|
楼主 |
发表于 2022-5-3 10:59
|
显示全部楼层
以下是 dmesg 的输出
- root@OpenWrt:~# dmesg
- [ 0.000000] Linux version 5.4.188 (xu@xu-virtual-machine) (gcc version 8.4.0 (OpenWrt GCC 8.4.0 r16554-1d4dea6d4f)) #0 Sat Apr 16 12:59:34 2022
- [ 0.000000] Board has DDR2
- [ 0.000000] Analog PMU set to hw control
- [ 0.000000] Digital PMU set to hw control
- [ 0.000000] SoC Type: MediaTek MT7620A ver:2 eco:6
- [ 0.000000] printk: bootconsole [early0] enabled
- [ 0.000000] CPU0 revision is: 00019650 (MIPS 24KEc)
- [ 0.000000] MIPS: machine is Asus RT-AC51U
- [ 0.000000] Initrd not found or empty - disabling initrd
- [ 0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
- [ 0.000000] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
- [ 0.000000] Zone ranges:
- [ 0.000000] Normal [mem 0x0000000000000000-0x0000000007ffffff]
- [ 0.000000] Movable zone start for each node
- [ 0.000000] Early memory node ranges
- [ 0.000000] node 0: [mem 0x0000000000000000-0x0000000007ffffff]
- [ 0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x0000000007ffffff]
- [ 0.000000] On node 0 totalpages: 32768
- [ 0.000000] Normal zone: 288 pages used for memmap
- [ 0.000000] Normal zone: 0 pages reserved
- [ 0.000000] Normal zone: 32768 pages, LIFO batch:7
- [ 0.000000] pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768
- [ 0.000000] pcpu-alloc: [0] 0
- [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 32480
- [ 0.000000] Kernel command line: console=ttyS0,57600 rootfstype=squashfs,jffs2
- [ 0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes, linear)
- [ 0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes, linear)
- [ 0.000000] Writing ErrCtl register=00035bf1
- [ 0.000000] Readback ErrCtl register=00035bf1
- [ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off
- [ 0.000000] Memory: 122288K/131072K available (4745K kernel code, 206K rwdata, 1048K rodata, 1224K init, 205K bss, 8784K reserved, 0K cma-reserved)
- [ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
- [ 0.000000] NR_IRQS: 256
- [ 0.000000] random: get_random_bytes called from start_kernel+0x358/0x54c with crng_init=0
- [ 0.000000] CPU Clock: 580MHz
- [ 0.000000] clocksource: systick: mask: 0xffff max_cycles: 0xffff, max_idle_ns: 583261500 ns
- [ 0.000000] systick: enable autosleep mode
- [ 0.000000] systick: running - mult: 214748, shift: 32
- [ 0.000000] clocksource: MIPS: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 6590553264 ns
- [ 0.000010] sched_clock: 32 bits at 290MHz, resolution 3ns, wraps every 7405115902ns
- [ 0.007611] Calibrating delay loop... 385.02 BogoMIPS (lpj=770048)
- [ 0.045493] pid_max: default: 32768 minimum: 301
- [ 0.050185] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes, linear)
- [ 0.057240] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes, linear)
- [ 0.071776] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041785100000 ns
- [ 0.081258] futex hash table entries: 256 (order: -1, 3072 bytes, linear)
- [ 0.087942] pinctrl core: initialized pinctrl subsystem
- [ 0.093612] NET: Registered protocol family 16
- [ 0.474655] mt7620-pci 10140000.pcie: PCIE0 no card, disable it(RST&CLK)
- [ 0.481162] mt7620-pci: probe of 10140000.pcie failed with error -1
- [ 0.510746] rt2880_gpio 10000600.gpio: registering 24 gpios
- [ 0.516229] rt2880_gpio 10000600.gpio: registering 24 irq handlers
- [ 0.522244] GPIO line 10 (enable-leds) hogged as output/low
- [ 0.527990] rt2880_gpio 10000688.gpio: registering 1 gpios
- [ 0.533337] rt2880_gpio 10000688.gpio: registering 1 irq handlers
- [ 0.544501] clocksource: Switched to clocksource systick
- [ 0.551104] NET: Registered protocol family 2
- [ 0.555548] IP idents hash table entries: 2048 (order: 2, 16384 bytes, linear)
- [ 0.563304] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 4096 bytes, linear)
- [ 0.571455] TCP established hash table entries: 1024 (order: 0, 4096 bytes, linear)
- [ 0.578865] TCP bind hash table entries: 1024 (order: 0, 4096 bytes, linear)
- [ 0.585705] TCP: Hash tables configured (established 1024 bind 1024)
- [ 0.592020] UDP hash table entries: 256 (order: 0, 4096 bytes, linear)
