|
|
自己刷了一遍bread 现在情况是插网线 完全不会dhcp分配给ip 自己手动设置ip也进不去bread和op
用ttl链接 发现启动的时候可以进入bread 并且有提示中断，但是中断之后插网线照样进不去bread
任其启动 发现op也可以进去，但是插网线一样不会分配ip 手动设置ip也不可以 现在不知道为什么了！烦请各位老大哥来看看！ 谢谢！！ 型号 TP-wdr4320 固件 明月op u-boot是bread
下面附上终端情况
——————————————————————————————————————————————————————————————————————————————————————————
breed>
breed> reset
Resetting ...
Boot and Recovery Environment for Embedded Devices
Copyright (C) 2017 HackPascal <hackpascal@gmail.com>
Build date 2017-04-16 [git-47a2563]
Version 1.1 (r1010)
DRAM: 128MB
Platform: Atheros AR9344 rev 2
Board: Atheros DB120 reference board
Clocks: CPU: 560MHz, DDR: 450MHz, AHB: 225MHz, Ref: 40MHz
Flash: Winbond W25Q128 (16MB) on ath79-spi.0
ag71xx-eth: MAC address is invalid, using default settings.
ag71xx-eth: Using MAC address 00:13:74:00:00:01
Waiting for auto-negotiation complete ... OK
eth0: Atheros AR8327/AR8328 rev 2
Network started on eth0, inet addr 192.168.1.1, netmask 255.255.255.0
Press any key to interrupt autoboot ... 3
Autoboot aborted due to key press.
Starting breed built-in shell
breed>
breed> help
Available commands:
about - About this bootloader
abstatus - Interrupt status of autoboot
arp - Display ARP table
autoboot - Detect firmware type and boot automatically
boot - Boot firmware
btntst - Test GPIO of buttons
dhcp - Display DHCP leases
env - Environment variables utility
envconf - Configure environment variable block
exit - Exit from telnet
flash - Flash utility
gpio - GPIO utilities
help - Show available commands
mdio - MDIO utility
mem - Memory operation utilities
net - Network control
netstat - Display network state
reset - Restart device
setbrg - Set baudrate
sysinfo - Display system information
thread - Display all threads
wget - Retrieval file through HTTP
breed> dhcp
IP address MAC address
breed> dhcp mac
breed> dhcp ip
breed> dhcp
IP address MAC address
breed> dhcp ip address
breed> reset
Resetting ...
Boot and Recovery Environment for Embedded Devices
Copyright (C) 2017 HackPascal <hackpascal@gmail.com>
Build date 2017-04-16 [git-47a2563]
Version 1.1 (r1010)
DRAM: 128MB
Platform: Atheros AR9344 rev 2
Board: Atheros DB120 reference board
Clocks: CPU: 560MHz, DDR: 450MHz, AHB: 225MHz, Ref: 40MHz
Flash: Winbond W25Q128 (16MB) on ath79-spi.0
ag71xx-eth: MAC address is invalid, using default settings.
ag71xx-eth: Using MAC address 00:13:74:00:00:01
Waiting for auto-negotiation complete ... OK
eth0: Atheros AR8327/AR8328 rev 2
Network started on eth0, inet addr 192.168.1.1, netmask 255.255.255.0
Press any key to interrupt autoboot ... 3
Autoboot aborted due to key press.
Starting breed built-in shell
breed> autoboot
Trying to boot firmware from 0x9f020000 ...
TP-LINK firmware image header detected.
Image Name: 43100001
Data Size: 1149652 Bytes
Load Address: 80060000
Entry Point: 80060000
Uncompressing data (LZMA) ... done.
Flushing cache ... done.
Starting kernel at 0x80060000...
