听说wr880N V1出OP固件了，想刷机，但TTL连机进不了命令行，怎么个情况

zli***

用SecureCRT，PUTTY在XP下WIN10下都一样，波特率115200：

奤K?媮1甃B
          諠0 矈j9'室拻)
C醓p1j殟缴羒on0莫5
srZC絩p樗
         妑
隕憆_i+嫢叡_co衰潯211)'B姴パddrLJ攻
tap 絺铝0000皰j奤羴(low珺? =B0x奤羴valuY.B0x1, 偮Eb,犅舃       偮舃)
FlX.
    j卬ufJ憗芭, T枼峞Id皞律, DeWk 0
+汀 si? sY,譑co鯆
+汀:  j   5
                                                                 Usin"暀卽l官?on鞾

**%簠晒ing*P肦YAN 蛬毡no2秸筪 !HHC岐%%簠rni雭*%晛WLA蝚綉誰e 顙乫?憗!!!崱蔏 骙
O]serZX獺ㄉ砷   sY
N鍡娧?漨acU箷裚in閃+饱ze.?
                                           矃眎d 曂s i
                                                       2眳蚳. U?fixY
                                                                    慸re螽H鴄th_V+峿昻et暪パial榀挄蜁ma拻00燙酳cK隶焦 --KK毶7 P萔?鳶27挄潄initC?!蒘2挄蚭tt殡乻?H鳤T泉*阂俿2挄蜁t d5夾THR应G 0Q--俲
                                   AT泉*阂x2鉑K液?e皻*5
                                                       ATH?x8-K覀j
                                                                   ATH?xc-K覀j
                                                                               ATH?x10KK襡
           呴釿'V閏e:耙?j
=筎RO                     atK蜕穮″}set]丄訨卐}
     見00癈醓thτ″}蚭tuAT泉卐_SP浓5EUM :1癈醓t璁.胡痢鍈set鮼ATJ呭_C蠆% 1 篖倐j
                                                                             athτ″}蚭tuQ!I_PHV礎峗STPU*:1癈醓t璁.胡痢鍈蚭t鮼ATJ呭_CO 2 篖倐j
_STPU*抏th蔼
ethj                                           athτ″}蜁tuQ!I_PH俚A
                 SW穗x眾姴捠0 偮U0a1XL揤H(昭絙ooW藵乮n 1殨嵔nd## ?靴筭 i[XV
                                                                           褋拏倐0 ?j
Linux version 2.6.31--LSDK-9.2.0_U6.616 (tplink@localhost.localdomain) (gcc version 4.3.3 (GCC) ) #1 Fri Aug 30 09:14:34 CST 2013
Ram size passed from bootloader =64M
flash_size passed from bootloader = 4
CPU revision is: 00019750 (MIPS 74Kc)
cpu apb d0 ddr 400 ahb 200
Determined physical RAM map:
memory: 04000000 @ 00000000 (usable)
Zone PFN ranges:
  Normal   0x00000000 -> 0x00004000
Movable zone start PFN for each node
early_node_map[1] active PFN ranges
    0: 0x00000000 -> 0x00004000
Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 16256
Kernel command line: console=ttyS0,115200 root=31:02 rootfstype=squashfs init=/sbin/init mtdparts=ath-nor0:128k(u-boot),1024k(kernel),2816k(rootfs),64k(config),64k(ART) mem=32M
PID hash table entries: 256 (order: 8, 1024 bytes)
Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes
Writing ErrCtl register=00000000
Readback ErrCtl register=00000000
Memory: 56500k/65536k available (1634k kernel code, 8968k reserved, 403k data, 116k init, 0k highmem)
NR_IRQS:128
plat_time_init: plat time init done
Calibrating delay loop... 359.42 BogoMIPS (lpj=718848)
Mount-cache hash table entries: 512

****************ALLOC***********************
Packet mem: 8022e3a0 (0x600000 bytes)
********************************************

