找回密码
 立即注册

QQ登录

只需一步,快速开始

搜索
广告投放联系QQ68610888
查看: 1214|回复: 9

中移路由ZY-365 1200M WIFI放大器 刷openwrt 系统

[复制链接]
发表于 2023-5-30 22:07 | 显示全部楼层 |阅读模式
本帖最后由 moomin 于 2023-5-31 10:57 编辑


中移路由ZY-365 1200M WIFI放大器

192.168.10.1
cmcc-61fc-2.4g
管理员admin

TTL:

dcache: sets:256, ways:4, linesz:32 ,total:32768

##### The CPU freq = 575 MHZ ####
estimate memory size =64 Mbytes
RESET MT7628 PHY!!!!!!
Please choose the operation:
   1: Load system code to SDRAM via TFTP.
   2: Load system code then write to Flash via TFTP.
   3: Boot system code via Flash (default).
   4: Entr boot command line interface.
   7: Load Boot Loader code then write to Flash via Serial.
   9: Load Boot Loader code then write to Flash via TFTP.
   a: Load JCG firmware then write to Flash via TFTP.
0
   
3: System Boot system code via Flash.
## Booting image at bc050000 ...
   Image Name:   JCG_1200M
   Image Type:   MIPS Linux Kernel Image (lzma compressed)
   Data Size:    1175229 Bytes =  1.1 MB
   Load Address: 80000000
   Entry Point:  80000000
   Verifying Checksum ... OK
   Uncompressing Kernel Image ... OK
No initrd
## Transferring control to Linux (at address 80000000) ...
## Giving linux memsize in MB, 64

Starting kernel ...


LINUX started...