[ 0.000000] Linux version 3.18.21 (rapistor@rapistor-Ubuntu) (gcc version 4.8 .3 (OpenWrt/Linaro GCC 4.8-2014.04 r47046) ) #2 Sun Sep 27 11:09:16 CST 2015
[ 0.000000] bootconsole [early0] enabled
[ 0.000000] CPU0 revision is: 0001974c (MIPS 74Kc)
[ 0.000000] SoC: Atheros AR9344 rev 2
[ 0.000000] Determined physical RAM map:
[ 0.000000] memory: 08000000 @ 00000000 (usable)
[ 0.000000] Initrd not found or empty - disabling initrd
[ 0.000000] Zone ranges:
[ 0.000000] Normal [mem 0x00000000-0x07ffffff]
[ 0.000000] Movable zone start for each node
[ 0.000000] Early memory node ranges
[ 0.000000] node 0: [mem 0x00000000-0x07ffffff]
[ 0.000000] Initmem setup node 0 [mem 0x00000000-0x07ffffff]
[ 0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
[ 0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pag es: 32512
[ 0.000000] Kernel command line: board=TL-WDR4300 console=ttyS0,115200 root fstype=squashfs,jffs2 noinitrd
[ 0.000000] PID hash table entries: 512 (order: -1, 2048 bytes)
[ 0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
[ 0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
[ 0.000000] Writing ErrCtl register=00000000
[ 0.000000] Readback ErrCtl register=00000000
[ 0.000000] Memory: 125856K/131072K available (2511K kernel code, 125K rwdata , 536K rodata, 276K init, 188K bss, 5216K reserved)
[ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[ 0.000000] NR_IRQS:51
[ 0.000000] Clocks: CPU:560.000MHz, DDR:450.000MHz, AHB:225.000MHz, Ref:40.00 0MHz
[ 0.000000] Calibrating delay loop... 278.93 BogoMIPS (lpj=1394688)
[ 0.070000] pid_max: default: 32768 minimum: 301
[ 0.070000] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.080000] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.090000] NET: Registered protocol family 16
[ 0.090000] MIPS: machine is TP-LINK TL-WDR4300
[ 0.100000] registering PCI controller with io_map_base unset
[ 0.330000] PCI host bridge to bus 0000:00
[ 0.330000] pci_bus 0000:00: root bus resource [mem 0x10000000-0x13ffffff]
[ 0.340000] pci_bus 0000:00: root bus resource [io 0x0000]
[ 0.340000] pci_bus 0000:00: No busn resource found for root bus, will use [b us 00-ff]
[ 0.350000] pci 0000:00:00.0: invalid calibration data
[ 0.350000] pci 0000:00:00.0: BAR 0: assigned [mem 0x10000000-0x1001ffff 64bi t]
[ 0.360000] pci 0000:00:00.0: BAR 6: assigned [mem 0x10020000-0x1002ffff pref ]
[ 0.360000] pci 0000:00:00.0: using irq 40 for pin 1
[ 0.370000] Switched to clocksource MIPS
[ 0.370000] NET: Registered protocol family 2
[ 0.380000] TCP established hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.380000] TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.390000] TCP: Hash tables configured (established 1024 bind 1024)
[ 0.400000] TCP: reno registered
[ 0.400000] UDP hash table entries: 256 (order: 0, 4096 bytes)
[ 0.400000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[ 0.410000] NET: Registered protocol family 1
[ 0.420000] futex hash table entries: 256 (order: -1, 3072 bytes)
[ 0.440000] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 0.440000] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORIT Y) (c) 2001-2006 Red Hat, Inc.
