mi424wr ixp533M 终极改造。

qwea

今天化了2个多小时飞线。完成了我的mi424的终极改造。

Uncompressing Linux....................................................................... done, booting the kernel.
Linux version 2.6.28.10 (openwrt@openwrt-desktop) (gcc version 4.4.0 (GCC) ) #5 Sat May 16 20:40:14 CST 2009
CPU: XScale-IXP42x Family [690541c1] revision 1 (ARMv5TE), cr=000039ff
CPU: VIVT data cache, VIVT instruction cache
Machine: Actiontec MI424WR
Memory policy: ECC disabled, Data cache writeback
Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 32512
Kernel command line: root=/dev/mtdblock2 rootfstype=squashfs,jffs2 noinitrd console=ttyS0,115200
PID hash table entries: 512 (order: 9, 2048 bytes)
Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
Memory: 128MB = 128MB total
Memory: 127560KB available (1964K code, 183K data, 96K init)
Calibrating delay loop... 532.48 BogoMIPS (lpj=2662400)
Mount-cache hash table entries: 512
CPU: Testing write buffer coherency: ok
net_namespace: 480 bytes
NET: Registered protocol family 16
IXP4xx: Using 16MiB expansion bus window size
PCI: IXP4xx is host
PCI: IXP4xx Using direct access for memory space
pci 0000:00:0f.0: PME# supported from D0 D1 D2 D3hot
pci 0000:00:0f.0: PME# disabled
pci 0000:00:0f.1: PME# supported from D0 D1 D2 D3hot
pci 0000:00:0f.1: PME# disabled
pci 0000:00:0f.2: PME# supported from D0 D1 D2 D3hot
pci 0000:00:0f.2: PME# disabled
PCI: bus0: Fast back to back transfers disabled
pci 0000:00:0d.0: dmabounce: registered device
pci 0000:00:0f.0: dmabounce: registered device
pci 0000:00:0f.1: dmabounce: registered device
pci 0000:00:0f.2: dmabounce: registered device
NET: Registered protocol family 2
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
TCP established hash table entries: 4096 (order: 3, 32768 bytes)
TCP bind hash table entries: 4096 (order: 2, 16384 bytes)
TCP: Hash tables configured (established 4096 bind 4096)
TCP reno registered
NET: Registered protocol family 1
IXP4xx Queue Manager initialized.
squashfs: version 3.0 (2006/03/15) Phillip Lougher
Registering mini_fo version $Id$
JFFS2 version 2.2. (NAND) (SUMMARY)  漏 2001-2006 Red Hat, Inc.
msgmni has been set to 249
io scheduler noop registered
io scheduler deadline registered (default)
Serial: 8250/16550 driver4 ports, IRQ sharing disabled
serial8250.0: ttyS0 at MMIO 0xc8000000 (irq = 15) is a XScale
console [ttyS0] enabled
serial8250.0: ttyS1 at MMIO 0xc8001000 (irq = 13) is a XScale
eth0: MII PHY 1 on NPE-C
eth0: MII PHY 2 on NPE-C
eth0: MII PHY 3 on NPE-C
eth0: MII PHY 4 on NPE-C
eth1: MII PHY 17 on NPE-B
IXP4XX-Flash.0: Found 1 x16 devices at 0x0 in 16-bit bank
Intel/Sharp Extended Query Table at 0x0031
Using buffer write method
cfi_cmdset_0001: Erase suspend on write enabled
Searching for RedBoot partition table in IXP4XX-Flash.0 at offset 0xfe0000
5 RedBoot partitions found on MTD device IXP4XX-Flash.0
Creating 5 MTD partitions on "IXP4XX-Flash.0":
0x00000000-0x00060000 : "RedBoot"
0x00060000-0x00180000 : "linux"
0x00180000-0x00fe0000 : "rootfs"
mtd: partition "rootfs" set to be root filesystem
mtd: partition "rootfs_data" created automatically, ofs=540000, len=AA0000
0x00540000-0x00fe0000 : "rootfs_data"
0x00fe0000-0x00fff000 : "FIS directory"
0x00fff000-0x01000000 : "RedBoot config"
i2c /dev entries driver
IXP4xx Watchdog Timer: heartbeat 60 sec
Registered led device: moca-wan
Registered led device: power-alarm
Registered led device: power-ok
Registered led device: wireless
Registered led device: inet-down
Registered led device: inet-up
Registered led device: moca-lan
Registered led device: wan-alarm
TCP westwood registered
NET: Registered protocol family 17
802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>
All bugs added by David S. Miller <davem@redhat.com>
XScale DSP coprocessor detected.
drivers/rtc/hctosys.c: unable to open rtc device (rtc0)
VFS: Mounted root (squashfs filesystem) readonly.
Freeing init memory: 96K
Please be patient, while OpenWrt loads ...
- preinit -
Press CTRL-C for failsafe
switching to jffs2
mini_fo: using base directory: /
mini_fo: using storage directory: /jffs
- init -

