找回密码
 立即注册

QQ登录

只需一步,快速开始

搜索
广告投放联系QQ68610888广告投放联系QQ68610888
查看: 439|回复: 12

[弱电箱路由器] 请大佬帮忙看看,一款mt6721的弱电箱路由,刷breed后固件无法启动?

[复制链接]
发表于 2024-12-6 19:45 | 显示全部楼层 |阅读模式
本帖最后由 myxieyuyan 于 2024-12-6 22:23 编辑


原路由的uboot


刷的breed

breed可以刷入也可以刷入原路由一样的固件,但是无法启动固件,启动后直接就到了breed。是否breed需要设置启动地址,下面附上原路由ssh登录进去的信息,如果有懂的大佬是否可以指点一下谢谢。

sh: /usr/bin/xauth: not found


BusyBox v1.24.1 (2019-01-02 08:01:49 UTC) built-in shell (ash)


  _______________________________________________________________
|    ____                 _                 ____               |
|   |  _ \ __ _ _ __   __| | ___  _ __ __ _| __ )  _____  __   |
|   | |_) / _` | '_ \ / _` |/ _ \| '__/ _` |  _ \ / _ \ \/ /   |
|   |  __/ (_| | | | | (_| | (_) | | | (_| | |_) | (_) >  <    |
|   |_|   \__,_|_| |_|\__,_|\___/|_|  \__,_|____/ \___/_/\_\   |
|                                                              |
|                  PandoraBox SDK Platform                     |
|                  The Core of SmartRouter                     |
|            Copyright 2013-2019 PandoraBox-Team               |
|                http://www.pandorabox.com.cn                  |
|______________________________________________________________|
  Base on LEDE/OpenWrt (19.01, r4695, 2019-01-01-git-3e8866933)
[root@PandoraBox:/root]#cat /proc/mtd
dev:    size   erasesize  name
mtd0: 00030000 00010000 "u-boot"
mtd1: 00010000 00010000 "u-boot-env"
mtd2: 00010000 00010000 "Factory"
mtd3: 01000000 00010000 "fullflash"
mtd4: 00fb0000 00010000 "firmware"
mtd5: 00186564 00010000 "kernel"
mtd6: 00e09a9c 00010000 "rootfs"
mtd7: 00880000 00010000 "rootfs_data"
mtd8: 00020000 00010000 "panic_oops"
[root@PandoraBox:/root]#dmesg
[    0.000000] Initializing cgroup subsys cpuset
[    0.000000] Initializing cgroup subsys cpu
[    0.000000] Initializing cgroup subsys cpuacct
[    0.000000] Linux version 3.14.79 (jenkins@jenkins) (gcc version 5.5.0 (PandoraBox GCC 5.5.0 2019-01-01-git-3e8866933) ) #0 SMP Tue Jan 1 11:42:58 2019
[    0.000000] MT7621: MPLL enabled.
[    0.000000] PandoraBox CPUID Module for Ralink/MTK SoC v1.1.
[    0.000000] MediaTek MT7621 pkg:BGA rev:1 eco:3 CPU:880MHz Bus:220MHz Uart:50MHz
[    0.000000] CPU running in Little Endian
[    0.000000] Board VLANLLLW
[    0.000000] Flash:SPI 3byte Size: 16MB
[    0.000000] DRAM: 256MB DDR3 16 bits
[    0.000000] Kernel Support [PCI] [USB]
[    0.000000] prom memory:256MB
[    0.000000] MT7621:ECO(0103) has PCIe reset BUG!!!
[    0.000000] MT7621: PCIe host/device reset
[    0.000000] GCMP present
[    0.000000] bootconsole [early0] enabled
[    0.000000] CPU0 revision is: 0001992f (MIPS 1004Kc)
[    0.000000] Software DMA cache coherency
[    0.000000] Determined physical RAM map:
[    0.000000]  memory: 10000000 @ 00000000 (usable)
[    0.000000] Zone ranges:
[    0.000000]   Normal   [mem 0x00000000-0x0fffffff]
[    0.000000] Movable zone start for each node
[    0.000000] Early memory node ranges
[    0.000000]   node   0: [mem 0x00000000-0x0fffffff]
[    0.000000] On node 0 totalpages: 65536
[    0.000000] free_area_init_node: node 0, pgdat 80483ec0, node_mem_map 81000000
[    0.000000]   Normal zone: 512 pages used for memmap
