mw305r-16m-mt7620n-无能为力了，帮忙测试下是固件问题还是我机器问题

na***

前几天入手mw305r，改了机器，闪存16m，刷其他的8m固件能保存配置，自己编译的16m固件，可以启动，但是掉电就初始化，弄了好几天也没有什么结果，不知道是我机器问题，还是编译的问题，现在发出来，请人帮忙看看在其他机器正常么？
我刷的是zbt-wa05，我刷rt-n14u灯不正常，
http://pan.baidu.com/s/1gd3oVSn在此谢谢了

新手另请教：编译怎么改16m，自己摸索着改的，不知道我改对了没……
                     固件波特率57600跟固件115200有什么差异吗？           

na***

有没有帮忙测试下

mxl***

看ttl启动，然后发图，还是有人回复的，这样没人去测试的

981***

你描述下你是怎么改的16M?

na***

981213 发表于 2014-12-28 17:29
你描述下你是怎么改的16M?

用了官方的trunk，和你的代码都试了，都是16m掉配置，初始化，8m没事，
改的方法为openwrt/target/linux/ramips/image/Makefile，改的zbt-wa05，将8m改为16m

openwrt/target/linux/ramips/dts/ZBT-WA05.dts，，

partition@50000 {
                                        label = "firmware";
                                        reg = <0x50000 0x760000>;
                                };

0x760000改了0xfb0000

uboot用的是http://downloads.openwrt.org.cn/PandoraBox/MW305R/u-boot/

981***

naypt 发表于 2015-1-3 10:14
用了官方的trunk，和你的代码都试了，都是16m掉配置，初始化，8m没事，
改的方法为openwrt/target/linux ...

