RT3052F的机子，帮看看能刷哪个版本的DD、、

swq01

H57V2562GTR-60C

S29GL064N

这个应该是TTL吧

不知道能刷哪个固件
要不要刷UBOOT呢

swq01

U-Boot 1.1.3 (Jul 12 2012 - 14:11:28)

Board: Ralink APSoC DRAM:  64 MB
relocate_code Pointer at: 83fac000
config usb..

Set info->start[0]=BF000000
flash_protect ON: from 0xBF000000 to 0xBF01F3BF
flash_protect ON: from 0xBF030000 to 0xBF030FFF
*** Warning - bad CRC, using default environment

============================================
Ralink UBoot Version: 3.6.0.0
--------------------------------------------
ASIC 3052_MP2 (Port5<->None)
DRAM component: 256 Mbits SDR
DRAM bus: 32 bit
Total memory: 64 MBytes
Flash component: NOR Flash
Date:Jul 12 2012  Time:14:11:28
============================================
icache: sets:256, ways:4, linesz:32 ,total:32768
dcache: sets:128, ways:4, linesz:32 ,total:16384

##### The CPU freq = 384 MHZ ####
estimate memory size =64 Mbytes
## Booting image at bf050000 ...
   Image Name:   Linux Kernel Image
   Created:      2012-07-12   6:11:20 UTC
   Image Type:   MIPS Linux Kernel Image (lzma compressed)
   Data Size:    6734534 Bytes =  6.4 MB
   Load Address: 80000000
   Entry Point:  80413000
   Verifying Checksum ... OK
   Uncompressing Kernel Image ... OK
No initrd
## Transferring control to Linux (at address 80413000) ...
## Giving linux memsize in MB, 64

Starting kernel ...


LINUX started...

THIS IS ASIC
Linux version 2.6.21 (root@localhost.localdomain) (gcc version 3.4.2) #7 Thu Jul 12 14:11:06 CST 2012

The CPU frequency set to 384 MHz
CPU revision is: 0001964c
Determined physical RAM map:
memory: 04000000 @ 00000000 (usable)
Built 1 zonelists.  Total pages: 16256
Kernel command line: console=ttyS1,57600n8 root=/dev/mtdblock5
Primary instruction cache 32kB, physically tagged, 4-way, linesize 32 bytes.
Primary data cache 16kB, 4-way, linesize 32 bytes.
Synthesized TLB refill handler (20 instructions).
Synthesized TLB load handler fastpath (32 instructions).
Synthesized TLB store handler fastpath (32 instructions).
Synthesized TLB modify handler fastpath (31 instructions).
Cache parity protection disabled
cause = c0808044, status = 11000000
PID hash table entries: 256 (order: 8, 1024 bytes)
calculating r4koff... 00177000(1536000)
CPU frequency 384.00 MHz
Using 192.000 MHz high precision timer.
Console: colour dummy device 80x25
Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
Memory: 60440k/65536k available (3041k kernel code, 5032k reserved, 1126k data, 124k init, 0k highmem)
Mount-cache hash table entries: 512
NET: Registered protocol family 16
SCSI subsystem initialized
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
NET: Registered protocol family 2
Time: MIPS clocksource has been installed.
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
TCP established hash table entries: 2048 (order: 2, 16384 bytes)
TCP bind hash table entries: 2048 (order: 1, 8192 bytes)
TCP: Hash tables configured (established 2048 bind 2048)
TCP reno registered
ralink flash device: 0x1000000 at 0x1f000000
Ralink SoC physically mapped flash: Found 1 x16 devices at 0x0 in 16-bit bank
Amd/Fujitsu Extended Query Table at 0x0040
number of CFI chips: 1
cfi_cmdset_0002: Disabling erase-suspend-program due to code brokenness.
Creating 7 MTD partitions on "Ralink SoC physically mapped flash":
0x00000000-0x00800000 : "ALL"
0x00000000-0x00030000 : "Bootloader"
0x00030000-0x00040000 : "Config"
0x00040000-0x00050000 : "Factory"
0x00050000-0x001ab306 : "Kernel"
mtd: partition "Kernel" doesn't end on an erase block -- force read-only
0x001ab306-0x01000000 : "RootFS"
mtd: partition "RootFS" extends beyond the end of device "Ralink SoC physically mapped flash" -- size truncated to 0x654cfa
mtd: partition "RootFS" doesn't start on an erase block boundary -- force read-only
0x00050000-0x01000000 : "Kernel_RootFS"
mtd: partition "Kernel_RootFS" extends beyond the end of device "Ralink SoC physically mapped flash" -- size truncated to 0x7b0000
squashfs: version 3.2-r2 (2007/01/15) Phillip Lougher
squashfs: LZMA suppport for slax.org by jro
JFFS2 version 2.2. (NAND) (C) 2001-2006 Red Hat, Inc.
fuse init (API version 7.8)
io scheduler noop registered (default)
Ralink gpio driver initialized
HDLC line discipline: version $Revision: 1.1.1.1 $, maxframe=4096
N_HDLC line discipline registered.
Serial: 8250/16550 driver $Revision: 1.8 $ 2 ports, IRQ sharing disabled
serial8250: ttyS0 at I/O 0xb0000500 (irq = 37) is a 16550A
serial8250: ttyS1 at I/O 0xb0000c00 (irq = 12) is a 16550A
loop: loaded (max 8 devices)
rdm_major = 253