THIS IS ASIC

SDK 5.0.S.0
[    0.000000] Linux version 3.10.108 (vicky@huayi) (gcc version 4.8.3 (OpenWrt/Linaro GCC 4.8-2014.04 unknown) ) #1 Wed May 25 19:24:51 CST 2022
[    0.000000]
[    0.000000]  The CPU feqenuce set to 580 MHz
[    0.000000] CPU0 revision is: 00019655 (MIPS 24KEc)
[    0.000000] Software DMA cache coherency
[    0.000000] Determined physical RAM map:
[    0.000000]  memory: 04000000 @ 00000000 (usable)
[    0.000000] Initrd not found or empty - disabling initrd
[    0.000000] Zone ranges:
[    0.000000]   Normal   [mem 0x00000000-0x03ffffff]
[    0.000000] Movable zone start for each node
[    0.000000] Early memory node ranges
[    0.000000]   node   0: [mem 0x00000000-0x03ffffff]
[    0.000000] Primary instruction cache 64kB, 4-way, VIPT, linesize 32 bytes.
[    0.000000] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 16256
[    0.000000] Kernel command line: console=ttyS1,57600n8 root=/dev/mtdblock5 rootfstype=squashfs,jffs2 print-fatal-signals=1
[    0.000000] PID hash table entries: 256 (order: -2, 1024 bytes)
[    0.000000] Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
[    0.000000] Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
[    0.000000] Writing ErrCtl register=0007a00b
[    0.000000] Readback ErrCtl register=0007a00b
[    0.000000] Memory: 61348k/65536k available (2551k kernel code, 4140k reserved, 648k data, 192k init, 0k highmem)
[    0.000000] NR_IRQS:128
[    0.000000] console [ttyS1] enabled
[    0.096000] Calibrating delay loop... 385.02 BogoMIPS (lpj=770048)
[    0.136000] pid_max: default: 32768 minimum: 301
[    0.140000] Mount-cache hash table entries: 512
[    0.144000] NET: Registered protocol family 16
[    0.148000] RALINK_GPIOMODE = 54054404
[    0.152000] RALINK_GPIOMODE = 54044404
[    0.252000] ***** Xtal 40MHz *****
[    0.256000] start PCIe register access
[    0.756000] RALINK_RSTCTRL = 2400000
[    0.760000] RALINK_CLKCFG1 = fdbfffc0
[    0.764000]
[    0.764000] *************** MT7628 PCIe RC mode *************
[    1.264000] PCIE0 enabled
[    1.268000] Port 0 N_FTS = 1b105000
[    1.272000] init_rt2880pci done
[    1.296000] bio: create slab <bio-0> at 0
[    1.300000] PCI host bridge to bus 0000:00
[    1.304000] pci_bus 0000:00: root bus resource [mem 0x20000000-0x2fffffff]
[    1.308000] pci_bus 0000:00: root bus resource [io  0x10160000-0x1016ffff]
[    1.312000] pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff]
[    1.316000] pci 0000:00:00.0: bridge configuration invalid ([bus 00-00]), reconfiguring
[    1.320000] pci 0000:00:00.0: BAR 0: can't assign mem (size 0x80000000)
[    1.324000] pci 0000:00:00.0: BAR 8: assigned [mem 0x20000000-0x200fffff]
[    1.328000] pci 0000:00:00.0: BAR 9: assigned [mem 0x20100000-0x201fffff pref]
[    1.332000] pci 0000:00:00.0: BAR 1: assigned [mem 0x20200000-0x2020ffff]
[    1.336000] pci 0000:01:00.0: BAR 0: assigned [mem 0x20000000-0x200fffff 64bit]
[    1.340000] pci 0000:01:00.0: BAR 6: assigned [mem 0x20100000-0x2010ffff pref]
[    1.344000] pci 0000:00:00.0: PCI bridge to [bus 01]
[    1.348000] pci 0000:00:00.0:   bridge window [mem 0x20000000-0x200fffff]
[    1.352000] pci 0000:00:00.0:   bridge window [mem 0x20100000-0x201fffff pref]
[    1.356000] BAR0 at slot 0 = 0
[    1.360000] bus=0x0, slot = 0x0
[    1.364000] res[0]->start = 0
[    1.368000] res[0]->end = 0
[    1.372000] res[1]->start = 20200000
[    1.376000] res[1]->end = 2020ffff
[    1.380000] res[2]->start = 0
[    1.384000] res[2]->end = 0
[    1.388000] res[3]->start = 0
[    1.392000] res[3]->end = 0
[    1.396000] res[4]->start = 0
[    1.400000] res[4]->end = 0
[    1.404000] res[5]->start = 0
[    1.408000] res[5]->end = 0
[    1.412000] bus=0x1, slot = 0x0
[    1.416000] res[0]->start = 20000000
[    1.420000] res[0]->end = 200fffff
[    1.424000] res[1]->start = 0
[    1.428000] res[1]->end = 0
[    1.432000] res[2]->start = 0
[    1.436000] res[2]->end = 0
[    1.440000] res[3]->start = 0
[    1.444000] res[3]->end = 0
[    1.448000] res[4]->start = 0
[    1.452000] res[4]->end = 0
[    1.456000] res[5]->start = 0
[    1.460000] res[5]->end = 0
[    1.464000] Switching to clocksource MIPS
[    1.468000] NET: Registered protocol family 2
[    1.480000] TCP established hash table entries: 512 (order: 0, 4096 bytes)
[    1.492000] TCP bind hash table entries: 512 (order: -1, 2048 bytes)
[    1.504000] TCP: Hash tables configured (established 512 bind 512)
[    1.520000] TCP: reno registered
[    1.524000] UDP hash table entries: 256 (order: 0, 4096 bytes)
[    1.536000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[    1.548000] NET: Registered protocol family 1
[    1.560000] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[    1.572000] jffs2: version 2.2. (NAND) (SUMMARY)  (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[    1.592000] msgmni has been set to 119
[    1.600000] io scheduler noop registered (default)
[    1.616000] Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled
[    1.632000] serial8250: ttyS0 at MMIO 0x10000d00 (irq = 21) is a 16550A
[    1.644000] serial8250: ttyS1 at MMIO 0x10000c00 (irq = 20) is a 16550A
[    1.660000] huayi_gpio_event_init!
[    1.664000] Ralink gpio driver initialized
[    1.676000] flash manufacture id: c2, device id 20 17
[    1.684000] MX25L6405D(c2 2017c220) (8192 Kbytes)
[    1.696000] mtd .name = raspi, .size = 0x00800000 (8M) .erasesize = 0x00010000 (64K) .numeraseregions = 0
[    1.712000] Creating 5 MTD partitions on "raspi":
[    1.724000] 0x000000000000-0x000000800000 : "ALL"
[    1.732000] 0x000000000000-0x000000030000 : "Bootloader"
[    1.744000] 0x000000030000-0x000000040000 : "Config"
[    1.756000] 0x000000040000-0x000000050000 : "Factory"
[    1.768000] 0x000000050000-0x000000800000 : "firmware"
[    1.780000] 0x00000016eefd-0x000000800000 : "rootfs"
[    1.792000] mtd: partition "rootfs" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only
[    1.816000] mtd: partition "rootfs_data" created automatically, ofs=0x600000, len=0x200000
[    1.832000] 0x000000600000-0x000000800000 : "rootfs_data"
[    1.844000] GMAC1_MAC_ADRH -- : 0x0000045f
[    1.852000] GMAC1_MAC_ADRL -- : 0xa77061fb
[    1.860000] Ralink APSoC Ethernet Driver Initilization. v3.1  512 rx/tx descriptors allocated, mtu = 1500!
[    1.880000] GMAC1_MAC_ADRH -- : 0x0000045f
[    1.888000] GMAC1_MAC_ADRL -- : 0xa77061fb
[    1.900000] PROC INIT OK!
[    1.904000] huayi_port_event_init!
[    1.912000] onlineinit
[    1.916000] gre: GRE over IPv4 demultiplexor driver
[    1.924000] TCP: cubic registered
[    1.932000] NET: Registered protocol family 17
[    1.940000] Bridge firewalling registered
[    1.948000] 8021q: 802.1Q VLAN Support v1.8
[    1.960000] registered taskstats version 1
[    1.972000] VFS: Mounted root (squashfs filesystem) readonly on device 31:5.
[    1.988000] Freeing unused kernel memory: 192K
[    2.612000] init: Console is alive
[    4.636000] init: - preinit -
/etc/preinit: line 1: swconfig: not found
/etc/preinit: line 1: swconfig: not found
/etc/preinit: line 1: swconfig: not found
/etc/preinit: line 1: swconfig: not found
/etc/preinit: line 1: swconfig: not found
[    5.620000]  4:5F:FFFFFFA7:70:61:FFFFFFFB
[    5.628000] Raeth v3.1 (Tasklet,SkbRecycle)
[    5.636000]
[    5.636000] phy_tx_ring = 0x03fd6000, tx_ring = 0xa3fd6000
[    5.652000]
[    5.652000] phy_rx_ring0 = 0x03000000, rx_ring[0] = 0xa3000000
[    5.664000]
[    5.664000] phy_rx_ring0 = 0x03000000, rx_ring[0] = 0xa3000000
[    5.696000] GMAC1_MAC_ADRH -- : 0x0000045f
[    5.704000] GMAC1_MAC_ADRL -- : 0xa77061fb
[    5.712000] RT305x_ESW: Link Status Changed
Press the [f] key and hit [enter] to enter failsafe mode
Press the [1], [2], [3] or [4] key and hit [enter] to select the debug level
mount_root.
emmc_partition_find(0x4a6008, rootfs_data)
(null) is not created by block2mtd, skip.
[    9.092000] block: attempting to load /etc/config/fstab
[    9.100000] block: unable to load configuration (fstab: Entry not found)
[    9.116000] block: no usable configuration
jffs2 is ready
No jffs2 marker was found
[    9.172000] jffs2: notice: (225) jffs2_build_xattr_subsystem: complete building xattr subsystem, 42 of xdatum (1 unchecked, 41 orphan) and 49 of xref (0 dead, 41 orphan) found.
[    9.212000] block: attempting to load /etc/config/fstab
[    9.220000] block: unable to load configuration (fstab: Entry not found)
[    9.236000] block: no usable configuration
switching to overlay
[    9.264000] procd: - early -
[   10.024000] procd: - ubus -
[   11.040000] procd: - init -
Please press Enter to activate this console.
[   12.076000] huayi basic dal module init
[   12.088000] Registerd character driver
[   12.096000] huayi ctl module init!!
[   12.104000] huayi runstate module init
[   12.120000] l2tp_core: L2TP core driver, V2.0
[   12.132000] l2tp_netlink: L2TP netlink interface
[   12.144000] huayi stt module init
[   12.160000] u32 classifier
[   12.164000]     input device check on
[   12.172000]     Actions configured
[   12.184000] Mirror/redirect action on
[   12.876000]
[   12.876000]
[   12.876000] === pAd = c04fd000, size = 1472144 ===
[   12.876000]
[   12.892000] <-- RTMPAllocTxRxRingMemory, Status=0, ErrorValue=0x
[   12.908000] <-- RTMPAllocAdapterBlock, Status=0
[   12.916000] RtmpChipOpsHook(492): Not support for HIF_MT yet!
[   12.928000] mt7628_init()-->
[   12.932000] mt7628_init(FW(8a00), HW(8a01), CHIPID(7628))
[   12.944000] e2.bin mt7628_init(1135):2), pChipCap->fw_len(63888)
[   12.956000] mt_bcn_buf_init(218): Not support for HIF_MT yet!
[   12.968000] <--mt7628_init()
[   13.140000] -->mtfwd_init()<--
[   13.152000] nf_conntrack version 0.5.0 (961 buckets, 3844 max)
[   13.200000] Netfilter messages via NETLINK v0.30.
[   13.220000] Ralink APSoC Hardware Watchdog Timer
[   13.232000] rdm_major = 253
[   13.372000] xt_time: kernel timezone is -0000
[   13.396000] Ebtables v2.0 registered
[   13.404000] ip_tables: (C) 2000-2006 Netfilter Core Team
[   13.416000] Type=Linux
[   13.440000] ctnetlink v0.93: registering with nfnetlink.
[   13.460000] PPP generic driver version 2.4.2
[   13.472000] NET: Registered protocol family 24
[   13.492000] l2tp_ppp: PPPoL2TP kernel driver, V2.0
^CPlease press Enter to activate this console.
[   18.336000] led=37, on=8, off=8, blinks,=4000, reset=1, time=4000
[   18.700000] led=43, on=8, off=8, blinks,=4000, reset=1, time=4000
[   18.840000] led=42, on=8, off=8, blinks,=4000, reset=1, time=4000
[   19.088000] led=41, on=8, off=8, blinks,=4000, reset=1, time=4000
[   19.844000] ra2880stop()...Done
[   19.852000] Free TX/RX Ring Memory!
[   19.884000]  4:5F:FFFFFFA7:70:61:FFFFFFFB
[   19.892000] Raeth v3.1 (Tasklet,SkbRecycle)
[   19.900000]
[   19.900000] phy_tx_ring = 0x02988000, tx_ring = 0xa2988000
[   19.916000]
[   19.916000] phy_rx_ring0 = 0x02990000, rx_ring[0] = 0xa2990000
[   19.932000]
[   19.932000] phy_rx_ring0 = 0x02990000, rx_ring[0] = 0xa2990000
[   19.960000] GMAC1_MAC_ADRH -- : 0x0000045f
[   19.968000] GMAC1_MAC_ADRL -- : 0xa77061fb
[   19.976000] RT305x_ESW: Link Status Changed
[   19.996000] device eth0.1 entered promiscuous mode
[   20.004000] device eth0 entered promiscuous mode
[   20.040000] br-lan: port 1(eth0.1) entered forwarding state
[   20.052000] br-lan: port 1(eth0.1) entered forwarding state
[   20.168000] device eth0.2 entered promiscuous mode
[   20.176000] br-lan: port 2(eth0.2) entered forwarding state
[   20.188000] br-lan: port 2(eth0.2) entered forwarding state
[   22.056000] br-lan: port 1(eth0.1) entered forwarding state
[   22.192000] br-lan: port 2(eth0.2) entered forwarding state
vifs_down apcli0 lan
vifs_down ra0 lan
vifs_up ra0 lan
[   25.308000] TX_BCN DESC a28a7000 size = 320
[   25.316000] RX[0] DESC a28aa000 size = 1024
[   25.324000] RX[1] DESC a28ab000 size = 1024
[   25.340000] cfg_mode=9
[   25.344000] cfg_mode=9
[   25.348000] wmode_band_equal(): Band Equal!
[   25.356000] AndesSendCmdMsg: Could not send in band command due to diable fRTMP_ADAPTER_MCU_SEND_IN_BAND_CMD
[   25.380000] APSDCapable[0]=1
[   25.384000] APSDCapable[1]=1
[   25.392000] APSDCapable[2]=1
[   25.396000] APSDCapable[3]=1
[   25.404000] APSDCapable[4]=1
[   25.408000] APSDCapable[5]=1
[   25.412000] APSDCapable[6]=1
[   25.420000] APSDCapable[7]=1
[   25.424000] APSDCapable[8]=1
[   25.432000] APSDCapable[9]=1
[   25.436000] APSDCapable[10]=1
[   25.444000] APSDCapable[11]=1
[   25.448000] APSDCapable[12]=1
[   25.456000] APSDCapable[13]=1
[   25.460000] APSDCapable[14]=1
[   25.468000] APSDCapable[15]=1
[   25.472000] default ApCliAPSDCapable[0]=1
[   25.676000] Key1Str is Invalid key length(0) or Type(1)
[   25.688000] Key2Str is Invalid key length(0) or Type(1)
[   25.696000] Key3Str is Invalid key length(0) or Type(1)
[   25.708000] Key4Str is Invalid key length(0) or Type(1)
[   25.912000] 2d:ad:4e:bc:0c:9a:25:cc:3f:02:8f:15:f6:6e:8f:08:
[   25.924000] ce:71:4b:c7:b7:89:40:14:1b:c8:9a:b5:6f:36:80:91:
[   25.936000]
[   25.952000] load fw image from fw_header_image
[   25.960000] AndesMTLoadFwMethod1(2182)::pChipCap->fw_len(63888)
[   25.972000] FW Version:20151201
[   25.980000] FW Build Date:20151201183641
[   25.988000] CmdAddressLenReqret = 0)
[   25.996000] CmdFwStartReq: override = 1, address = 1048576
[   26.008000] CmdStartDLRsp: WiFI FW Download Success
[   26.020000] MtAsicDMASchedulerInit(): DMA Scheduler Mode=0(LMAC)
[   26.032000] efuse_probe: efuse = 10000002
[   26.040000] RtmpChipOpsEepromHook::e2p_type=0, inf_Type=4
[   26.048000] RtmpEepromGetDefault::e2p_dafault=2
[   26.056000] RtmpChipOpsEepromHook: E2P type(2), E2pAccessMode = 2, E2P default = 2
[   26.072000] NVM is FLASH mode
[   26.080000] 1. Phy Mode = 14
[   26.244000] Country Region from e2p = ffff
[   26.252000] tssi_1_target_pwr_g_band = 32
[   26.260000] 2. Phy Mode = 14
[   26.268000] 3. Phy Mode = 14
[   26.272000] NICInitPwrPinCfg(11): Not support for HIF_MT yet!
[   26.284000] NICInitializeAsic(651): Not support rtmp_mac_sys_reset () for HIF_MT yet!
[   26.300000] mt_mac_init()-->
[   26.304000] MtAsicInitMac()-->
[   26.312000] mt7628_init_mac_cr()-->
[   26.320000] MtAsicSetMacMaxLen(1276): Set the Max RxPktLen=1024!
[   26.332000] <--mt_mac_init()
[   26.336000]  WTBL Segment 1 info:
[   26.344000]          MemBaseAddr/FID:0x28000/0
[   26.352000]          EntrySize/Cnt:32/128
[   26.356000]  WTBL Segment 2 info:
[   26.364000]          MemBaseAddr/FID:0x40000/0
[   26.372000]          EntrySize/Cnt:64/128
[   26.376000]  WTBL Segment 3 info:
[   26.384000]          MemBaseAddr/FID:0x42000/64
[   26.392000]          EntrySize/Cnt:64/128
[   26.400000]  WTBL Segment 4 info:
[   26.404000]          MemBaseAddr/FID:0x44000/128
[   26.412000]          EntrySize/Cnt:32/128
[   26.420000] AntCfgInit(2940): Not support for HIF_MT yet!
[   26.432000] MCS Set = ff ff 00 00 01
[   26.440000] MtAsicSetChBusyStat(861): Not support for HIF_MT yet!
[   26.452000] [PMF]ap_pmf_init:: apidx=0, MFPC=0, MFPR=0, SHA256=0
[   26.464000] [PMF]RTMPMakeRsnIeCap: RSNIE Capability MFPC=0, MFPR=0
[   26.476000] MtAsicSetRalinkBurstMode(3047): Not support for HIF_MT yet!
[   26.488000] MtAsicSetPiggyBack(796): Not support for HIF_MT yet!
[   26.520000] reload DPD from flash , 0x9F = [c600] doReload bit7[0]
[   26.532000] CmdLoadDPDDataFromFlash: Channel = 6, DoReload = 0
[   26.544000] MtAsicSetTxPreamble(3026): Not support for HIF_MT yet!
[   26.556000] CmdSlotTimeSetret = 0)
[   26.568000] MtAsicAddSharedKeyEntry(1343): Not support for HIF_MT yet!
[   26.580000] MtAsicSetPreTbtt(): bss_idx=0, PreTBTT timeout = 0xf0
[   26.592000] ap_ftkd> Initialize FT KDP Module...
[   26.600000] Main bssid = 04:5f:a7:70:61:fc
[   26.608000] <==== rt28xx_init, Status=0
[   26.624000] @@@ ed_monitor_exit : ===>
[   26.632000] @@@ ed_monitor_exit : <===
[   26.640000] mt7628_set_ed_cca: TURN OFF EDCCA  mac 0x10618 = 0xd7083f0f, EDCCA_Status=0
[   26.652000] WiFi Startup Cost (ra0): 1.344s
[   26.672000] device ra0 entered promiscuous mode
[   26.680000] br-lan: port 3(ra0) entered forwarding state
[   26.692000] br-lan: port 3(ra0) entered forwarding state
[   27.744000] register rt2860
[   27.760000]
[   27.760000]
[   27.760000] === pAd = c0f01000, size = 2259296 ===
[   27.760000]
[   27.780000] <-- RTMPAllocTxRxRingMemory, Status=0
[   27.792000] <-- RTMPAllocAdapterBlock, Status=0
[   27.800000] pAd->CSRBaseAddress =0xc0e00000, csr_addr=0xc0e00000!
[   27.812000] device_id =0x7662
[   27.820000] ==>rlt_wlan_chip_onoff(): OnOff:1, Reset= 1, pAd->WlanFunCtrl:0x0, Reg-WlanFunCtrl=0x20a
[   27.836000] ====> mt76x2_ePA_per_rate_compensate_init: 5868 is_ePA: 1
[   27.852000] E2pAccessMode=2
[   27.860000] cfg_mode=14
[   27.864000] cfg_mode=14
[   27.868000] wmode_band_equal(): Band Not Equal!
[   27.884000] APSDCapable[0]=0
[   27.888000] APSDCapable[1]=0
[   27.896000] APSDCapable[2]=0
[   27.900000] APSDCapable[3]=0
[   27.908000] APSDCapable[4]=0
[   27.912000] APSDCapable[5]=0
[   27.916000] APSDCapable[6]=0
[   27.924000] APSDCapable[7]=0
[   27.928000] APSDCapable[8]=0
[   27.936000] APSDCapable[9]=0
[   27.940000] APSDCapable[10]=0
[   27.948000] APSDCapable[11]=0
[   27.952000] APSDCapable[12]=0
[   27.960000] APSDCapable[13]=0
[   27.964000] APSDCapable[14]=0
[   27.968000] APSDCapable[15]=0
[   27.976000] default ApCliAPSDCapable[0]=0
[   28.380000] Key1Str is Invalid key length(0) or Type(1)
[   28.392000] Key1Str is Invalid key length(0) or Type(1)
[   28.400000] Key2Str is Invalid key length(0) or Type(1)
[   28.412000] Key2Str is Invalid key length(0) or Type(1)
[   28.424000] Key3Str is Invalid key length(0) or Type(1)
[   28.432000] Key3Str is Invalid key length(0) or Type(1)
[   28.444000] Key4Str is Invalid key length(0) or Type(1)
[   28.456000] Key4Str is Invalid key length(0) or Type(1)
[   28.668000] 2d:ad:4e:bc:0c:9a:25:cc:3f:02:8f:15:f6:6e:8f:08:
[   28.680000] ce:71:4b:c7:b7:89:40:14:1b:c8:9a:b5:6f:36:80:91:
[   28.692000]
[   28.696000] br-lan: port 3(ra0) entered forwarding state
[   28.760000] WiFi Mcast disabled=0
[   28.764000] RtmpChipOpsEepromHook::e2p_type=2, inf_Type=5
[   28.776000] NVM is FLASH mode (pAd->flash_offset = 0x8000)
[   28.788000] get_dev_name_prefix(): dev_idx = 1, dev_name_prefix=rai
vifs_down apclii0 lan
vifs_down rai0 lan
vifs_down rai1 lan
vifs_up rai0 lan
[   29.132000] build time =
[   29.136000] 20141115060606a
[   29.144000] rom patch for E3 IC
[   29.148000]
[   29.152000] platform =
[   29.156000] ALPS
[   29.160000] hw/sw version =
[   29.164000]

