淘宝一台TOTOLINK 无线路由 拆机 清洗 后 大家看看

老子***

亲大家看看  这货  是多大 内存  还有两条
我有百度 说是
http://zhidao.baidu.com/link?url=D6BOc0xcdNYAzxxaacgwWz7hZeu51jpaSu_d2TP9ICBtka5dOOyBP3NWmyWHlX--EE80J_dWHsdcRurNg33cja

不不信  还有这机器可以刷什么？？？
上面接口都很齐  ；就是闪存  让我蛋疼   （没搞过）我这里只有8脚 16脚

大家帮我看看 CPU  应该是什么  ？？？ 我在3楼  上 tTTL   (com   56700)
上图

遗失***

散热片摘下  才能看见cpu的型号

老子***

这里上TTL
(Feb 20 2009 - 15:32:41)

Board: Ralink APSoC DRAM:  16 MB
relocate_code Pointer at: 80fb4000

Set info->start[0]=BFC00000
*** Warning - bad CRC, using default environment

============================================
Ralink UBoot Version: 3.1
--------------------------------------------
ASIC 3052_MP1 (MAC to GigaMAC Mode)
DRAM COMPONENT: 64Mbits
DRAM BUS: 32BIT
Total memory: 16 MBytes
Flash: 2 MBytes
Date:Feb 20 2009  Time:15:32:41
============================================
icache: sets:256, ways:4, linesz:32 ,total:32768
dcache: sets:128, ways:4, linesz:32 ,total:16384

##### The CPU freq = 384 MHZ ####

SDRAM bus set to 32 bit
SDRAM size =16 Mbytes
Disable WAN Port: 0

Please choose the operation: (t:tftp server/b(boot now)/f(flash test))

BootType => b
## Booting image at bfc30000 ...
   Image Name:   n200r
   Created:      2010-09-09   2:33:42 UTC

System Control Status = 0x20440000
   Image Type:   MIPS Linux Kernel Image (lzma compressed)
   Data Size:    1843136 Bytes =  1.8 MB
   Load Address: 80000000
   Entry Point:  802cb000
   Verifying Checksum ... OK
   Uncompressing Kernel Image ... OK
No initrd
## Transferring control to Linux (at address 802cb000) ...
## Giving linux memsize in MB, 16

Starting kernel ...


LINUX started...

THIS IS ASIC
2860 version : 2.0.0.0 (Sep  9 2010)
RT3052D0 Chipset
Use NOR(Parallel) Flash
--> Init Smart QoS Monitor
Ralink APSoC Ethernet Driver Initilization. v2.00  256 rx/tx descriptors allocated, mtu = 1500!
ADDR===>00:0e:e8:a8:81:ac
alias:n200r version:7.28
Default Configuration
Init LED ->[ Blinking ]
Bridge Init


=========================================
RALINK WIRELESS MODULE DETECTED!!
=========================================


device apcli0 is not a slave of br0



=================================================================
press magic key to change default setting ...
  LAN MAC : 00:0E:E8:A8:81:AD
  WAN MAC : 00:0E:E8:A8:81:AE
WAN IFNAME => [eth2.2]
iptables: No chain/target/match by that name
Jan  1 00:00:03 miniupnpd[212]: Reloading rules from lease file
Jan  1 00:00:03 miniupnpd[212]: could not open lease file: /var/run/upnp_pmlist
Jan  1 00:00:03 miniupnpd[212]: HTTP listening on port 3183
SIGNAL -> Config Update signal progress
Check DHCP PID Elapsed Time: 0
SIGNAL -> WAN ip changed
Reaped 210
Reaped 211

老子***

遗失的梦想 发表于 2014-3-20 17:54
散热片摘下  才能看见cpu的型号

W 我已经TTL    信息  就在楼下

爱若***

2M的flash，16M内存

老子***

爱若晨风 发表于 2014-3-20 18:03
2M的flash，16M内存

内存  那 不是两块  8M  加起拉地？？

free***

totolink n300r 吧

Ralink 3052F  16M内存

a2918***

看到刷sdram颗粒你应该就想到3050  3052  最有可能是3050

snipe***

48脚的2M闪存，16M内存～～估计要硬改

爱若***

老子本姓天 发表于 2014-3-20 18:09
内存  那 不是两块  8M  加起拉地？？

如果是RT3052的话硬改16M+64M之后固件应该和HG255d通用

老子***

如果是RT3052的话硬改16M+64M之
还是 不要折腾了 就用原来地  固件    来中需

wwn***

一看到29系列的闪存就比较蛋疼!

asi***

2M的flash，16M内存

asi***

怎么感觉和TP的一样的烂？

WXYH***

這個不好整........