|
|
楼主 |
发表于 2010-6-22 16:35
|
显示全部楼层
试验得出那个接口并不是JTAG 而是 TTL ，现在已用TTL得到启动信息，但是为什么进不了CFE 模式。
Flash ID : 0x22a222a2
manufacture ID : 0x000000ec
Flash Vendor : K8D3216UBC(supported)
========================================================================
KS8695PX BootLoader ver 2.1 2008.03.19
(16 MB DRAM, 4 MB ROM)
-- TIMER1, FLASH_BASE[0x2000000]
-- BZIP2 Algorithm
Press ESC key when boot!! Otherwise automatically start linux
========================================================================
Source = 0x02010000, Destination = 0x00008000, SourceLen = 0x003ec000, DestLen = 0x007f0000
Decompressing....
Normal Terminition...
Create Mapping : vir = 0xc0000000, phy = 0x00000000
Create Mapping : vir = 0xffff0000, phy = 0x00001000
Create Mapping : vir = 0xf3ff0000, phy = 0x03ff0000
Create Mapping : vir = 0xf2000000, phy = 0x02000000
Create Mapping : vir = 0xe0000000, phy = 0x10000000
Create Mapping : vir = 0xf8000000, phy = 0x08000000
Create Mapping : vir = 0xf0ffa000, phy = 0x00ffa000
Create Mapping : vir = 0xf0ffb000, phy = 0x00ffb000
Linux version 2.4.18-rmk7 (whiterock@Canaria.localdomain) (gcc version 2.95.4 20010319 (prerelease)) #1040 Wed Jan 23 10:59:13 KST 2008
CPU: ARM/ALTERA Arm922Tid(wb) revision 0
Machine: KS8695
Warning: bad configuration page, trying to continue
Security risk: creating user accessible mapping for 0x03ff0000 at 0xf3ff0000
Security risk: creating user accessible mapping for 0x02000000 at 0xf2000000
Security risk: creating user accessible mapping for 0x00ffa000 at 0xf0ffa000
Security risk: creating user accessible mapping for 0x00ffb000 at 0xf0ffb000
On node 0 totalpages: 4090
zone(0): 4090 pages.
zone(1): 0 pages.
zone(2): 0 pages.
Kernel command line:
Calibrating delay loop... 83.14 BogoMIPS
Memory: 15MB = 15MB total
Memory: 14628KB available (1124K code, 250K data, 56K init)
Dentry-cache hash table entries: 2048 (order: 2, 16384 bytes)
Inode-cache hash table entries: 1024 (order: 1, 8192 bytes)
Mount-cache hash table entries: 512 (order: 0, 4096 bytes)
Buffer-cache hash table entries: 1024 (order: 0, 4096 bytes)
Page-cache hash table entries: 4096 (order: 2, 16384 bytes)
POSIX conformance testing by UNIFIX
PCI: bus0: Fast back to back transfers disabled
Linux NET4.0 for Linux 2.4
Based upon Swansea University Computer Society NET3.039
Initializing RT netlink socket
Starting kswapd
ttyS0 at MEM 0x3ffe000 (irq = 8) is a KS8695
block: 64 slots per queue, batch=16
RAMDISK driver initialized: 16 RAM disks of 4096K size 1024 blocksize
eth info: AnyGate Wired Ethernet Driver
, version 2.99, Copyright (c) 2003-4 AirLink Technology, Inc.
eth info: Icache mode = roundrobin
PPP generic driver version 2.4.1
imq driver loaded.
NEW_RESET Device Driver is installed
init_altech_mtd: chip probing count 0
Amd/Fujitsu Extended Query Table v3.3 at 0x0040
number of CFI chips: 1
cfi_cmdset_0002: Disabling fast programming due to code brokenness.
init_altech_mtd: bank1, name:ALTECH0, size:4194304bytes
ALTECH flash0: Using Static image partition definition
Creating 5 MTD partitions on "ALTECH0":
0x00000000-0x00010000 : "bios"
0x003f0000-0x00400000 : "param"
0x00010000-0x003f0000 : "systemsw"
0x000a0000-0x003f0000 : "cramfs"
0x00000000-0x003f0000 : "ets_partition"
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP
IP: routing cache hash table of 512 buckets, 4Kbytes
TCP: Hash tables configured (established 512 bind 512)
ip_conntrack version 2.1 (127 buckets, 1016 max) - 440 bytes per conntrack
ip_tables: (C) 2000-2002 Netfilter core team
init netfilter IMQ
NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
NET4: Ethernet Bridge 008 for NET4.0
NetWinder Floating Point Emulator V0.95 (c) 1998-1999 Rebel.com
VFS: Mounted root (cramfs filesystem) readonly.
Freeing init memory: 56K
init started: BusyBox v0.60.5 (2008.01.23-01:57+0000) multi-call binary
Setting hostname ...
Mounting root fs rw ...
Mounting other filesystems ...
*TYPE3-Current MAC Address is 00:02:a8:97:4b:10, 00:02:a8:97:4b:13
flash : MAC Check OK...
flash : Read Bios from flash memory...
checksum bbc9f77e, tmp_checksum bbc9f77e
flash : Read from flash memory...
sysconf read 0xf0ffb000
sysconf read end
Factory Init = 0
config_snmpd
sysconf read 0xf0ffb000
sysconf read end
eth info: TXDESC> DataBuf=0xc0e5d000, Descriptor=0xc1429000, PA=0x00d76000
eth info: RXDESC> DataBuf=0xc0d78000, Descriptor=0xc1412000, PA=0x00d75000
device eth0 entered promiscuous mode
ra0 mac is 0x00:02:a8:97:4b:10
br0: port 1(eth0) entering listening state
eth info: TXDESC> DataBuf=0xc0d3f000, Descriptor=0xc142c000, PA=0x00d2e000
eth info: RXDESC> DataBuf=0xc0d34800, Descriptor=0xc142f000, PA=0x00d38000
device eth1 entered promiscuous mode
Using /lib/modules/2.4.18-rmk7/kernel/drivers/net/wireless/RT2561/rt61ap.o
Warning: loading rt61ap will taint the kernel: no license
See http://www.tux.org/lkml/#export-tainted for information about tainted modules
br0: port 1(eth0) entering learning state
br0: port 1(eth0) entering forwarding state
br0: topology change detected, propagating
device ra0 entered promiscuous mode
ra0 mac is 0x00:02:a8:97:4b:10
br0: port 2(ra0) entering listening state
device ra1 entered promiscuous mode
ra0 mac is 0x00:02:a8:97:4b:10
br0: port 3(ra1) entering listening state
br0: port 2(ra0) entering learning state
br0: port 3(ra1) entering learning state
br0: port 2(ra0) entering forwarding state
br0: topology change detected, propagating
br0: port 3(ra1) entering forwarding state
br0: topology change detected, propagating
udhcpc (v0.9.9) started
udhcpd (v0.9.9) started
Unable to open /etc/config/udhcpd.leases for reading
Unable to open /etc/config/udhcpd.assigned for reading
*IP(eth1) has changed... 0.0.0.0
IP is lost...
Sending discover...
Sending discover...
create_sysconf_linux_module
Sysinit done
login: |
|
IP卡
狗仔卡
发表于 2010-6-19 16:52
置顶卡
沉默卡
喧嚣卡
顶贴卡
显身卡
这个芯片很少见。。。继续等待吧