[    0.000000]   Normal zone: 0 pages reserved
[    0.000000]   Normal zone: 65536 pages, LIFO batch:15
[    0.000000] Detected 3 available secondary CPU(s)
[    0.000000] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes.
[    0.000000] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
[    0.000000] MIPS secondary cache 256kB, 8-way, linesize 32 bytes.
[    0.000000] PERCPU: Embedded 7 pages/cpu @81203000 s5984 r8192 d14496 u32768
[    0.000000] pcpu-alloc: s5984 r8192 d14496 u32768 alloc=8*4096
[    0.000000] pcpu-alloc: [0] 0 [0] 1 [0] 2 [0] 3
[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 65024
[    0.000000] Kernel command line: pause_on_oops=10 noresume  board=MAC2600R  console=ttyS1,115200 rootfstype=squashfs,jffs2
[    0.000000] PID hash table entries: 1024 (order: 0, 4096 bytes)
[    0.000000] Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
[    0.000000] Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
[    0.000000] Writing ErrCtl register=00008008
[    0.000000] Readback ErrCtl register=00008008
[    0.000000] allocated 524288 bytes of page_cgroup
[    0.000000] please try 'cgroup_disable=memory' option if you don't want memory cgroups
[    0.000000] Memory: 253924K/262144K available (3739K kernel code, 225K rwdata, 808K rodata, 204K init, 306K bss, 8220K reserved)
[    0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=4, Nodes=1
[    0.000000] Hierarchical RCU implementation.
[    0.000000] NR_IRQS:256
[    0.000000] GIC: Revision 3.0
[    0.000000] Setup MT7621 IRQs...Done
[    0.000000] console [ttyS1] enabled
[    0.004000] bootconsole [early0] disabled
[    0.008000] Calibrating delay loop... 574.46 BogoMIPS (lpj=1148928)
[    0.036000] pid_max: default: 32768 minimum: 301
[    0.040000] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
[    0.044000] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
[    0.048000] Initializing cgroup subsys memory
[    0.052000] Initializing cgroup subsys devices
[    0.056000] Initializing cgroup subsys freezer
[    0.060000] Initializing cgroup subsys net_cls
[    0.064000] Initializing cgroup subsys blkio
[    0.068000] Initializing cgroup subsys perf_event
[    0.072000] Initializing cgroup subsys net_prio
[    0.076000] CPU1 :Booting up...done!
[    0.080000] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes.
[    0.080000] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
[    0.080000] MIPS secondary cache 256kB, 8-way, linesize 32 bytes.
[    0.080000] CPU1 revision is: 0001992f (MIPS 1004Kc)
[    0.112000] Synchronize counters for CPU 1: done.
[    0.116000] CPU2 :Booting up...done!
[    0.120000] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes.
[    0.120000] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
[    0.120000] MIPS secondary cache 256kB, 8-way, linesize 32 bytes.
[    0.120000] CPU2 revision is: 0001992f (MIPS 1004Kc)
[    0.152000] Synchronize counters for CPU 2: done.
[    0.156000] CPU3 :Booting up...done!
[    0.160000] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes.
[    0.160000] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
[    0.160000] MIPS secondary cache 256kB, 8-way, linesize 32 bytes.