改法是没错。。。。。。
贴一下内核日志看看

na***

981213 发表于 2015-1-3 10:23
改法是没错。。。。。。
贴一下内核日志看看

首先谢谢你帮忙看，十分感谢

[    0.000000] Linux version 3.14.26 (naypt@naypt-desktop) (gcc version 4.8.3 (OpenWrt/Linaro GCC 4.8-2014.04 r43693) ) #3 Mon Dec 29 13:28:36 CST 2014
[    0.000000] Board has DDR1
[    0.000000] Analog PMU set to hw control
[    0.000000] Digital PMU set to hw control
[    0.000000] SoC Type: Ralink MT7620N ver:2 eco:3
[    0.000000] bootconsole [early0] enabled
[    0.000000] CPU0 revision is: 00019650 (MIPS 24KEc)
[    0.000000] MIPS: machine is Zbtlink ZBT-WA05
[    0.000000] Determined physical RAM map:
[    0.000000]  memory: 04000000 @ 00000000 (usable)
[    0.000000] Initrd not found or empty - disabling initrd
[    0.000000] Zone ranges:
[    0.000000]   Normal   [mem 0x00000000-0x03ffffff]
[    0.000000] Movable zone start for each node
[    0.000000] Early memory node ranges
[    0.000000]   node   0: [mem 0x00000000-0x03ffffff]
[    0.000000] On node 0 totalpages: 16384
[    0.000000] free_area_init_node: node 0, pgdat 802e2500, node_mem_map 81003e40
[    0.000000]   Normal zone: 128 pages used for memmap
[    0.000000]   Normal zone: 0 pages reserved
[    0.000000]   Normal zone: 16384 pages, LIFO batch:3
[    0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
[    0.000000] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
[    0.000000] pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768
[    0.000000] pcpu-alloc: [0] 0
[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 16256
[    0.000000] Kernel command line: console=ttyS0,115200 rootfstype=squashfs,jffs2
[    0.000000] PID hash table entries: 256 (order: -2, 1024 bytes)
[    0.000000] Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
[    0.000000] Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
[    0.000000] Writing ErrCtl register=0000000a
[    0.000000] Readback ErrCtl register=0000000a
[    0.000000] Memory: 61508K/65536K available (2423K kernel code, 128K rwdata, 492K rodata, 148K init, 184K bss, 4028K reserved)
[    0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[    0.000000] NR_IRQS:256
[    0.000000] CPU Clock: 620MHz
[    0.000000] systick: running - mult: 214748, shift: 32
[    0.000000] genirq: Flags mismatch irq 7. 00014600 (timer) vs. 00014600 (systick)
[    0.040000] Calibrating delay loop... 824.11 BogoMIPS (lpj=4120576)
[    0.040000] pid_max: default: 32768 minimum: 301
[    0.040000] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
[    0.040000] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
[    0.050000] pinctrl core: initialized pinctrl subsystem
[    0.050000] NET: Registered protocol family 16
[    0.060000] rt2880-pinmux pinctrl.1: try to register 73 pins ...
[    0.060000] pinctrl core: registered pin 0 (io0) on rt2880-pinmux
[    0.060000] pinctrl core: registered pin 1 (io1) on rt2880-pinmux
[    0.060000] pinctrl core: registered pin 2 (io2) on rt2880-pinmux
[    0.060000] pinctrl core: registered pin 3 (io3) on rt2880-pinmux
[    0.060000] pinctrl core: registered pin 4 (io4) on rt2880-pinmux
[    0.060000] pinctrl core: registered pin 5 (io5) on rt2880-pinmux
[    0.060000] pinctrl core: registered pin 6 (io6) on rt2880-pinmux
[    0.060000] pinctrl core: registered pin 7 (io7) on rt2880-pinmux
[    0.060000] pinctrl core: registered pin 8 (io8) on rt2880-pinmux
[    0.060000] pinctrl core: registered pin 9 (io9) on rt2880-pinmux
[    0.060000] pinctrl core: registered pin 10 (io10) on rt2880-pinmux
[    0.060000] pinctrl core: registered pin 11 (io11) on rt2880-pinmux
[    0.060000] pinctrl core: registered pin 12 (io12) on rt2880-pinmux
[    0.060000] pinctrl core: registered pin 13 (io13) on rt2880-pinmux
[    0.060000] pinctrl core: registered pin 14 (io14) on rt2880-pinmux
[    0.060000] pinctrl core: registered pin 15 (io15) on rt2880-pinmux
[    0.060000] pinctrl core: registered pin 16 (io16) on rt2880-pinmux
[    0.060000] pinctrl core: registered pin 17 (io17) on rt2880-pinmux