Please press Enter to activate this console. net eth0: firmware: requesting NPE-C
NPE-C: firmware's license can be found in /usr/share/doc/LICENSE.IPL
NPE-C: firmware functionality 0x5, revision 0x2:1
eth0: link down
device eth0 entered promiscuous mode
net eth1: firmware: requesting NPE-B
NPE-B: firmware's license can be found in /usr/share/doc/LICENSE.IPL
NPE-B: firmware functionality 0x2, revision 0x2:1
eth1: link down
eth1: link down
eth0: link up
br-lan: topology change detected, propagating
br-lan: port 1(eth0) entering forwarding state
cfg80211: Using static regulatory domain info
cfg80211: Regulatory domain: US
        (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
        (2402000 KHz - 2472000 KHz @ 40000 KHz), (600 mBi, 2700 mBm)
        (5170000 KHz - 5190000 KHz @ 40000 KHz), (600 mBi, 2300 mBm)
        (5190000 KHz - 5210000 KHz @ 40000 KHz), (600 mBi, 2300 mBm)
        (5210000 KHz - 5230000 KHz @ 40000 KHz), (600 mBi, 2300 mBm)
        (5230000 KHz - 5330000 KHz @ 40000 KHz), (600 mBi, 2300 mBm)
        (5735000 KHz - 5835000 KHz @ 40000 KHz), (600 mBi, 3000 mBm)
cfg80211: Calling CRDA for country: US
eth1: link up, 100Mbps, full-duplex, lpa 0x45E1
SCSI subsystem initialized
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
PPP generic driver version 2.4.2
tun: Universal TUN/TAP device driver, 1.6
tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
ip_tables: (C) 2000-2006 Netfilter Core Team
Driver 'sd' needs updating - please use bus_type methods
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
PCI: enabling device 0000:00:0f.2 (0140 -> 0142)
ehci_hcd 0000:00:0f.2: EHCI Host Controller
ehci_hcd 0000:00:0f.2: new USB bus registered, assigned bus number 1
ehci_hcd 0000:00:0f.2: irq 23, io mem 0x48002000
ehci_hcd 0000:00:0f.2: USB 2.0 started, EHCI 1.00
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 5 ports detected
PCI: enabling device 0000:00:0d.0 (0000 -> 0001)
sata_via 0000:00:0d.0: routed to hard irq line 9
scsi0 : sata_via
scsi1 : sata_via
scsi2 : sata_via
ata1: SATA max UDMA/133 port i16@0x1420 bmdma 0x1400 irq 25
ata2: SATA max UDMA/133 port i16@0x1430 bmdma 0x1408 irq 25
ata3: PATA max UDMA/133 port i16@0x1440 bmdma 0x1410 irq 25
usb 1-4: new high speed USB device using ehci_hcd and address 2
usb 1-4: configuration #1 chosen from 1 choice
ata1: SATA link down (SStatus 0 SControl 310)
ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
ata2.00: ATA-7: ST3160812AS, 3.AAE, max UDMA/133
ata2.00: 312581808 sectors, multi 0: LBA48 NCQ (depth 0/32)
ata2.00: configured for UDMA/133
isa bounce pool size: 16 pages
scsi 1:0:0:0: Direct-Access     ATA      ST3160812AS      3.AA PQ: 0 ANSI: 5
sd 1:0:0:0: [sda] 312581808 512-byte hardware sectors: (160 GB/149 GiB)
sd 1:0:0:0: [sda] Write Protect is off
sd 1:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sd 1:0:0:0: [sda] 312581808 512-byte hardware sectors: (160 GB/149 GiB)
sd 1:0:0:0: [sda] Write Protect is off
sd 1:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sda:<6>IMQ driver loaded successfully.
        Hooking IMQ before NAT on PREROUTING.
        Hooking IMQ after NAT on POSTROUTING.
sda1 sda2 < sda5 >
sd 1:0:0:0: [sda] Attached SCSI disk
nf_conntrack version 0.5.0 (2048 buckets, 8192 max)
CONFIG_NF_CT_ACCT is deprecated and will be removed soon. Please use
nf_conntrack.acct=1 kernel paramater, acct=1 nf_conntrack module option or
sysctl net.netfilter.nf_conntrack_acct=1 to enable it.
kjournald starting.  Commit interval 5 seconds
EXT3 FS on sda1, internal journal
EXT3-fs: recovery complete.
EXT3-fs: mounted filesystem with ordered data mode.
attempt to access beyond end of device
sda2: rw=0, want=4, limit=2
EXT3-fs: unable to read superblock
Micrel/Kendin KS8995 Ethernet switch SPI driver version 0.1.1
ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
PCI: enabling device 0000:00:0f.0 (0140 -> 0142)
ohci_hcd 0000:00:0f.0: OHCI Host Controller
ohci_hcd 0000:00:0f.0: new USB bus registered, assigned bus number 2
ohci_hcd 0000:00:0f.0: irq 23, io mem 0x48000000
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 3 ports detected
PCI: enabling device 0000:00:0f.1 (0140 -> 0142)
ohci_hcd 0000:00:0f.1: OHCI Host Controller
ohci_hcd 0000:00:0f.1: new USB bus registered, assigned bus number 3
ohci_hcd 0000:00:0f.1: irq 23, io mem 0x48001000
usb usb3: configuration #1 chosen from 1 choice
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 2 ports detected
uhci_hcd: USB Universal Host Controller Interface driver
Initializing USB Mass Storage driver...
scsi3 : SCSI emulation for USB Mass Storage devices
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
sd 1:0:0:0: Attached scsi generic sg0 type 0
spi-ks8995 spi32766.0: KS8995 device found, Chip ID:0, Revision:3
scsi 3:0:0:0: Direct-Access     Kingmax  USB2.0 FlashDisk 0.00 PQ: 0 ANSI: 2
sd 3:0:0:0: [sdb] 532479 512-byte hardware sectors: (272 MB/259 MiB)
sd 3:0:0:0: [sdb] Write Protect is off
sd 3:0:0:0: [sdb] Assuming drive cache: write through
sd 3:0:0:0: [sdb] 532479 512-byte hardware sectors: (272 MB/259 MiB)
sd 3:0:0:0: [sdb] Write Protect is off
sd 3:0:0:0: [sdb] Assuming drive cache: write through
sdb: sdb1
sd 3:0:0:0: [sdb] Attached SCSI removable disk
sd 3:0:0:0: Attached scsi generic sg1 type 0