[ 0.450000] msgmni has been set to 245
[ 0.460000] io scheduler noop registered
[ 0.460000] io scheduler deadline registered (default)
[ 0.470000] Serial: 8250/16550 driver, 1 ports, IRQ sharing disabled
▒[ 0.500000] serial8250.0: ttyS0 at MMIO 0x18020000 (irq = 11, base_baud = 25 00000) is a 16550A
[ 0.510000] console [ttyS0] enabled
[ 0.510000] console [ttyS0] enabled
[ 0.520000] bootconsole [early0] disabled
[ 0.520000] bootconsole [early0] disabled
[ 0.530000] m25p80 spi0.0: found w25q128, expected m25p80
[ 0.530000] m25p80 spi0.0: w25q128 (16384 Kbytes)
[ 0.540000] 6 tp-link partitions found on MTD device spi0.0
[ 0.540000] Creating 6 MTD partitions on "spi0.0":
[ 0.550000] 0x000000000000-0x000000020000 : "u-boot"
[ 0.550000] 0x000000020000-0x000000138cd4 : "kernel"
[ 0.560000] 0x000000138cd4-0x000000ff0000 : "rootfs"
[ 0.560000] mtd: device 2 (rootfs) set to be root filesystem
[ 0.570000] 1 squashfs-split partitions found on MTD device rootfs
[ 0.580000] 0x000000d90000-0x000000ff0000 : "rootfs_data"
[ 0.580000] 0x000000ff0000-0x000001000000 : "art"
[ 0.590000] 0x000000020000-0x000000ff0000 : "firmware"
[ 0.590000] 0x000000000000-0x000001000000 : "fullflash"
[ 0.610000] switch0: Atheros AR8327 rev. 2 switch registered on ag71xx-mdio.0
[ 0.680000] libphy: ag71xx_mdio: probed
[ 1.280000] ag71xx ag71xx.0: connected to PHY at ag71xx-mdio.0:00 [uid=004dd0 33, driver=Atheros AR8216/AR8236/AR8316]
[ 1.290000] eth0: Atheros AG71xx at 0xb9000000, irq 4, mode:RGMII
[ 1.300000] TCP: cubic registered
[ 1.300000] NET: Registered protocol family 17
[ 1.300000] bridge: automatic filtering via arp/ip/ip6tables has been depreca ted. Update your scripts to load br_netfilter if you need this.
[ 1.320000] Bridge firewalling registered
[ 1.320000] 8021q: 802.1Q VLAN Support v1.8
[ 1.330000] VFS: Mounted root (squashfs filesystem) readonly on device 31:2.
[ 1.340000] Freeing unused kernel memory: 276K (8037b000 - 803c0000)
[ 3.110000] init: Console is alive
[ 3.120000] init: - watchdog -
[ 6.660000] usbcore: registered new interface driver usbfs
[ 6.670000] usbcore: registered new interface driver hub
[ 6.670000] usbcore: registered new device driver usb
[ 6.690000] exFAT: Version 1.2.9
[ 6.730000] SCSI subsystem initialized
[ 6.740000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 6.750000] ehci-platform: EHCI generic platform driver
[ 6.750000] ehci-platform ehci-platform: EHCI Host Controller
[ 6.760000] ehci-platform ehci-platform: new USB bus registered, assigned bus number 1
[ 6.770000] ehci-platform ehci-platform: irq 3, io mem 0x1b000000
[ 6.790000] ehci-platform ehci-platform: USB 2.0 started, EHCI 1.00
[ 6.790000] hub 1-0:1.0: USB hub found
[ 6.800000] hub 1-0:1.0: 1 port detected
[ 6.800000] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[ 6.810000] ohci-platform: OHCI generic platform driver
[ 6.820000] uhci_hcd: USB Universal Host Controller Interface driver
[ 6.830000] usbcore: registered new interface driver usb-storage
[ 7.120000] usb 1-1: new high-speed USB device number 2 using ehci-platform
[ 7.270000] hub 1-1:1.0: USB hub found
[ 7.270000] hub 1-1:1.0: 4 ports detected
[ 7.450000] init: - preinit -
[ 8.430000] random: procd urandom read with 14 bits of entropy available
Press the [f] key and hit [enter] to enter failsafe mode
Press the [1], [2], [3] or [4] key and hit [enter] to select the debug level
[ 9.760000] eth0: link up (1000Mbps/Full duplex)
[ 11.840000] mount_root: loading kmods from internal overlay
[ 12.240000] jffs2: notice: (409) jffs2_build_xattr_subsystem: complete buildi ng xattr subsystem, 0 of xdatum (0 unchecked, 0 orphan) and 0 of xref (0 dead, 0 orphan) found.
[ 12.260000] block: attempting to load /tmp/jffs_cfg/upper/etc/config/fstab
[ 12.280000] block: extroot: not configured
[ 12.320000] jffs2: notice: (406) jffs2_build_xattr_subsystem: complete buildi ng xattr subsystem, 0 of xdatum (0 unchecked, 0 orphan) and 0 of xref (0 dead, 0 orphan) found.