[    0.060000] pinctrl core: registered pin 18 (io18) on rt2880-pinmux
[    0.060000] pinctrl core: registered pin 19 (io19) on rt2880-pinmux
[    0.060000] pinctrl core: registered pin 20 (io20) on rt2880-pinmux
[    0.060000] pinctrl core: registered pin 21 (io21) on rt2880-pinmux
[    0.060000] pinctrl core: registered pin 22 (io22) on rt2880-pinmux
[    0.060000] pinctrl core: registered pin 23 (io23) on rt2880-pinmux
[    0.060000] pinctrl core: registered pin 24 (io24) on rt2880-pinmux
[    0.060000] pinctrl core: registered pin 25 (io25) on rt2880-pinmux
[    0.060000] pinctrl core: registered pin 26 (io26) on rt2880-pinmux
[    0.060000] pinctrl core: registered pin 27 (io27) on rt2880-pinmux
[    0.060000] pinctrl core: registered pin 28 (io28) on rt2880-pinmux
[    0.060000] pinctrl core: registered pin 29 (io29) on rt2880-pinmux
[    0.060000] pinctrl core: registered pin 30 (io30) on rt2880-pinmux
[    0.060000] pinctrl core: registered pin 31 (io31) on rt2880-pinmux
[    0.060000] pinctrl core: registered pin 32 (io32) on rt2880-pinmux
[    0.060000] pinctrl core: registered pin 33 (io33) on rt2880-pinmux
[    0.060000] pinctrl core: registered pin 34 (io34) on rt2880-pinmux
[    0.060000] pinctrl core: registered pin 35 (io35) on rt2880-pinmux
[    0.060000] pinctrl core: registered pin 36 (io36) on rt2880-pinmux
[    0.060000] pinctrl core: registered pin 37 (io37) on rt2880-pinmux
[    0.060000] pinctrl core: registered pin 38 (io38) on rt2880-pinmux
[    0.060000] pinctrl core: registered pin 39 (io39) on rt2880-pinmux
[    0.060000] pinctrl core: registered pin 40 (io40) on rt2880-pinmux
[    0.060000] pinctrl core: registered pin 41 (io41) on rt2880-pinmux
[    0.060000] pinctrl core: registered pin 42 (io42) on rt2880-pinmux
[    0.060000] pinctrl core: registered pin 43 (io43) on rt2880-pinmux
[    0.060000] pinctrl core: registered pin 44 (io44) on rt2880-pinmux
[    0.060000] pinctrl core: registered pin 45 (io45) on rt2880-pinmux
[    0.060000] pinctrl core: registered pin 46 (io46) on rt2880-pinmux
[    0.060000] pinctrl core: registered pin 47 (io47) on rt2880-pinmux
[    0.060000] pinctrl core: registered pin 48 (io48) on rt2880-pinmux
[    0.060000] pinctrl core: registered pin 49 (io49) on rt2880-pinmux
[    0.060000] pinctrl core: registered pin 50 (io50) on rt2880-pinmux
[    0.060000] pinctrl core: registered pin 51 (io51) on rt2880-pinmux
[    0.060000] pinctrl core: registered pin 52 (io52) on rt2880-pinmux
[    0.060000] pinctrl core: registered pin 53 (io53) on rt2880-pinmux
[    0.060000] pinctrl core: registered pin 54 (io54) on rt2880-pinmux
[    0.060000] pinctrl core: registered pin 55 (io55) on rt2880-pinmux
[    0.060000] pinctrl core: registered pin 56 (io56) on rt2880-pinmux
[    0.060000] pinctrl core: registered pin 57 (io57) on rt2880-pinmux
[    0.060000] pinctrl core: registered pin 58 (io58) on rt2880-pinmux
[    0.060000] pinctrl core: registered pin 59 (io59) on rt2880-pinmux
[    0.060000] pinctrl core: registered pin 60 (io60) on rt2880-pinmux
[    0.060000] pinctrl core: registered pin 61 (io61) on rt2880-pinmux
[    0.060000] pinctrl core: registered pin 62 (io62) on rt2880-pinmux
[    0.060000] pinctrl core: registered pin 63 (io63) on rt2880-pinmux
[    0.060000] pinctrl core: registered pin 64 (io64) on rt2880-pinmux
[    0.060000] pinctrl core: registered pin 65 (io65) on rt2880-pinmux
[    0.060000] pinctrl core: registered pin 66 (io66) on rt2880-pinmux
[    0.060000] pinctrl core: registered pin 67 (io67) on rt2880-pinmux
[    0.060000] pinctrl core: registered pin 68 (io68) on rt2880-pinmux
[    0.060000] pinctrl core: registered pin 69 (io69) on rt2880-pinmux
[    0.060000] pinctrl core: registered pin 70 (io70) on rt2880-pinmux
[    0.060000] pinctrl core: registered pin 71 (io71) on rt2880-pinmux
[    0.060000] pinctrl core: registered pin 72 (io72) on rt2880-pinmux
[    0.060000] pinctrl core: add 3 pinmux maps
