【AP模式】编译了一个K2P固件，推荐AP模式，很小很精简，不到5MB

yanzihui

这里有新编译的能够兼顾路由和AP两种模式的固件。
没有改机的E1/K2/K2P固件

新编译的padavan固件，E1物理口作为wan口，这样就可以作为路由使用了

https://www.right.com.cn/forum/thread-368257-1-1.html



================================================



编译了一个K2P固件，推荐使用AP模式，很精简，不建议路由模式使用。

AP模式不需要那么多占用资源的东西，编译选项如下。



编译环境：WIN10 Subsystem for Linux / KALI LINUX

同步源：git clone --depth=1 https://gitee.com/hanwckf/rt-n56u.git /opt/rt-n56u

感谢源码开源作者hanwckf

config文件选项：
=========================================



### Target Vendor/Product (support only Ralink RT3883/MT7620/MT7621/MT7628)
CONFIG_VENDOR=Ralink
CONFIG_PRODUCT=MT7621

### Target ProductID (board select, max 12 symbols)
CONFIG_FIRMWARE_PRODUCT_ID="K2P"

### Linux kernel and toolchain
CONFIG_FIRMWARE_INCLUDE_SFE=n

CONFIG_LINUXDIR=linux-3.4.x
CONFIG_TOOLCHAIN_DIR=/opt/rt-n56u/toolchain-mipsel

############################################################
### Linux kernel configuration
############################################################

### Build ROOTFS_IN_RAM firmware mode (kernel+initramfs).
### Decreased firmware size, but more RAM used, slow boot.
### Also allow build image for load w/o flash from UART console
#CONFIG_FIRMWARE_TYPE_ROOTFS_IN_RAM=y

### Force MT7621 CPU clock to 900MHz (override Uboot settings)
#CONFIG_FIRMWARE_CPU_900MHZ=y

### Enable MT7621 CPU sleep mode (downclock to 220MHz on idle)
#CONFIG_FIRMWARE_CPU_SLEEP=y

### Kernel driver select for WiFi AP 2.4GHz
CONFIG_FIRMWARE_WIFI2_DRIVER=4.4.2.1

### Kernel driver select for WiFi AP 5GHz
CONFIG_FIRMWARE_WIFI5_DRIVER=4.4.2.1

### Enable IPv6 support
CONFIG_FIRMWARE_ENABLE_IPV6=n

### Enable USB support
CONFIG_FIRMWARE_ENABLE_USB=n

### Enable NTFS filesystem support via Paragon "ufsd" driver. ~0.4MB
CONFIG_FIRMWARE_ENABLE_UFSD=n

### Enable FAT/FAT32 filesystem support. ~0.1MB
CONFIG_FIRMWARE_ENABLE_FAT=n

### Enable exFAT (FAT/FAT32 too) filesystem support. ~0.12MB
CONFIG_FIRMWARE_ENABLE_EXFAT=n

### Enable EXT2 filesystem support. ~0.1MB
CONFIG_FIRMWARE_ENABLE_EXT2=n

### Enable EXT3 filesystem support. ~0.2MB
CONFIG_FIRMWARE_ENABLE_EXT3=n

### Enable EXT4 (EXT3/2 too) filesystem support. ~0.4MB
CONFIG_FIRMWARE_ENABLE_EXT4=n

### Enable XFS filesystem support. ~0.6MB
CONFIG_FIRMWARE_ENABLE_XFS=n

### Enable FUSE (filesystems in userspace) support. ~0.1MB
CONFIG_FIRMWARE_ENABLE_FUSE=n

### Enable swap files/partitions support. ~0.05MB
CONFIG_FIRMWARE_ENABLE_SWAP=n

### Include UVC camera modules. ~0.2MB
CONFIG_FIRMWARE_INCLUDE_UVC=n

### Include USB-HID modules. ~0.2MB
CONFIG_FIRMWARE_INCLUDE_HID=n

### Include USB-Serial modules (e.g. pl2303). ~0.03MB
CONFIG_FIRMWARE_INCLUDE_SERIAL=n

### Include USB-Audio modules ~0.46MB
CONFIG_FIRMWARE_INCLUDE_AUDIO=n

### Include XFRM (IPsec) modules & iptables extension ~ 0.2MB
CONFIG_FIRMWARE_INCLUDE_XFRM=n

### Include network QoS scheduling modules. ~0.2MB
CONFIG_FIRMWARE_INCLUDE_QOS=n

### Include IMQ module for shapers (a bit of performance degradation). ~0.02MB
CONFIG_FIRMWARE_INCLUDE_IMQ=n

### Include IFB module for shapers. ~0.03MB
CONFIG_FIRMWARE_INCLUDE_IFB=n

### Include IPSet utility and kernel modules. ~0.4MB
CONFIG_FIRMWARE_INCLUDE_IPSET=n

### Include NFSv3 server. ~0.6MB
CONFIG_FIRMWARE_INCLUDE_NFSD=n

### Include NFSv3 client. ~0.5MB
CONFIG_FIRMWARE_INCLUDE_NFSC=n

### Include CIFS (SMB) client. ~0.2MB
CONFIG_FIRMWARE_INCLUDE_CIFS=n

############################################################
### Userspace configuration
############################################################

