (7829.50 BogoMIPS).
CPU: All CPU(s) started in SVC mode.
NET: Registered protocol family 16
DMA: preallocated 256 KiB pool for atomic coherent allocations
hw-breakpoint: found 5 (+1 reserved) breakpoint and 4 watchpoint registers.
hw-breakpoint: maximum watchpoint size is 8 bytes.
Serial: AMBA PL011 UART driver
uart:0: ttyAMA0 at MMIO 0xf8b00000 (irq = 81) is a PL011 rev2
console [ttyAMA0] enabled
uart:1: ttyAMA1 at MMIO 0xf8006000 (irq = 82) is a PL011 rev2
uart:2: ttyAMA2 at MMIO 0xf8b02000 (irq = 83) is a PL011 rev2
bio: create slab <bio-0> at 0
SCSI subsystem initialized
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
Linux video capture interface: v2.00
Advanced Linux Sound Architecture Driver Initialized.
Bluetooth: Core ver 2.16
NET: Registered protocol family 31
Bluetooth: HCI device and connection manager initialized
Bluetooth: HCI socket layer initialized
Bluetooth: L2CAP socket layer initialized
Bluetooth: SCO socket layer initialized
Switching to clocksource timer3
NET: Registered protocol family 2
TCP established hash table entries: 4096 (order: 3, 32768 bytes)
TCP bind hash table entries: 4096 (order: 3, 32768 bytes)
TCP: Hash tables configured (established 4096 bind 4096)
TCP: reno registered
UDP hash table entries: 256 (order: 1, 8192 bytes)
UDP-Lite hash table entries: 256 (order: 1, 8192 bytes)
NET: Registered protocol family 1
RPC: Registered named UNIX socket transport module.
RPC: Registered udp transport module.
RPC: Registered tcp transport module.
RPC: Registered tcp NFSv4.1 backchannel transport module.
NetWinder Floating Point Emulator V0.97 (double precision)
CPU PMU: probing PMU on CPU 0
hw perfevents: enabled with ARMv7 Cortex-A7 PMU driver, 5 counters available
VFS: Disk quotas dquot_6.5.2
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
squashfs: version 4.0 (2009/01/31) Phillip Lougher
jffs2: version 2.2. (NAND) 漏 2001-2006 Red Hat, Inc.
fuse init (API version 7.22)
msgmni has been set to 995
Block layer SCSI generic (bsg) driver version 0.4 loaded (major 254)
io scheduler noop registered
io scheduler deadline registered (default)
io scheduler cfq registered
brd: module loaded
loop: module loaded
Found Nand Flash Controller V610.
Nand ID: 0xC2 0xF1 0x80 0x95 0x02 0x00 0x00 0x00
Nand: Macronix NAND 128MiB 3,3V 8-bit
Nand(HW-Auto): Block:128KB Page:2KB OOB:64B ECC:4bit/512 Chip:128MB*1
6 cmdlinepart partitions found on MTD device hinand
Creating 6 MTD partitions on "hinand":
0x000000000000-0x000000100000 : "boot"
0x000000100000-0x000000200000 : "bootargs"
0x000000200000-0x000000400000 : "baseparam"
0x000000400000-0x000000600000 : "logo"
0x000000600000-0x000000d00000 : "kernel"
0x000000d00000-0x000008000000 : "rootfs"
libphy: himii: probed
Up port phy at 0x01 is connect
libphy: PHY himii:1f not found
PPP generic driver version 2.4.2
PPP BSD Compression module registered
PPP Deflate Compression module registered
usbcore: registered new interface driver cdc_wdm
usbcore: registered new interface driver usb-storage
usbcore: registered new interface driver usbserial
usbcore: registered new interface driver usbserial_generic
usbserial: USB Serial support registered for generic
usbcore: registered new interface driver ftdi_sio
usbserial: USB Serial support registered for FTDI USB Serial Device
usbcore: registered new interface driver option
usbserial: USB Serial support registered for GSM modem (1-port)
usbcore: registered new interface driver pl2303
usbserial: USB Serial support registered for pl2303
mousedev: PS/2 mouse device common for all mice
usbcore: registered new interface driver uvcvideo
USB Video Class driver (1.1.1)
usbcore: registered new interface driver btusb
hi_mci1: eMMC/MMC/SD Device NOT detected!
hi_mci0: eMMC/MMC/SD Device NOT detected!
usbcore: registered new interface driver usbhid
usbhid: USB HID core driver
usbcore: registered new interface driver snd-usb-audio
oprofile: using timer interrupt.
Netfilter messages via NETLINK v0.30.
nfnl_acct: registering with nfnetlink.
ip_tables: (C) 2000-2006 Netfilter Core Team
arp_tables: (C) 2002 David S. Miller
TCP: cubic registered
NET: Registered protocol family 10
NET: Registered protocol family 17
Bridge firewalling registered
Bluetooth: RFCOMM TTY layer initialized
Bluetooth: RFCOMM socket layer initialized
Bluetooth: RFCOMM ver 1.11
Bluetooth: BNEP (Ethernet Emulation) ver 1.3
Bluetooth: BNEP filters: protocol multicast
Bluetooth: BNEP socket layer initialized
Bluetooth: HIDP (Human Interface Emulation) ver 1.2
Bluetooth: HIDP socket layer initialized
8021q: 802.1Q VLAN Support v1.8
VFP support v0.3: implementor 41 architecture 2 part 30 variant 7 rev 5
ALSA device list:
  No soundcards found.
yaffs: dev is 32505861 name is "mtdblock5" rw
yaffs: passed flags ""
VFS: Mounted root (yaffs filesystem) on device 31:5.
Freeing unused kernel memory: 352K (80814000 - 8086c000)