[    0.160000] CPU3 revision is: 0001992f (MIPS 1004Kc)
[    0.188000] Synchronize counters for CPU 3: done.
[    0.192000] Brought up 4 CPUs
[    0.196000] pinctrl core: initialized pinctrl subsystem
[    0.200000] NET: Registered protocol family 16
[    0.204000] Ralink/MTK BootROM maped.
[    0.208000] Ralink/MTK device hooks driver. (C) 2017 PandoraBox Team
[    0.212000] Generic Ralink/MTK Register Operation API (c) 2013-2015 PandoraBox Team
[    0.216000] SYSCTL maped at address:0xbe000000
[    0.220000] MEMCTRL maped at address:0xbe005000
[    0.224000] RFCTRL maped at address:0xbe180000
[    0.228000] Generic GPIO Driver for MediaTek MT7621 Board. (C) 2013-2015 PandoraBox Team
[    0.232000] MT7621-GPIO0:registering 32 irq handlers
[    0.236000] MT7621-GPIO1:registering 32 irq handlers
[    0.240000] MT7621-GPIO3:registering 32 irq handlers
[    0.244000] MIPS: machine is Mercury MAC2600R
[    0.248000] ralink_register_flash:SPI Flash.
[    0.252000] Ralink/MTK PinCtrl registered.
[    0.264000] MT7621CIe device GPIO reset
[    0.660000] MT7621 PCIe PHY initialize
[    1.784000] PCIE0 no card, disable it(RST&CLK)
[    1.788000] PCIE1 no card, disable it(RST&CLK)
[    1.792000] PCIE2 no card, disable it(RST&CLK)
[    1.796000] FPU Affinity set after 4664 emulations
[    1.808000] bio: create slab <bio-0> at 0
[    1.816000] Generic PinCtrl Driver for MediaTek MT7621 Board. (C) 2013-2015 PandoraBox Team
[    1.820000] PINCTRL:add 31 pins for MT7621-PINCTRL0.
[    1.824000] PINCTRL:add 31 pins for MT7621-PINCTRL1.
[    1.828000] PINCTRL:add 31 pins for MT7621-PINCTRL2.
[    1.832000] GPIO_MODE_REG:0x485AD
[    1.832000] Switched to clocksource Ralink/MTK 50kHz Systick timer
[    1.836000] PandoraBox SPLICE initialized. rcv 8fdd0000 (sz:768) kvec 8fd98000 (sz:256) per 4 core
[    1.848000] NET: Registered protocol family 2
[    1.856000] TCP established hash table entries: 2048 (order: 1, 8192 bytes)
[    1.860000] TCP bind hash table entries: 2048 (order: 2, 16384 bytes)
[    1.868000] TCP: Hash tables configured (established 2048 bind 2048)
[    1.876000] TCP: reno registered
[    1.876000] UDP hash table entries: 256 (order: 1, 8192 bytes)
[    1.884000] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes)
[    1.892000] NET: Registered protocol family 1
[    1.896000] PCI: CLS 0 bytes, default 32
[    1.896000] Ralink SoC clocks api init.
[    1.900000] mips hpt frequency:440000000HZ
[    1.996000] 4 CPUs re-calibrate udelay(lpj = 1163264)
[    2.000000] Ralink/MTK APSoC GPIO Resource maped.
[    2.004000] Load Kernel WDG Timer Module
[    2.008000] Load Ralink Timer0 Module
[    2.012000] Load Ralink Timer2 Module
[    2.016000] xHCI host registered
[    2.024000] futex hash table entries: 1024 (order: 3, 32768 bytes)
[    2.044000] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[    2.052000] jffs2: version 2.2 (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[    2.060000] msgmni has been set to 495
[    2.068000] io scheduler noop registered (default)
[    2.072000] io scheduler deadline registered
[    2.076000] io scheduler c购物 registered
[    2.080000] io scheduler b购物 registered