                [   29.168000] patch version =
[   29.176000]
[   29.192000] FW Version:0.0.00 Build:1
[   29.196000] Build Time:201507311614____
[   29.204000] fw for E3 IC
[   29.228000] RX[0] DESC a1f14000 size = 4096
[   29.236000] RX[1] DESC a1f15000 size = 4096
[   29.256000] E2pAccessMode=2
[   29.264000] cfg_mode=14
[   29.268000] cfg_mode=14
[   29.272000] wmode_band_equal(): Band Not Equal!
[   29.288000] APSDCapable[0]=0
[   29.292000] APSDCapable[1]=0
[   29.300000] APSDCapable[2]=0
[   29.304000] APSDCapable[3]=0
[   29.308000] APSDCapable[4]=0
[   29.316000] APSDCapable[5]=0
[   29.320000] APSDCapable[6]=0
[   29.328000] APSDCapable[7]=0
[   29.332000] APSDCapable[8]=0
[   29.340000] APSDCapable[9]=0
[   29.344000] APSDCapable[10]=0
[   29.348000] APSDCapable[11]=0
[   29.356000] APSDCapable[12]=0
[   29.360000] APSDCapable[13]=0
[   29.368000] APSDCapable[14]=0
[   29.372000] APSDCapable[15]=0
[   29.380000] default ApCliAPSDCapable[0]=0
[   29.784000] Key1Str is Invalid key length(0) or Type(1)
[   29.796000] Key1Str is Invalid key length(0) or Type(1)
[   29.808000] Key2Str is Invalid key length(0) or Type(1)
[   29.816000] Key2Str is Invalid key length(0) or Type(1)
[   29.828000] Key3Str is Invalid key length(0) or Type(1)
[   29.840000] Key3Str is Invalid key length(0) or Type(1)
[   29.848000] Key4Str is Invalid key length(0) or Type(1)
[   29.860000] Key4Str is Invalid key length(0) or Type(1)
[   30.072000] 2d:ad:4e:bc:0c:9a:25:cc:3f:02:8f:15:f6:6e:8f:08:
[   30.084000] ce:71:4b:c7:b7:89:40:14:1b:c8:9a:b5:6f:36:80:91:
[   30.096000]
[   30.152000] WiFi Mcast disabled=0
[   30.156000] 1. Phy Mode = 49
[   30.164000] get_chl_grp:illegal channel (167)
[   30.172000] get_chl_grp:illegal channel (167)
[   30.180000] get_chl_grp:illegal channel (169)
[   30.188000] get_chl_grp:illegal channel (169)
[   30.200000] get_chl_grp:illegal channel (171)
[   30.208000] get_chl_grp:illegal channel (171)
[   30.216000] Country Region from e2p = ffff
[   30.224000] mt76x2_read_temp_info_from_eeprom:: is_temp_tx_alc=0, temp_tx_alc_enable=0
[   30.240000] mt76x2_read_tx_alc_info_from_eeprom:: is_ePA_mode=0, ePA_type=3
[   30.252000] mt76x2_read_tx_alc_info_from_eeprom:: [5G band] high_temp_slope=0, low_temp_slope=0
[   30.272000] mt76x2_read_tx_alc_info_from_eeprom:: [2G band] high_temp_slope=0, low_temp_slope=0
[   30.288000] mt76x2_read_tx_alc_info_from_eeprom:: [5G band] tc_lower_bound=0, tc_upper_bound=0
[   30.304000] mt76x2_read_tx_alc_info_from_eeprom:: [2G band] tc_lower_bound=0, tc_upper_bound=0
[   30.324000] mt76x2_get_external_lna_gain:NA type=0x11, BLNAGain=0x0, ALNAGain0=0x0, ALNAGain1=0x0, ALNAGain2=0x0
[   30.344000] 2. Phy Mode = 49
[   30.348000] 3. Phy Mode = 49
[   30.356000] andes_pci_fw_init
[   30.360000] 0x1300 = 00073200
[   30.392000] AntCfgInit: primary/secondary ant 0/1
[   30.400000] andes_load_cr:cr_type(2)
[   30.420000] ChipStructAssign(): MT76x2 hook !
[   30.428000] MCS Set = ff ff 00 00 01
[   30.824000] mt76x2_bbp_adjust():rf_bw=2, ext_ch=1, PrimCh=157, HT-CentCh=159, VHT-CentCh=155
[   30.940000] TX0 power compensation = 0x38
[   30.948000] TX1 power compensation = 0x38
[   30.956000] APStartUp(): AP Set CentralFreq at 155(Prim=157, HT-CentCh=159, VHT-CentCh=155, BBP_BW=2)
[   30.992000] mt76x2_calibration(channel = 155)
[   31.384000] ap_ftkd> Initialize FT KDP Module...
[   31.392000] Main bssid = 04:5f:a7:70:62:00
[   31.400000] mt76x2_reinit_agc_gainriginal agc_vga0 = 0x5c, agc_vga1 = 0x5c
[   31.416000] mt76x2_reinit_agc_gain:updated agc_vga0 = 0x5c, agc_vga1 = 0x5c
[   31.428000] mt76x2_reinit_hi_lna_gainriginal hi_lna0 = 0x27, hi_lna1 = 0x27
[   31.444000] mt76x2_reinit_hi_lna_gain:updated hi_lna0 = 0x27, hi_lna1 = 0x27
[   31.456000] original vga value(chain0) = 5c
[   31.464000] original vga value(chain1) = 5c
[   31.472000] <==== rt28xx_init, Status=0
[   31.480000] get_dev_name_prefix(): dev_idx = 1, dev_name_prefix=rai
[   31.492000] Started WatchDog Timer.
[   31.504000] get_dev_name_prefix(): dev_idx = 1, dev_name_prefix=apclii
[   31.516000] RTMPDrvOpen(1):Check if PDMA is idle!
[   31.528000] RTMPDrvOpen(2):Check if PDMA is idle!
[   31.560000] device rai0 entered promiscuous mode
[   31.568000] br-lan: port 4(rai0) entered forwarding state
[   31.580000] br-lan: port 4(rai0) entered forwarding state
vifs_up rai1 lan
[   31.672000] device rai1 entered promiscuous mode
[   31.680000] br-lan: port 5(rai1) entered forwarding state
[   31.692000] br-lan: port 5(rai1) entered forwarding state
[   33.584000] br-lan: port 4(rai0) entered forwarding state
[   33.696000] br-lan: port 5(rai1) entered forwarding state
[   79.392000] led=43, on=8, off=8, blinks,=4000, reset=1, time=4000
[   79.452000] led=42, on=8, off=8, blinks,=4000, reset=1, time=4000
[   79.516000] led=41, on=8, off=8, blinks,=4000, reset=1, time=4000
[  139.380000] led=43, on=8, off=8, blinks,=4000, reset=1, time=4000
[  139.444000] led=42, on=8, off=8, blinks,=4000, reset=1, time=4000
[  139.504000] led=41, on=8, off=8, blinks,=4000, reset=1, time=4000
[  199.392000] led=43, on=8, off=8, blinks,=4000, reset=1, time=4000
[  199.452000] led=42, on=8, off=8, blinks,=4000, reset=1, time=4000
[  199.516000] led=41, on=8, off=8, blinks,=4000, reset=1, time=4000
[  259.384000] led=43, on=8, off=8, blinks,=4000, reset=1, time=4000
[  259.444000] led=42, on=8, off=8, blinks,=4000, reset=1, time=4000
[  259.508000] led=41, on=8, off=8, blinks,=4000, reset=1, time=4000
[  319.392000] led=43, on=8, off=8, blinks,=4000, reset=1, time=4000
[  319.456000] led=42, on=8, off=8, blinks,=4000, reset=1, time=4000
[  319.516000] led=41, on=8, off=8, blinks,=4000, reset=1, time=4000
[  379.384000] led=43, on=8, off=8, blinks,=4000, reset=1, time=4000
[  379.444000] led=42, on=8, off=8, blinks,=4000, reset=1, time=4000
[  379.508000] led=41, on=8, off=8, blinks,=4000, reset=1, time=4000
[  439.384000] led=43, on=8, off=8, blinks,=4000, reset=1, time=4000
[  439.444000] led=42, on=8, off=8, blinks,=4000, reset=1, time=4000
[  439.508000] led=41, on=8, off=8, blinks,=4000, reset=1, time=4000
[  499.384000] led=43, on=8, off=8, blinks,=4000, reset=1, time=4000
[  499.444000] led=42, on=8, off=8, blinks,=4000, reset=1, time=4000
[  499.508000] led=41, on=8, off=8, blinks,=4000, reset=1, time=4000
[  559.384000] led=43, on=8, off=8, blinks,=4000, reset=1, time=4000
[  559.444000] led=42, on=8, off=8, blinks,=4000, reset=1, time=4000
[  559.508000] led=41, on=8, off=8, blinks,=4000, reset=1, time=4000
[  619.384000] led=43, on=8, off=8, blinks,=4000, reset=1, time=4000
[  619.444000] led=42, on=8, off=8, blinks,=4000, reset=1, time=4000
[  619.508000] led=41, on=8, off=8, blinks,=4000, reset=1, time=4000
[  679.384000] led=43, on=8, off=8, blinks,=4000, reset=1, time=4000
[  679.444000] led=42, on=8, off=8, blinks,=4000, reset=1, time=4000
[  679.508000] led=41, on=8, off=8, blinks,=4000, reset=1, time=4000



