jackseparo 发表于 2024-4-3 11:00

Password u boot 我需要

Boot NAND
start read bootheader
start read secondboot
non secure boot
Jump

123;S127s
DW2;
ddr3 init completed, clk_sel: 2, rate is 1333Mbps
ddr size is 256 MiB
ddr3 resize ok

ddr init done.
C:EA000014
........
!

U-Boot 2013.04 (Sep 27 2023 - 16:11:40)

1000MHZ
CPU: ZX279127S@A9,Board: ZXIC zx279127sevb
DRAM:256 MiB
BOOT:Boot Ext Params found!
DDR Type : DDR3
DDR Freq : 1333M
DDR Width: 16bit
Boot Mode: 1
NAND Special:0
Manu ID: 0x2c, Chip ID: 0xda (Micron NAND 256MiB 3,3V 8-bit)
NAND:256 MiB


<nand_read_skip_bad_,1478>!mtdpart=0x5,mtdPartOffset=0x00200000,mtdPartSize=0x00100000,offset=0x0,length=0x1000
g_is_auto_ponmode =1.
zx_vid_load USE FIXED VID !!!
ZXIC_SOFT_VID:5
product_vid = 5
board_index=8, vid=5, board_name=GM220-S
*0****pcie0 wifi reset pin=1
*1****pcie0 wifi reset pin=0
pass pinmux for flash
is_auto_ponmode: 1
eth_led_polar: 0
<nand_read_skip_bad_,1478>!mtdpart=0x2,mtdPartOffset=0x00180000,mtdPartSize=0x00080000,offset=0x0,length=0x20000
In:    serial
Out:   serial
Err:   serial
i2c clk speed: 100 kHz
debug: bob ic type is !
debug: bob mcu mode is !
uboot write_all_datas_to_GN25L95
uboot write_data_to_GN25L95 NG,addr=113(0x71),data=64(0x40)
uboot write_data_to_GN25L95 NG,addr=169(0xA9),data=67(0x43)
uboot write_data_to_GN25L95 NG,addr=170(0xAA),data=128(0x80)
uboot write_data_to_GN25L95 NG,addr=171(0xAB),data=85(0x55)
clk_pll env is not setted, core clk won't change
Net:   enter ref_clk_set.. mode = 0 .
enter pll_cfg_fractional
ref_clk_set success!
gpon serdes init
tm_pon_tm_init
after pon_tm_qmg_init
auto switch.now the state is los.rx state = 0x30.
use the last pon mode:gpon.
innerGeLedPolarSet 0
innerGeLedPolarSet 0
innerGeLedPolarSet 0
innerGeLedPolarSet 0
eth0
Hit any key to stop autoboot:0

### Please input uboot password:



Password u boot 我需要

iamyangyi 发表于 2024-4-3 11:35

问中兴            

zack2022 发表于 2024-4-3 12:27

本帖最后由 zack2022 于 2024-4-3 12:29 编辑

记得好像是Zxic521,之前开过,忘了
页: [1]
查看完整版本: Password u boot 我需要