[    2.084000] B购物 I/O-scheduler: v7r8
[    2.088000] Serial: 8250/16550 driver, 3 ports, IRQ sharing disabled
[    2.096000] serial8250: ttyS0 at MMIO 0x1e000d00 (irq = 27, base_baud = 3125000) is a 16550A
[    2.104000] serial8250: ttyS1 at MMIO 0x1e000c00 (irq = 26, base_baud = 3125000) is a 16550A
[    2.112000] serial8250: ttyS2 at MMIO 0x1e000e00 (irq = 28, base_baud = 3125000) is a 16550A
[    2.120000] Ralink GDMA IP REV:3 IRQ:13
[    2.140000] brd: module loaded
[    2.144000] PandoraBox MT7621/28 SPI flash driver, SPI_ClK: 31MHz
[    2.152000] device id : ef 40 18 0 0 (40180000)
[    2.156000] SPI flash chip: W25Q128FV (ef 40180000) (16384 Kbytes)
[    2.164000] Creating 5 MTD partitions on "raspi":
[    2.168000] 0x000000000000-0x000000030000 : "u-boot"
[    2.176000] 0x000000030000-0x000000040000 : "u-boot-env"
[    2.180000] 0x000000040000-0x000000050000 : "Factory"
[    2.188000] 0x000000000000-0x000001000000 : "fullflash"
[    2.196000] 0x000000050000-0x000002000000 : "firmware"
[    2.200000] mtd: partition "firmware" extends beyond the end of device "raspi" -- size truncated to 0xfb0000
[    2.232000] 3 uimage-fw partitions found on MTD device firmware
[    2.240000] 0x000000050000-0x0000001d6564 : "kernel"
[    2.244000] mtd: partition "kernel" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only
[    2.260000] 0x0000001d6564-0x000000fe0000 : "rootfs"
[    2.264000] mtd: partition "rootfs" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only
[    2.276000] mtd: device 6 (rootfs) set to be root filesystem
[    2.284000] 1 squashfs-split partitions found on MTD device rootfs
[    2.288000] 0x000000760000-0x000000fe0000 : "rootfs_data"
[    2.296000] 0x000000fe0000-0x000001000000 : "panic_oops"
[    2.304000] mtdoops: ready 0, 1 (no erase)
[    2.304000] mtdoops: Attached to MTD device 8
[    2.308000] rdm_major = 250
[    2.312000] EEPROM:Read from [Factory] offset 0xe000,length 0x6.
[    2.324000] Ralink APSoC Ethernet Driver v3.2.4 (raeth)
[    2.328000] raeth: PDMA RX ring 512, QDMA TX pool 1024. Max packet size 1536
[    2.336000] raeth: NAPI & GRO support, weight 64
[    2.340000] raeth: Byte Queue Limits (BQL) support
[    2.344000] raeth: GMAC reset
[    2.352000] mt762x-gsw switch driver registered
[    2.356000] mt762x-gsw default vlans:wllll
[    2.368000] TCP: cubic registered
[    2.372000] NET: Registered protocol family 10
[    2.376000] NET: Registered protocol family 17
[    2.380000] Bridge firewalling registered
[    2.384000] 8021q: 802.1Q VLAN Support v1.8
[    2.388000] PandoraBox Mass Storage accelerater v1.2
[    2.396000] Generic NVRAM Driver for MediaTek Board. (c) 2013-2015 PandoraBox Team.
[    2.404000] NVRAM driver (major 248) installed
[    2.408000] registered taskstats version 1
[    2.416000] UBIFS error (pid 1): ubifs_mount: cannot open "ubi0:rootfs", error -19
[    2.428000] VFS: Mounted root (squashfs filesystem) readonly on device 31:6.
[    2.436000] Freeing unused kernel memory: 204K (804ad000 - 804e0000)
[    3.172000] init: Console is alive
[    3.896000] random: nonblocking pool is initialized
[    4.976000] usbcore: registered new interface driver usbfs