yy5409

这个厉害的，要顶！！！

phantom-gy

除了赚眼球+rmb,毫无意义，鉴定完毕。

kemp

Memory: 128MB = 128MB total
Memory: 127560KB available (1964K code, 183K data, 96K init)

对这个比较有兴趣 改了128内存??? 可以上图吗?

system98

期待猫大放多一点细节方便我们菜鸟

3楼人品是亮点

qwea

4# kemp
升级128m没什么花头，也就是换2片64m的颗粒。主要是需要重新编译redboot激活。
那我再来show 一下最近研究的一台wrt300n v2的机器。原机配置4M FLASH 16M RAM IXP420 266M CPU.我升级了一下、现在是256m RAM用了4片64m叠焊，8M FLASH 并升级了一下cpu到533m。


RedBoot(tm) bootstrap and debug environment [ROM]
Red Hat certified release, version 2.02 - built 17:31:41, May 13 2009

Platform: Intel Generic Residential Gateway (IXP42X 533MHz) BE
Copyright (C) 2000, 2001, 2002, 2003, 2004 Red Hat, Inc.

RAM: 0x00000000-0x10000000, [0x00024a88-0x0ffe1000] available
FLASH: 0x50000000 - 0x50800000, 128 blocks of 0x00010000 bytes each.
== Executing boot script in 2.000 seconds - enter ^C to abort
RedBoot> eth