[ 12.340000] mount_root: loading kmods from internal overlay
[ 12.530000] block: attempting to load /tmp/jffs_cfg/upper/etc/config/fstab
[ 12.540000] block: extroot: not configured
[ 12.540000] mount_root: switching to jffs2 overlay
[ 12.590000] eth0: link down
[ 12.600000] procd: - early -
[ 12.600000] procd: - watchdog -
[ 13.760000] procd: - ubus -
[ 14.780000] procd: - init -
Please press Enter to activate this console.
[ 21.530000] NET: Registered protocol family 10
[ 21.550000] NET: Registered protocol family 8
[ 21.560000] NET: Registered protocol family 20
[ 21.640000] tun: Universal TUN/TAP device driver, 1.6
[ 21.650000] tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
[ 21.670000] ufsd: module license 'Commercial product' taints kernel.
[ 21.670000] Disabling lock debugging due to kernel taint
[ 21.710000] ufsd: driver (lke_8.9.0 lke_8.9.0_r217400_b3, LBD=ON, delalloc, i octl, sd2(1), fua) loaded at 86000000
[ 21.710000] NTFS support included
[ 21.710000] Big endian platform
[ 21.710000] optimized: speed
[ 21.710000] Build_for__ASUS_PRODUCTS_005_k2.6.22.15_2013-11-20_lke_8.9.0_r217 400_b3
[ 21.710000]
[ 21.760000] l2tp_core: L2TP core driver, V2.0
[ 21.770000] l2tp_netlink: L2TP netlink interface
[ 21.780000] sit: IPv6 over IPv4 tunneling driver
[ 21.790000] gre: GRE over IPv4 demultiplexor driver
[ 21.790000] ip_gre: GRE over IPv4 tunneling driver
[ 21.800000] PPP generic driver version 2.4.2
[ 21.820000] ip6_tables: (C) 2000-2006 Netfilter Core Team
[ 21.870000] nf_conntrack version 0.5.0 (1970 buckets, 7880 max)
[ 21.970000] Netfilter messages via NETLINK v0.30.
[ 21.990000] ip_set: protocol 6
[ 22.440000] Linux video capture interface: v2.00
[ 22.610000] u32 classifier
[ 22.610000] input device check on
[ 22.610000] Actions configured
[ 22.640000] Mirror/redirect action on
[ 22.950000] fuse init (API version 7.23)
[ 23.000000] arp_tables: (C) 2002 David S. Miller
[ 23.010000] usbcore: registered new interface driver cdc_acm
[ 23.020000] cdc_acm: USB Abstract Control Model driver for USB modems and ISD N adapters
[ 23.030000] Loading modules backported from Linux version master-2015-03-09-0 -g141f155
[ 23.040000] Backport generated by backports.git backports-20150129-0-gdd4a670
[ 23.050000] cpia2: V4L-Driver for Vision CPiA2 based cameras v3.0.1
[ 23.060000] usbcore: registered new interface driver cpia2
[ 23.100000] Ebtables v2.0 registered
[ 23.110000] Hooked IMQ after mangle on PREROUTING
[ 23.110000] Hooked IMQ after nat on POSTROUTING
[ 23.120000] IMQ driver loaded successfully. (numdevs = 2, numqueues = 1)
[ 23.120000] Hooking IMQ before NAT on PREROUTING.
[ 23.130000] Hooking IMQ after NAT on POSTROUTING.