[    0.060000] rt2880-pinmux pinctrl.1: found group selector 0 for i2c
[    0.060000] rt2880-pinmux pinctrl.1: found group selector 7 for spi refclk
[    0.060000] rt2880-pinmux pinctrl.1: found group selector 11 for wled
[    0.060000] rt2880-pinmux pinctrl.1: request pin 1 (io1) for pinctrl.1
[    0.060000] rt2880-pinmux pinctrl.1: request pin 2 (io2) for pinctrl.1
[    0.060000] rt2880-pinmux pinctrl.1: request pin 37 (io37) for pinctrl.1
[    0.060000] rt2880-pinmux pinctrl.1: request pin 38 (io38) for pinctrl.1
[    0.060000] rt2880-pinmux pinctrl.1: request pin 39 (io39) for pinctrl.1
[    0.060000] rt2880-pinmux pinctrl.1: request pin 72 (io72) for pinctrl.1
[    0.060000] rt2880-pinmux pinctrl.1: failed to lookup the sleep state
[    0.060000] bio: create slab <bio-0> at 0
[    0.060000] rt2880_gpio 10000600.gpio: registering 24 gpios
[    0.070000] rt2880_gpio 10000600.gpio: registering 24 irq handlers
[    0.070000] rt2880_gpio 10000638.gpio: registering 16 gpios
[    0.070000] rt2880_gpio 10000638.gpio: registering 16 irq handlers
[    0.070000] rt2880_gpio 10000660.gpio: registering 32 gpios
[    0.080000] rt2880_gpio 10000660.gpio: registering 32 irq handlers
[    0.080000] rt2880_gpio 10000688.gpio: registering 1 gpios
[    0.080000] rt2880_gpio 10000688.gpio: registering 1 irq handlers
[    0.090000] Switched to clocksource systick
[    0.090000] NET: Registered protocol family 2
[    0.090000] TCP established hash table entries: 1024 (order: 0, 4096 bytes)
[    0.100000] TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
[    0.110000] TCP: Hash tables configured (established 1024 bind 1024)
[    0.110000] TCP: reno registered
[    0.120000] UDP hash table entries: 256 (order: 0, 4096 bytes)
[    0.120000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[    0.130000] NET: Registered protocol family 1
[    0.130000] PCI: CLS 0 bytes, default 32
[    0.130000] rt-timer 10000100.timer: maximum frequency is 2441Hz
[    0.140000] alarmtimer alarmtimer: no of_node; not parsing pinctrl DT
[    0.140000] futex hash table entries: 256 (order: -1, 3072 bytes)
[    0.160000] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[    0.170000] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[    0.180000] msgmni has been set to 120
[    0.180000] io scheduler noop registered
[    0.190000] io scheduler deadline registered (default)
[    0.190000] Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled
[    0.200000] serial8250 serial8250: no of_node; not parsing pinctrl DT
[    0.200000] pinctrl core: add 1 pinmux maps
[    0.200000] rt2880-pinmux pinctrl.1: found group selector 3 for uartlite
[    0.200000] rt2880-pinmux pinctrl.1: request pin 15 (io15) for 10000c00.uartlite
[    0.200000] rt2880-pinmux pinctrl.1: request pin 16 (io16) for 10000c00.uartlite
[    0.200000] 10000c00.uartlite: ttyS0 at MMIO 0x10000c00 (irq = 20, base_baud = 2500000) is a 16550A
[    0.210000] console [ttyS0] enabled
[    0.220000] bootconsole [early0] disabled
[    0.230000] pinctrl core: add 1 pinmux maps
[    0.230000] rt2880-pinmux pinctrl.1: found group selector 2 for spi
[    0.230000] rt2880-pinmux pinctrl.1: request pin 3 (io3) for 10000b00.spi
[    0.230000] rt2880-pinmux pinctrl.1: request pin 4 (io4) for 10000b00.spi
[    0.230000] rt2880-pinmux pinctrl.1: request pin 5 (io5) for 10000b00.spi
[    0.230000] rt2880-pinmux pinctrl.1: request pin 6 (io6) for 10000b00.spi
[    0.230000] m25p80 spi32766.0: found w25q128, expected mx25l12805d
[    0.230000] m25p80 spi32766.0: w25q128 (16384 Kbytes)
[    0.250000] 4 ofpart partitions found on MTD device spi32766.0
[    0.250000] Creating 4 MTD partitions on "spi32766.0":
[    0.250000] 0x000000000000-0x000000030000 : "u-boot"
[    0.250000] 0x000000030000-0x000000040000 : "u-boot-env"
[    0.270000] 0x000000040000-0x000000050000 : "factory"
[    0.270000] 0x000000050000-0x000000fd0000 : "firmware"
[    0.280000] 0x00000015fef0-0x000000fd0000 : "rootfs"