[    4.984000] usbcore: registered new interface driver hub
[    4.988000] usbcore: registered new device driver usb
[    4.996000] PandoraBox Button Driver init
[    5.000000] Button [reset] mapped to GPIO8 and IRQ64
[    5.032000] init: - preinit -
[    9.360000] raeth: HW IP/TCP/UDP checksum RX/TX offload enabled
[    9.368000] raeth: HW Scatter/Gather TX offload enabled
[    9.372000] raeth: HW TCP segmentation offload (TSO) enabled
[    9.376000] raeth: NAPI mode enabled
[    9.380000] raeth: NAPI GRO offload enabled
[    9.384000] raeth: Frame Engine reset
[    9.392000] raeth: QDMA init
[    9.392000] raeth: MT7530 GSW initializing
[   11.136000] raeth: port 2 link up (10Mbps/Full duplex)
[   12.176000] raeth: port 1 link up (1000Mbps/Full duplex)
[   12.396000] raeth: port 4 link up (1000Mbps/Full duplex)
[   12.600000] mount_root: loading kmods from internal overlay
[   13.588000] jffs2: notice: (442) jffs2_build_xattr_subsystem: complete building xattr subsystem, 26 of xdatum (0 unchecked, 26 orphan) and 26 of xref (0 dead, 26 orphan) found.
[   13.604000] block: attempting to load /tmp/jffs_cfg/upper/etc/config/fstab
[   13.612000] block: unable to load configuration (fstab: Entry not found)
[   13.620000] block: attempting to load /tmp/jffs_cfg/etc/config/fstab
[   13.628000] block: extroot: not configured
[   13.692000] jffs2: notice: (439) jffs2_build_xattr_subsystem: complete building xattr subsystem, 26 of xdatum (0 unchecked, 26 orphan) and 26 of xref (0 dead, 26 orphan) found.
[   14.388000] block: attempting to load /tmp/jffs_cfg/upper/etc/config/fstab
[   14.392000] block: unable to load configuration (fstab: Entry not found)
[   14.400000] block: attempting to load /tmp/jffs_cfg/etc/config/fstab
[   14.408000] block: extroot: not configured
[   14.428000] mount_root: switching to jffs2 overlay
[   14.480000] urandom-seed: Seed file not found (/etc/urandom.seed)
[   14.552000] raeth: port 1 link down
[   14.556000] raeth: port 2 link down
[   14.560000] raeth: port 4 link down
[   15.676000] NET: Registered protocol family 8
[   15.680000] NET: Registered protocol family 20
[   15.704000] loop: module loaded
[   15.712000] l2tp_core: L2TP core driver, V2.0
[   15.720000] l2tp_netlink: L2TP netlink interface
[   15.732000] gre: GRE over IPv4 demultiplexor driver
[   15.736000] ip_gre: GRE over IPv4 tunneling driver
[   15.752000] gpiodev: gpio device registered with major 247
[   15.760000] PPP generic driver version 2.4.2
[   15.772000] ip6_tables: (C) 2000-2006 Netfilter Core Team
[   15.800000] nf_conntrack version 0.5.0 (3970 buckets, 15880 max)
[   16.036000] Netfilter messages via NETLINK v0.30.
[   16.044000] ip_set: protocol 6
[   17.724000] i2c /dev entries driver
[   18.272000] u32 classifier
[   18.276000]     input device check on
[   18.280000]     Actions configured
[   18.456000] Mirror/redirect action on
[   19.960000] PandoraBox IP Bandwidth load.
[   20.364000] mt7615: module license 'Proprietary' taints kernel.
[   20.368000] Disabling lock debugging due to kernel taint
[   20.472000] register mt_drv
[   20.556000] ip_tables: (C) 2000-2006 Netfilter Core Team, NAT Type:Symmetric Cone