### Include WebUI international resources. Increased firmware size
CONFIG_FIRMWARE_INCLUDE_LANG_CN=y
#CONFIG_FIRMWARE_INCLUDE_LANG_BR=y
#CONFIG_FIRMWARE_INCLUDE_LANG_CZ=y
#CONFIG_FIRMWARE_INCLUDE_LANG_DA=y
#CONFIG_FIRMWARE_INCLUDE_LANG_DE=y
#CONFIG_FIRMWARE_INCLUDE_LANG_ES=y
#CONFIG_FIRMWARE_INCLUDE_LANG_FI=y
#CONFIG_FIRMWARE_INCLUDE_LANG_FR=y
#CONFIG_FIRMWARE_INCLUDE_LANG_NO=y
#CONFIG_FIRMWARE_INCLUDE_LANG_PL=y
#CONFIG_FIRMWARE_INCLUDE_LANG_RU=y
#CONFIG_FIRMWARE_INCLUDE_LANG_SV=y
#CONFIG_FIRMWARE_INCLUDE_LANG_UK=y

### Include NTFS-3G FUSE driver (instead of Paragon "ufsd"). ~0.4MB
CONFIG_FIRMWARE_INCLUDE_NTFS_3G=n

### Include LPR printer daemon. ~0.12MB
CONFIG_FIRMWARE_INCLUDE_LPRD=n

### Include USB-over-Ethernet printer daemon. ~0.05MB
CONFIG_FIRMWARE_INCLUDE_U2EC=n

### Include "tcpdump" utility. ~0.6MB
CONFIG_FIRMWARE_INCLUDE_TCPDUMP=n

### Include "hdparm" utility (allow set HDD spindown timeout and APM). ~0.1MB
CONFIG_FIRMWARE_INCLUDE_HDPARM=n

### Include "parted" utility (allow make GPT partitions). ~0.3MB
CONFIG_FIRMWARE_INCLUDE_PARTED=n

### Include SMB (and WINS) server. ~1.5MB
CONFIG_FIRMWARE_INCLUDE_SMBD=n

### using samba3.6 instead of samba3
CONFIG_FIRMWARE_INCLUDE_SMBD36=n

### Include WINS server only. ~0.4MB
CONFIG_FIRMWARE_INCLUDE_WINS=n

### Include syslog for SMB and WINS server. ~0.3MB
CONFIG_FIRMWARE_INCLUDE_SMBD_SYSLOG=n

### Include FTP server. ~0.2MB
CONFIG_FIRMWARE_INCLUDE_FTPD=n

### Include alternative L2TP control client RP-L2TP. ~0.1MB
CONFIG_FIRMWARE_INCLUDE_RPL2TP=n

### Include EAP-TTLS and EAP-PEAP authentication support. openssl ~1.2MB, wpa_supplicant +0.04MB
CONFIG_FIRMWARE_INCLUDE_EAP_PEAP=y