            _ _ _ _ _ _ _ _ _ _ _ _
            \  _  _   _  _ _ ___
            / /__/ \ |_/
           / __   /  -  _ ___
          / /  / /  / /
  _ _ _ _/ /  /  \_/  \_ ______
___________\___\__________________

[RCS]: /etc/init.d/S00devs
[RCS]: /etc/init.d/S01udev
[RCS]: /etc/init.d/S80network
[RCS]: /etc/init.d/S90modules
Load hi_media.ko success.        (SDK_VERSION:[HiSTBLinuxV100R003C00SPC062] Build Time:[Jul 22 2017, 16:41:46])
Load hi_mmz.ko success.                (SDK_VERSION:[HiSTBLinuxV100R003C00SPC062] Build Time:[Jul 22 2017, 16:41:47])
Load hi_common.ko success.        (SDK_VERSION:[HiSTBLinuxV100R003C00SPC062] Build Time:[Jul 22 2017, 16:41:43])
Load hi_gpio.ko success.        (SDK_VERSION:[HiSTBLinuxV100R003C00SPC062] Build Time:[Jul 22 2017, 16:43:00])
Load hi_gpioi2c.ko success.        (SDK_VERSION:[HiSTBLinuxV100R003C00SPC062] Build Time:[Jul 22 2017, 16:44:02])
Load hi_i2c.ko success.          (SDK_VERSION:[HiSTBLinuxV100R003C00SPC062] Build Time:[Jul 22 2017, 16:44:01])
Mali: Mali device driver loaded
Load hi_tde.ko success.                (SDK_VERSION:[HiSTBLinuxV100R003C00SPC062] Build Time:[Jul 22 2017, 16:43:51])
DieID is locked!
Load hi_otp.ko success.          (SDK_VERSION:[HiSTBLinuxV100R003C00SPC062] Build Time:[Jul 22 2017, 16:44:15])
Load hi_demux.ko success.          (SDK_VERSION:[HiSTBLinuxV100R003C00SPC062] Build Time:[Jul 22 2017, 16:44:04])
Load hi_adec.ko success.          (SDK_VERSION:[HiSTBLinuxV100R003C00SPC062] Build Time:[Jul 22 2017, 16:44:41])
Load hi_vfmw.ko success.        (SDK_VERSION:[HiSTBLinuxV100R003C00SPC062] Build Time:[Jul 22 2017, 16:44:42])
Load hi_svdec.ko success.        (SDK_VERSION:[HiSTBLinuxV100R003C00SPC062] Build Time:[Jul 22 2017, 16:46:37])
[9292 ERROR-HI_PQ]RV_PQ_GetFlashPqBin[2968]Q bin param may not burned