[    0.290000] mtd: partition "rootfs" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only
[    0.300000] mtd: device 4 (rootfs) set to be root filesystem
[    0.310000] 1 squashfs-split partitions found on MTD device rootfs
[    0.310000] 0x000000ca0000-0x000000fd0000 : "rootfs_data"
[    0.320000] ralink_soc_eth 10100000.ethernet: loaded mt7620 driver
[    0.330000] ralink_soc_eth 10100000.ethernet eth0: ralink at 0xb0100000, irq 5
[    0.340000] rt3xxx-usbphy usbphy.3: loaded
[    0.340000] rt2880_wdt 10000120.watchdog: Initialized
[    0.350000] TCP: cubic registered
[    0.350000] NET: Registered protocol family 17
[    0.360000] Bridge firewalling registered
[    0.360000] 8021q: 802.1Q VLAN Support v1.8
[    0.380000] VFS: Mounted root (squashfs filesystem) readonly on device 31:4.
[    0.390000] Freeing unused kernel memory: 148K (802fb000 - 80320000)
[    6.740000] usbcore: registered new interface driver usbfs
[    6.740000] usbcore: registered new interface driver hub
[    6.750000] usbcore: registered new device driver usb
[    6.790000] JFS: nTxBlock = 481, nTxLock = 3853
[    6.800000] rt2880-pinmux pinctrl.1: request pin 1 (io1) for pio:1
[    6.800000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[    6.800000] ehci-platform: EHCI generic platform driver
[    7.210000] rt3xxx-usbphy usbphy.3: remote usb device wakeup disabled
[    7.220000] rt3xxx-usbphy usbphy.3: UTMI 16bit 30MHz
[    7.220000] ehci-platform 101c0000.ehci: EHCI Host Controller
[    7.230000] ehci-platform 101c0000.ehci: new USB bus registered, assigned bus number 1
[    7.240000] ehci-platform 101c0000.ehci: irq 26, io mem 0x101c0000
[    7.260000] ehci-platform 101c0000.ehci: USB 2.0 started, EHCI 1.00
[    7.260000] usb usb1: no of_node; not parsing pinctrl DT
[    7.260000] hub 1-0:1.0: no of_node; not parsing pinctrl DT
[    7.260000] hub 1-0:1.0: USB hub found
[    7.270000] hub 1-0:1.0: 1 port detected
[    7.280000] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[    7.280000] ohci-platform: OHCI generic platform driver
[    7.290000] ohci-platform 101c1000.ohci: Generic Platform OHCI controller
[    7.300000] ohci-platform 101c1000.ohci: new USB bus registered, assigned bus number 2
[    7.300000] ohci-platform 101c1000.ohci: irq 26, io mem 0x101c1000
[    7.380000] usb usb2: no of_node; not parsing pinctrl DT
[    7.380000] hub 2-0:1.0: no of_node; not parsing pinctrl DT
[    7.380000] hub 2-0:1.0: USB hub found
[    7.380000] hub 2-0:1.0: 1 port detected
[    7.380000] rt2880-pinmux pinctrl.1: request pin 38 (io38) for pio:38
[    7.380000] rt2880-pinmux pinctrl.1: request pin 39 (io39) for pio:39
[    7.380000] rt2880-pinmux pinctrl.1: request pin 72 (io72) for pio:72
[    8.760000] 8021q: adding VLAN 0 to HW filter on device eth0
[    8.760000] random: mktemp urandom read with 98 bits of entropy available
[   15.320000] NET: Registered protocol family 10
[   15.320000] tun: Universal TUN/TAP device driver, 1.6
[   15.320000] tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
[   15.320000] gre: GRE over IPv4 demultiplexor driver
[   15.320000] ip_gre: GRE over IPv4 tunneling driver
[   15.840000] ip6_tables: (C) 2000-2006 Netfilter Core Team
[   15.860000] Netfilter messages via NETLINK v0.30.
[   15.860000] ip_set: protocol 6
[   15.880000] Loading modules backported from Linux version master-2014-11-04-0-gf3660a2
[   15.900000] Backport generated by backports.git backports-20141023-2-g4ff890b
[   15.930000] cfg80211: Calling CRDA to update world regulatory domain
[   15.930000] cfg80211: World regulatory domain updated:
[   15.940000] cfg80211:  DFS Master region: unset
[   15.940000] cfg80211:   (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp), (dfs_cac_time)
[   15.960000] cfg80211:   (2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A)
[   15.960000] cfg80211:   (2457000 KHz - 2482000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A)
[   15.960000] cfg80211:   (2474000 KHz - 2494000 KHz @ 20000 KHz), (N/A, 2000 mBm), (N/A)