### Include HTTPS support for DDNS client. openssl ~1.2MB
CONFIG_FIRMWARE_INCLUDE_DDNS_SSL=n

### Include HTTPS support. openssl ~1.2MB
CONFIG_FIRMWARE_INCLUDE_HTTPS=n

### Include sftp-server. openssl ~1.2MB, sftp-server ~0.06MB
CONFIG_FIRMWARE_INCLUDE_SFTP=n

### Include dropbear SSH. ~0.3MB
CONFIG_FIRMWARE_INCLUDE_DROPBEAR=n

### Make the dropbear symmetrical ciphers and hashes faster. ~0.06MB
CONFIG_FIRMWARE_INCLUDE_DROPBEAR_FAST_CODE=n

### Include OpenSSH instead of dropbear. openssl ~1.2MB, openssh ~1.0MB
CONFIG_FIRMWARE_INCLUDE_OPENSSH=n

### Include Openvirtual**. IPv6 required. openssl ~1.2MB, openvirtual** ~0.4MB
CONFIG_FIRMWARE_INCLUDE_OPENvirtual**=n

### Include StrongSwan. XFRM modules ~0.2MB, strongswan ~0.7MB
CONFIG_FIRMWARE_INCLUDE_SSWAN=n

### Include Elliptic Curves (EC) to openssl library. ~0.1MB
CONFIG_FIRMWARE_INCLUDE_OPENSSL_EC=n

### Include "openssl" executable for generate certificates. ~0.4MB
CONFIG_FIRMWARE_INCLUDE_OPENSSL_EXE=n

### Include xUPNPd IPTV mediaserver. ~0.3MB
CONFIG_FIRMWARE_INCLUDE_XUPNPD=n

### Include Minidlna UPnP mediaserver. ~1.6MB
CONFIG_FIRMWARE_INCLUDE_MINIDLNA=n

### Include Firefly iTunes mediaserver. ~1.0MB
CONFIG_FIRMWARE_INCLUDE_FIREFLY=n

### Include ffmpeg 0.11.x instead of 0.6.x for Minidlna and Firefly. ~0.1MB
CONFIG_FIRMWARE_INCLUDE_FFMPEG_NEW=n

### Include Transmission torrent. openssl ~1.2MB, transmission ~1.5MB
CONFIG_FIRMWARE_INCLUDE_TRANSMISSION=n

### Include Transmission-Web-Control (advanced WebUI). ~0.8MB
CONFIG_FIRMWARE_INCLUDE_TRANSMISSION_WEB_CONTROL=n

### Include Aria2 download manager. openssl ~1.2MB, aria2 ~3.5MB
CONFIG_FIRMWARE_INCLUDE_ARIA=n

### Include Aria2 new version instead of old version (prebuild by gcc 4.9.4)
CONFIG_FIRMWARE_INCLUDE_ARIA2_NEW_PREBUILD_BIN=n

### Include Aria2 WEB control. ~0.7MB
CONFIG_FIRMWARE_INCLUDE_ARIA_WEB_CONTROL=n

CONFIG_APPLY_PROMETHEUS_WIFI_DRIVER_PATCH=n

CONFIG_FIRMWARE_INCLUDE_CURL=n

CONFIG_FIRMWARE_INCLUDE_SCUTCLIENT=n

CONFIG_FIRMWARE_INCLUDE_GDUT_DRCOM=n

CONFIG_FIRMWARE_INCLUDE_DOGCOM=n

CONFIG_FIRMWARE_INCLUDE_MINIEAP=n

CONFIG_FIRMWARE_INCLUDE_NJIT_CLIENT=n

CONFIG_FIRMWARE_INCLUDE_NAPT66=n

CONFIG_FIRMWARE_INCLUDE_s-s=n

CONFIG_FIRMWARE_INCLUDE_SSSERVER=n

CONFIG_FIRMWARE_INCLUDE_SOFTETHERvirtual**_CLIENT=n

CONFIG_FIRMWARE_INCLUDE_SOFTETHERvirtual**_CMD=n

CONFIG_FIRMWARE_INCLUDE_DNSMASQ_CHINA_CONF=n

CONFIG_FIRMWARE_INCLUDE_DNSFORWARDER=n

CONFIG_FIRMWARE_INCLUDE_china-dns=n

CONFIG_FIRMWARE_INCLUDE_VLMCSD=n

CONFIG_FIRMWARE_INCLUDE_TTYD=n

CONFIG_FIRMWARE_INCLUDE_LRZSZ=n

CONFIG_FIRMWARE_INCLUDE_HTOP=n

CONFIG_FIRMWARE_INCLUDE_NANO=n

CONFIG_FIRMWARE_INCLUDE_IPERF=n

CONFIG_FIRMWARE_INCLUDE_IPERF3=n

CONFIG_FIRMWARE_INCLUDE_DUMP1090=n

CONFIG_FIRMWARE_INCLUDE_RTL_SDR=n

CONFIG_FIRMWARE_INCLUDE_MTR=n



======================================


File: K2P_AP_3.4.3.9-099.trx
Size: 4894487 bytes
Modified: 2018年11月19日, 15:21:47
MD5: 061BBFAA944B4FD597B657F33BEE5F0E
SHA1: AB1BC79F0E41D584BECE21EFCCCFBADEA79D5E94
CRC32: F7B239F0
链接: https://pan.baidu.com/s/1gxGwdUE5ZcMLVm2TDiK4zA 提取码:ip78  ip78





在上面的基础上修改 CONFIG_FIRMWARE_INCLUDE_EAP_PEAP=n 再来一个更精简的版本。

File: K2P_3.4.3.9-099-n.trx
Size: 4412905 bytes
Modified: 2018年11月19日, 21:10:38
MD5: F1492DB088831CE41408F1A66B9A6F7F
SHA1: 030567159D13B2D3C164F3EAE633CB868677ACDB
CRC32: F742A376
链接: https://pan.baidu.com/s/1BJYiTbcj9fD0-wlFdj24gQ 提取码:6538 6538

kingbad

坐小板凳慢慢看

virginlulu

原版内存做ap不错

hcyme

最精简版本

401626436

楼主怎么搞的无线？我用别人发的所谓的泄露SDK编译，有无线选项但死活不能用一直都是未启用状态，丢15.05也是一个样，请指点一下迷津，蟹蟹!

TEDDDDD

试试哦，用下这个版本

Yangzai

谢谢分享，试试看有没有WDS模式

微笑生活

小板凳往前挤挤

xysck

谢谢提供。

an1860a

可以下载么？？？？？

LittlepopKaka

大多数得到

sxlouxinkun

坐小板凳慢慢看

快奔三还没二够

不错的版本

kEv1n

支持下·············

footlog

401626436 发表于 2018-11-19 20:01
楼主怎么搞的无线？我用别人发的所谓的泄露SDK编译，有无线选项但死活不能用一直都是未启用状态，丢15.05也 ...

我也用hanwckf的编译成了
https://github.com/hanwckf/rt-n56u
7615的驱动是4.4.2的
我编的过程中发现hw_nat不能打开，打开wifi就不能用，不知道怎么回事