[9299 ERROR-HI_PQ]:HI_DRV_PQ_Init[245]oad PQBin failed!
Load hi_pq.ko success.                (SDK_VERSION:[HiSTBLinuxV100R003C00SPC062] Build Time:[Jul 22 2017, 16:43:07])
Load hi_vpss.ko success.        (SDK_VERSION:[HiSTBLinuxV100R003C00SPC062] Build Time:[Jul 22 2017, 16:46:56])
Load hi_vdec.ko success.        (SDK_VERSION:[HiSTBLinuxV100R003C00SPC062] Build Time:[Aug  1 2017, 22:32:11])
Load hi_cipher.ko success.        (SDK_VERSION:[HiSTBLinuxV100R003C00SPC062] Build Time:[Jul 22 2017, 16:44:13])
Load hi_hdmi.ko success.        (SDK_VERSION:[HiSTBLinuxV100R003C00SPC062] Build Time:[Jul 22 2017, 16:43:13])
Load hi_adsp.ko success.        (SDK_VERSION:[HiSTBLinuxV100R003C00SPC062] Build Time:[Jul 22 2017, 16:44:26])
Load hi_aiao.ko success.          (SDK_VERSION:[HiSTBLinuxV100R003C00SPC062] Build Time:[Jul 22 2017, 16:44:28])
Load hi_vou.ko success.             (SDK_VERSION:[HiSTBLinuxV100R003C00SPC062] Build Time:[Jul 22 2017, 16:43:33])
Load hi_pvr.ko success.          (SDK_VERSION:[HiSTBLinuxV100R003C00SPC060] Build Time:[Feb  1 2016, 05:19:58])
Load hi_fb.ko success.        (SDK_VERSION:[HiSTBLinuxV100R003C00SPC062] Build Time:[Jul 22 2017, 16:43:47])
Load hi_ir.ko success.          (SDK_VERSION:[HiSTBLinuxV100R003C00SPC062] Build Time:[Jul 22 2017, 16:43:02])
Load hi_jpegdec.ko success.        (SDK_VERSION:[HiSTBLinuxV100R003C00SPC062] Build Time:[Jul 22 2017, 16:43:58])
Load hi_jpegenc.ko success.        (SDK_VERSION:[HiSTBLinuxV100R003C00SPC062] Build Time:[Jul 22 2017, 16:47:08])
Load hi_png.ko success.                (SDK_VERSION:[HiSTBLinuxV100R003C00SPC062] Build Time:[Jul 22 2017, 16:46:58])
Load hi_venc.ko success.        (SDK_VERSION:[HiSTBLinuxV100R003C00SPC062] Build Time:[Jul 22 2017, 16:47:30])
Load hi_aenc.ko success.          (SDK_VERSION:[HiSTBLinuxV100R003C00SPC062] Build Time:[Jul 22 2017, 16:47:29])
Load hi_keyled.ko success.        (SDK_VERSION:[HiSTBLinuxV100R003C00SPC062] Build Time:[Jul 22 2017, 16:47:26])
Load hi_vi.ko success.                (SDK_VERSION:[HiSTBLinuxV100R003C00SPC062] Build Time:[Jul 22 2017, 16:47:37])
enter temperature_control_thread
Load hi_pmoc.ko success.        (SDK_VERSION:[HiSTBLinuxV100R003C00SPC062] Build Time:[Jul 22 2017, 16:47:05])
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