[   15.980000] cfg80211:   (5170000 KHz - 5250000 KHz @ 80000 KHz), (N/A, 2000 mBm), (N/A)
[   15.990000] cfg80211:   (5250000 KHz - 5330000 KHz @ 80000 KHz, 160000 KHz AUTO), (N/A, 2000 mBm), (0 s)
[   15.990000] cfg80211:   (5490000 KHz - 5730000 KHz @ 160000 KHz), (N/A, 2000 mBm), (0 s)
[   16.010000] cfg80211:   (5735000 KHz - 5835000 KHz @ 80000 KHz), (N/A, 2000 mBm), (N/A)
[   16.010000] cfg80211:   (57240000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 0 mBm), (N/A)
[   16.050000] acx.acx_init_module: acx-mac80211, version: v0.6.0 (git: unknown)
[   16.050000] acx.acx_init_module: this driver is still EXPERIMENTAL
[   16.050000] acx: please read the README file and/or go to http://acx100.sourceforge.net/wiki for further information
[   16.080000] acx.acxpci_init_module: built with CONFIG_ACX_MAC80211_PCI
[   16.080000] acx.acxpci_init_module: compiled to use 32bit I/O access. I/O timing issues might occur, such as non-working firmware upload. Report them
[   16.100000] acx.acxpci_init_module: acx: running on a little-endian CPU
[   16.100000]  PCI/VLYNQ module initialized, waiting for cards to probe...
[   16.120000] u32 classifier
[   16.120000]     input device check on
[   16.120000]     Actions configured
[   16.120000] Mirror/redirect action on
[   16.180000] Ebtables v2.0 registered
[   16.180000] ip_tables: (C) 2000-2006 Netfilter Core Team
[   16.200000] nf_conntrack version 0.5.0 (963 buckets, 3852 max)
[   16.240000] usbcore: registered new interface driver rtl8187
[   16.300000] xt_time: kernel timezone is -0000
[   16.320000] PPP generic driver version 2.4.2
[   16.330000] NET: Registered protocol family 24
[   16.340000] PPTP driver version 0.8.5
[   16.360000] ieee80211 phy0: rt2x00_set_rt: Info - RT chipset 5390, rev 0500 detected
[   16.380000] ieee80211 phy0: rt2x00_set_rf: Info - RF chipset 7620 detected
[   16.380000] ieee80211 phy0: Selected rate control algorithm 'minstrel_ht'
[   19.930000] random: nonblocking pool is initialized
[   29.520000] 8021q: adding VLAN 0 to HW filter on device eth0
[   29.520000] device eth0.1 entered promiscuous mode
[   29.530000] device eth0 entered promiscuous mode
[   29.550000] br-lan: port 1(eth0.1) entered forwarding state
[   29.550000] br-lan: port 1(eth0.1) entered forwarding state
[   30.910000] cfg80211: Calling CRDA for country: CN
[   30.920000] cfg80211: Regulatory domain changed to country: CN
[   30.920000] cfg80211:  DFS Master region: FCC
[   30.920000] cfg80211:   (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp), (dfs_cac_time)
[   30.940000] cfg80211:   (2402000 KHz - 2482000 KHz @ 40000 KHz), (N/A, 2300 mBm), (N/A)
[   30.940000] cfg80211:   (5170000 KHz - 5250000 KHz @ 80000 KHz, 160000 KHz AUTO), (N/A, 2300 mBm), (N/A)
[   30.960000] cfg80211:   (5250000 KHz - 5330000 KHz @ 80000 KHz, 160000 KHz AUTO), (N/A, 2300 mBm), (0 s)
[   30.960000] cfg80211:   (5735000 KHz - 5835000 KHz @ 80000 KHz), (N/A, 2300 mBm), (N/A)
[   30.980000] cfg80211:   (57240000 KHz - 59400000 KHz @ 2160000 KHz), (N/A, 2800 mBm), (N/A)
[   30.980000] cfg80211:   (59400000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 4400 mBm), (N/A)
[   30.980000] cfg80211:   (63720000 KHz - 65880000 KHz @ 2160000 KHz), (N/A, 2800 mBm), (N/A)
[   31.550000] br-lan: port 1(eth0.1) entered forwarding state
[   34.920000] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
[   34.920000] device wlan0 entered promiscuous mode
[   34.920000] br-lan: port 2(wlan0) entered forwarding state
[   34.940000] br-lan: port 2(wlan0) entered forwarding state
[   34.940000] br-lan: port 2(wlan0) entered disabled state
[   47.990000] br-lan: port 2(wlan0) entered forwarding state
[   48.000000] br-lan: port 2(wlan0) entered forwarding state
[   48.000000] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
[   50.000000] br-lan: port 2(wlan0) entered forwarding state
[  188.330000] ralink_soc_eth 10100000.ethernet eth0: port 2 link up (100Mbps/Full duplex)