我的恩山、我的无线 The best wifi forum is right here.
 楼主| 发表于 2023-5-30 22:10 | 显示全部楼层
TTL :主板顺序
绿色GND
蓝色TX
紫色RX
我的恩山、我的无线 The best wifi forum is right here.
回复

使用道具 举报

 楼主| 发表于 2023-5-30 22:19 | 显示全部楼层
本帖最后由 moomin 于 2023-5-30 22:28 编辑

可能类似的路由:
360P2
JCG AC670
参考拆解链接:https://www.mydigit.cn/forum.php ... tra=page%3D1&page=1
型号:中移路由-ZY-365-
配置:
芯片 mt7612en+mt7628an
双频AC
双网口百兆---限制就在这里了,最高12MB/s 的速率



https://www.rstk.cn/news/878568.html?action=onClick

预计是 5661a
breed-mt7628-hiwifi-hc5661a.bin
2021-12-15 22:51
88K
breed-mt7628-oye-0006.bin
2021-12-15 22:51
88K

我的恩山、我的无线 The best wifi forum is right here.
回复

使用道具 举报

 楼主| 发表于 2023-5-30 23:02 | 显示全部楼层
通过原厂uboot 刷入breed成功



CPU
MediaTek MT7628AN/MT7688AN ver 1, eco 2
内存
64MB DDR2
Flash
Macronix MX25L6435E @ 47MHz (8MB)
以太网
MediaTek MT7628 built-in 5-port 10/100M switch
时钟频率
CPU: 575MHz, Bus: 191MHz, Ref: 40MHz
编译日期
2021-12-15 [git-f9b74d0]
版本
1.1 (r1337)


我的恩山、我的无线 The best wifi forum is right here.
回复

使用道具 举报

 楼主| 发表于 2023-5-30 23:02 | 显示全部楼层
对应的TTL是:

b釃剣$ぇ嗯迩鋭鍏绤剟う崮排唴匘喥拍驽鎎伷剟劋つ劊啨凚#づ鐒嚹叆舃b @噮"b绖迮噦銬牓テ`い剢E#噮嚶亮D仴b璃鄤匓腄鈫佸凞鈈沥鍰ゅ菃B參腇龄噯ヅδ嘼叅剢膰犳亜い厔囧ぇ鋮髣唶偰銬牓唴颇鎰啩剟噭偉喤bb儰叅剟鐒哪膰剟艊噯嚹呬呬呬D骲叆勄淠剣鎰剟溴囦鐒凞B叆勄淠剣鎰剟溴囦鐒凞B叆勄淠剣鎰剟溴囦鐒凞B叆勄淠剣鎰剟溴囦鐒凞B叆勄淠剣鎰剟溴囦鐒凞B叆勄淠剣鎰剟溴囦鐒凞B俠b犉囧嚖Ζデ剢剟剟妞喤や噭鏕#勀剟驿哪鏕罄釃うΔ勂唲劋勪b剟陇剝唶aB儎剟羾噭劋づ$啢b剟鈩剠唲剟b剟啶嗋驿剢剟刡噱唴ユ厔勀b嗙囦嘒#喤鎱吪勭囦嘒剠鎱囧膭勀唲剟鏕C
LINUX started...