[   20.600000] ctnetlink v0.93: registering with nfnetlink.
[   20.700000] PPP MPPE Compression module registered
[   20.708000] NET: Registered protocol family 24
[   20.712000] p p t p driver version 0.8.5
[   20.776000] xt_time: kernel timezone is -0000
[   20.788000] l2tp_ppp: PPPoL2TP kernel driver, V2.0
[   24.580000] raeth: HW IP/TCP/UDP checksum RX/TX offload enabled
[   24.588000] raeth: HW Scatter/Gather TX offload enabled
[   24.592000] raeth: HW TCP segmentation offload (TSO) enabled
[   24.600000] raeth: NAPI mode enabled
[   24.600000] raeth: NAPI GRO offload enabled
[   24.608000] raeth: Frame Engine reset
[   24.612000] raeth: QDMA init
[   24.616000] raeth: MT7530 GSW initializing
[   24.628000] device eth0 entered promiscuous mode
[   24.636000] device eth0.1 entered promiscuous mode
[   24.644000] br-lan: port 1(eth0.1) entered forwarding state
[   24.648000] br-lan: port 1(eth0.1) entered forwarding state
[   25.372000] SFE:Connection manager init
[   26.272000] raeth: port 2 link up (10Mbps/Full duplex)
[   26.652000] br-lan: port 1(eth0.1) entered forwarding state
[   27.508000] raeth: port 1 link up (1000Mbps/Full duplex)
[   27.828000] raeth: port 4 link up (1000Mbps/Full duplex)
[   32.096000] raeth: port 0 link up (100Mbps/Full duplex)
[  104.408000] nf_conntrack: automatic helper assignment is deprecated and it will be removed soon. Use the iptables CT target to attach helpers instead.
[109565.708000] nf_conntrack: table full, dropping packet
[109582.072000] nf_conntrack: table full, dropping packet
[109582.316000] nf_conntrack: table full, dropping packet
[1069310.984000] nf_conntrack: table full, dropping packet
[1069315.736000] nf_conntrack: table full, dropping packet
[1503587.072000] raeth: port 0 link down
[1503627.448000] raeth: port 0 link up (100Mbps/Full duplex)
[1507288.440000] icmp6_send: no reply to icmp error
[1507288.444000] icmp6_send: no reply to icmp error
[1528514.504000] icmp6_send: no reply to icmp error
[1534578.716000] icmp6_send: no reply to icmp error
[1534578.724000] icmp6_send: no reply to icmp error
[1534579.136000] icmp6_send: no reply to icmp error
[1534579.140000] icmp6_send: no reply to icmp error
[1540642.952000] icmp6_send: no reply to icmp error
[1540642.956000] icmp6_send: no reply to icmp error
[1543675.072000] icmp6_send: no reply to icmp error
[1543675.080000] icmp6_send: no reply to icmp error
[1554126.816000] icmp6_send: no reply to icmp error
[1555803.636000] icmp6_send: no reply to icmp error
[1555803.644000] icmp6_send: no reply to icmp error
[1555803.648000] icmp6_send: no reply to icmp error
[1555805.232000] icmp6_send: no reply to icmp error
[1561869.252000] icmp6_send: no reply to icmp error
[1561869.256000] icmp6_send: no reply to icmp error
[1570965.364000] icmp6_send: no reply to icmp error
[1570965.368000] icmp6_send: no reply to icmp error
[1577030.988000] icmp6_send: no reply to icmp error
[1577030.992000] icmp6_send: no reply to icmp error
[1577031.920000] icmp6_send: no reply to icmp error
[1583097.104000] icmp6_send: no reply to icmp error
[1586130.416000] icmp6_send: no reply to icmp error
[1586130.420000] icmp6_send: no reply to icmp error