na***

是不是编译组件少了？我按的默认的，添加了一些软件

na***

naypt 发表于 2015-1-3 12:47
是不是编译组件少了？我按的默认的，添加了一些软件

我用UBOOT是用低调测试的不死UBOOT公版1#，刷固件不能启动，另外mw313是7620a？

brig***

我编译出来的怎么只有3.5M。最新的  barrier break 14.0.

brig***

naypt 发表于 2015-1-3 10:14
用了官方的trunk，和你的代码都试了，都是16m掉配置，初始化，8m没事，
改的方法为openwrt/target/linux ...

大师看看我这个路由器该怎么改文件？

brig***

我自己编译的刷进去是这样的情况：
U-Boot 1.1.4 (Nov 24 2014 - 13:38:42)

Ralink APSoC (MT7620 E2 ver 2, eco 3)
DRAM:  32 MB
Flash: Macronix MX25L6435E (8 MB)

Clocks: CPU:600MHz, Bus:120MHz
In:    serial
Out:   serial
Err:   serial
Net:   rt2880_eth_initialize...
VLAN: W/LLLL
Fetching MAC Address from 0xbc040028
eth0: 00:0c:43:76:20:77
eth0 up
eth0
Hit any key to stop autoboot:  0
## Booting image at 9c050000 ...
   Image Name:   MIPS OpenWrt Linux-3.10.49
   Created:      2015-01-19  18:32:39 UTC
   Image Type:   MIPS Linux Kernel Image (lzma compressed)
   Data Size:    1035127 Bytes = 1010.9 kB
   Load Address: 80000000
   Entry Point:  80000000
   Verifying Checksum at 0x9c050040 ... Bad Data CRC

na***

brightsm 发表于 2015-1-20 13:36
我自己编译的刷进去是这样的情况：
U-Boot 1.1.4 (Nov 24 2014 - 13:38:42)

你这个是ttl的信息？

brig***

naypt 发表于 2015-2-13 12:36
你这个是ttl的信息？

是呀。这是不死UBOOT。现在R自己编译的固件已经能跑起来了。

axis***

mw305r到底应该刷openwrt官方固件里对应哪个型号的固件呢，到目前为止我只测试到华硕n14u原厂固件可用