Trying NPE-B...success. Using NPE-B with PHY 16.
Trying NPE-C...success. Using NPE-C with PHY 1.
Ethernet eth0: MAC address 00:03:47:df:32:a8
IP: 192.168.1.1/255.255.255.0, Gateway: 0.0.0.0
Default server: 0.0.0.0
RedBoot> fis load kernel
RedBoot> exec
Using base address 0x00070000 and length 0x00101b94
Uncompressing Linux..................................................................... done, booting the kernel.
Linux version 2.6.28.10 (openwrt@openwrt-desktop) (gcc version 4.1.2) #8 Thu May 14 15:42:17 CST 2009
CPU: XScale-IXP42x Family [690541c1] revision 1 (ARMv5TE), cr=000039ff
CPU: VIVT data cache, VIVT instruction cache
Machine: Linksys WRT300N v2
Memory policy: ECC disabled, Data cache writeback
Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 65024
Kernel command line: root=/dev/mtdblock2 rootfstype=squashfs,jffs2 noinitrd console=ttyS0,115200 init=/etc/preinit
PID hash table entries: 1024 (order: 10, 4096 bytes)
Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
Memory: 256MB = 256MB total
Memory: 257468KB available (1928K code, 142K data, 92K init)
Calibrating delay loop... 532.48 BogoMIPS (lpj=2662400)
Mount-cache hash table entries: 512
CPU: Testing write buffer coherency: ok
net_namespace: 480 bytes
NET: Registered protocol family 16
IXP4xx: Using 16MiB expansion bus window size
PCI: IXP4xx is host
PCI: IXP4xx Using direct access for memory space
PCI: bus0: Fast back to back transfers enabled
NET: Registered protocol family 2
IP route cache hash table entries: 2048 (order: 1, 8192 bytes)
TCP established hash table entries: 8192 (order: 4, 65536 bytes)
TCP bind hash table entries: 8192 (order: 3, 32768 bytes)
TCP: Hash tables configured (established 8192 bind 8192)
TCP reno registered
NET: Registered protocol family 1
IXP4xx Queue Manager initialized.
squashfs: version 3.0 (2006/03/15) Phillip Lougher
Registering mini_fo version $Id$
JFFS2 version 2.2. (NAND) (SUMMARY)  漏 2001-2006 Red Hat, Inc.
msgmni has been set to 503
io scheduler noop registered
io scheduler deadline registered (default)
Serial: 8250/16550 driver4 ports, IRQ sharing disabled
serial8250.0: ttyS0 at MMIO 0xc8001000 (irq = 13) is a XScale
console [ttyS0] enabled
IXP4XX-Flash.0: Found 1 x16 devices at 0x0 in 16-bit bank
Amd/Fujitsu Extended Query Table at 0x0040
number of CFI chips: 1
cfi_cmdset_0002: Disabling erase-suspend-program due to code brokenness.
Searching for RedBoot partition table in IXP4XX-Flash.0 at offset 0x7f0000
5 RedBoot partitions found on MTD device IXP4XX-Flash.0
Creating 5 MTD partitions on "IXP4XX-Flash.0":
0x00000000-0x00080000 : "RedBoot"
0x00080000-0x00190000 : "kernel"
0x00190000-0x007f0000 : "rootfs"
mtd: partition "rootfs" set to be root filesystem
mtd: partition "rootfs_data" created automatically, ofs=460000, len=390000
0x00460000-0x007f0000 : "rootfs_data"
0x007f0000-0x007ff000 : "FIS directory"
0x007ff000-0x00800000 : "RedBoot config"
i2c /dev entries driver
IXP4xx Watchdog Timer: heartbeat 60 sec
TCP westwood registered
NET: Registered protocol family 17
802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>
All bugs added by David S. Miller <davem@redhat.com>
XScale DSP coprocessor detected.
drivers/rtc/hctosys.c: unable to open rtc device (rtc0)
VFS: Mounted root (squashfs filesystem) readonly.
Freeing init memory: 92K
Please be patient, while OpenWrt loads ...

qwea

root@OpenWrt:/# free
              total         used         free       shared      buffers
  Mem:       257784        15764       242020            0         1908
Swap:            0            0            0
Total:       257784        15764       242020
root@OpenWrt:/# df
Filesystem           1k-blocks      Used Available Use% Mounted on
rootfs                    2880      2880         0 100% /
/dev/root                 2880      2880         0 100% /rom
/dev/mtdblock3            3648       280      3368   8% /jffs
mini_fo:/jffs             2880      2880         0 100% /
root@OpenWrt:/# memtester 240M
memtester version 4.0.8 (32-bit)
Copyright (C) 2007 Charles Cazabon.
Licensed under the GNU General Public License version 2 (only).

pagesize is 4096
pagesizemask is 0xfffff000
want 240MB (251658240 bytes)
got  240MB (251658240 bytes), trying mlock ...locked.
Loop 1:
  Stuck Address       : ok         
  Random Value        : ok
  Compare XOR         : ok
  Compare SUB         : ok
  Compare MUL         : ok
  Compare DIV         : ok
  Compare OR          : ok
  Compare AND         : ok
  Sequential Increment: ok
  Solid Bits          : ok         
  Block Sequential    : ok         
  Checkerboard        : ok         
  Bit Spread          : ok         
  Bit Flip            : ok         
  Walking Ones        : ok         
  Walking Zeroes      : ok         

Loop 2:
  Stuck Address       : ok         
  Random Value        : ok
  Compare XOR         : ok
  Compare SUB         : ok
  Compare MUL         : ok
  Compare DIV         : ok
  Compare OR          : ok
  Compare AND         : ok
  Sequential Increment: ok
  Solid Bits          : ok         
  Block Sequential    : setting 145

yuzt

看到传说中的叠焊了

kokoyu

纯围观!!!

scampking

只看到2片内存，没看出4片叠焊，不太明白，纯外行围观

ensan

技术水平就是高， 佩服。

szhuang50

我要内存芯片

8884361

只看到2片内存，没看出4片叠焊，不太明白，纯外行围观
scampking 发表于 2009-5-18 08:25

高度以及引腳焊點注目~~~

hick

魔道？....

jason930

如果我能擁有一部就爽了
很想買一部來玩