- [ 0.598370] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes, linear)
- [ 0.605409] NET: Registered protocol family 1
- [ 0.609655] PCI: CLS 0 bytes, default 32
- [ 0.616407] rt-timer 10000100.timer: maximum frequency is 1220Hz
- [ 0.624774] workingset: timestamp_bits=14 max_order=15 bucket_order=1
- [ 0.639628] squashfs: version 4.0 (2009/01/31) Phillip Lougher
- [ 0.645300] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
- [ 0.673582] Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled
- [ 0.681013] printk: console [ttyS0] disabled
- [ 0.685220] 10000c00.uartlite: ttyS0 at MMIO 0x10000c00 (irq = 20, base_baud = 2500000) is a Palmchip BK-3103
- [ 0.694838] printk: console [ttyS0] enabled
- [ 0.711374] printk: bootconsole [early0] disabled
- [ 0.736465] spi spi0.0: force spi mode3
- [ 0.755771] spi-nor spi0.0: w25q128 (16384 Kbytes)
- [ 0.765400] 4 fixed-partitions partitions found on MTD device spi0.0
- [ 0.778065] Creating 4 MTD partitions on "spi0.0":
- [ 0.787625] 0x000000000000-0x000000030000 : "u-boot"
- [ 0.798620] 0x000000030000-0x000000040000 : "u-boot-env"
- [ 0.810317] 0x000000040000-0x000000050000 : "factory"
- [ 0.821535] 0x000000050000-0x000001000000 : "firmware"
- [ 0.836226] 2 uimage-fw partitions found on MTD device firmware
- [ 0.848103] Creating 2 MTD partitions on "firmware":
- [ 0.858012] 0x000000000000-0x0000001e828c : "kernel"
- [ 0.869101] 0x0000001e828c-0x000000fb0000 : "rootfs"
- [ 0.880012] mtd: device 5 (rootfs) set to be root filesystem
- [ 0.893263] 1 squashfs-split partitions found on MTD device rootfs
- [ 0.905655] 0x00000056d000-0x000000fb0000 : "rootfs_data"
- [ 0.928631] gsw: setting port4 to ephy mode
- [ 0.937039] mtk_soc_eth 10100000.ethernet eth0 (uninitialized): port 3 link up (100Mbps/Full duplex)
- [ 0.955759] mtk_soc_eth 10100000.ethernet: loaded mt7620 driver
- [ 0.968361] mtk_soc_eth 10100000.ethernet eth0: mediatek frame engine at 0xb0100000, irq 5
- [ 0.985429] rt2880_wdt 10000120.watchdog: Initialized
- [ 0.997153] NET: Registered protocol family 10
- [ 1.010488] Segment Routing with IPv6
- [ 1.018010] NET: Registered protocol family 17
- [ 1.026942] 8021q: 802.1Q VLAN Support v1.8
- [ 1.044632] VFS: Mounted root (squashfs filesystem) readonly on device 31:5.
- [ 1.065693] Freeing unused kernel memory: 1224K
- [ 1.074737] This architecture does not have kernel memory protection.
- [ 1.087570] Run /sbin/init as init process
- [ 1.376461] random: fast init done
- [ 1.986622] init: Console is alive
- [ 1.993833] init: - watchdog -
- [ 3.420622] kmodloader: loading kernel modules from /etc/modules-boot.d/*
- [ 3.635304] usbcore: registered new interface driver usbfs
- [ 3.646413] usbcore: registered new interface driver hub
- [ 3.657139] usbcore: registered new device driver usb
- [ 3.674675] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
- [ 3.689736] ehci-fsl: Freescale EHCI Host controller driver
- [ 3.702634] ehci-platform: EHCI generic platform driver
- [ 3.723451] phy phy-usbphy.0: remote usb device wakeup disabled
- [ 3.735261] phy phy-usbphy.0: UTMI 16bit 30MHz
- [ 3.744124] ehci-platform 101c0000.ehci: EHCI Host Controller
- [ 3.755613] ehci-platform 101c0000.ehci: new USB bus registered, assigned bus number 1
- [ 3.771544] ehci-platform 101c0000.ehci: irq 26, io mem 0x101c0000
- [ 3.788422] ehci-platform 101c0000.ehci: USB 2.0 started, EHCI 1.00
- [ 3.801994] hub 1-0:1.0: USB hub found
- [ 3.809990] hub 1-0:1.0: 1 port detected
- [ 3.823568] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
- [ 3.837841] ohci-platform: OHCI generic platform driver
- [ 3.848666] ohci-platform 101c1000.ohci: Generic Platform OHCI controller
- [ 3.862262] ohci-platform 101c1000.ohci: new USB bus registered, assigned bus number 2
- [ 3.878194] ohci-platform 101c1000.ohci: irq 26, io mem 0x101c1000
- [ 3.915374] hub 2-0:1.0: USB hub found
- [ 3.923373] hub 2-0:1.0: 1 port detected
- [ 3.936495] kmodloader: done loading kernel modules from /etc/modules-boot.d/*
- [ 3.955358] init: - preinit -
- [ 4.080508] usb 1-1: new high-speed USB device number 2 using ehci-platform