THIS IS ASIC

SDK 5.0.S.0
[    0.000000] Linux version 3.10.108 (vicky@huayi) (gcc version 4.8.3 (OpenWrt/Linaro GCC 4.8-2014.04 unknown) ) #1 Wed May 25 19:24:51 CST 2022
[    0.000000]
[    0.000000]  The CPU feqenuce set to 580 MHz
[    0.000000] CPU0 revision is: 00019655 (MIPS 24KEc)
[    0.000000] Software DMA cache coherency
[    0.000000] Determined physical RAM map:
[    0.000000]  memory: 04000000 @ 00000000 (usable)
[    0.000000] Initrd not found or empty - disabling initrd
[    0.000000] Zone ranges:
[    0.000000]   Normal   [mem 0x00000000-0x03ffffff]
[    0.000000] Movable zone start for each node
[    0.000000] Early memory node ranges
[    0.000000]   node   0: [mem 0x00000000-0x03ffffff]
[    0.000000] Primary instruction cache 64kB, 4-way, VIPT, linesize 32 bytes.
[    0.000000] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 16256
[    0.000000] Kernel command line: console=ttyS1,57600n8 root=/dev/mtdblock5 rootfstype=squashfs,jffs2 print-fatal-signals=1
[    0.000000] PID hash table entries: 256 (order: -2, 1024 bytes)
[    0.000000] Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
[    0.000000] Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
[    0.000000] Writing ErrCtl register=00056000
[    0.000000] Readback ErrCtl register=00056000
[    0.000000] Memory: 61348k/65536k available (2551k kernel code, 4188k reserved, 648k data, 192k init, 0k highmem)
[    0.000000] NR_IRQS:128
[    0.000000] console [ttyS1] enabled
[    0.096000] Calibrating delay loop... 385.02 BogoMIPS (lpj=770048)
[    0.136000] pid_max: default: 32768 minimum: 301
[    0.140000] Mount-cache hash table entries: 512
[    0.144000] NET: Registered protocol family 16
[    0.148000] RALINK_GPIOMODE = 55154455
[    0.152000] RALINK_GPIOMODE = 55144455
[    0.252000] ***** Xtal 40MHz *****
[    0.256000] start PCIe register access
[    0.756000] RALINK_RSTCTRL = 2400000
[    0.760000] RALINK_CLKCFG1 = fdffffc0
[    0.764000]
[    0.764000] *************** MT7628 PCIe RC mode *************
[    1.264000] PCIE0 enabled
[    1.268000] Port 0 N_FTS = 1b105000
[    1.272000] init_rt2880pci done
[    1.296000] bio: create slab <bio-0> at 0
[    1.300000] PCI host bridge to bus 0000:00
[    1.304000] pci_bus 0000:00: root bus resource [mem 0x20000000-0x2fffffff]
[    1.308000] pci_bus 0000:00: root bus resource [io  0x10160000-0x1016ffff]
[    1.312000] pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff]
[    1.316000] pci 0000:00:00.0: bridge configuration invalid ([bus 00-00]), reconfiguring
[    1.320000] pci 0000:00:00.0: BAR 0: can't assign mem (size 0x80000000)
[    1.324000] pci 0000:00:00.0: BAR 8: assigned [mem 0x20000000-0x200fffff]
[    1.328000] pci 0000:00:00.0: BAR 9: assigned [mem 0x20100000-0x201fffff pref]
[    1.332000] pci 0000:00:00.0: BAR 1: assigned [mem 0x20200000-0x2020ffff]
[    1.336000] pci 0000:01:00.0: BAR 0: assigned [mem 0x20000000-0x200fffff 64bit]
[    1.340000] pci 0000:01:00.0: BAR 6: assigned [mem 0x20100000-0x2010ffff pref]
[    1.344000] pci 0000:00:00.0: PCI bridge to [bus 01]
[    1.348000] pci 0000:00:00.0:   bridge window [mem 0x20000000-0x200fffff]
[    1.352000] pci 0000:00:00.0:   bridge window [mem 0x20100000-0x201fffff pref]
[    1.356000] BAR0 at slot 0 = 0
[    1.360000] bus=0x0, slot = 0x0
[    1.364000] res[0]->start = 0
[    1.368000] res[0]->end = 0
[    1.372000] res[1]->start = 20200000
[    1.376000] res[1]->end = 2020ffff
[    1.380000] res[2]->start = 0
[    1.384000] res[2]->end = 0
[    1.388000] res[3]->start = 0
[    1.392000] res[3]->end = 0
[    1.396000] res[4]->start = 0
[    1.400000] res[4]->end = 0
[    1.404000] res[5]->start = 0
[    1.408000] res[5]->end = 0
[    1.412000] bus=0x1, slot = 0x0
[    1.416000] res[0]->start = 20000000
[    1.420000] res[0]->end = 200fffff
[    1.424000] res[1]->start = 0
[    1.428000] res[1]->end = 0
[    1.432000] res[2]->start = 0
[    1.436000] res[2]->end = 0
[    1.440000] res[3]->start = 0
[    1.444000] res[3]->end = 0
[    1.448000] res[4]->start = 0
[    1.452000] res[4]->end = 0
[    1.456000] res[5]->start = 0
[    1.460000] res[5]->end = 0
[    1.464000] Switching to clocksource MIPS
[    1.468000] NET: Registered protocol family 2
[    1.480000] TCP established hash table entries: 512 (order: 0, 4096 bytes)
[    1.492000] TCP bind hash table entries: 512 (order: -1, 2048 bytes)
[    1.504000] TCP: Hash tables configured (established 512 bind 512)
[    1.520000] TCP: reno registered
[    1.524000] UDP hash table entries: 256 (order: 0, 4096 bytes)
[    1.536000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[    1.548000] NET: Registered protocol family 1
[    1.560000] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[    1.572000] jffs2: version 2.2. (NAND) (SUMMARY)  (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[    1.592000] msgmni has been set to 119
[    1.600000] io scheduler noop registered (default)
[    1.616000] Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled
[    1.632000] serial8250: ttyS0 at MMIO 0x10000d00 (irq = 21) is a 16550A
[    1.644000] serial8250: ttyS1 at MMIO 0x10000c00 (irq = 20) is a 16550A
[    1.660000] huayi_gpio_event_init!
[    1.664000] Ralink gpio driver initialized
[    1.676000] flash manufacture id: c2, device id 20 17
[    1.684000] MX25L6405D(c2 2017c220) (8192 Kbytes)
[    1.696000] mtd .name = raspi, .size = 0x00800000 (8M) .erasesize = 0x00010000 (64K) .numeraseregions = 0
[    1.712000] Creating 5 MTD partitions on "raspi":
[    1.724000] 0x000000000000-0x000000800000 : "ALL"
[    1.732000] 0x000000000000-0x000000030000 : "Bootloader"
[    1.744000] 0x000000030000-0x000000040000 : "Config"
[    1.756000] 0x000000040000-0x000000050000 : "Factory"
[    1.768000] 0x000000050000-0x000000800000 : "firmware"
[    1.780000] 0x00000016eefd-0x000000800000 : "rootfs"
[    1.792000] mtd: partition "rootfs" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only
[    1.816000] mtd: partition "rootfs_data" created automatically, ofs=0x600000, len=0x200000
[    1.832000] 0x000000600000-0x000000800000 : "rootfs_data"
[    1.844000] GMAC1_MAC_ADRH -- : 0x0000045f
[    1.852000] GMAC1_MAC_ADRL -- : 0xa77061fb
[    1.860000] Ralink APSoC Ethernet Driver Initilization. v3.1  512 rx/tx descriptors allocated, mtu = 1500!
[    1.880000] GMAC1_MAC_ADRH -- : 0x0000045f
[    1.888000] GMAC1_MAC_ADRL -- : 0xa77061fb
[    1.900000] PROC INIT OK!
[    1.904000] huayi_port_event_init!
[    1.912000] onlineinit
[    1.916000] gre: GRE over IPv4 demultiplexor driver
[    1.924000] TCP: cubic registered
[    1.932000] NET: Registered protocol family 17
[    1.940000] Bridge firewalling registered
[    1.948000] 8021q: 802.1Q VLAN Support v1.8
[    1.960000] registered taskstats version 1
[    1.972000] VFS: Mounted root (squashfs filesystem) readonly on device 31:5.
[    1.988000] Freeing unused kernel memory: 192K
[    2.612000] init: Console is alive
[    4.636000] init: - preinit -
/etc/preinit: line 1: swconfig: not found
/etc/preinit: line 1: swconfig: not found
/etc/preinit: line 1: swconfig: not found
/etc/preinit: line 1: swconfig: not found
/etc/preinit: line 1: swconfig: not found
[    5.620000]  4:5F:FFFFFFA7:70:61:FFFFFFFB
[    5.628000] Raeth v3.1 (Tasklet,SkbRecycle)
[    5.636000]
[    5.636000] phy_tx_ring = 0x03fd6000, tx_ring = 0xa3fd6000
[    5.652000]
[    5.652000] phy_rx_ring0 = 0x03000000, rx_ring[0] = 0xa3000000
[    5.664000]
[    5.664000] phy_rx_ring0 = 0x03000000, rx_ring[0] = 0xa3000000
[    5.696000] GMAC1_MAC_ADRH -- : 0x0000045f
[    5.704000] GMAC1_MAC_ADRL -- : 0xa77061fb
[    5.712000] RT305x_ESW: Link Status Changed
Press the [f] key and hit [enter] to enter failsafe mode
Press the [1], [2], [3] or [4] key and hit [enter] to select the debug level
[    8.668000] RT305x_ESW: Link Status Changed
mount_root.
emmc_partition_find(0x4ed008, rootfs_data)
(null) is not created by block2mtd, skip.
[    9.092000] block: attempting to load /etc/config/fstab
[    9.100000] block: unable to load configuration (fstab: Entry not found)
[    9.116000] block: no usable configuration
jffs2 is ready
No jffs2 marker was found
[    9.172000] jffs2: notice: (225) jffs2_build_xattr_subsystem: complete building xattr subsystem, 42 of xdatum (1 unchecked, 41 orphan) and 49 of xref (0 dead, 41 orphan) found.
[    9.208000] block: attempting to load /etc/config/fstab
[    9.220000] block: unable to load configuration (fstab: Entry not found)
[    9.232000] block: no usable configuration
switching to overlay
[    9.264000] procd: - early -
[   10.024000] procd: - ubus -
[   11.040000] procd: - init -
Please press Enter to activate this console.
[   12.088000] huayi basic dal module init
[   12.096000] Registerd character driver
[   12.104000] huayi ctl module init!!
[   12.112000] huayi runstate module init
[   12.128000] l2tp_core: L2TP core driver, V2.0
[   12.140000] l2tp_netlink: L2TP netlink interface
[   12.152000] huayi stt module init
[   12.168000] u32 classifier
[   12.176000]     input device check on
[   12.184000]     Actions configured
[   12.192000] Mirror/redirect action on
[   12.884000]
[   12.884000]
[   12.884000] === pAd = c04fd000, size = 1472144 ===
[   12.884000]
[   12.904000] <-- RTMPAllocTxRxRingMemory, Status=0, ErrorValue=0x
[   12.916000] <-- RTMPAllocAdapterBlock, Status=0