[ 23.160000] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 23.270000] PPP MPPE Compression module registered
[ 23.280000] NET: Registered protocol family 24
[ 23.290000] p p t p driver version 0.8.5
[ 23.320000] usbcore: registered new interface driver ums-alauda
[ 23.330000] usbcore: registered new interface driver ums-cypress
[ 23.340000] usbcore: registered new interface driver ums-datafab
[ 23.350000] usbcore: registered new interface driver ums-freecom
[ 23.360000] usbcore: registered new interface driver ums-isd200
[ 23.370000] usbcore: registered new interface driver ums-jumpshot
[ 23.380000] usbcore: registered new interface driver ums-karma
[ 23.390000] usbcore: registered new interface driver ums-sddr09
[ 23.580000] usbcore: registered new interface driver ums-sddr55
[ 23.600000] usbcore: registered new interface driver ums-usbat
[ 23.610000] usbcore: registered new interface driver usblp
[ 23.630000] usbcore: registered new interface driver usbserial
[ 23.630000] usbcore: registered new interface driver usbserial_generic
[ 23.640000] usbserial: USB Serial support registered for generic
[ 23.670000] usbcore: registered new interface driver uvcvideo
[ 23.670000] USB Video Class driver (1.1.1)
[ 23.780000] xt_time: kernel timezone is -0000
[ 23.850000] cfg80211: Calling CRDA to update world regulatory domain
[ 23.900000] gspca_main: v2.14.0 registered
[ 23.900000] cfg80211: World regulatory domain updated:
[ 23.910000] cfg80211: DFS Master region: unset
[ 23.910000] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gai n, max_eirp), (dfs_cac_time)
[ 23.920000] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A, 3000 m Bm), (N/A)
[ 23.930000] cfg80211: (2457000 KHz - 2482000 KHz @ 40000 KHz), (N/A, 3000 m Bm), (N/A)
[ 23.940000] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (N/A, 3000 m Bm), (N/A)
[ 23.950000] cfg80211: (5170000 KHz - 5250000 KHz @ 80000 KHz), (N/A, 4000 m Bm), (N/A)
[ 23.960000] cfg80211: (5250000 KHz - 5330000 KHz @ 80000 KHz, 160000 KHz AU TO), (N/A, 4000 mBm), (0 s)
[ 23.960000] cfg80211: (5490000 KHz - 5730000 KHz @ 160000 KHz), (N/A, 4000 mBm), (0 s)
[ 23.970000] cfg80211: (5735000 KHz - 5835000 KHz @ 80000 KHz), (N/A, 4000 m Bm), (N/A)
[ 23.980000] cfg80211: (57240000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 0 mBm), (N/A)
[ 24.000000] usbcore: registered new interface driver vc032x
[ 24.030000] usbcore: registered new interface driver gspca_zc3xx
[ 24.040000] l2tp_ppp: PPPoL2TP kernel driver, V2.0
[ 24.210000] usbcore: registered new interface driver pl2303
[ 24.220000] usbserial: USB Serial support registered for pl2303
[ 24.280000] usbcore: registered new interface driver rt73usb
[ 24.290000] usbcore: registered new interface driver rtl8187
[ 24.350000] usbcore: registered new interface driver snd-usb-audio
[ 24.460000] usbcore: registered new interface driver option
[ 24.470000] usbserial: USB Serial support registered for GSM modem (1-port)
[ 24.500000] usbcore: registered new interface driver rt2800usb
[ 24.600000] usbcore: registered new interface driver ath9k_htc
[ 24.610000] usbcore: registered new interface driver rtl8192cu
[ 24.670000] ieee80211 phy0: Atheros AR9340 Rev:2 mem=0xb8100000, irq=47
[ 24.690000] ieee80211 phy1: Atheros AR9300 Rev:4 mem=0xb0000000, irq=40
[ 24.700000] cfg80211: Calling CRDA for country: US
[ 24.700000] cfg80211: Regulatory domain changed to country: US
[ 24.710000] cfg80211: DFS Master region: FCC
[ 24.710000] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gai n, max_eirp), (dfs_cac_time)