[1587967.412000] nf_conntrack: table full, dropping packet
[1587967.448000] nf_conntrack: table full, dropping packet
[1587967.584000] nf_conntrack: table full, dropping packet
[1587967.632000] nf_conntrack: table full, dropping packet
[1592194.384000] icmp6_send: no reply to icmp error
[1592194.388000] icmp6_send: no reply to icmp error
[1592194.396000] icmp6_send: no reply to icmp error
[2112437.076000] icmp6_send: no reply to icmp error
[2112459.624000] icmp6_send: no reply to icmp error
[2147094.356000] icmp6_send: no reply to icmp error
[2147117.800000] icmp6_send: no reply to icmp error
[2147218.132000] icmp6_send: no reply to icmp error
[2147273.140000] icmp6_send: no reply to icmp error
[2147298.160000] icmp6_send: no reply to icmp error
[2150293.888000] icmp6_send: no reply to icmp error
[2150318.420000] icmp6_send: no reply to icmp error
[2164314.052000] icmp6_send: no reply to icmp error
[2164350.596000] br-lan: received packet on eth0.1 with own address as source address
[2164463.692000] icmp6_send: no reply to icmp error
[2164551.748000] icmp6_send: no reply to icmp error
[2164551.752000] icmp6_send: no reply to icmp error
[2164893.740000] icmp6_send: no reply to icmp error
[2164914.136000] icmp6_send: no reply to icmp error
[2165062.876000] icmp6_send: no reply to icmp error
[2165062.880000] icmp6_send: no reply to icmp error
[2165116.756000] icmp6_send: no reply to icmp error
[2165319.544000] icmp6_send: no reply to icmp error
[2165559.964000] icmp6_send: no reply to icmp error
[2165699.372000] icmp6_send: no reply to icmp error
[2165709.332000] icmp6_send: no reply to icmp error
[2165719.104000] icmp6_send: no reply to icmp error
[2165731.740000] icmp6_send: no reply to icmp error
[2165731.744000] icmp6_send: no reply to icmp error
[2165731.748000] icmp6_send: no reply to icmp error
[2165731.752000] icmp6_send: no reply to icmp error
[2165740.904000] icmp6_send: no reply to icmp error
[2165779.964000] icmp6_send: no reply to icmp error
[2165788.540000] icmp6_send: no reply to icmp error
[2165814.760000] icmp6_send: no reply to icmp error
[2165814.768000] icmp6_send: no reply to icmp error
[2165817.760000] icmp6_send: no reply to icmp error
[2165817.764000] icmp6_send: no reply to icmp error
[2165817.772000] icmp6_send: no reply to icmp error
[2165817.776000] icmp6_send: no reply to icmp error
[2165817.780000] icmp6_send: no reply to icmp error
[2165817.784000] icmp6_send: no reply to icmp error
[2165817.788000] icmp6_send: no reply to icmp error
[2165821.292000] net_ratelimit: 1 callbacks suppressed
[2165821.296000] icmp6_send: no reply to icmp error
[2165821.300000] icmp6_send: no reply to icmp error
[2168792.276000] icmp6_send: no reply to icmp error
[2168792.280000] icmp6_send: no reply to icmp error
[2168797.460000] icmp6_send: no reply to icmp error
[2168810.576000] icmp6_send: no reply to icmp error
[2174871.584000] icmp6_send: no reply to icmp error
[2174888.844000] icmp6_send: no reply to icmp error
[2174921.900000] icmp6_send: no reply to icmp error
[2185515.744000] icmp6_send: no reply to icmp error
[2185550.580000] icmp6_send: no reply to icmp error
[root@PandoraBox:/root]#