NET: Registered protocol family 16
ath_pcibios_init: bus 0
***** Warning PCIe 0 H/W not found !!!
registering PCI controller with io_ma
Reset button pressed.
bio: create slab <bio-0> at 0
NET: Registered protocol family 2
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
TCP established hash table entries: 2048 (order: 2, 16384 bytes)
TCP bind hash table entries: 2048 (order: 1, 8192 bytes)
TCP: Hash tables configured (established 2048 bind 2048)
TCP reno registered
NET: Registered protocol family 1
ATH GPIOC major 0
squashfs: version 4.0 (2009/01/31) Phillip Lougher
msgmni has been set to 110
io scheduler noop registered
io scheduler deadline registered (default)
Serial: 8250/16550 driver, 1 ports, IRQ sharing disabled
serial8250.0: ttyS0 at MMIO 0xb8020000 (irq = 19) is a 16550A
console [ttyS0] enabled
PPP generic driver version 2.4.2
NET: Registered protocol family 24
5 cmdlinepart partitions found on MTD device ath-nor0
Creating 5 MTD partitions on "ath-nor0":
0x000000000000-0x000000020000 : "u-boot"
0x000000020000-0x000000120000 : "kernel"
0x000000120000-0x0000003e0000 : "rootfs"
0x0000003e0000-0x0000003f0000 : "config"
0x0000003f0000-0x000000400000 : "ART"
->Oops: flash id 0x10215 .
Ooops, why the devices couldn't been initialed?
TCP cubic registered
NET: Registered protocol family 17
802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>
All bugs added by David S. Miller <davem@redhat.com>
athwdt_init: Registering WDT success
ath_otp_init: Registering OTP sVFS: Mounted root (squashfs filesystem) readonly on device 31:2.
Freeing unused kernel memory: 116k freed
init started:  BusyBox v1.01 (2013.08.30-01:19+0000) multi-call binary
This Board use 2.6.31
xt_time: kernel timezone is -0000
nf_conntrack version 0.5.0 (1024 buckets, 8192 max)
CONFIG_NF_CT_ACCT is deprecated and will be removed soon. Please use
nf_co acct=1 nf_conntrack module option or
sysctl net.netfilter.nf_conntrack_acct=1 to enable it.
ip_tables: (C) 2000-2006 Netfilter Core Team
insmod: cannot open module `/lib/modules/2.6.31/kernel/iptable_raw.ko': No such file or directory
insmod: cannot open module `/lib/modules/2.6.31/kernel/flashid.ko': No such file or directory
PPPoL2TP kernel driver, V1.0
PPTP driver version 0.8.3
insmod: cannot open module `/lib/modules/2.6.31/kernel/harmony.ko': No such file or directory

qca955x_GMAC: Length per segment 1536
955x_GMAC: qca955x_gmac_attach
955x_GMAC: qca955x_set_gmac_caps
Currently in polling mode unit0
mac:0 Registering S27....
qca955x_GMAC: RX TASKLET - Pkts per Intr:100
qca955x_GMAC: Max segments per packet :   1
qca955x_GMAC: Max tx descriptor count :   192
qca955x_GMAC: Max rx descriptor count :   192
qca955x_GMAC: Mac capability flags    :   2200
(none) mips #1 Fri Aug 30 09:14:34 CST 2013 (none)
(none) login: athr_gmac_ring_alloc Allocated 3072 at 0x8393b000
athr_gmac_ring_alloc Allocated 3072 at 0x83a7c000
955x_GMAC: eth0 in MII MODE

######## S26 SSDK init succeeded! ########
ATHRS27: resetting s27
ATHRS27: s27 reset done
Setting Drop CRC Errors, Pause Frames and Length Error frames
Setting PHY...
device eth0.1 entered promiscuous mode
device eth0 entered promiscuous mode
device eth0 left promiscuous mode
device eth0 entered promiscuous mode
br0: port 1(eth0.1) entering forwarding state
nf_conntrack_rtsp v0.6.21 loading
nf_nat_rtsp v0.6.21 loading
adf: module license 'Proprietary' taints kernel.
Disabling lock debugging due to kernel taint
ath_hal: 0.9.17.1 (AR5416, AR9380, REGOPS_FUNC, WRITE_EEPROM, 11D)
ath_rate_atheros: Copyright (c) 2001-2005 Atheros Communications, Inc, All Rights Reserved
ath_dfs: Version 2.0.0
Copyright (c) 2005-2006 Atheros Communications, Inc. All Rights Reserved
ath_dev: Copyright (c) 2001-2007 Atheros Communications, Inc, All Rights Reserved
ath_ahb: 9.5.1.8 (Atheros/multi-bss)
Enterprise mode: 0x43fc0000
Restoring Cal data from Flash
ath_get_caps[5790] rx chainmask mismatch actual 7 sc_chainmak 0
ath_get_caps[5765] tx chainmask mismatch actual 7 sc_chainmak 0
dfs is NULL dfs_init_radar_filters
VAP device ath0 created