[   12.928000] RtmpChipOpsHook(492): Not support for HIF_MT yet!
[   12.936000] mt7628_init()-->
[   12.944000] mt7628_init(FW(8a00), HW(8a01), CHIPID(7628))
[   12.956000] e2.bin mt7628_init(1135):2), pChipCap->fw_len(63888)
[   12.968000] mt_bcn_buf_init(218): Not support for HIF_MT yet!
[   12.976000] <--mt7628_init()
[   12.988000] -->mtfwd_init()<--
[   13.008000] nf_conntrack version 0.5.0 (961 buckets, 3844 max)
[   13.212000] Netfilter messages via NETLINK v0.30.
[   13.224000] Ralink APSoC Hardware Watchdog Timer
[   13.232000] rdm_major = 253
[   13.348000] xt_time: kernel timezone is -0000
[   13.408000] Ebtables v2.0 registered
[   13.420000] ip_tables: (C) 2000-2006 Netfilter Core Team
[   13.428000] Type=Linux
[   13.452000] ctnetlink v0.93: registering with nfnetlink.
[   13.476000] PPP generic driver version 2.4.2
[   13.488000] NET: Registered protocol family 24
[   13.504000] l2tp_ppp: PPPoL2TP kernel driver, V2.0
[   18.584000] led=37, on=8, off=8, blinks,=4000, reset=1, time=4000
[   18.840000] led=43, on=8, off=8, blinks,=4000, reset=1, time=4000
[   18.940000] led=42, on=8, off=8, blinks,=4000, reset=1, time=4000
[   19.260000] led=41, on=8, off=8, blinks,=4000, reset=1, time=4000
[   20.140000] ra2880stop()...Done
[   20.148000] Free TX/RX Ring Memory!
[   20.180000]  4:5F:FFFFFFA7:70:61:FFFFFFFB
[   20.188000] Raeth v3.1 (Tasklet,SkbRecycle)
[   20.196000]
[   20.196000] phy_tx_ring = 0x03fe6000, tx_ring = 0xa3fe6000
[   20.212000]
[   20.212000] phy_rx_ring0 = 0x03000000, rx_ring[0] = 0xa3000000
[   20.228000]
[   20.228000] phy_rx_ring0 = 0x03000000, rx_ring[0] = 0xa3000000
[   20.256000] GMAC1_MAC_ADRH -- : 0x0000045f
[   20.264000] GMAC1_MAC_ADRL -- : 0xa77061fb
[   20.272000] RT305x_ESW: Link Status Changed
[   20.292000] device eth0.1 entered promiscuous mode
[   20.300000] device eth0 entered promiscuous mode
[   20.384000] br-lan: port 1(eth0.1) entered forwarding state
[   20.396000] br-lan: port 1(eth0.1) entered forwarding state
[   20.484000] device eth0.2 entered promiscuous mode
[   20.492000] br-lan: port 2(eth0.2) entered forwarding state
[   20.504000] br-lan: port 2(eth0.2) entered forwarding state
[   22.400000] br-lan: port 1(eth0.1) entered forwarding state
[   22.508000] br-lan: port 2(eth0.2) entered forwarding state
[   23.196000] RT305x_ESW: Link Status Changed
[   23.812000] dev name:br-lan real:1
[   24.116000] RT305x_ESW: Link Status Changed
vifs_down apcli0 lan
vifs_down ra0 lan
vifs_up ra0 lan
[   25.560000] TX_BCN DESC a28ba000 size = 320
[   25.568000] RX[0] DESC a28bd000 size = 1024
[   25.576000] RX[1] DESC a28be000 size = 1024
[   25.592000] cfg_mode=9
[   25.596000] cfg_mode=9
[   25.600000] wmode_band_equal(): Band Equal!
[   25.608000] AndesSendCmdMsg: Could not send in band command due to diable fRTMP_ADAPTER_MCU_SEND_IN_BAND_CMD
[   25.632000] APSDCapable[0]=1
[   25.636000] APSDCapable[1]=1
[   25.644000] APSDCapable[2]=1
[   25.648000] APSDCapable[3]=1
[   25.652000] APSDCapable[4]=1
[   25.660000] APSDCapable[5]=1
[   25.664000] APSDCapable[6]=1
[   25.672000] APSDCapable[7]=1
[   25.676000] APSDCapable[8]=1
[   25.684000] APSDCapable[9]=1
[   25.688000] APSDCapable[10]=1
[   25.692000] APSDCapable[11]=1
[   25.700000] APSDCapable[12]=1
[   25.704000] APSDCapable[13]=1
[   25.712000] APSDCapable[14]=1
[   25.716000] APSDCapable[15]=1
[   25.724000] default ApCliAPSDCapable[0]=1
[   25.928000] Key1Str is Invalid key length(0) or Type(1)
[   25.940000] Key2Str is Invalid key length(0) or Type(1)
[   25.948000] Key3Str is Invalid key length(0) or Type(1)
[   25.960000] Key4Str is Invalid key length(0) or Type(1)
[   26.144000] RT305x_ESW: Link Status Changed
[   26.172000] 2d:ad:4e:bc:0c:9a:25:cc:3f:02:8f:15:f6:6e:8f:08:
[   26.184000] ce:71:4b:c7:b7:89:40:14:1b:c8:9a:b5:6f:36:80:91:
[   26.196000]
[   26.212000] load fw image from fw_header_image
[   26.220000] AndesMTLoadFwMethod1(2182)::pChipCap->fw_len(63888)
[   26.232000] FW Version:20151201
[   26.240000] FW Build Date:20151201183641
[   26.248000] CmdAddressLenReqret = 0)
[   26.256000] CmdFwStartReq: override = 1, address = 1048576
[   26.268000] CmdStartDLRsp: WiFI FW Download Success
[   26.292000] MtAsicDMASchedulerInit(): DMA Scheduler Mode=0(LMAC)
[   26.304000] efuse_probe: efuse = 10000002
[   26.312000] RtmpChipOpsEepromHook::e2p_type=0, inf_Type=4
[   26.324000] RtmpEepromGetDefault::e2p_dafault=2
[   26.332000] RtmpChipOpsEepromHook: E2P type(2), E2pAccessMode = 2, E2P default = 2
[   26.348000] NVM is FLASH mode
[   26.352000] 1. Phy Mode = 14
[   26.520000] Country Region from e2p = ffff
[   26.528000] tssi_1_target_pwr_g_band = 32
[   26.536000] 2. Phy Mode = 14
[   26.540000] 3. Phy Mode = 14
[   26.548000] NICInitPwrPinCfg(11): Not support for HIF_MT yet!
[   26.560000] NICInitializeAsic(651): Not support rtmp_mac_sys_reset () for HIF_MT yet!
[   26.576000] mt_mac_init()-->
[   26.580000] MtAsicInitMac()-->
[   26.588000] mt7628_init_mac_cr()-->
[   26.592000] MtAsicSetMacMaxLen(1276): Set the Max RxPktLen=1024!
[   26.604000] <--mt_mac_init()
[   26.612000]  WTBL Segment 1 info:
[   26.616000]          MemBaseAddr/FID:0x28000/0
[   26.624000]          EntrySize/Cnt:32/128
[   26.632000]  WTBL Segment 2 info:
[   26.640000]          MemBaseAddr/FID:0x40000/0
[   26.644000]          EntrySize/Cnt:64/128
[   26.652000]  WTBL Segment 3 info:
[   26.660000]          MemBaseAddr/FID:0x42000/64
[   26.668000]          EntrySize/Cnt:64/128
[   26.672000]  WTBL Segment 4 info:
[   26.680000]          MemBaseAddr/FID:0x44000/128
[   26.688000]          EntrySize/Cnt:32/128
[   26.696000] AntCfgInit(2940): Not support for HIF_MT yet!
[   26.704000] MCS Set = ff ff 00 00 01
[   26.712000] MtAsicSetChBusyStat(861): Not support for HIF_MT yet!
[   26.724000] [PMF]ap_pmf_init:: apidx=0, MFPC=0, MFPR=0, SHA256=0
[   26.736000] [PMF]RTMPMakeRsnIeCap: RSNIE Capability MFPC=0, MFPR=0
[   26.748000] MtAsicSetRalinkBurstMode(3047): Not support for HIF_MT yet!
[   26.764000] MtAsicSetPiggyBack(796): Not support for HIF_MT yet!
[   26.796000] reload DPD from flash , 0x9F = [c600] doReload bit7[0]
[   26.808000] CmdLoadDPDDataFromFlash: Channel = 6, DoReload = 0
[   26.820000] MtAsicSetTxPreamble(3026): Not support for HIF_MT yet!
[   26.832000] CmdSlotTimeSetret = 0)
[   26.844000] MtAsicAddSharedKeyEntry(1343): Not support for HIF_MT yet!
[   26.856000] MtAsicSetPreTbtt(): bss_idx=0, PreTBTT timeout = 0xf0
[   26.868000] ap_ftkd> Initialize FT KDP Module...
[   26.876000] Main bssid = 04:5f:a7:70:61:fc
[   26.884000] <==== rt28xx_init, Status=0
[   26.896000] @@@ ed_monitor_exit : ===>
[   26.904000] @@@ ed_monitor_exit : <===
[   26.912000] mt7628_set_ed_cca: TURN OFF EDCCA  mac 0x10618 = 0xd7083f0f, EDCCA_Status=0
[   26.928000] WiFi Startup Cost (ra0): 1.368s
[   26.944000] device ra0 entered promiscuous mode
[   26.952000] br-lan: port 3(ra0) entered forwarding state
[   26.964000] br-lan: port 3(ra0) entered forwarding state
[   28.056000] register rt2860
[   28.072000]
[   28.072000]
[   28.072000] === pAd = c0f01000, size = 2259296 ===
[   28.072000]
[   28.092000] <-- RTMPAllocTxRxRingMemory, Status=0
[   28.104000] <-- RTMPAllocAdapterBlock, Status=0
[   28.112000] pAd->CSRBaseAddress =0xc0e00000, csr_addr=0xc0e00000!
[   28.124000] device_id =0x7662
[   28.132000] ==>rlt_wlan_chip_onoff(): OnOff:1, Reset= 1, pAd->WlanFunCtrl:0x0, Reg-WlanFunCtrl=0x20a
[   28.148000] ====> mt76x2_ePA_per_rate_compensate_init: 5868 is_ePA: 1
[   28.164000] E2pAccessMode=2
[   28.172000] cfg_mode=14
[   28.176000] cfg_mode=14
[   28.180000] wmode_band_equal(): Band Not Equal!
[   28.196000] APSDCapable[0]=0
[   28.200000] APSDCapable[1]=0
[   28.208000] APSDCapable[2]=0
[   28.212000] APSDCapable[3]=0
[   28.220000] APSDCapable[4]=0
[   28.224000] APSDCapable[5]=0
[   28.232000] APSDCapable[6]=0
[   28.236000] APSDCapable[7]=0
[   28.240000] APSDCapable[8]=0
[   28.248000] APSDCapable[9]=0
[   28.252000] APSDCapable[10]=0
[   28.260000] APSDCapable[11]=0
[   28.264000] APSDCapable[12]=0
[   28.272000] APSDCapable[13]=0
[   28.276000] APSDCapable[14]=0
[   28.284000] APSDCapable[15]=0
[   28.288000] default ApCliAPSDCapable[0]=0
[   28.696000] Key1Str is Invalid key length(0) or Type(1)
[   28.704000] Key1Str is Invalid key length(0) or Type(1)
[   28.716000] Key2Str is Invalid key length(0) or Type(1)
[   28.728000] Key2Str is Invalid key length(0) or Type(1)
[   28.736000] Key3Str is Invalid key length(0) or Type(1)
[   28.748000] Key3Str is Invalid key length(0) or Type(1)
[   28.760000] Key4Str is Invalid key length(0) or Type(1)
[   28.772000] Key4Str is Invalid key length(0) or Type(1)
[   28.968000] br-lan: port 3(ra0) entered forwarding state
[   28.996000] 2d:ad:4e:bc:0c:9a:25:cc:3f:02:8f:15:f6:6e:8f:08:
[   29.004000] ce:71:4b:c7:b7:89:40:14:1b:c8:9a:b5:6f:36:80:91:
[   29.016000]
[   29.072000] WiFi Mcast disabled=0
[   29.080000] RtmpChipOpsEepromHook::e2p_type=2, inf_Type=5
[   29.092000] NVM is FLASH mode (pAd->flash_offset = 0x8000)
[   29.100000] get_dev_name_prefix(): dev_idx = 1, dev_name_prefix=rai
vifs_down apclii0 lan
vifs_down rai0 lan
vifs_down rai1 lan
vifs_up rai0 lan
[   29.456000] build time =
[   29.460000] 20141115060606a
[   29.464000] rom patch for E3 IC
[   29.472000]
[   29.476000] platform =
[   29.480000] ALPS
[   29.484000] hw/sw version =
[   29.488000]