本帖子中包含更多资源

您需要 登录 才可以下载或查看,没有账号?立即注册

×
只谈技术、莫论政事!(点击见详情) | 恩山无线论坛欢迎您的来访,请互相尊重、友善交流,建议保持一颗平常心看待网友的评论,切勿过度反应。
发表于 2024-12-6 20:23 来自手机 | 显示全部楼层
闪存布局那里切换下试试

点评

闪存布局几种都试了,都无法启动  详情 回复 发表于 2024-12-6 22:38
只谈技术、莫论政事!(点击见详情) | 恩山无线论坛欢迎您的来访,请互相尊重、友善交流,建议保持一颗平常心看待网友的评论,切勿过度反应。
回复 支持 反对

使用道具 举报

 楼主| 发表于 2024-12-6 22:38 | 显示全部楼层
badcrazy 发表于 2024-12-6 20:23
闪存布局那里切换下试试

闪存布局几种都试了,都无法启动

点评

换breed,  详情 回复 发表于 2024-12-10 21:24
只谈技术、莫论政事!(点击见详情) | 恩山无线论坛欢迎您的来访,请互相尊重、友善交流,建议保持一颗平常心看待网友的评论,切勿过度反应。
回复 支持 反对

使用道具 举报

发表于 2024-12-10 21:24 | 显示全部楼层
myxieyuyan 发表于 2024-12-6 22:38
闪存布局几种都试了,都无法启动

换breed,
只谈技术、莫论政事!(点击见详情) | 恩山无线论坛欢迎您的来访,请互相尊重、友善交流,建议保持一颗平常心看待网友的评论,切勿过度反应。
回复 支持 反对

使用道具 举报

发表于 2024-12-10 21:26 | 显示全部楼层
用这个试试

本帖子中包含更多资源

您需要 登录 才可以下载或查看,没有账号?立即注册

×

点评

k2p a1 刷了这个breed 变砖了  发表于 2024-12-15 08:57
感谢,可以使用,这个九口路由太小众,找的固件很难有完美匹配的,大佬有没有可以推荐的固件试试,最主要想用VLAN这个功能,但找了很多都端口都不对应,而且最多显示五口,剩下的四口都无法显示。  详情 回复 发表于 2024-12-10 22:47
只谈技术、莫论政事!(点击见详情) | 恩山无线论坛欢迎您的来访,请互相尊重、友善交流,建议保持一颗平常心看待网友的评论,切勿过度反应。
回复 支持 反对

使用道具 举报

 楼主| 发表于 2024-12-10 22:47 | 显示全部楼层

感谢,可以使用,这个九口路由太小众,找的固件很难有完美匹配的,大佬有没有可以推荐的固件试试,最主要想用VLAN这个功能,但找了很多都端口都不对应,而且最多显示五口,剩下的四口都无法显示。

点评

后面4口是一个交换机芯片里面的,不再CPU里面,肯定看不到  详情 回复 发表于 2024-12-11 18:21
只谈技术、莫论政事!(点击见详情) | 恩山无线论坛欢迎您的来访,请互相尊重、友善交流,建议保持一颗平常心看待网友的评论,切勿过度反应。
回复 支持 反对

使用道具 举报

发表于 2024-12-11 17:46 | 显示全部楼层
需要啥固件,高恪,集客都能用,都带vlan
只谈技术、莫论政事!(点击见详情) | 恩山无线论坛欢迎您的来访,请互相尊重、友善交流,建议保持一颗平常心看待网友的评论,切勿过度反应。
回复 支持 反对

使用道具 举报

发表于 2024-12-11 18:21 | 显示全部楼层
myxieyuyan 发表于 2024-12-10 22:47
感谢,可以使用,这个九口路由太小众,找的固件很难有完美匹配的,大佬有没有可以推荐的固件试试,最主要 ...

后面4口是一个交换机芯片里面的,不再CPU里面,肯定看不到
只谈技术、莫论政事!(点击见详情) | 恩山无线论坛欢迎您的来访,请互相尊重、友善交流,建议保持一颗平常心看待网友的评论,切勿过度反应。
回复 支持 反对

使用道具 举报

您需要登录后才可以回帖 登录 | 立即注册

本版积分规则

关闭

欢迎大家光临恩山无线论坛上一条 /1 下一条

有疑问请添加管理员QQ86788181|手机版|小黑屋|Archiver|恩山无线论坛(常州市恩山计算机开发有限公司版权所有) ( 苏ICP备05084872号 )

GMT+8, 2025-2-11 13:12

Powered by Discuz! X3.5

© 2001-2025 Discuz! Team.

| 江苏省互联网有害信息举报中心 举报信箱:js12377 | @jischina.com.cn 举报电话:025-88802724 本站不良内容举报信箱:68610888@qq.com

快速回复 返回顶部 返回列表