hiusb-ehci hiusb-ehci.0: HIUSB EHCI
hiusb-ehci hiusb-ehci.0: new USB bus registered, assigned bus number 1
hiusb-ehci hiusb-ehci.0: irq 98, io mem 0xf9890000
hiusb-ehci hiusb-ehci.0: USB 0.0 started, EHCI 1.00
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
hiusb-ehci hiusb-ehci.1: HIUSB EHCI
hiusb-ehci hiusb-ehci.1: new USB bus registered, assigned bus number 2
hiusb-ehci hiusb-ehci.1: irq 94, io mem 0xf9930000
hiusb-ehci hiusb-ehci.1: USB 0.0 started, EHCI 1.00
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 1 port detected
ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
hiusb-ohci hiusb-ohci.0: HIUSB OHCI
hiusb-ohci hiusb-ohci.0: new USB bus registered, assigned bus number 3
hiusb-ohci hiusb-ohci.0: irq 99, io mem 0xf9880000
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 2 ports detected
hiusb-ohci hiusb-ohci.1: HIUSB OHCI
hiusb-ohci hiusb-ohci.1: new USB bus registered, assigned bus number 4
hiusb-ohci hiusb-ohci.1: irq 95, io mem 0xf9920000
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 1 port detected
tntfs: module license 'Commercial. For support email ntfs-support@tuxera.com.' taints kernel.
Disabling lock debugging due to kernel taint
Tuxera NTFS driver 3015.1.29.1.1 [Flags: R/W MODULE].
/
[RCS]: /etc/init.d/S99init
Compile file system used arm-hisiv200-linux-
2016-02-01 04:52:34 AM (alan@AmazingHost)
tar: can't open '/bin/update.tar.bz2': No such file or directory
chmod: *: No such file or directory
usb 3-1: new full-speed USB device number 2 using hiusb-ohci
input: RAPOO Rapoo 2.4G Wireless Device as /devices/platform/hiusb-ohci.0/usb3/3-1/3-1:1.0/input/input0
hid-generic 0003:24AE:1813.0001: input: USB HID v1.01 Keyboard [RAPOO Rapoo 2.4G Wireless Device] on usb-hiusb-ohci-1/input0
input: RAPOO Rapoo 2.4G Wireless Device as /devices/platform/hiusb-ohci.0/usb3/3-1/3-1:1.1/input/input1
hid-generic 0003:24AE:1813.0002: input: USB HID v1.01 Mouse [RAPOO Rapoo 2.4G Wireless Device] on usb-hiusb-ohci-1/input1
HIGO Version                :4.0.0.0 B01
HIGO Build Time                :Mar 26 2015 16:36:53
HIGO Adp Version        :4.0.0.0 V1R2 B02
HIGO Adp Build Time        :Mar 26 2015 16:37:03
dec file name:./logo720x576.gif
我的恩山、我的无线 The best wifi forum is right here.
回复