[ 24.720000] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A, 3000 m Bm), (N/A)
[ 24.730000] cfg80211: (5170000 KHz - 5250000 KHz @ 80000 KHz, 160000 KHz AU TO), (N/A, 3000 mBm), (N/A)
[ 24.740000] cfg80211: (5250000 KHz - 5330000 KHz @ 80000 KHz, 160000 KHz AU TO), (N/A, 3000 mBm), (0 s)
[ 24.750000] cfg80211: (5735000 KHz - 5835000 KHz @ 80000 KHz), (N/A, 4000 m Bm), (N/A)
[ 24.760000] cfg80211: (57240000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 40 00 mBm), (N/A)
[ 37.000000] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 37.000000] device eth0.1 entered promiscuous mode
[ 37.010000] device eth0 entered promiscuous mode
[ 37.030000] IPv6: ADDRCONF(NETDEV_UP): br-lan: link is not ready
[ 37.060000] IPv6: ADDRCONF(NETDEV_UP): eth0.2: link is not ready
[ 38.910000] eth0: link up (1000Mbps/Full duplex)
[ 38.950000] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[ 38.950000] cfg80211: Calling CRDA for country: CN
[ 38.990000] br-lan: port 1(eth0.1) entered forwarding state
[ 38.990000] br-lan: port 1(eth0.1) entered forwarding state
[ 39.000000] IPv6: ADDRCONF(NETDEV_CHANGE): eth0.2: link becomes ready
[ 39.010000] cfg80211: Regulatory domain changed to country: CN
[ 39.010000] cfg80211: DFS Master region: FCC
[ 39.020000] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gai n, max_eirp), (dfs_cac_time)
[ 39.030000] cfg80211: (2402000 KHz - 2482000 KHz @ 40000 KHz), (N/A, 3000 m Bm), (N/A)
[ 39.040000] cfg80211: (5170000 KHz - 5250000 KHz @ 80000 KHz, 160000 KHz AU TO), (N/A, 3000 mBm), (N/A)
[ 39.040000] cfg80211: (5250000 KHz - 5330000 KHz @ 80000 KHz, 160000 KHz AU TO), (N/A, 300 mBm), (0 s)
[ 39.050000] cfg80211: (5735000 KHz - 5835000 KHz @ 80000 KHz), (N/A, 4000 m Bm), (N/A)
[ 39.060000] cfg80211: (57240000 KHz - 59400000 KHz @ 2160000 KHz), (N/A, 28 00 mBm), (N/A)
[ 39.070000] cfg80211: (59400000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 44 00 mBm), (N/A)
[ 39.080000] cfg80211: (63720000 KHz - 65880000 KHz @ 2160000 KHz), (N/A, 28 00 mBm), (N/A)
[ 39.120000] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready
[ 40.990000] br-lan: port 1(eth0.1) entered forwarding state
[ 41.610000] Atheros AR8216/AR8236/AR8316 ag71xx-mdio.0:00: Port 2 is up
[ 73.610000] random: nonblocking pool is initialized
BusyBox v1.23.2 (2015-09-27 09:55:13 CST) built-in shell (ash)
_______ ________ __
| |.-----.-----.-----.| | | |.----.| |_
| - || _ | -__| || | | || _|| _|
|_______|| __|_____|__|__||________||__| |____|
|__| W I R E L E S S F R E E D O M
-----------------------------------------------------
CHAOS CALMER (Chaos Calmer, r47046)
-----------------------------------------------------
* 1 1/2 oz Gin Shake with a glassful
* 1/4 oz Triple Sec of broken ice and pour
* 3/4 oz Lime Juice unstrained into a goblet.
* 1 1/2 oz Orange Juice
* 1 tsp. Grenadine Syrup
* This firmware is compiled by rapistor(明月永在). QQ 273584038
-----------------------------------------------------
root@OpenWrt:/#
root@OpenWrt:/#
root@OpenWrt:/# show ?
/bin/ash: show: not found
root@OpenWrt:/# help
/bin/ash: help: not found
root@OpenWrt:/# /help
/bin/ash: /help: not found
root@OpenWrt:/# help
/bin/ash: help: not found
root@OpenWrt:/# /?
/bin/ash: /?: not found
root@OpenWrt:/# ?
/bin/ash: ?: not found
root@OpenWrt:/# [ 159.300000] Atheros AR8216/AR8236/AR8316 ag71xx-mdio.0:00: Port 2 is down
root@OpenWrt:/#
————————————————————————————————————————————————————————————————
已经无能为力了暂时，麻烦路过的各位大大了！
|
|
/1 
IP卡
狗仔卡
发表于 2017-4-27 18:21
置顶卡
沉默卡
喧嚣卡
顶贴卡
显身卡