eth2 mii.o query= phy_id:0, address:1 retval:7849
Ralink APSoC Ethernet Driver Initilization. v2.1  256 rx/tx descriptors allocated, mtu = 1500!
MAC_ADRH -- : 0x000000e0
MAC_ADRL -- : 0x4b9a186f
PROC INIT OK!
IMQ starting with 4 devices...
IMQ driver loaded successfully.
        Hooking IMQ before NAT on PREROUTING.
        Hooking IMQ after NAT on POSTROUTING.
PPP generic driver version 2.4.2
PPP BSD Compression module registered
NET: Registered protocol family 24
PPPoL2TP kernel driver, V0.17
PPTP driver version 0.8.1
SCSI Media Changer driver v0.25
block2mtd: version $Revision: 1.1.1.1 $
usbmon: debugfs is not available
usbcore: registered new interface driver usblp
drivers/usb/class/usblp.c: v0.13: USB Printer Device Class driver
usbcore: registered new interface driver libusual
GACT probability NOT on
netem: version 1.2
u32 classifier
    Performance counters on
    input device check on
    Actions configured
nf_conntrack version 0.5.0 (512 buckets, 4096 max)
ip_tables: (C) 2000-2006 Netfilter Core Team, Type=Restricted Cone
ipt_time loading
TCP cubic registered
NET: Registered protocol family 1
NET: Registered protocol family 10
NET: Registered protocol family 17
802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>
All bugs added by David S. Miller <davem@redhat.com>
VFS: Mounted root (squashfs filesystem) readonly.
Freeing unused kernel memory: 124k freed
init started: BusyBox v1.12.1 (2012-07-12 13:55:48 CST)
Bad inittab entry at line 2
Algorithmics/MIPS FPU Emulator v1.5
mount: no /etc/mtab
mount: no /devpts: called with bogus options
etc/mtab
-------------------------------------------------

swq01

Password for 'admin' changed
dwc_otg: version 2.72a 24-JUN-2008
DWC_otg: Core Release: 2.66a
DWC_otg: Periodic Transfer Interrupt Enhancement - disabled
DWC_otg: Multiprocessor Interrupt Enhancement - disabled
DWC_otg: Using DMA mode
DWC_otg: Device using Buffer DMA mode
dwc_otg lm0: DWC OTG Controller
dwc_otg lm0: new USB bus registered, assigned bus number 1
dwc_otg lm0: irq 18, io mem 0x00000000
DWC_otg: Init: Port Power? op_state=1
DWC_otg: Init: Power Port (0)
usb usb1: Product: DWC OTG Controller
usb usb1: Manufacturer: Linux 2.6.21 dwc_otg_hcd
usb usb1: SerialNumber: lm0
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 1 port detected
Initializing USB Mass Storage driver...
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.

phy_tx_ring = 0x03d24000, tx_ring = 0xa3d24000

phy_rx_ring0 = 0x03d25000, rx_ring0 = 0xa3d25000
MAC_ADRH -- : 0x000000e0
MAC_ADRL -- : 0x4b9a186f
CDMA_CSG_CFG = 81000007
GDMA1_FWD_CFG = 1710000
switchTableDel: done!
switchTableDel: done!
switchTableDel: done!
switchTableDel: done!
switchTableDel: done!

eth2 mii.o query= phy_id:1, address:4 retval:5e1

eth2 mii.o query= phy_id:1, address:0 retval:3100

eth2 mii.o query= phy_id:1, address:5 retval:0
eth2.2: dev_set_promiscuity(master, 1)
device eth2 entered promiscuous mode
device eth2.2 entered promiscuous mode

eth2 mii.o query= phy_id:1, address:4 retval:5e1

eth2 mii.o query= phy_id:1, address:0 retval:3100

eth2 mii.o query= phy_id:1, address:5 retval:0
eth2.3: dev_set_promiscuity(master, 1)
device eth2.3 entered promiscuous mode

eth2 mii.o query= phy_id:1, address:4 retval:5e1

eth2 mii.o query= phy_id:1, address:0 retval:3100

eth2 mii.o query= phy_id:1, address:5 retval:0
eth2.4: dev_set_promiscuity(master, 1)
device eth2.4 entered promiscuous mode

eth2 mii.o query= phy_id:1, address:4 retval:5e1

eth2 mii.o query= phy_id:1, address:0 retval:3100

eth2 mii.o query= phy_id:1, address:5 retval:0
eth2.5: dev_set_promiscuity(master, 1)
device eth2.5 entered promiscuous mode
rt2860v2_ap: module license 'unspecified' taints kernel.