DES SSID SET=TP-LINK_4A644E
ieee80211_ioctl_siwmode: imr.ifm_active=131712, new mode=3, valid=1
NF Cal completed
NF Cal completed
Channel 1 average beacon RSSI 0 noisefloor -108  ieee80211_acs_find_best_11ng_centerchan chan: 1 beacon RSSI + weighted noisefloor: -216
Channel 6 average beacon RSSI 9 noisefloor -108  ieee80211_acs_find_best_11ng_centerchan chan: 6 beacon RSSI + weighted noisefloor: -207
Channel 6 average beacon RSSI 9 noisefloor -108  ieee80211_acs_find_best_11ng_centerchan chan: 6 beacon RSSI + weighted noisefloor: -207
Channel 11 average beacon RSSI 3 noisefloor -109  ieee80211_acs_find_best_11ng_centerchan chan: 11 beacon RSSI + weighted noisefloor: -215
ieee80211_acs_find_best_11ng_centerchan found best 11ng center chan: 1 rssi: -216
NF Cal completed
device ath0 entered promiscuous mode
br0: port 2(ath0) entering forwarding state
ieee80211_ioctl_siwmode: imr.ifm_active=918144, new mode=3, valid=1
br0: port 2(ath0) entering disabled state
DEVICE IS DOWN ifname=ath0
DEVICE IS DOWN ifname=ath0
br0: port 2(ath0) entering forwarding state
br0: port 2(ath0) entering disabled state
br0: starting userspace STP failed, starting kernel STP
br0: topology change detected, propagating
br0: port 2(ath0) entering forwarding state
Set phy 0 auto negotiation mode.


走到这里就不动了，按CTRL+C，tpl等没反应，按啥也没反应，
怎么个情况？

zli***

前面一段还是乱码。

jero***

这是什么鬼

zli***

重复

zli***

没人知道啥问题吗，
难道要求编程器固件么？

也没找到有编程器固件啊，
要不就自己打造编程器固件？

“直接打造完整的编程器固件写入，方便多了。 于是乎。。。。步骤：   1。winhex  新建一个8M的空白文件<未命名>， 文件-新建，建立新文件，文件大小输入 8MB 。 编辑-全选，填充选块，填充十六进制数值 FF 。  2。打开 WR841N V7 8MB u-boot.bin   编辑-全选， 复制。切换到刚建立的8M文件，编辑-写入，偏移地址0。   3。打开备份的固件，  位置-转到偏移量 1FC00 和 1FE00  处，填入新建立的8M文件对应位置。 定义选块 3F0000 - 3FFFFF， 复制，写入8M文件的偏移地址 7F1000 处。       原固件0x1FC00是你的MAC地址，0x1FE00是你的PIN，一般外壳背面写有。     原固件0x3F0000 - 0x3FFFFF，board_config/art 分区，包含无线部分校正数据（好像是各机不相同，否则会丢无线）  4。打开下载的固件， openwrt-ar71xx-generic-tl-mr3420-v1-squashfs-factory.bin 全选，复制，写入8M文件的偏移地址 0x20000 处。 保存文件， 8M 完整编程器固件就生成了，  写入flash
，起动即可

。”

按类似操作这样可以吗？
等编程器到了试试。。

zli***

波特率改为117600，没乱码了，但还是按不出中断，
ctrl+c和tpl都不行



U-Boot 1.1.4 (Aug 30 2013 - 09:09:22)

ap135 - Scorpion 1.0DRAM:  
sri
Scorpion 1.0
ath_ddr_initial_config(211): (16bit) ddr1 init
tap = 0x00000002
Tap (low, high) = (0x3, 0x33)
Tap values = (0x1b, 0x1b, 0x1b, 0x1b)
64 MB
Flash Manuf Id 0x1, DeviceId0 0x2, DeviceId1 0x15
flash size 4MB, sector count = 64
Flash:  4 MB
Using default environment

*** Warning *** : PCIe WLAN Module not found !!!
*** Warning *** : PCIe WLAN Module not found !!!
In:    serial
Out:   serial
Err:   serial
Net:   ath_gmac_enet_initialize...
No valid address in Flash. Using fixed address
ath_gmac_enet_initialize: reset mask:c02200
Scorpion ---->S27 PHY*
S27 reg init
ATHRS27: resetting s27
ATHRS27: s27 reset done
ATHRS27:REG 0x4-->:400
ATHRS27:REG 0x2c-->:7e3e003e
ATHRS27:REG 0x8-->:0
ATHRS27:REG 0xc-->:0
ATHRS27:REG 0x10-->:1061b20
: cfg1 0x80000000 cfg2 0x7114
eth0: ba:be:fa:ce:08:41
athrs27_phy_setup ATHR_PHY_CONTROL 0 :1000
athrs27_phy_setup ATHR_PHY_SPEC_STAUS 0 :10
athrs27_phy_setup ATHR_PHY_CONTROL 1 :1000
athrs27_phy_setup ATHR_PHY_SPEC_STAUS 1 :10
athrs27_phy_setup ATHR_PHY_CONTROL 2 :1000
athrs27_phy_setup ATHR_PHY_SPEC_STAUS 2 :10
athrs27_phy_setup ATHR_PHY_CONTROL 3 :1000
athrs27_phy_setup ATHR_PHY_SPEC_STAUS 3 :10
athrs27_phy_setup ATHR_PHY_CONTROL 4 :1000
athrs27_phy_setup ATHR_PHY_SPEC_STAUS 4 :10
eth0 up
eth0
Setting 0x18116290 to 0x50a1a14f
Autobooting in 1 seconds
## Booting image at 9f020000 ...
   Uncompressing Kernel Image ... OK