使用道具 举报

发表于 2022-5-9 16:23 | 显示全部楼层
不知道能不能将这个机器改造为软路由,做旁路由使用!那样将会有更大的用途!

点评

有docker,几条命令就可以旁路学习  详情 回复 发表于 2022-5-10 10:14
我的恩山、我的无线 The best wifi forum is right here.
回复

使用道具 举报

发表于 2022-5-10 10:14 | 显示全部楼层
yangstart 发表于 2022-5-9 16:23
不知道能不能将这个机器改造为软路由,做旁路由使用!那样将会有更大的用途!

有docker,几条命令就可以旁路学习

点评

能具体指引一下怎么做?  详情 回复 发表于 2022-10-27 14:43
我的恩山、我的无线 The best wifi forum is right here.
回复

使用道具 举报

发表于 2022-5-11 09:13 | 显示全部楼层
liuhu 发表于 2022-4-11 20:29
楼主能帮忙看看吗?我这个烽火hg680-j的盒子刷不了
Bootrom start
Boot from eMMC

可以刷
我的恩山、我的无线 The best wifi forum is right here.
回复

使用道具 举报

发表于 2022-6-2 07:59 | 显示全部楼层
没有刷成功。不知道是什么问题?CM101s  另一个cm101s-2两个都到这步就出错了。

本帖子中包含更多资源

您需要 登录 才可以下载或查看,没有账号?立即注册

×

点评

兄弟,刷的时候把盒子的网口连上网线就可以,你试试看  详情 回复 发表于 2022-7-1 23:39
我的恩山、我的无线 The best wifi forum is right here.
回复

使用道具 举报

发表于 2022-6-6 14:19 | 显示全部楼层
膜拜大佬

我的恩山、我的无线 The best wifi forum is right here.
回复

使用道具 举报

发表于 2022-6-21 22:35 | 显示全部楼层
创维e900高安版本本解决吗
我的恩山、我的无线 The best wifi forum is right here.
回复

使用道具 举报

发表于 2022-7-1 23:39 | 显示全部楼层
kingjoe 发表于 2022-6-2 07:59
没有刷成功。不知道是什么问题?CM101s  另一个cm101s-2两个都到这步就出错了。

兄弟,刷的时候把盒子的网口连上网线就可以,你试试看
我的恩山、我的无线 The best wifi forum is right here.
回复

使用道具 举报

发表于 2022-7-15 18:06 | 显示全部楼层
老大 厉害
我的恩山、我的无线 The best wifi forum is right here.
回复

使用道具 举报

发表于 2022-7-17 06:44 | 显示全部楼层
真箱子
我的恩山、我的无线 The best wifi forum is right here.
回复

使用道具 举报

发表于 2022-7-17 10:26 | 显示全部楼层
这个怎么破?


湖北电信的 创维E900

本帖子中包含更多资源

您需要 登录 才可以下载或查看,没有账号?立即注册

×

点评

不是可以卡刷吗,为什么你们都去烧录啊,短接用优盘卡刷一下多方便  详情 回复 发表于 2022-9-19 16:09
我的恩山、我的无线 The best wifi forum is right here.
回复

使用道具 举报

发表于 2022-7-18 15:38 | 显示全部楼层
哈哈,退网剩下一个盒子。
我的恩山、我的无线 The best wifi forum is right here.
回复

使用道具 举报

发表于 2022-7-23 16:57 | 显示全部楼层
求教大佬,如何实现usb设备自动识别挂载。
其他armbian盒子也有这个需求。
安装udevil的话,自动挂载路径只能是类似/mnt/sda1-usb-VendorCo_Product,不能是比如/mnt/sda1这种自定义的。
不知道海思系列的ubuntu,你是如何实现的。
我的恩山、我的无线 The best wifi forum is right here.
回复

使用道具 举报

发表于 2022-7-24 08:45 | 显示全部楼层
yezai163 发表于 2022-4-9 10:35
有卖成品的吗?实在是不想折腾买线啥的。

@所有人&#8197;还没刷好或者正在考虑开盲盒的群友们,可以看过来,这里直接上车!
https://item.taobao.com/item.htm?id=672356130441
这是群主刷好的盒子,hi3798mv100的开发用的原型机,出厂就是最新的固件,所有功能全部汇聚并测试好的。用户无需操心,真正开箱即用。下单购买用户优先支持解答疑难。
我的恩山、我的无线 The best wifi forum is right here.
回复

使用道具 举报

发表于 2022-7-29 22:50 | 显示全部楼层
感谢分享!华为悦盒ec6108v9c已刷可以用,具体要体验下
我的恩山、我的无线 The best wifi forum is right here.
回复

使用道具 举报

您需要登录后才可以回帖 登录 | 立即注册

本版积分规则

有疑问请添加管理员QQ86788181|手机版|小黑屋|Archiver|恩山无线论坛(常州市恩山计算机开发有限公司版权所有) ( 苏ICP备05084872号 )

GMT+8, 2024-4-26 02:01

Powered by Discuz! X3.5

© 2001-2024 Discuz! Team.

| 江苏省互联网有害信息举报中心 举报信箱:js12377 | @jischina.com.cn 举报电话:025-88802724 本站不良内容举报信箱:68610888@qq.com 举报电话:0519-86695797

快速回复 返回顶部 返回列表