=== pAd = c00e8000, size = 805344 ===

<-- RTMPAllocAdapterBlock, Status=0
RX DESC a3e27000  size = 2048
<-- RTMPAllocTxRxRingMemory, Status=0
1. Phy Mode = 9
2. Phy Mode = 9
3. Phy Mode = 9
MCS Set = ff ff 00 00 01
Main bssid = 00:e0:4b:9a:18:70
<==== rt28xx_init, Status=0
0x1300 = 00064380
device ra0 entered promiscuous mode
ipt_account 0.1.21 : Piotr Gasidlo <quaker@barbara.eu.org>, http://www.barbara.eu.org/~quaker/ipt_account/
br0: port 5(ra0) entering learning state
br0: port 4(eth2.5) entering learning state
br0: port 3(eth2.4) entering learning state
br0: port 2(eth2.3) entering learning state
br0: port 1(eth2.2) entering learning state

***** g_wl_interface = ra0 ******

eth2.1: Setting MAC address to  00 e0 4b 9a 18 6e.
write offset 0x60, value 0x2dc
webs: Listening for HTTP requests at address 192.168.1.1
WAN link UP -> DOWN
RTNETLINK answers: No such file or directory
RTNETLINK answers: No such file or directory
RTNETLINK answers: No such file or directory
RtmpOSNetDevDetach(): RtmpOSNetDeviceDetach(), dev->name=ra0!


=== pAd = c00ea000, size = 805344 ===

<-- RTMPAllocAdapterBlock, Status=0
RX DESC a3e77000  size = 2048
<-- RTMPAllocTxRxRingMemory, Status=0
1. Phy Mode = 9
2. Phy Mode = 9
3. Phy Mode = 9
MCS Set = ff ff 00 00 01
Main bssid = 00:e0:4b:9a:18:70
<==== rt28xx_init, Status=0
0x1300 = 00064380
^@^@

这是我的TTL信息
但我刷G300N和D600的DD都刷不进

swq01

U-Boot 1.1.3 (Jul 12 2012 - 14:11:28)

Board: Ralink APSoC DRAM:  64 MB
relocate_code Pointer at: 83fac000
config usb..

Set info->start[0]=BF000000
flash_protect ON: from 0xBF000000 to 0xBF01F3BF
flash_protect ON: from 0xBF030000 to 0xBF030FFF
*** Warning - bad CRC, using default environment

============================================
Ralink UBoot Version: 3.6.0.0
--------------------------------------------
ASIC 3052_MP2 (Port5<->None)
DRAM component: 256 Mbits SDR
DRAM bus: 32 bit
Total memory: 64 MBytes
Flash component: NOR Flash
Date:Jul 12 2012  Time:14:11:28
============================================
icache: sets:256, ways:4, linesz:32 ,total:32768
dcache: sets:128, ways:4, linesz:32 ,total:16384

##### The CPU freq = 384 MHZ ####
estimate memory size =64 Mbytes
Reset pressed, entering rescue mode!

   
10: System Load Firmware then write to Flash via TFTP.
        Input device IP (192.168.1.123)         Input server IP (192.168.1.100)Input Linux Kernel filename ()
netboot_common, argc= 3

NetTxPacket = 0x83FE36C0

KSEG1ADDR(NetTxPacket) = 0xA3FE36C0

NetLoop,call eth_halt !

NetLoop,call eth_init !
Trying Eth0 (10/100-M)

Waitting for RX_DMA_BUSY status Start... done


Header Payload scatter function is Disable !!

ETH_STATE_ACTIVE!!
Using Eth0 (10/100-M) device
TFTP from server 192.168.1.100; our IP address is 192.168.1.123
Filename 'firmware.bin'.

TIMEOUT_COUNT=10,Load address: 0x80100000
Loading: Got ARP REPLY, set server/gtwy eth addr (6c:f0:49:78:ec:0f)
Got it
T T T T T T T T T T
Retry count exceeded; starting again
Trying Eth0 (10/100-M)

ETH_STATE_ACTIVE!!
Got ARP REQUEST, return our IP
Using Eth0 (10/100-M) device
TFTP from server 192.168.1.100; our IP address is 192.168.1.123
Filename 'firmware.bin'.

TIMEOUT_COUNT=10,Load address: 0x80100000
Loading: Got ARP REPLY, set server/gtwy eth addr (6c:f0:49:78:ec:0f)
Got it
T T T T T T T T T T

按RESET键后的TTL信息
传到192.168.1.123
也传不进

xll

dd貌似没有支持ra的8M固件吧。
刷op吧，包你爽！

swq01

老兄推荐个能刷的OP吧

ly_0420

两个闪？

hanamchi

看不到图

swq01

{:soso_e127:}
怎么突然没图了
重新传了下

明明73

刷华硕的13b1可以，TT也行，open也行

swq01

{:soso_e127:}
没破解UBOOT
刷不进