                [   29.492000] patch version =
[   29.500000]
[   29.512000] FW Version:0.0.00 Build:1
[   29.520000] Build Time:201507311614____
[   29.528000] fw for E3 IC
[   29.548000] RX[0] DESC a1f48000 size = 4096
[   29.560000] RX[1] DESC a1f49000 size = 4096
[   29.580000] E2pAccessMode=2
[   29.584000] cfg_mode=14
[   29.592000] cfg_mode=14
[   29.596000] wmode_band_equal(): Band Not Equal!
[   29.612000] APSDCapable[0]=0
[   29.616000] APSDCapable[1]=0
[   29.620000] APSDCapable[2]=0
[   29.628000] APSDCapable[3]=0
[   29.632000] APSDCapable[4]=0
[   29.640000] APSDCapable[5]=0
[   29.644000] APSDCapable[6]=0
[   29.652000] APSDCapable[7]=0
[   29.656000] APSDCapable[8]=0
[   29.660000] APSDCapable[9]=0
[   29.668000] APSDCapable[10]=0
[   29.672000] APSDCapable[11]=0
[   29.680000] APSDCapable[12]=0
[   29.684000] APSDCapable[13]=0
[   29.692000] APSDCapable[14]=0
[   29.696000] APSDCapable[15]=0
[   29.704000] default ApCliAPSDCapable[0]=0
[   30.108000] Key1Str is Invalid key length(0) or Type(1)
[   30.120000] Key1Str is Invalid key length(0) or Type(1)
[   30.132000] Key2Str is Invalid key length(0) or Type(1)
[   30.144000] Key2Str is Invalid key length(0) or Type(1)
[   30.152000] Key3Str is Invalid key length(0) or Type(1)
[   30.164000] Key3Str is Invalid key length(0) or Type(1)
[   30.176000] Key4Str is Invalid key length(0) or Type(1)
[   30.184000] Key4Str is Invalid key length(0) or Type(1)
[   30.400000] 2d:ad:4e:bc:0c:9a:25:cc:3f:02:8f:15:f6:6e:8f:08:
[   30.408000] ce:71:4b:c7:b7:89:40:14:1b:c8:9a:b5:6f:36:80:91:
[   30.420000]
[   30.480000] WiFi Mcast disabled=0
[   30.484000] 1. Phy Mode = 49
[   30.492000] get_chl_grp:illegal channel (167)
[   30.500000] get_chl_grp:illegal channel (167)
[   30.508000] get_chl_grp:illegal channel (169)
[   30.516000] get_chl_grp:illegal channel (169)
[   30.524000] get_chl_grp:illegal channel (171)
[   30.536000] get_chl_grp:illegal channel (171)
[   30.544000] Country Region from e2p = ffff
[   30.552000] mt76x2_read_temp_info_from_eeprom:: is_temp_tx_alc=0, temp_tx_alc_enable=0
[   30.568000] mt76x2_read_tx_alc_info_from_eeprom:: is_ePA_mode=0, ePA_type=3
[   30.580000] mt76x2_read_tx_alc_info_from_eeprom:: [5G band] high_temp_slope=0, low_temp_slope=0
[   30.596000] mt76x2_read_tx_alc_info_from_eeprom:: [2G band] high_temp_slope=0, low_temp_slope=0
[   30.616000] mt76x2_read_tx_alc_info_from_eeprom:: [5G band] tc_lower_bound=0, tc_upper_bound=0
[   30.632000] mt76x2_read_tx_alc_info_from_eeprom:: [2G band] tc_lower_bound=0, tc_upper_bound=0
[   30.648000] mt76x2_get_external_lna_gain:NA type=0x11, BLNAGain=0x0, ALNAGain0=0x0, ALNAGain1=0x0, ALNAGain2=0x0
[   30.672000] 2. Phy Mode = 49
[   30.676000] 3. Phy Mode = 49
[   30.684000] andes_pci_fw_init
[   30.688000] 0x1300 = 00073200
[   30.720000] AntCfgInit: primary/secondary ant 0/1
[   30.728000] andes_load_cr:cr_type(2)
[   30.748000] ChipStructAssign(): MT76x2 hook !
[   30.756000] MCS Set = ff ff 00 00 01
[   31.156000] mt76x2_bbp_adjust():rf_bw=2, ext_ch=1, PrimCh=157, HT-CentCh=159, VHT-CentCh=155
[   31.268000] TX0 power compensation = 0x38
[   31.276000] TX1 power compensation = 0x38
[   31.284000] APStartUp(): AP Set CentralFreq at 155(Prim=157, HT-CentCh=159, VHT-CentCh=155, BBP_BW=2)
[   31.324000] mt76x2_calibration(channel = 155)
[   31.712000] ap_ftkd> Initialize FT KDP Module...
[   31.724000] Main bssid = 04:5f:a7:70:62:00
[   31.732000] mt76x2_reinit_agc_gainriginal agc_vga0 = 0x5c, agc_vga1 = 0x5c
[   31.744000] mt76x2_reinit_agc_gain:updated agc_vga0 = 0x5c, agc_vga1 = 0x5c
[   31.760000] mt76x2_reinit_hi_lna_gainriginal hi_lna0 = 0x27, hi_lna1 = 0x27
[   31.772000] mt76x2_reinit_hi_lna_gain:updated hi_lna0 = 0x27, hi_lna1 = 0x27
[   31.788000] original vga value(chain0) = 5c
[   31.796000] original vga value(chain1) = 5c
[   31.804000] <==== rt28xx_init, Status=0
[   31.812000] get_dev_name_prefix(): dev_idx = 1, dev_name_prefix=rai
[   31.828000] Started WatchDog Timer.
[   31.836000] get_dev_name_prefix(): dev_idx = 1, dev_name_prefix=apclii
[   31.848000] RTMPDrvOpen(1):Check if PDMA is idle!
[   31.860000] RTMPDrvOpen(2):Check if PDMA is idle!
[   31.900000] device rai0 entered promiscuous mode
[   31.908000] br-lan: port 4(rai0) entered forwarding state
[   31.920000] br-lan: port 4(rai0) entered forwarding state
vifs_up rai1 lan
[   32.024000] device rai1 entered promiscuous mode
[   32.032000] br-lan: port 5(rai1) entered forwarding state
[   32.044000] br-lan: port 5(rai1) entered forwarding state
[   33.924000] br-lan: port 4(rai0) entered forwarding state
[   34.048000] br-lan: port 5(rai1) entered forwarding state

