|
|
U-Boot 1.1.4--LSDK-10.2.r2-00013-4 (Nov 4 2015 - 23:49:40)
ap135 - Scorpion 1.0DRAM:
sri
Scorpion 1.0
ath_ddr_initial_config(196): (32bit) ddr2 init
tap = 0x00000003
Tap (low, high) = (0x4, 0x1f)
Tap values = (0x11, 0x11, 0x11, 0x11)
128 MB
Top of RAM usable for U-Boot at: 88000000
Reserving 247k for U-Boot at: 87fc0000
Reserving 192k for malloc() at: 87f90000
Reserving 44 Bytes for Board Info at: 87f8ffd4
Reserving 36 Bytes for Global Data at: 87f8ffb0
Reserving 128k for boot params() at: 87f6ffb0
Stack Pointer at: 87f6ff98
Now running in RAM - U-Boot at: 87fc0000
Flash Manuf Id 0xc2, DeviceId0 0x20, DeviceId1 0x18
flash size 16MB, sector count = 256
Flash: 16 MB
*** Warning *** : PCIe WLAN Module not found !!!
In: serial
Out: serial
Err: serial
Net: ath_gmac_enet_initialize...
athrs_sgmii_res_cal: cal value = 0x1
No valid address in Flash. Using fixed address
ath_gmac_enet_initialize: reset mask:c02200
mac:0 Registering AR8033_PHY ....
eth0 phy address 7 Phy ID 4d:d074
WASP ----> AR8033 PHY *
: cfg1 0x80000000 cfg2 0x7114
eth0: 00:03:7f:09:0b:ad
eth0 phy address 7 Phy ID 4d:d074
chip configure: 0122
chip configure: 810b
phy mode: copper
AR8033: Auto-Negotiation Success
eth0 up
eth0
i2c init successful
Setting 0x18116290 to 0x50a0214f
Hit Ctrl+B to stop autoboot: 0
ath> hel
? - alias for 'help'
autoscr - run script from memory
base - print or set address offset
bdinfo - print Board Info structure
boot - boot default, i.e., run 'bootcmd'
bootd - boot default, i.e., run 'bootcmd'
bootelf - Boot from an ELF image in memory
bootm - boot application image from memory
bootp - boot image via network using BootP/TFTP protocol
bootvx - Boot vxWorks from an ELF image
cfg - Config the data of manu area
cmp - memory compare
coninfo - print console devices and information
cp - memory copy
crc32 - checksum calculation
dhcp - invoke DHCP client to obtain IP/boot params
echo - echo args to console
erase - erase FLASH memory
ethreg - Switch/PHY Reg rd/wr utility
exit - exit script
flinfo - print FLASH memory information
go - start application at address 'addr'
help - print online help
icrc32 - checksum calculation
iloop - infinite loop on address range
imd - i2c memory display
iminfo - print header information for application image
imm - i2c memory modify (auto-incrementing)
imw - memory write (fill)
inm - memory modify (constant address)
iprobe - probe to discover valid I2C chip addresses
itest - return true/false on integer compare
loadb - load binary file over serial line (kermit mode)
loads - load S-Record file over serial line
loady - load binary file over serial line (ymodem mode)
loop - infinite loop on address range
mct - simple RAM test
md - memory display
mii - MII utility commands
mm - memory modify (auto-incrementing)
mtest - simple RAM test
mw - memory write (fill)
nfs - boot image via network using NFS protocol
nm - memory modify (constant address)
pci - list and access PCI Configuration Space
ping - send ICMP ECHO_REQUEST to network host
pll cpu-pll dither ddr-pll dither - Set to change CPU & DDR speed
pll erase
pll get
printenv- print environment variables
progmac - Set ethernet MAC addresses
progmac2 - Set ethernet MAC addresses
protect - enable or disable FLASH write protection
rarpboot- boot image via network using RARP/TFTP protocol
reset - Perform RESET of the CPU
run - run commands in an environment variable
saveenv - save environment variables to persistent storage
setenv - set environment variables
sleep - delay execution for some time
test - minimal test like /bin/sh
tftpboot- boot image via network using TFTP protocol
version - print monitor version
ath> printenv
bootdelay=4
baudrate=115200
ethaddr=0x00:0xaa:0xbb:0xcc:0xdd:0xee
dir=
lu=tftp 0x80060000 u-boot.bin&&erase 0x9f000000 +$filesize&&cp.b $fileaddr 0x9f000000 $filesize
lf=tftp 0x80060000 ap135${bc}-jffs2&&erase 0x9f060000 +0x680000&&cp.b $fileaddr 0x9f060000 $filesize
lk=tftp 0x80060000 vmlinux${bc}.lzma.uImage&&erase 0x9f6e0000 +$filesize&&cp.b $fileaddr 0x9f6e0000 $filesize
art=tftp 0x80ffffc0 ap135-ramdisk.img && $bootcmd 0x80ffffc0
eth0addr=00:03:7f:09:0b:a0
filesize=108d17
fileaddr=80060000
ethact=eth0
ipaddr=172.20.90.234
serverip=172.20.90.5
bootargs=console=ttyS0,115200 root=31:03 rootfstype=squashfs init=/sbin/init mtdparts=ath-nor0:256k(u-boot)ro,64k(u-boot-env),64k(board),6656k(rootfs0),1m(uImage0),6656k(rootfs1),1m(uImage1),448k(config),64k(exception),64k(log),64k(ART),7680k@384k(FMW0),7680k@8064k(FMW1)
bootcmd=bootm 0x9f6e0000
stdin=serial
stdout=serial
stderr=serial
Environment size: 892/65532 bytes
ath>
情况是这样 更换BREED 网口无输出 不能更换BOOT 只能在原机BOOT 刷机OPENWRT 或者集客 PS 我有编程器 但是在与研究求学
|
|
IP卡
狗仔卡
发表于 2023-12-1 08:15
置顶卡
沉默卡
喧嚣卡
顶贴卡
显身卡