Starting kernel ...

Booting QCA955x
Linux version 2.6.31--LSDK-9.2.0_U6.616 (tplink@localhost.localdomain) (gcc version 4.3.3 (GCC) ) #1 Fri Aug 30 09:14:34 CST 2013
Ram size passed from bootloader =64M
flash_size passed from bootloader = 4
CPU revision is: 00019750 (MIPS 74Kc)
cpu apb ddr apb ath_sys_frequency: cpu 720 ddr 400 ahb 200
Determined physical RAM map:
memory: 04000000 @ 00000000 (usable)
Zone PFN ranges:
  Normal   0x00000000 -> 0x00004000
Movable zone start PFN for each node
early_node_map[1] active PFN ranges
    0: 0x00000000 -> 0x00004000
Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 16256
Kernel command line: console=ttyS0,115200 root=31:02 rootfstype=squashfs init=/sbin/init mtdparts=ath-nor0:128k(u-boot),1024k(kernel),2816k(rootfs),64k(config),64k(ART) mem=32M
PID hash table entries: 256 (order: 8, 1024 bytes)
Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes
Writing ErrCtl register=00000000
Readback ErrCtl register=00000000
Memory: 56500k/65536k available (1634k kernel code, 8968k reserved, 403k data, 116k init, 0k highmem)
NR_IRQS:128
plat_time_init: plat time init done
Calibrating delay loop... 359.42 BogoMIPS (lpj=718848)
Mount-cache hash table entries: 512

****************ALLOC***********************
Packet mem: 8022e3a0 (0x600000 bytes)
********************************************

NET: Registered protocol family 16
ath_pcibios_init: bus 0
***** Warning PCIe 0 H/W not found !!!
registering PCI controller with io_map_base unset
ath_pcibios_init: bus 1
***** Warning PCIe 1 H/W not found !!!
registering PCI controller with io_map_base unset
Reset button pressed.
bio: create slab <bio-0> at 0
NET: Registered protocol family 2
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
TCP established hash table entries: 2048 (order: 2, 16384 bytes)
TCP bind hash table entries: 2048 (order: 1, 8192 bytes)
TCP: Hash tables configured (established 2048 bind 2048)
TCP reno registered
NET: Registered protocol family 1
ATH GPIOC major 0
squashfs: version 4.0 (2009/01/31) Phillip Lougher
msgmni has been set to 110
io scheduler noop registered
io scheduler deadline registered (default)
Serial: 8250/16550 driver, 1 ports, IRQ sharing disabled
serial8250.0: ttyS0 at MMIO 0xb8020000 (irq = 19) is a 16550A
console [ttyS0] enabled
PPP generic driver version 2.4.2
NET: Registered protocol family 24
5 cmdlinepart partitions found on MTD device ath-nor0
Creating 5 MTD partitions on "ath-nor0":
0x000000000000-0x000000020000 : "u-boot"
0x000000020000-0x000000120000 : "kernel"
0x000000120000-0x0000003e0000 : "rootfs"
0x0000003e0000-0x0000003f0000 : "config"
0x0000003f0000-0x000000400000 : "ART"
->Oops: flash id 0x10215 .
Ooops, why the devices couldn't been initialed?
TCP cubic registered
NET: Registered protocol family 17
802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>
All bugs added by David S. Miller <davem@redhat.com>
athwdt_init: Registering WDT success
ath_otp_init: Registering OTP success
VFS: Mounted root (squashfs filesystem) readonly on device 31:2.
Freeing unused kernel memory: 116k freed
init started:  BusyBox v1.01 (2013.08.30-01:19+0000) multi-call binary
This Board use 2.6.31
xt_time: kernel timezone is -0000
nf_conntrack version 0.5.0 (1024 buckets, 8192 max)
CONFIG_NF_CT_ACCT is deprecated and will be removed soon. Please use
nf_conntrack.acct=1 kernel parameter, acct=1 nf_conntrack module option or
sysctl net.netfilter.nf_conntrack_acct=1 to enable it.
ip_tables: (C) 2000-2006 Netfilter Core Team
insmod: cannot open module `/lib/modules/2.6.31/kernel/iptable_raw.ko': No such file or directory
insmod: cannot open module `/lib/modules/2.6.31/kernel/flashid.ko': No such file or directory
PPPoL2TP kernel driver, V1.0
PPTP driver version 0.8.3
insmod: cannot open module `/lib/modules/2.6.31/kernel/harmony.ko': No such file or directory