- [ 4.668805] hub 1-1:1.0: USB hub found
- [ 4.768271] hub 1-1:1.0: 4 ports detected
- [ 4.848520] random: procd: uninitialized urandom read (4 bytes read)
- [ 5.231629] usb 1-1.2: new high-speed USB device number 3 using ehci-platform
- [ 5.251938] random: jshn: uninitialized urandom read (4 bytes read)
- [ 5.431566] random: jshn: uninitialized urandom read (4 bytes read)
- [ 5.916295] urandom_read: 4 callbacks suppressed
- [ 5.916304] random: jshn: uninitialized urandom read (4 bytes read)
- [ 6.396876] 8021q: adding VLAN 0 to HW filter on device eth0
- [ 8.040037] mount_root: jffs2 not ready yet, using temporary tmpfs overlay
- [ 8.058390] urandom-seed: Seed file not found (/etc/urandom.seed)
- [ 8.181039] procd: - early -
- [ 8.187091] procd: - watchdog -
- [ 8.847980] random: jshn: uninitialized urandom read (4 bytes read)
- [ 8.948155] procd: - watchdog -
- [ 8.955179] procd: - ubus -
- [ 9.185351] random: ubusd: uninitialized urandom read (4 bytes read)
- [ 9.221234] procd: - init -
- [ 11.701987] kmodloader: loading kernel modules from /etc/modules.d/*
- [ 11.988760] usbcore: registered new interface driver cdc_wdm
- [ 12.017931] Loading modules backported from Linux version v5.10.110-0-g3238bffaf992
- [ 12.033279] Backport generated by backports.git v5.10.110-1-0-g1fbde860
- [ 12.113347] usbcore: registered new interface driver usbserial_generic
- [ 12.126509] usbserial: USB Serial support registered for generic
- [ 12.193556] xt_time: kernel timezone is -0000
- [ 12.239731] urngd: jent-rng init failed, err: 2
- [ 12.401783] PPP generic driver version 2.4.2
- [ 12.413893] NET: Registered protocol family 24
- [ 12.426633] qmi_wwan 1-1.2:1.5: work on RawIP mode
- [ 12.437478] qmi_wwan 1-1.2:1.5: cdc-wdm0: USB WDM device
- [ 12.449206] qmi_wwan 1-1.2:1.5 wwan0: register 'qmi_wwan' at usb-101c0000.ehci-1.2, WWAN/QMI device, 7a:a8:ae:e9:6e:86
- [ 12.470905] usbcore: registered new interface driver qmi_wwan
- [ 12.627036] usbcore: registered new interface driver option
- [ 12.638338] usbserial: USB Serial support registered for GSM modem (1-port)
- [ 12.652833] option 1-1.2:1.0: GSM modem (1-port) converter detected
- [ 12.665686] usb 1-1.2: GSM modem (1-port) converter now attached to ttyUSB0
- [ 12.679853] option 1-1.2:1.1: GSM modem (1-port) converter detected
- [ 12.692748] usb 1-1.2: GSM modem (1-port) converter now attached to ttyUSB1
- [ 12.706902] option 1-1.2:1.2: GSM modem (1-port) converter detected
- [ 12.719824] usb 1-1.2: GSM modem (1-port) converter now attached to ttyUSB2
- [ 12.733958] option 1-1.2:1.3: GSM modem (1-port) converter detected
- [ 12.746833] usb 1-1.2: GSM modem (1-port) converter now attached to ttyUSB3
- [ 12.943757] rt2800_wmac 10180000.wmac: loaded eeprom from mtd device "factory"
- [ 12.958194] ieee80211 phy0: rt2x00_set_rt: Info - RT chipset 6352, rev 0500 detected
- [ 12.973669] ieee80211 phy0: rt2x00_set_rf: Info - RF chipset 7620 detected
- [ 12.987503] ieee80211 phy0: Selected rate control algorithm 'minstrel_ht'
- [ 13.031948] kmodloader: done loading kernel modules from /etc/modules.d/*
- [ 24.722303] crng init done
- [ 46.735943] jffs2_scan_eraseblock(): End of filesystem marker found at 0x0
- [ 46.779026] jffs2_build_filesystem(): unlocking the mtd device...
- [ 46.779981] done.
- [ 46.796204] jffs2_build_filesystem(): erasing all blocks after the end marker...
- [ 48.934666] 8021q: adding VLAN 0 to HW filter on device eth0
- [ 49.060777] br-lan: port 1(eth0.1) entered blocking state
- [ 49.071639] br-lan: port 1(eth0.1) entered disabled state
- [ 49.082849] device eth0.1 entered promiscuous mode
- [ 49.092455] device eth0 entered promiscuous mode
- [ 49.237050] br-lan: port 1(eth0.1) entered blocking state
- [ 49.247889] br-lan: port 1(eth0.1) entered forwarding state
- [ 49.938878] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready
- [ 293.242138] done.
- [ 293.246035] jffs2: notice: (2443) jffs2_build_xattr_subsystem: complete building xattr subsystem, 0 of xdatum (0 unchecked, 0 orphan) and 0 of xref (0 dead, 0 orphan) found.
- [ 293.495834] overlayfs: upper fs does not support tmpfile.
复制代码 |
|