点评

breed有点识别不是很好,固件可以通过字体来显示  详情 回复 发表于 2023-5-30 23:03
我的恩山、我的无线 The best wifi forum is right here.
回复

使用道具 举报

 楼主| 发表于 2023-5-30 23:03 | 显示全部楼层
moomin 发表于 2023-5-30 23:02
对应的TTL是:

b釃剣$ぇ嗯迩鋭鍏绤剟う崮排唴匘喥拍驽鎎伷剟劋つ劊啨凚#づ鐒嚹叆舃b @噮"b ...

breed有点识别不是很好,固件可以通过字体来显示
我的恩山、我的无线 The best wifi forum is right here.
回复

使用道具 举报

 楼主| 发表于 2023-5-30 23:14 | 显示全部楼层
本帖最后由 moomin 于 2023-5-30 23:19 编辑

刷这个固件试试:
https://firmware-selector.openwr ... id=hilink_hlk-7628n


刷完成后成功进入系统:

StatusSystem
Hostname
OpenWrt
Model
HILINK HLK-7628N
Architecture
MediaTek MT7628AN ver:1 eco:2
Target Platform
ramips/mt76x8
Firmware Version
OpenWrt 22.03.5 r20134-5f15225c1e / LuCI openwrt-22.03 branch git-23.093.57104-ce20b4a
Kernel Version
5.10.176
Local Time
2023-04-27 20:31:09
Uptime
0h 3m 8s
Load Average
0.51, 0.45, 0.19


Memory
Total Available


Used


Cached




Storage
Disk space


Temp space




Network
Active Connections




Active DHCP Leases



本帖子中包含更多资源

您需要 登录 才可以下载或查看,没有账号?立即注册

×
我的恩山、我的无线 The best wifi forum is right here.
回复

使用道具 举报

 楼主| 发表于 2023-5-31 10:58 | 显示全部楼层
刷完breed后波特率从56700变成115200了,不然ttl就乱码了。
我的恩山、我的无线 The best wifi forum is right here.
回复

使用道具 举报

发表于 2023-5-31 17:44 | 显示全部楼层
这个和360p2路由器的配置基本一样,360内存好像是128M,网口多几个,我直接用ASUS-rt1200文件可适配,前几天编译了openwrt,你可以试一下,breed下直接刷入。波特率我忘了,好像是我改成115200了,你试试吧。360p2可完美启动。
链接:https://pan.baidu.com/s/1-H1AwznUOhxiGyKFbuG4bQ?pwd=rjsp
提取码:rjsp

点评

可以写个编译的教程吗?有个小白朋友想要试试自己编译。  详情 回复 发表于 2023-5-31 20:10
我的恩山、我的无线 The best wifi forum is right here.
回复

使用道具 举报

 楼主| 发表于 2023-5-31 20:10 | 显示全部楼层
6548885@qq.com 发表于 2023-5-31 17:44
这个和360p2路由器的配置基本一样,360内存好像是128M,网口多几个,我直接用ASUS-rt1200文件可适配,前几 ...

可以写个编译的教程吗?有个小白朋友想要试试自己编译。
我的恩山、我的无线 The best wifi forum is right here.
回复

使用道具 举报

您需要登录后才可以回帖 登录 | 立即注册

本版积分规则

有疑问请添加管理员QQ86788181|手机版|小黑屋|Archiver|恩山无线论坛(常州市恩山计算机开发有限公司版权所有) ( 苏ICP备05084872号 )

GMT+8, 2024-3-29 08:10

Powered by Discuz! X3.5

© 2001-2024 Discuz! Team.

| 江苏省互联网有害信息举报中心 举报信箱:js12377 | @jischina.com.cn 举报电话:025-88802724 本站不良内容举报信箱:68610888@qq.com 举报电话:0519-86695797

快速回复 返回顶部 返回列表