qca955x_GMAC: Length per segment 1536
955x_GMAC: qca955x_gmac_attach
955x_GMAC: qca955x_set_gmac_caps
Currently in polling mode unit0
mac:0 Registering S27....
qca955x_GMAC: RX TASKLET - Pkts per Intr:100
qca955x_GMAC: Max segments per packet :   1
qca955x_GMAC: Max tx descriptor count :   192
qca955x_GMAC: Max rx descriptor count :   192
qca955x_GMAC: Mac capability flags    :   2200
(none) mips #1 Fri Aug 30 09:14:34 CST 2013 (none)
(none) login: athr_gmac_ring_alloc Allocated 3072 at 0x8393b000
athr_gmac_ring_alloc Allocated 3072 at 0x83a61000
955x_GMAC: eth0 in MII MODE

######## S26 SSDK init succeeded! ########
ATHRS27: resetting s27
ATHRS27: s27 reset done
Setting Drop CRC Errors, Pause Frames and Length Error frames
Setting PHY...
device eth0.1 entered promiscuous mode
device eth0 entered promiscuous mode
device eth0 left promiscuous mode
device eth0 entered promiscuous mode
br0: port 1(eth0.1) entering forwarding state
nf_conntrack_rtsp v0.6.21 loading
nf_nat_rtsp v0.6.21 loading
adf: module license 'Proprietary' taints kernel.
Disabling lock debugging due to kernel taint
ath_hal: 0.9.17.1 (AR5416, AR9380, REGOPS_FUNC, WRITE_EEPROM, 11D)
ath_rate_atheros: Copyright (c) 2001-2005 Atheros Communications, Inc, All Rights Reserved
ath_dfs: Version 2.0.0
Copyright (c) 2005-2006 Atheros Communications, Inc. All Rights Reserved
ath_dev: Copyright (c) 2001-2007 Atheros Communications, Inc, All Rights Reserved
ath_ahb: 9.5.1.8 (Atheros/multi-bss)
Enterprise mode: 0x43fc0000
Restoring Cal data from Flash
ath_get_caps[5790] rx chainmask mismatch actual 7 sc_chainmak 0
ath_get_caps[5765] tx chainmask mismatch actual 7 sc_chainmak 0
SC Callback Registration for wifi0
wifi0: Atheros ???: mem=0xb8100000, irq=2
dfs is NULL dfs_init_radar_filters
VAP device ath0 created

DES SSID SET=TP-LINK_4A644E
ieee80211_ioctl_siwmode: imr.ifm_active=131712, new mode=3, valid=1
NF Cal completed
NF Cal completed
Channel 1 average beacon RSSI 0 noisefloor -109  ieee80211_acs_find_best_11ng_centerchan chan: 1 beacon RSSI + weighted noisefloor: -218
Channel 6 average beacon RSSI 9 noisefloor -109  ieee80211_acs_find_best_11ng_centerchan chan: 6 beacon RSSI + weighted noisefloor: -209
Channel 6 average beacon RSSI 9 noisefloor -109  ieee80211_acs_find_best_11ng_centerchan chan: 6 beacon RSSI + weighted noisefloor: -209
Channel 11 average beacon RSSI 0 noisefloor -108  ieee80211_acs_find_best_11ng_centerchan chan: 11 beacon RSSI + weighted noisefloor: -216
ieee80211_acs_find_best_11ng_centerchan found best 11ng center chan: 1 rssi: -218
NF Cal completed
device ath0 entered promiscuous mode
br0: port 2(ath0) entering forwarding state
ieee80211_ioctl_siwmode: imr.ifm_active=918144, new mode=3, valid=1
br0: port 2(ath0) entering disabled state
DEVICE IS DOWN ifname=ath0
DEVICE IS DOWN ifname=ath0
br0: port 2(ath0) entering forwarding state
br0: port 2(ath0) entering disabled state
br0: starting userspace STP failed, starting kernel STP
br0: topology change detected, propagating
br0: port 2(ath0) entering forwarding state
Set phy 0 auto negotiation mode.

前***

有编程器固件吗？